Sharp PC3H7A, PC3H7AB, PC3H7AC, PC3H7AD, PC3H7B Datasheet
...
APPROVED BY:
DATE:
ELECTRONIC COMPONENTS
GROUP SHARP CORPORATION
SPECIFICATION
PREPARED BY: DATE: 1
I
SPEC. No. ED-97123A
I
REPRESENTATIVE DMSION
I
OPTO-ELECTRONIC DEVICES DN.
DEVICE SPECIFICATION FOR
Business dealing name
PHOTOCOUPLER
MODEL No.
PC3H7
1. These specification sheets include materials protected under copyright of Sharp Corporation (“Sharp”).
Please do not reproduce or cause anyone to reproduce them without Sharp’s consent.
2. When using this product, please observe the absolute maximum ratings and the instructions for use outlined
in these specification sheets, as well as the precautions mentioned below. Sharp assumes no responsibility
for any damage resulting from use of the product which does not comply with the absolute maximum ratings
and the instructions included in these specification sheets, and the precautions mentioned below.
(Precautions)
(1) This product is designed for use in the following application areas :
i
l
OA equipment l Audio visual equipment
* Home appliances
* Telecommunication equipment CTerminal) * Measuring equipment
* Tooling machines * Computers
1
If the use of the product in the above application areas is for equipment listed in paragraphs
(2) or (3). please be sure to observe the precautions given in those respective paragraphs.
(2) Appropriate measures, such as fail-safe design and redundant design considering
the safety design of the overall system and equipment, should b-e taken to ensure reliability
and safety when this product is used for equipment which demands high reliability and
safety in function and precision, such as :
[
* Transportation control and safety equipment (aircraft, train, automobile etc.)
- Traffic signals
* Gas leakage sensor breakers
* Rescue and security equipment
* Other safety equipment
1
(3) Please do not use this product for equipment which require extremely high reliability
and safety in function and precision, such as ;
[
. Space equipment * Telecommunication equipment (for trunk lines)
* Nuclear power control equipment
* Medical equipment
1
(4) Please contact and consult with a Sharp sales representative if there are any questions
regarding interpretation of the above three paragraphs.
3. Please contact and consult with a Sharp sales representative for any questions about this product.
CUSTOMER’S APPROVAL
DATE
BY
DATE
PRESENTED
c-y- f I )
BY
L \ ‘h
T.
MatsumLua.
Department General Manager of
Engineering Dept. ,I1
Opto-Electronic Devices Div.
ELECOM Group
SHARP CORPORATION
SHARP CORPORATION
ED-97123A 1 September 30, 1998
MODEL No.
PAG E
PC3H7 l/11
1. Application
This specification applies to the outline and characteristics of photocoupler;
Model No. PC3H7.
2. Outline
Refer to the attached drawing
No.
CY8375K02.
3. Ratings and characteristics
Refer to the attached sheet, page 4 to 6.
4. Reliability
Refer to the attached sheet, page 7.
5. Incoming inspection
Refer to the attached sheet, page 8.
6. Supplement
6.1 Isolation voltage shall be measured in the foIlowing method.
(1) Short between anode and cathode on the primary side and between
collector and emitter on the secondary side.
(2) The dielectric withstand tester with zero-cross circuit shaIl be used.
(3) The wave form of applied voltage shall be a sine wave.
6.2 This product is not designed against irradiation.
This product is assembled with electrical input and output.
This product incorporates non-coherent light emitting diode.
6.3 Packaging specifications
Refer to the attached sheet, page 9 to 11.
SHARP CORPORATION
6.4
Collector current (Ic) Delivery rank table
(,, G” mark indicates business dealing name of ordered product)
ED-97123A
1 September 30, 199(
MODEL No. PAGE
PC3H7
2/11
6.5 ODS materials
This product shall not contain the following materials.
Also, the following materials shall not be used in the production process
for this product.
Materials for ODS : CFC,, Halon, Carbon tetrachloride.
1.1.1 -Trichloroethane (Methylchloroform)
6.6 Brominated flame retardants
Speclf?c bromlnated flame retardants such as the PBBO, and PBB, are not used
in this device at all.
7. Notes
Refer to the attached sheet- 1- 1, 2.
SHARP CORPORATION
ED-97123A
1 September 30, 199f
MODEL No.
PAG E
PC3H7
3/11
2. Outline
Rankmark
Date code l l
Anode mark
\
Pin Nos. and internal
connection diagram
Collector
Emitter
I
0.2
4.
4-to.
2
0
Anode
0
Cathode
Epoxy resin
Product mass : Approx. 0.05g
*1 ) 2 -digit number shall be marked according to DIN standard.
*21 Dimensions in parenthesis are shown for reference.
*3) Marking is laser marking
UNIT: l/l mm
PC3H7
Name
Drawing
No.
Outline Dimensions
(Business dealing
name : PC3H71
CY8375K02
SHARP CORPORATION
ED-97 123A
1 September 30, 199(
MODEL No.
PAG E
PC3H7
4/11
3. Ratings and characteristics
3.1 Absolute maximum ratings
Ta=25%
Emitter-collector voltage
V
EC0
6
V
output
Collector current Ic 50
mA
*l Collector power dissipation PC 150
mW
*l Total power dissipation Ptot
170 mW
Operating temperature Topr
-30 to +lOO
“C
Storage temperature
Tstg
-40 to +125
“C
*3 Isolation voltage vi.50
2.5 kVrms
l 4 Soldering temperature Tsol 260 “C
*l The derating factors of absolute maximum ratings due to ambient temperature
are shown in Fig. 1 to 4.
*2 Pulse widths100 ps, Duty ratio : 0.001 (Refer to Fig. 5)
*3 AC for 1 min. 40 to 6O%RH, f=GOHz
*4 ForlOs
Loading...