Sharp PC410 Datasheet
PC410
PC410
Compact, Surface Mount
Ultra-high Speed Response
OPIC Photocoupler
■ Features ■ Outline Dimensions
1. Mini-flat package
2. Ultra-high speed response
654
PC410
1
± 0.3
3.6
1 Anode
3 Cathode
)
1.27
0.4
3
6˚
(t
PLH
, t
: TYP. 50ns at RL= 350Ω
PHL
)
3. Isolation voltage between input and output
)
(V
: 2 500 V
iso rms
4. Instantaneous common mode rejection
voltage CM
: TYP. 500V/µs
H
Anode mark
5. Recognized by UL(No.64380)
■ Applications
1. Hybrid substrate which requires high den-
sity mounting
2. Personal computers, office computers and
peripheral equipment
3. Electronic musical instruments
4. Audio equipment
■ Package Specifications
Model No.
PC410T Taping package(Net: 750pcs.
PC410Z Sleeve package(Net: 100pcs.
Package specifications
Taping package(Net:3 000pcs.) 370mm
PC410
Diameter of reel
)
)
Tape width
12mm
180mm
12mm
--
■ Absolute Maximum Ratings
Parameter Symbol Rating Unit
*1
Forward current
Input
Reverse voltage V
Power dissipation P mW
*2
Supply voltage
Output
High level output voltege
Low level output current
Output collector power dissipation
*3
Isolation voltege
Operating temperature T
Storage temperature T
*4
Soldering temperature
*1 Ta= 0 to + 70˚C
*2 For 1 minute MAX.
*3 AC for 1 minute, 40 to 60% RH. Apply the specified voltage between the whole of the
electrode pins on the input side and the whole of the electrode pins on the output side.
*4 For 10 seconds.
I
F
R
V
CC
V
OH
I
OL
P
O
V
iso
opr
stg
T
sol
* “OPIC ” (Optical IC) is a trademark of the SHARP Corporation.
An OPIC consists of a light-detecting element and signal processing circuit integrated onto a single chip.
(
Ta= 25˚C
20
5
40
7
7
50
85
2 500
0 to + 70
- 40 to + 125
260 ˚C
2.54
± 0.25
± 0.2
2.6
± 0.1
0.1
mW
V
mA
V
V
V
mA
rms
˚C
˚C
± 0.25
± 0.2
4.4
± 0.1
C0.4
(
Input Side
+ 0.4
0.5
- 0.2
4 GND
5 Vo
6 Vcc
Soldering area
(
Unit : mm
Internal connection
diagram
6
5
4
13
± 0.3
5.3
)
+ 0.2
7.0
- 0.7
0.2mm or more
)
± 0.05
0.2
“ In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that occur in equipment using any of SHARP's devices, shown in catalogs,
data books, etc. Contact SHARP in order to obtain the latest version of the device specification sheets before using any SHARP's device.”
PC410
■ Electro-optical Characteristics
Parameter Symbol Conditions
Forward voltage V
Input
Output
Transfer
charac-
teristics
Note) All typical values : at Ta= 25˚C, VCC=5V
Each characteristics shall be measured under opaque condition.
Reverse current IRTa= 25˚C, VR=5V
Terminal capacitance C
Low level output voltage
High level output current
Low level supply current
High level supply current I
“H→L” threshold input current I
Isolation resistance R
Floating capacitance
“H→L” propagation
delay time
“L→H” propagation
delay time
Response
time
Fall time
Rise time
Instantaneous common
mode rejection
voltage “ High level
output”
Instantaneous common
CMR
mode rejection
voltage “ Low level
output”
Ta= 25˚C, IF= 10mA
F
Ta= 25˚C, V = 0, f= 1MH
t
IOL= 13mA, VCC= 5.5V, IF= 5mA
V
OL
I
VCC=VO= 5.5V, I
OH
I
VCC= 5.5V, IF= 10mA
CCL
VCC= 5.5V, IF=0
CCH
VCC= 5V, VO= 0.8V, RL= 350Ω
FHL
Ta = 25˚C, DC500V, 40 to 60% RH
ISO
Ta= 25˚C, V = 0, f= 1MHz
C
f
t
PHL
Ta= 25˚C
V
= 5V, I
t
CMH
CC
PLH
RL= 350Ω , CL= 15pF
t
f
Fig. 1
t
r
I
=0
F
(
V
MIN.)=2V
O
IF= 5mA
L
(
V
MAX.)= 0.8V
O
CM
(
Ta= 0 to + 70˚C unless otherwise specified
MIN. TYP. MAX. Unit
- 1.6 1.9 V
--10µA
- 60 150
0.4-
0.6 V
- 2 250 µA
= 250m A
F
Z
-1318mA
- 7 15 mA
= 7.5mA
F
Ta= 25˚C
V
CC
VCM= 10V(Peak
R
L
=5V
= 350Ω
- 2.5 5 mA
5x101010
-
-
- 50 120
-3060
-3060
100 500 -
)
- 100 - 500 -
11
-
0.6 pF
50 120
-
Fig. 2
)
pF
Ω
ns
V/µs
■ Recommended Operation Conditions
Parameter Symbol MIN. MAX. Unit
Low level input current I
High level input current I
Supply voltage V
Fanout (TTL load) N - 8 -
Operating temperature T
Connect a by-pass ceramic capacitor (0.01 to 0.1µF) between VCC and GND at the
position within 1cm from lead pin.
0 250 µ A
FL
7 15 mA
FH
4.5 5.5 V
CC
0 70 ˚C
opr
Loading...