Sharp ER-A770 User Manual [de]

KASSENTERMINAL

MODELL

ER-A770

BEDIENUNGSANLEITUNG

EINLEITUNG

Wir danken Ihnen, daß Sie sich für den Erwerb des SHARP POS-Kassenterminals, Modell ER-A770,
entschieden haben. Bitte lesen Sie diese Bedienungsanleitung vor Inbetriebnahme des Kassenterminals
sorgfältig durch, um in der Lage zu sein, das hochwertige System mit allen seinen Funktionen richtig und
problemlos bedienen zu können.

Diese Bedienungsanleitung sollte sorgfältig aufbewahrt werden, damit sie im Fall von Bedienungsproblemen
jederzeit griffbereit ist.

WICHTIG

• Als Aufstellplatz Ihres POS-Kassenterminals sollte eine Stelle gewählt werden, die keiner direkten

Sonneneinstrahlung, ungewöhnlichen Temperaturveränderungen, hoher Luftfeuchtigkeit oder
Wasserbeeinflussung ausgesetzt ist und dieses von Wärme- und Magnetquellen ferngehalten ist.

Das Aufstellen des Gerätes an solchen Plätzen könnte zu Beschädigungen des Gehäuses oder der
elektrischen Bauteile führen.

• Das POS-Kassenterminal sollte nicht von Personen mit nassen Händen bedient werden.
Es könnte Wasser in das Innere des Kassenterminals eindringen und zur Beschädigung der
elektronischen Bauteile führen.

• Keinen übermäßigen Druck auf das Display ausüben.

Keine scharfkantigen Objekte an das Display halten.
Der Bildschirm kann leicht beschädigt werden.

• Das POS-Kassenterminal darf nur mit einem trockenen und weichen Tuch gereinigt werden.

Aggressive Flüssigkeiten wie Benzin oder Farbverdünner dürfen niemals zur Reinigung verwendet
werden.

Die Verwendung von solchen Chemikalien führt zu Verfärbungen oder Beschädigungen des Gehäuses.

• Während der Benutzung kann das Display verschmiert werden bzw. verstauben.
In diesem Fall ist dieses mit einem weichen Tuch abzuwischen, welches zuvor in eine milde Seifenlösung
getaucht und gründlich ausgewrungen wurde.

• Das POS-Kassenterminal kann an jede normale Steckdose (offizielle (nominale) Netzspannung)

angeschlossen werden.

Beim Anschluß von anderen Elektrogeräten an den gleichen Stromkreis kann es zu Störungen im POS­Kassenterminal kommen.

• Setzen Sie sich bei einer Störung des POS-Kassenterminals bitte mit Ihrem Fachhändler in
Verbindung und versuchen Sie niemals das POS-Kassenterminal selbst zu reparieren.

VORSICHTSMASSNAHMEN

Dieses POS-Kassenterminal ist mit einer Speichersicherung ausgestattet, um bei einem eventuellen
Stromausfall die gespeicherten Informationen zu erhalten.

Wie im Allgemeinen bekannt ist, werden die dafür verwendeten Batterien auch bei Nichtbenutzung über
eine längere Zeitspanne entladen.
Um daher eine ausreichende Erstaufladung der Batterien zu gewährleisten und um einem möglichen
Verlust des Speicherinhalts nach der Aufstellung des POS-Kassenterminals vorzubeugen, wird empfohlen,
daß jedes einzelne Kassenterminal vor der Inbetriebnahme 24 bis 48 Stunden aufgeladen wird. Zum
Aufladen der Batterien muß das Kassenterminal an das Netz angeschlossen werden und der Netzschalter
auf “ON” stehen. Durch diese vorbeugende Batterieaufladung kann eine eventuelle Anforderung des
Kundendiensttechnikers vermieden werden.

1

2

INHALT

EINLEITUNG··················································································································································1
WICHTIG ·······················································································································································1
VORSICHTSMASSNAHMEN ························································································································1

1. Bezeichnung der Bauteile und Funktionen··························································································7

Außenansicht···········································································································································7

Vorderansicht ·································································································································7
Rückansicht····································································································································7
Neigungseinstellschrauben ············································································································8

Tastatur····················································································································································8

Anbringen der Tastaturfolie ············································································································8
Tastaturanordnung (Standardausführung) ·····················································································9

Optionale Tasten ··························································································································10
Bedienerschlüssel und -tasten···············································································································12
Display···················································································································································13

Bedieneranzeige···························································································································13

Bildschirmschoner-Modus ············································································································14

2. Vor der Inbetriebnahme des POS-Kassenterminals ·········································································15
Einstellung des Displays························································································································15
Anschluß von Druckern und Einsetzen der entsprechenden Papierrollen ············································15

3. Wahl der Betriebsart ····························································································································16
Betriebsarten ·········································································································································16
Wahl der Betriebsart······························································································································17

Wahl einer Betriebsart··················································································································17
Rückkehr zum Modus-Wahlfenster ······························································································17

4. Kassenbons··········································································································································18
Bontypen················································································································································18

