Sharp MX-M264U,MX-M264N,MX-M264NV,MX-M264NR,MX-M314U,MX-M314N,MX-M314NV,MX-M314NR,MX-M354U,MX-M354N,MX-M354NR Installation Manual

Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with
specified ones for maintaining the safety and performance of the set.

This document has been published to be used
for after sales service only.
The contents are subject to change without notice.

SHARP CORPORATION

INSTALLATION MANUAL

DIGITAL MULTIFUNCTIONAL SYSTEM

MX-M264U/M264N/
M264NV/M264NR
MX-M314U/M314N/
M314NV/M314NR
MX-M354U/M354N/354NR

MODEL

MX-M264U Transit, Installation (using) environment, Note - i

MX-M264U

5GTXKEG/CPWCN



Transit, Installation (using) environment, Note

* About a main unit illustration, it may differ from a target model.

1. Installing (use) conditions

Before installing the machine, check that the following installing
(use) conditions are satisfied.

If the installing (use) conditions are not satisfied, the machine may
not display full performances, resulting in troubles. It may also
cause safety problems. Therefore, be sure to arrange the installing
(use) conditions before setting up the machine.

A. Transportation space

For installation of a large size machine, be sure to check that the
door size is wide enough before bringing in.

B. Installing space

The following space must be provided around the machine in order
to assure machine performances and proper operations.

If any option is installed, provide the additional space for installing
it.

Adequate space must be provide behind the machine for proper
ventilation heat and dust. If not, the machine cannot exhibit func­tions against heat and dust, causing some troubles.

C. Power source (Capacity, voltage, frequency,

safety, plug)

If the power specifications are not satisfied, the machine cannot
exhibit full performances and may cause safety trouble.

Strictly observe the following specifications.

(1) Power capacity

Check that the following power capacity is satisfied. If not, addition­ally provide a power source.

Current capacity

Japan: 20A or more

EX 100V: 15A or more

EX 200V: 10A or more

NOTE: Check the shape of the power plug of the machine, and

insert it into a power outlet of the acceptable shape.

(2) Power voltage

Measure the voltage during copying to check that the voltage is in
the range of the specified voltage r10%.

If the voltage is outside the specified range, please have a certified
electrician upgrade the outlet.

(An electrical work is required.)

Use of a step-up transformer is also available. In this case, the
capacity must be great enough for the max. power consumption of
the machine.

(3) Power frequency, waveform

The frequency must be within the range of the specified frequency
r2%. If power waveform is deformed, a trouble may occur.

(4) Safety

Be sure to properly ground the machine.

Grounding (earth connection) must be performed before inserting
the power plug into the power outlet.

When disconnecting the earth connection, be sure to disconnect
the power plug from the power outlet in advance.

(5) Power plug

Check the shape of the power plug of the machine, and insert it into
a power outlet of the acceptable shape.
Power plug stated in power capacity.

D. Floor strength and level

This machine is considerably heavy and becomes heavier with an
option installed.

The floor must be strong enough to safely support the weight of the
machine as well as any installed options.

If the unit is not horizontally installed, the toner density control is not
performed normally, degrading the copy quality.

If not, color shift or image distortion may occur.
To assure proper Image quality, make sure the machine is setting
level.

E. Direct rays of the sun, dust, temperature,

humidity, gasses, chemicals, vibration

(1) Temperature and humidity (Environmental

conditions)

This machine is designed to perform properly under the specified
temperature and humidity. If the temperature and humidity exceeds
the specified range, the machine may not operate properly and or
cause equipment failure.

Especially when the humidity is too high, paper absorbs humidity to
cause a paper jam or dirty copy.

Do not install the machine near a heater, a cooler, or a humidifier.

Condensation may form inside the machine causing multiple trou­bles. Use enough care for ventilation.

No. Content

1 Transportation space
2 Installing space
3 Power source (Capacity, fluctuation, safety)
4 Floor strength
5 Direct rays of the sun, dust, temperature, humidity, gases,

chemicals

11-13/16"
(30cm)

11-13/16"
(30cm)

17-23/32"
(45cm)

MX-M264U Transit, Installation (using) environment, Note - ii

Operational environment

Temperature: 10 to 35qC

Humidity: 20 to 85% RH

Atmospheric pressure: 590 to 1013hPa (altitude: 0 to 2000 m)

(2) Contaminates

If dust enters the machine, it may cause dirty copy and a paper
jam, resulting in a shortened lifetime.

(3) Direct sunlight

If the machine is installed under the rays of the sun, the exterior of
the machine may be discolored and abnormal copies may be pro­duced.

(4) Gases and chemicals

Do not install the machine at a place where there are gases and
chemicals. Especially be careful to avoid installation near a diazo­type copier, which produces ammonium gas.

Copy quality may be adversely affected and a trouble may be
caused.

(5) Vibration

Avoid installation near a machine which produces vibrations.

If vibrations are applied to the copier machine, copy images may be
deflected and a trouble may be caused.

F. Note for handling PWB and electronic parts

When handling the PWB and the electronic parts, be sure to
observe the following precautions in order to prevent against dam­age by static electricity.

• When in transit or storing, put the parts in an anti-static bag or an
anti-static case and do not touch them with bare hands.

• When and after removing the parts from an anti-static bag (case),
use an earth band as shown below:

• Put an earth band to your arm, and connect it to the machine.

• When repairing or replacing an electronic part, perform the

procedure on an anti-static mat.

85%

Humidity㧔RH㧕

60%

20%

(50F)

(86F)

(95F)