Thank you for purchasing our product.
Please read this User’s Manual before
using the product. Change without Notice
Digital Video Recorder
User’s Guide
SATA HDD x 2
Audio input x 4
Dual monitor output
2
CAUTION
RISK OF ELECTRICAL
SHOCK. DO NOT OPEN !
CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK,
DO NOT REMOVE COVER (OR BACK), NO USER
SERVICEABLE PARTS REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
Safety Precautions
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of insulated
dangerous Voltage within the product’s enclosure that may be
sufficient magnitude to constitute risk of electrical shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operation and maintenance
(servicing) instructions in the literature accompanying the appliance.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT
EXPOSE UNITS NOT SPECIFICALLY DESIGNED FOR
Attention: installation should be performed by qualified service
Personnel only in accordance with the National Electrical Code or
applicable local codes.
Power Disconnect. Units with or without ON-OFF switches have
power supplied to the unit whenever the power cord is inserted into
the power source; however, the unit is operational only when the
ON-OFF switch is the ON position. The power cord is the main power
disconnect for all unites.
There are no serviceable parts for this unit, call for your agent for
details.
Warranty
and Service
3
Before installing stand alone DVR, be sure to thoroughly review and follow the instructions in
this Users Manual. Pay particular attention to the parts that are marked NOTICE.
Also, when connecting with external application, first turn the power OFF and follow manual
instruction for appropriate installation.
1. This document is intended for both the administrator and users of stand alone DVR
Model.
2. This manual contains information for configuring, managing and using stand alone
DVR Model.
3. To prevent fire or electrical shock, do not expose the product to heat or moisture
4. Be sure to read this manual before using stand alone DVR Model.
5. For questions and technical assistance of this product, contact your local dealer.
►Strong recommendation on installation of the DVR unit
1. Check electricity at the place you want to install the DVR unit is stable and meets our
electricity requirements. Unstable electricity will cause malfunction of the unit or give
critical damage to the unit.
2. Several chips on the main board of the DVR unit and hard disk drive inside the unit
generate heat, and it must be properly discharged. Do not put any objects just beside
exhaust port(fan) on the left side of the unit and do not close up an opening (fresh air
in-take) on the right side of the unit..
3. Put the DVR unit at well-ventilated place and do not put heat-generating objects on the
unit. When it is installed inside 19 inch mounting rack together with other devices,
please check built-in ventilation fan of the rack is properly running.
About this document
Before reading this document
4
FCC Statement:
WARNING
This device complies with Part 15 FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference. (2) This device must
accept any interference received including interference that may cause undesired
operation."
* Federal Communications Commission (FCC) Statement
WARNING
This Equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
* You are cautioned that changes or modifications not expressly approved by the party
responsible for compliance could void your authority to operate the equipment.
5
Please operate the keypad function according to the DVR model that you purchased
4CH DVR
1. : Quad screen mode button
2. CHANNEL 1 : Channel 1 full screen button
3. CHANNEL 2 : Channel 2 full screen button
4. CHANNEL 3 : Channel 3 full screen button
5. CHANNEL 4 : Channel 4 full screen button
8CH DVR
1. / : Split screen mode button
2. CHANNEL 1 / 5 : Channel 1 / 5 full screen button
3. CHANNEL 2 / 6 : Channel 2 / 6 full screen button
4. CHANNEL 3 / 7 : Channel 3 / 7 full screen button
5. CHANNEL 4 / 8 : Channel 4 / 8 full screen button
On live mode, press Enter button to (Shift) mode and then press number button 1; 2; 3 ; 4
switch to 5; 6; 7; 8 channel full screen.
FRONT PANEL
6
Miscellaneous
6. LOCK : Press this button to Key Lock function
7. AUDIO : Audio on or off button
8. AUTO : Auto sequence mode
9. BACKUP : Image backup button
10. UP / STOP : Direction button UP / Playback stop button /
11. DOWN / PAUSE : Direction button down / Playback pause / (Step play)
12. REW / LEFT : Reverse playback choose button / play speed /
13. FF / RIGHT : Forward playback choose button / play speed /
14. ENTER : Enter button or value change(+) / Shift mode(S)
15. MENU BUTTON : Press this button to display the menu setup
16. ESC / PTZ : Press this button to exit menu / PTZ mode
17. T-SRH : Press this button to playback time search
18. PLAY BUTTON : Press this button to playback
19. + BUTTON : Increase + values change.
20. REC BUTTON : Press this button to start recording image
21. - BUTTON : Reduce - values change
22. USB 2.0 : Pan Driver slot
*User needs to plug in USB again if ActiveX loaded; image backup or version updated.
7
REAR PANEL
Power code in 12V/5A, power switcher (ON / OFF)
4CH DVR Camera 1 ~ 4 input BNC type
8CH DVR Camera 1 ~ 8 input BNC type
Monitor out
Audio channel input x 1 and output x 1
Alarm / Relay / RS 485 connector
VGA out (Optional)
RJ-45 (Network connector)
PS 2 type mouse connector
8
System Operate:
1. NTSC / PAL auto detect is the default. Please power on DVR after camera 1 install.
2. Please set HDD to Master on PCB if only one is installed.
3. Press PLAY to format if a new hard disk is detected.
Mouse Control
Operate:
MENU BUTTON : Press MENU button to enter menu setup or exit
ESC / PTZ : Press ESC button to exit menu / To PTZ control mode
ENTER BUTTON : Press Enter button to confirm set or value change(+) / Shift mode
DIRECTION BUTTON : MENU item select
+ BUTTON : Increase + values change
- BUTTON : Reduce - values change
BACKUP : To backup mode
( ) MOVE (ENT) SELECT (MENU) EXIT
○1 Screen display
1. Double-click of the left button on desired camera
to full channel
2. Double-click of the left button on desired camera
to 9 split screen
○3 Menu display
1. One-click of the right button to menu OSD
2. Back to last OSD page
○2 None
No function
○1 Select
1. One-click on the item of OSD
2. One-click on the value of item
3. One-click on the Exit to quit and save menu
4. From right-up to left-below and the set motion
detect area
○1
○2
○3
9
Main Menu – Record Setup
Notice:
1. Frame rate adjustable under each mode per channel.
2. In 24 hours, user can adjust each channel frame rate
of different record mode. Such as schedule, motion
detection, and alarm record more.