Aufrechnungsbon ·························································································································18
Einzel-/Doppelbon ························································································································19
Aufrechnungsbon + Einzelbon······································································································20
Doppelter Aufrechnungsbon·········································································································20
Doppelter Aufrechnungsbon + Einzelbon·····················································································20

Sortierbonfunktion··································································································································21

5. Vor Registrierungen·····························································································································23
Vorbereitung für Registrierungen···········································································································23
Fehlermeldung·······································································································································23
Kassenbon-Druckbeispiel······················································································································23
Bedienerzuweisung ·······························································································································24
Postenwahl vom Menüfenster ···············································································································25
Registrierung des Wechselgeld-Anfangsbestands················································································27

6. Registrierungen ···································································································································28
Postenregistrierungen····························································································································28

Einzelpostenregistrierungen·········································································································28
Wiederholungsregistrierungen······································································································31
Multiplikationsregistrierungen·······································································································32
Gebinderegistrierungen················································································································33
Einzelposten-Barverkauf (SICS)-Registrierungen/Einzelposten­Abschlußregistrierungen (SIF)······································································································34
Waagenregistrierungen ················································································································35
Umsatzneutrale Verkaufsvorgänge ······························································································37

Spezielle PLU-Registrierungen··············································································································38

Werbeverkaufsfunktion (Normalverkauf)······················································································38
Werbeverkaufsfunktion (Menüverkauf)·························································································39
Haupt-PLU-Registrierungen ·········································································································40
Combo-Menü-Registrierungen ·····································································································40

Mit-/Ohne-Funktion·······················································································································41
Umschaltung der PLU-Ebene (für Direkt-PLUs)···········································································42
Umschaltung der PLU-Preisebenen·····························································································44
Condiment-Menü-PLU-Registrierungen ·······················································································45
Happy Hour ··································································································································47
Spartenwechsel····························································································································48
Pint-Registrierungen·····················································································································49

Anzeige der Zwischensummen··············································································································50

Zwischensumme···························································································································50
Differenz-Zwischensumme (Differ ST) ·························································································50

Abschluß einer Transaktion···················································································································51

Bar- oder Scheckzahlung ·············································································································51
Gemischte Zahlung (Bar + Scheck)······························································································52
Bar- oder Scheckverkauf, der keine Zahlgeldregistrierung erforderlich macht·····························52
Kreditverkauf ································································································································53
Gemischter Zahlgeldverkauf (Bargeld oder Scheck + Kredit) ······················································53

Berechnung der MWSt/Steuer···············································································································54

MWSt/Steuer-System···················································································································54
Registrierungen von MWSt-Wechsel····························································································55

Tischspeicher-Registrierungen (GLU/PBLU)·························································································56

GLU/PBLU-System·······················································································································56
DRIVE THRU-Funktion·················································································································59
Anzahlungsregistrierungen (Deposit) ···························································································63
Freigabe und Übernahme von Tischen ························································································64
Rechnungsdruck···························································································································65
GLU-Zwischenabruf (nur für das GLU-System) ···········································································66
Rechnungszusammenlegung/Rechnungsumbuchung·································································66
Rechnungsseparierung ················································································································68
Tischöffnung am Ende einer Transaktion·····················································································70
Hotelumbuchung ··························································································································70

Unterschiedliche Registrierungen··········································································································71

Prozentberechnungen (Aufschlag oder Abschlag)·······································································71
Abschlagsregistrierungen·············································································································72
Retourenregistrierung···················································································································73
Rückgaberegistrierung ·················································································································73
Ausdrucken von nichtaddierenden Codenummern ······································································74
Ausdrucken von Zusatztext ··········································································································74
Rechnung mit Bewirtungsbeleg····································································································75

Zahlungshandhabung····························································································································76

Registrierung von Trinkgeld··········································································································76
Fremdwährungsumrechnung········································································································77
Registrierungen für bezahlte Rechnungen···················································································78
Ausgabenregistrierungen ·············································································································79
Kein Verkauf (Geldwechsel)·········································································································80
Zahlungsumbuchung····················································································································80
Scheckeinlösung ··························································································································81
Bedienungsgeld····························································································································82

VIP-Funktion·································································································································82
Schwund-Modus····································································································································83
Angestelltenfunktion ······························································································································84

Anmeldung von Bediener/Manager······························································································84

Aufzeichnung der Arbeitszeit für Angestellte················································································84
SCHULUNGS-Betriebsart······················································································································86
Oberkellner············································································································································87
Überlappende Bedienerregistrierung·····································································································88

7. Korrekturen···········································································································································89
Korrektur der letzten Registrierung (Sofortstorno)·················································································89
Korrektur der vorletzten bzw. früheren Registrierungen (indirekter Storno)··········································90
Zwischensummenstorno························································································································91
Korrektur von falschen Registrierungen, die nicht durch die Sofort-, indirekte oder
Zwischensummen-Stornofunktion verarbeitet werden können······························································91

3

8. Unterschiedliche Druckfunktionen·····································································································92

Nachträgliche Bonausgabe····················································································································92
Proformarechnung·································································································································93
Quittungsdruckfunktion··························································································································93

9. Managerfunktion···································································································································94
Aktivierung des Managermodus············································································································94
Überschreibungsregistrierungen············································································································94
Trinkgeldregistrierungen························································································································95
Rechnungsspeicherung/Rechnungsaufhebung·····················································································95

10. Korrektur nach Abschluß einer Transaktion ·····················································································96

11. Abruf (X) und Nullstellung (Z) von Umsätzen····················································································97

Erstellung eines X1/Z1- oder X2/Z2-Umsatzberichts ···································································97

Tägliche Gesamtumsätze····················································································································100

Allgemeiner Umsatzbericht (Gesamt-Umsatzbericht) ································································100
Spartenbericht ····························································································································103
Einzelgruppenbericht für Sparten·······························································································103
Gesamtgruppenbericht für Sparten ····························································································103
PLU-Bericht für einen festgelegten Bereich ···············································································104
Combo-Menü-Verkaufsbericht····································································································105
PLU-Bericht für zugewiesene Sparte ·························································································106
Einzelgruppenbericht für PLUs···································································································107
Gesamtgruppenbericht für PLUs································································································107
PLU-Bestandsbericht··················································································································107
PLU-Kostenbericht ·····················································································································108
PLU “Top 20”-Bericht··················································································································109
PLU-Gesamt-Nichtumsatzbericht·······························································································110
PLU-Nichtumsatzbericht pro Sparte···························································································110
PLU-Mindestbestandsbericht ·····································································································110
Stündlicher PLU-Gesamtgruppenbericht····················································································111
Gesamtkassenbestandsbericht ··································································································111
Transaktionsbericht ····················································································································111
Provisionsumsatzbericht·············································································································112
Mehrwertsteuerbericht················································································································112
Chefbericht ·································································································································112
Gesamt-Bedienerbericht·············································································································113
Einzelbedienerbericht·················································································································114
Bedienerbericht (Fehlbedienung des Getränkeautomaten)························································116
Getränkeautomat-Fehlerabrufbericht ·························································································116
Getränkeautomat-Rückstellungsbericht ·····················································································116
Aktivstatusbericht für Angestellte ·······························································································117
DRIVE THRU-Bedienungszeitbericht·························································································117
Stündlicher Bericht ·····················································································································117
Personalkostenbericht (%) ·········································································································118
Zutaten-Bestandsbericht ············································································································118
GLU-/PBLU-Bericht ····················································································································118
GLU-/PBLU-Bericht pro Bediener·······························································································119
DRIVE THRU-Verkaufsbericht ···································································································119
DRIVE THRU-Verkaufsbericht pro Bediener··············································································120
Saldenbericht······························································································································120
Rechnungsbericht·······················································································································120
X1/Z1-Kettenberichte··················································································································120

Periodische Umsatzberichte················································································································121

Allgemeine Information···············································································································121
Angestelltenbericht·····················································································································122
Überstundenbericht ····················································································································122
Bericht über Angestellten-Arbeitszeitangleichung······································································123
Täglicher Nettoumsatzbericht·····································································································123
X2/Z2-Kettenberichte··················································································································123

Zwangsweise Kassen-Ist-Eingabe (CCD) ···························································································124

4

12. Verwendung der Tastaturfolie···········································································································126

Tastenanordnung der programmierbaren Tastatur··············································································126
Programmierung von alphanumerischen Zeichen···············································································127

Verwendung der Zeichentasten auf der Tastatur ·······································································127
Eingabe von Zeichencodes ········································································································128

13. Programmierung·································································································································129
Allgemeine Anleitungsschritte··············································································································129

Programmierbeispiel···················································································································129

Programmierung von Artikeln··············································································································131

Sparte·········································································································································132
PLU·············································································································································134
PLU-Bereich ·······························································································································137
PLU-Bestand ······························································································································138
Zutaten ·······································································································································139
Zutatenbestand···························································································································140
PLU-Menütaste···························································································································141
Combo-Menü (Combo-PLU)·······································································································142
Haupt-PLU-Tabelle·····················································································································143
Condiment-Menü-PLU-Tabelle···································································································144
Werbeverkauf-Tabelle (normaler Verkauf) ·················································································146
Werbeverkauf-Tabelle (Menü-Verkauf) ······················································································147
Rezepturtabelle ··························································································································148
Waagentabelle····························································································································149
Spartenumschaltung···················································································································150
Happy Hour ································································································································150

Programmierung der Direkteingabetasten···························································································151

Direkteingabetaste······················································································································151

Funktionelle Programmierung··············································································································152

Rabattaste (

!

bis ()··············································································································153

Prozenttaste (

¡

bis ª)···········································································································154
Provision·····································································································································154
Bedienungszuschlag ··················································································································155
Trinkgeld·····································································································································155
Anzahlung···································································································································156
Bezahlte Rechnung (RA)············································································································156
Ausgaben (PO)···························································································································157

Programmierung der Funktionstasten ·································································································158

Bargeldtaste ·······························································································································159
Schecktaste (

h

bis Ò) ···········································································································160