3. Press button to change different of record modes.
Record Time Table: Base on 80GB HDD recording
Record Quality: Low. Average: 5 KB;
REC FPS 60 30 15 10
REC Hour 72 148 296 444
Record Quality: Normal. Average 10 KB;
REC FPS 60 30 15 10
REC Hour 36 74 148 222
Record Quality: High. Average 20 KB;
REC FPS 60 30 15 10
REC Hour 18 37 74 111
Actual recording time is base on live environment. This table is only for reference.
20 K x 30 (frame rate) x 60 (mins) x 60 (secs) = 2160000 K = 2160 M / hr
2160 M / hr x 24 = 51840000 K = 51840 M = 51.84 G / (1 Day)
Please format hard disk before starting recording after all the HDD installation
Hard disk compatible table
Seagate ST31000340AS 1TB
Seagate ST31000333AS 1TB
Seagate ST3750330AS 750GB
Seagate ST3500320AS 500GB
Seagate ST3250620AS 250GB
Hitachi HDS721075KLA330 750GB
Hitachi HCP725050GLA380 500GB
WD WD5000AACS 500GB
WD WD1600AAJS 160GB
10
Main Menu – System Set – Network Settings Network Settings – Local IP
1. Select STATIC / PPPOE / DHCP connection type
2. DNS only works under DDNS mode.
If the DVR is under a network system, suggest enable MENU – SYSTEM – TIME SETUP-
NTP server to get a network request automatically.
Main Menu – Search – Time Search
Press ENTER to select date and time. Direction left and right button to move value item.
ENTER or + / - button to change value.
11
Main Menu – Search – Time Search: after date and time select, go to Search and then
press ENTER to start playback.
Main Menu – Search – Event List
Select an event item of lists and then press ENTER to start to play.
“*” it means only a record of the event lists, but it can not to be playback
Playing
Forward speed: x 2 / x 3 / x 4
(Direction right button)
Reverse speed: x 8 / x 16 / x 32
(Direction left button)
Press STOP to search list.
Press ESC to live mode.
12
Backup mode:
Before backup, USB pan driver is required. Back up file size can not exceed 1GB, when
system reads USB (thumb driver only) device 128MB USB, the system will stop recording
about 2 seconds. On live mode, press backup button to file backup page.
Total hard disk date & time range
Select start and end time of backup
After select backup time, apply to count
data size. After size appears, press backup
button to USB page.
13
DVR is reading pan driver
After a while, all backup information display on screen, user now can press backup button to
start file backup.
Data is writing to USB pan drive, users please wait until backup complete. Press menu button
to quit USB page.
USB compatible(Max. 4G)
ADATA / Transcend / San Disk / Kingston
14
Main Menu – System Set – RS-485
Main Menu – System Set – Pan/Tilt Device
Control: Keypad, mouse
* Mouse control: press ESC to PTZ mode, press AUTO button, and then once-click left button
of mouse to control PTZ movement.
Press quad button + number 1 ~ 4 button to set presets, press AUDIO + 1 ~ 4 to call preset.
Press AUTO to start auto presets, AUTO again to cancel.
Up/Down/Left/Right: PTZ dome direction control
+ / - : Zoom in / Zoom out
The AUTO command is 76 + Preset. The command would be different if connect to
others PTZ dome. It is normal if no any action after press AUTO.
This page is for control keyboard connection.
Please choose baud rate and ID. DVR
maximum amount ID is 16
Other settings just leave them as default
15
Net viewer
Viewer function:
1. Backup file player
2. Network viewer
3. Connection
DVR control via viewer:*
4. DVR screen: Split, Channel full screen / Key lock / Channel auto sequence.
Audio ON : stream speed – not good. OFF : stream speed – good
5. DVR function: MENU / ESC / Play / REC / T-SRH / - values change / + values change
6. DVR direction button: Up (Item select, Play Stop) / Down (Item select, Play Pause)
Left (Item select, Play Reverse) / Right (Item select, Play Forward)
ENT (ENTER): Item confirm/select, values change)
7. DVR menu pop-up
8. Audio volume (PC site)
*Viewer control panel button is same as DVR keypad.
*Viewer and DVR display is synchronously.
*PTZ control is supported on viewer and control way is same as DVR keypad.
*PTZ control and movement speed depends on network streaming.
•
‚ ƒ „ … † ‡ ˆ
16
IE browser:
IE control button is same as DVR keypad.
1. Before DVR IE connection, please download the NTVIEWER.exe to DVR hard disk from
CD-ROM, or you can download from server of internet and then you can view DVR image
via internet any PC.
Steps: CD disk à NTVIEWER.exe àUSB pan drive à DVR (with hard disk) USB à
Menu - System Set – Load Player Software à ENTER button
More details please check user’s manual of CD disk.
85-DM4062-A002-B
Loading...