Kredittaste (

Ó

bis Œ)··············································································································161
Hotelumbuchungstaste···············································································································162
Bargeldbestand ··························································································································163
Rückgeld auf Scheckzahlung ·····································································································163
Scheckeinlösung ························································································································164

Programmierung der Währungen········································································································165

Fremdwährungstaste (

,

bis +)·····························································································165

Schublade für Fremdwährung ····································································································165

Textprogrammierung ···························································································································166

Funktionstext ······························································································································167
Spartengruppentext····················································································································170
PLU-Gruppen-Text ·····················································································································170
Stunden-PLU-Gruppen-Text·······································································································171

Personal-Programmierung···················································································································172

Bediener ·····································································································································173
Manager ·····································································································································175
Angestellte··································································································································176
Arbeitsplatztabelle ······················································································································177

POS-Kassenterminal-Programmierung·······························································································178
Einstellung von Datum und Uhrzeit ·····································································································179

Datum/Uhrzeit·····························································································································179

5

Wahl von Zusatzfunktionen ·················································································································180

Funktionsunterdrückung·············································································································181
Funktionswahl·····························································································································182
Druckauswahl·····························································································································184

Programmierung von Berichten···········································································································187

Nullunterdrückung ······················································································································188
Allgemeines Berichtsformat········································································································189
Stündlicher Bericht ·····················································································································189
Kettenbericht ······························································································································190

Mitteilungstextprogrammierung ···········································································································193

Kassenbonlogo···························································································································194
Zusatztext···································································································································194
Quittungsdrucktext······················································································································195
Belegtext·····································································································································195
Beleg-Fußzeilentext····················································································································195
Mitteilung auf Bewirtungsbeleg···································································································196
Name des Zahlungsempfängers ································································································196

Programmierung der Gerätekonfiguration···························································································197

Journaldrucker····························································································································198
Bondrucker ·································································································································198
Belegdrucker ······························································································································199
Berichtsdrucker···························································································································200
Externer Drucker (KP#1 bis KP#9)·····························································································200
Waage/Getränkeautomat/Online································································································201

Programmierung des DRIVE THRU-Codes·························································································202

DRIVE THRU-Code····················································································································202

Programmierung des Zimmer-GLU-Codes··························································································203

Zimmer-GLU-Code·····················································································································203
MWSt-Programmierung·······················································································································204
Programmierung für das Senden der Sicherungsdaten ······································································205

Senden des Sicherungsdaten ····································································································205
Programmierung für das Empfangen der Sicherungsdaten ································································206

Empfangen der Sicherungsdaten·······························································································206
Getränkeautomat-Programmierung·····································································································207

Getränkeautomat-Vorbelegung ··································································································208

Getränkeautomat-Bediener ········································································································209

Herunterladen·····························································································································209
Online-Konfigurations-Programmierung······························································································210
Programmierung für den PRICE-Modus······························································································211
Programmierung der Automatik-Sequenztasten··················································································212
Abruf gespeicherter Programme··········································································································213

Programm-Abrufsequenz ···········································································································213

Druckbeispiel······························································································································215

14. Getränkeautomat································································································································229
Getränkeautomat-Fehlbedienung und Fehlbedienungsdatei ·····················································230
Ursachen für Getränkeautomat-Fehlbedienung ·········································································230
Aufhebung der Fehlbedienung ···································································································231
Abruf der Fehlbedienungsdatei ··································································································231
Korrektur von Getränkeautomat-Artikeln in der Getränkeautomat-Fehlbedienungsdatei···········232

15. Elektronisches Journal/Datenlöschung···························································································233
Elektronisches Journal ···············································································································233
Löschen der Daten ·····················································································································233

16. EURO-Funktion···································································································································234

17. Wartung durch den Bediener············································································································236

Ersetzen der Speicherschutzbatterie···································································································236
Verhalten bei Stromausfall···················································································································238
Bevor Sie den Kundendiensttechniker anfordern················································································238

18. Sonderzubehör···································································································································239

Liste des Sonderzubehörs···················································································································239

19. Technische Daten·······························································································································240

6

Rückansicht

Bezeichnung der Bauteile und
Funktionen

Dieses Kapitel beschreibt die Bauteile und Funktionen dieses POS-Kassenterminals.

Außenansicht

Vorderansicht

1

7

Bedieneranzeige

Tastatur

Netzschalter

Sicherstellen, daß
der Netzschalter auf
OFF steht, bevor das
Netzkabel
eingesteckt wird.

Bedienerschloß

Linke Seite des
Kassenterminals

Schalterdeckel

Helligkeits­regler

Kontrastregler

Netzschalter

Hintere
Abdeckung

1. Die äußere Schraube lockern.

2. Die Höhe der inneren Schraube
einstellen.

3.Die äußere Schraube fest anziehen.

Tastatur

Anbringen der Tastaturfolie

Die Tastaturfolie zwischen der Tastaturabdeckung und dem Gehäuse einlegen (siehe Abbildung), dann die
Klauen am Oberteil der Tastaturabdeckung in die Schlitze des Gehäuses hineindrücken.

• Die Tastaturfolie nicht zu straff spannen.
Die Abdeckung kann dadurch reißen.

• Die Tastaturfolie durch eine neue
ersetzen, falls sie naß werden sollte. Die
Benutzung einer nassen Folie über
einen zu langen Zeitraum, kann zu
Störungen des Kassenterminals führen.

• Unbedingt die von SHARP bestimmten
Tastaturfolien verwenden. Zu dicke oder
zu harte Folien erschweren eine
einfache Tastenbedienung. Im
schlimmsten Fall wird eine
Tasteneingabe unmöglich.

• Die Tastaturfolie gut unter der
Tastaturabdeckung glattstreichen, so
daß keine Falten verbleiben. Nur so
kann eine einfache Tastenbedienung
gewährleistet werden.

• Wenn Sie eine neue Tastaturfolie benötigen, fragen Sie bitte Ihren autorisierten SHARP-Händler.

• Die Tastaturabdeckung verschleißt mit der Zeit. Wenn die Tastaturabdeckung verschmutzt ist oder Risse
aufweist, ist sie durch eine neue zu ersetzen. Nähere Auskünfte erfahren Sie bei Ihrem autorisierten
SHARP-Händler.

HINWEIS

8

Neigungseinstellschrauben

Diese Linien dienen zur Höhenmessung der Schraube.

Tastaturfolie

Tastatur­abdeckung

Gehäuse

Tastaturanordnung (Standardausführung)

Wenn Sie den Wunsch haben, die Tastenanordnung zu ändern, sprechen Sie bitte mit Ihrem autorisierten
SHARP-Händler.

HINWEIS

9

Zehnertasten

Dezimalpunkttaste

Gesamtlöschtaste

Multiplikationstaste

Retourentaste

Stornotaste

PLU-/Sub-Spartentaste

“Mit”-Taste

“Ohne”-Taste

Zwischenabschlußtaste

Direkt-Texteingabetasten 1 bis 6

Preisebenenumschalttasten 1 bis 3

Rechnungstaste

MODE

TRANS

GC

RCPT

TEXT4TEXT5TEXT

TEXT1TEXT2TEXT

TRANS

OUT

IN

MISC

CANCEL

FUNC
PAGE

UP

•

789
456
123
000

SLIP

6

3

BS BT

ENTER

PAGE
DOWN

CL

000

AUTO

2

AUTO

1

GUEST

#

VOID

PRICE
SHIFT3

PRICE
SHIFT2

PRICE
SHIFT1

PLU/

SUB

CH

#

CR

#

ST TL

L1

L2

L3

VAT

SHIFT

RF

WITH

WITH

OUT

OPENED

GLU

GLU

NBAL

FINAL

12

24

11

23

10

22

9

21

8

20

7

19

6

18

5

17

4

16

3

15

2

14

1

13

36

48

60

72

84

96

35

47

59

71

83

95

34

46

58

70

82

94

33

45

57

69

81

93

32

44

56

68

80

92

31

43

55

67

79

91

30

42

54

66

78

90

29

41

53

65

77

89

28

40

52

64

76

88

27

39

51

63

75

87

26

38

50

62

74

86

25

37

49

61

73

85

0

9

PLU/
SUB

00 000

•

CL

RF

VOID

WITH

WITH

OUT

FINAL

TEXT

1

PRICE

SHIFT1

GC

RCPT

TEXT

6

PRICE

SHIFT3

Optionale Tasten

Die folgenden optionalen Tasten können anstatt der in der Abbildung der Tastaturanordnung gezeigten
Tasten zusätzlich aufgesetzt werden. Für nähere Einzelheiten sprechen Sie bitte mit Ihrem Fachhändler.

HINWEIS

1

10

Direkt-PLU-Tasten
PLU-Ebene-Umschalttasten 1

bis 3
Gastnummer-Eingabetaste
Auflistungstaste für offene

Tische
“Alter Tisch”-Taste

“Neuer Saldo”-Taste
Taste für unterschiedliche

Funktionen
Betriebsarten-Menütaste

Eingabetaste

MWSt-Status-Umschalttaste
Automatik-Sequenztasten 1 und

2
Kreditmenü-Taste

Scheckmenü-Taste

Transfer-Aus-Taste

Transfer-Ein-Taste

Belegdrucktaste

Rechnungsaufteilungstaste
Taste für Rechnungszusammen-

legung/-übertragung
Zwischensummentaste

Total-Taste

Seite-Auf/Ab-Tasten

Cursortasten (Pfeil für auf/ab/rechts/
links)

Annulierungstaste

Direkt-PLU-Tasten

Spartentasten

Text-Tasten 7 bis 40

Prozenttasten 1 bis 9

Rabattasten 1 bis 9

Kredittasten 1 bis 8

Bar-Gesamtbetragstaste 2
Fremdwährung-

Umrechnungstasten 1 bis 9
Tasten 1 und 2 für bezahlte

Rechnungen
Ausgabetasten 1 und 2

Automatik-Sequenztasten 3 bis
25

Schecktasten 1 bis 4

Betragseingabetaste
“Neuer Tisch”-Taste 2 (für DRIVE

THRU)
“Alter Tisch”-Taste 2 (für DRIVE

THRU)
MWSt-Taste

Trinkgeldtaste (Bargeld)

Trinkgeldtaste (kein Bargeld)

Taste für “Trinkgeld bezahlt”

1/2-Taste

“Nichtaddierender Code”-Taste

“Kein-Verkauf”-Taste

L1 L3

GUEST

#

OPENED

GLU

GLU

NBAL

MISC

FUNC

MODE

ENTER

VAT

SHIFT

AUTO

AUTO

1

CR

#

96

2

CH

#

TRANS

OUT

TRANS

IN

SLIP

BS

BT

ST

TL

PAGEUPPAGE

DOWN

CANCEL

97

135

1

99

TEXT

7

TEXT

40

%1 %9

-

1

-

9

CR1 CR8

CA2

EX1 EX9

RA1 RA2

AUTO

25

PO1 PO2

AUTO

3

CH1 CH4

AMT

DRV

NC

DRV
GLU

VAT

CASH

TIP

NON-CASH

TIP

TIP

PAID

1/2

#

NS

11

PRICE

SHIFT4

PRICE

SHIFT7

PLU

MENU01

PLU

MENU50

MGR

#

CLERK

#

OPEN
TARE

PERSON

#

IND.

PAYMENT

SBTL
VOID

RCP.

SW

SCALE

PINT

DEPO

(+)

DEPO

(–)

EMP

#

TEXT

#

TIME

IN

CLK

1

CLK

10

EX

#

DIFFER

ST

C.BILL

REPEAT

GC

COPY

VIP1

H.T.

RCP

SF

CHK

PRINT

RCPT

TIME
OUT

DEPT

SHIFT1

DEPT

SHIFT4

BREAK
IN/OUT

VP

RTN

WASTE

WAIT

RC-DR.

E.BILL

L4 L10

C_NEXT

D_DISP

RC-GLU

VIP3

P.SFT

#

S.SFT

Managercode-Eingabetaste

Bedienercode-Eingabetaste

Waage-Eingabetaste

Tara-Eingabetaste
Personennummer-

Eingabetaste
Einzelzahlungstaste

Kassenbonausdrucktaste

Kassenbon-Ein/Aus-Taste

Pint-Taste

Plus-Anzahlungstaste

Minus-Anzahlungstaste

Textnummertaste

Angestelltencode-Eingabetaste

Arbeitsbeginn-Taste

Zwischensummenstornotaste

Kassenbonumschalttaste

Arbeitsschluß-Taste
Pausenanfang/Pausenende-

Taste
Quittungsdrucktaste

Rückgabetaste

Spartenumschalttasten
1 bis 4

Differenz-Zwischensummentaste

Taste für aufgelaufene Rechnung

Proformarechnungstaste

Wiederholungstaste

Fremdwährungs-Umrechnungsmenütaste

VIP-Verkaufstasten 1 bis 3

Hotelumbuchungstaste

Bedienertasten 1 bis 10

Scheckdrucktaste

Preisebenenumschaltnummertaste

PLU-Ebene-Umschalttasten 4 bis 10

Preisebenenumschalttasten 4 bis 7

PLU-Menü-Tasten 1 bis 50

Schwundmodus-Taste

Wartemodus-Taste (für DRIVE THRU)

Zurückruftaste (für DRIVE THRU)

“Nächste Condiment-Tabelle”-Taste

DRIVE THRU-Menü-Taste

“Rechnung mit Bewirtungsbeleg”-Taste

Tischwiederaufruf-Taste

Sortiergruppenumschalttaste

12

Bedienerschlüssel und -tasten

Dieses POS-Kassenterminal ermöglicht dem Bediener die Verwendung der folgenden vier Bediener­Identifikationssysteme:

• Bedienerschlüssel (6 Standard-Bedienerschlüssel/max. 126 Bediener)

• Bedienercodeeingabe (max. 255 Bediener)

• Bedienertasten (max. 10 Bediener)

• WMF-Bedienerschlüssel (max. 127 Bediener)

Das Standard-POS-Kassenterminal wurde vor der Auslieferung für das Bedienerschlüsselsystem
programmiert. Wenn Sie das Bediener-Identifikationssystem ändern möchten, sprechen Sie bitte mit Ihrem
autorisierten SHARP-Händler.

Bedienerschlüssel (1, 2, 3, 4, 5 und 6)

Die Bediener werden durch die in das Bedienerschloß eingesteckten Schlüssel identifiziert. Einen der
Schlüssel 1 bis 6 in das Bedienerschloß einstecken.

Bedienercodeeingabe (1 bis 9999)

Jeden einzelnen Bedienercode durch das folgende Verfahren eingeben:

Bedienertasten

Durch diese Tasten werden die Bediener identifiziert. Eine dieser Tasten drücken.

WMF-Bedienerschlüssel

Einen der WMF-Bedienerschlüssel in das WMF-Bedienerschloß einstecken.

CLK

1

CLK

10

XXXX

Bedienercode

˚

13

Display

Dieses POS-Kassenterminal ist mit einer LCD-Bedieneranzeige ausgestattet.

Bedieneranzeige

Das Display kann für den besten Blickwinkel geneigt werden.

Nicht versuchen, das Display über die volle Öffnungsposition
hinaus zu öffnen.

• Anzeigebeispiel 1 (REG-Modus)

Preisebene-Umschaltanzeige (P1-P7) : Zeigt die augenblicklich gewählte Preisebene an (die Anzeige

wird bei Happy Hour umgekehrt).

PLU-Ebene-Umschaltanzeige (L01-L10) : Zeigt die augenblicklich gewählte PLU-Ebene an.
Kassenbon-Umschaltanzeige (r) : Zeigt den Kassenbon-Umschaltstatus an.
Anzeige “T-Log nahezu voll” () :( ) Erscheint, wenn der Speicher 80% belegt ist.

: ( ) Erscheint, wenn der Speicher 90% belegt ist.
: ( ) Erscheint, wenn der Speicher 95% belegt ist.

Bestands-Alarmanzeige ( ) : Erscheint, wenn der Bestand des eingegebenen PLUs Null

entspricht oder einen Negativwert aufweist.

Sparten-Umschaltstatusanzeige

(D1-D4)

: Zeigt den augenblicklich gewählten Sparten-Umschaltstatus

an.

Fenster: Im REG-Modus werden im Fenster die gerade eingegebenen Posten und

Zahlungsarten angezeigt.

Erhaltenes Zahlungsmittel

Numerische Eingabe: Eingabebeträge erscheinen an der Cursorposition.

Umsatzbetrag einschließlich MWSt

Modusbezeichnung

Bedienercode

Uhrzeit

HINWEIS

14

• Anzeigebeispiel 2 (PGM-Modus)

Bildschirmschoner-Modus

Wenn Sie Strom einsparen möchten oder die Lebensdauer des Bildschirms verlängern wollen, ist die
Bildschirmschoner-Funktion zu aktivieren. Durch diese Funktion wird die LCD-Hintergrundbeleuchtung
ausgeschaltet, wenn für einen längeren Zeitraum nicht auf das POS-Kassenterminal zugegriffen wird. Sie
können die Zeit programmieren, für die das POS-Kassenterminal den Normalstatus beibehalten soll (bei
dem die Hintergrundbeleuchtung aktiviert ist), bevor der Bildschirm in den Bildschirmschoner-Modus
umschaltet.
Um in den Normalstatus zurückzukehren, ist eine beliebige Taste zu betätigen.

Fenster:

Im PGM-Modus werden
programmierbare Posten
aufgelistet.

Modusanzeige für Zeichen doppelter Größe (W):

Erscheint, wenn der Doppelzeichenmodus
während der Textprogrammierung gewählt wurde.

Großbuchstaben-Anzeige (A/a):

Wenn [Caps Lock] während der
Textprogrammierung aktiviert ist,
erscheint “A” im Display. Bei
deaktivierter [Caps Lock]-Funktion
wird “a” angezeigt.

Bedienercode

Modusbezeichnung

Uhrzeit

MWSt-Status-Umschaltanzeige (V) : Erscheint, wenn der MWSt-Status gewechselt wird.
Elektronische-Mail-Anzeige (M) : Erscheint, wenn eine elektronische Post empfangen wird.
Anzeige “Elektr. Journal nahezu voll” () :( ) Erscheint, wenn der Speicher 80% belegt ist.

: ( ) Erscheint, wenn der Speicher 90% belegt ist.
: ( ) Erscheint, wenn der Speicher 95% belegt ist.

Anzeige für Kassenbon-Ein/Aus-Status (R) : Erscheint, wenn die Kassenbon-Ein/Aus-Funktion in den

“Aus”-Zustand schaltet.

Bargeldbestandsmarke (X) : Erscheint in der unteren rechten Ecke der Anzeige, wenn

das sich in der Schublade befindliche Bargeld dem
programmierten Grenzbetrag überschreitet. Der
Bargeldbestand wird für Erfassung des Bar­Gesamtkassensolls ermittelt.

Vor der Inbetriebnahme des
POS-Kassenterminals

Dieses Kapitel beschreibt die erforderlichen Schritte, die bei der erstmaligen Benutzung des POS­Kassenterminals durchzuführen sind.

Einstellung des Displays

Die Einstellung der Bildschirmhelligkeit und des Kontrasts kann mit den folgenden Reglern ausgeführt
werden.

Anschluß von Druckern und Einsetzen der entsprechenden Papierrollen

Vor der Inbetriebnahme des Kassenterminals müssen der Drucker angeschlossen und die Papierrollen
eingesetzt werden. Siehe hierfür die Bedienungsanleitung des Druckers.
Das ER-A770 läßt sich für eine Anzahl von im Handel erhältlichen Druckern konfigurieren. Für spezifische
Hinweise hinsichtlich der Handhabung und Pflege des Druckers nehmen Sie bitte auf die entsprechende
Bedienungsanleitung des Druckers Bezug.

• Helligkeitsregler

Beim Zurückdrehen des Reglers
wird das Display abgedunkelt.
Beim Aufdrehen hellt sich das
Display auf.

• Kontrastregler

Beim Zurückdrehen des Reglers
wird das Display abgedunkelt.
Beim Aufdrehen hellt sich das
Display auf.

2

Bei der Hintergrundbeleuchtung handelt es sich um ein Verschleißteil. Wenn sich die LCD-Anzeige nicht
länger einstellen läßt und dunkel wird, muß die Hintergrundbeleuchtung ausgewechselt werden. Für
nähere Einzelheiten sprechen Sie bitte mit Ihrem autorisierten SHARP-Händler.

15

16

REG-Modus

OPXZ-Modus

OFF-Modus

X1/Z1-Modus

Wahl der Betriebsart

Nach dem Einschalten des POS-Kassenterminals und dem Betätigen der mTaste erscheint
das Modus-Wahlfenster im Display und listet die vorhanden Betriebsarten auf (siehe
nachfolgende Abbildung).

Modus-Wahlfenster

Betriebsarten

Aus dem Modus-Wahlfenster kann jede Betriebsart außer REG angewählt werden. Ihr POS-Kassenterminal
unterstützt die folgenden 8 Betriebsarten:

3

Dieser Modus läßt die Registrierung unterschiedlicher Verkaufsinformationen zu.
Dieser Modus ist nicht im Modus-Wahlfenster aufgeführt. Um diesen Modus aus dem
Modus-Wahlfenster abzurufen, muß die

C

Taste betätigt werden.

Ermöglicht das Abrufen von X- oder Z-Bediener-Umsatzberichten. Dieser Modus
kann ebenso zur Eingabe der Arbeitszeiten von Angestellten eingesetzt werden.

Dieser Modus sperrt sämtliche Funktionen des POS-Kassenterminals. Bei der Wahl
dieser Betriebsart verschwindet das Modus-Wahlfenster. Durch Drücken jeder
beliebigen Taste wird das POS-Kassenterminal aktiviert.

Ermöglicht das Abrufen und die Nullstellung verschiedener Tagesumsätze.

X2/Z2-Modus

Ermöglicht das Abrufen und die Nullstellung der Wochen- und Monatsumsätze.

PGM1-Modus

PGM2-Modus

PRICE-Modus

AUTO KEY-Modus

Für die Programmierung jener Positionen, die häufigen Anderungen unterliegen (z.B.
Einzelpreise von Warengruppen oder PLUs und Prozentsätze).

Für unterschiedliche PGM1-Programmierungen jener Positionen, die nicht häufigen
Änderungen unterliegen (z.B. Datum, Uhrzeit und eine Anzahl von
Registrierkassenfunktionen).

Dieser Modus läßt die Programmierung der Einzelpreise von PLUs zu.

Dieser Modus läßt die Programmierung der Automatik-Sequenztasten zu.

17

Wahl der Betriebsart

Wahl einer Betriebsart

1.

Eine der beiden Möglichkeiten benutzen:

• Den Cursor mit den Tasten

·

oder °auf die

gewünschte Position bringen.

• Die gewünschte Wahlnummer mit einer der Zifferntasten
eingeben.

2.

Die eTaste drücken.

Wenn in den REG-Modus umgeschaltet werden soll, einfach die

C

Taste betätigen.

Rückkehr zum Modus-Wahlfenster

Um zum Modus-Wahlfenster zurückzukehren, ist das folgende
Verfahren anzuwenden:

1.

Die

m

oder

C

Taste drücken, während das Menüfenster

für den gewählten Modus angezeigt ist.

• Das Kassenterminal schaltet in den REG-Modus.

2.

DiemTaste drücken.

• Das Kassenterminal kehrt zum Modus-Wahlfenster zurück.

Verfahren

Verfahren

HINWEIS

Kassenbons

(für externe Drucker (KP#1-KP#9))

Bontypen

Sie können für jeden externen Drucker einen der folgenden 5 Bontypen wählen. Sie sind in den
Betriebsarten REG, MGR und VOID zugänglich. Als Vorgabewert ist der Aufrechnungsbon gewählt.

• Aufrechnungsbon

• Einzel-/Doppelbon

• Aufrechnungsbon + Einzelbon

• Doppelter Aufrechnungsbon

• Doppelter Aufrechnungsbon + Einzelbon

Der Positionendruckmodus für den Kassenbon läßt sich durch Drücken der Taste vor einer
Postenregistrierung umschalten (Kassenbon-Umschaltfunktion).

• Einzel-/Doppelbon → Aufrechnungsbon

Aufrechnungsbon

Der Aufrechnungsbon ist ein Standardtyp. Es können verschiedene Positionen auf einem Kassenbon
ausgedruckt werden.

18

4

Aufrechnungsbon

HINWEIS

RCP

SF

Einzel-/Doppelbon

Wenn dieser Bontyp gewählt wird:

• Es wird ein Bon ausgestellt und die Transaktion bei jeder neuen Registrierung abgeschlossen.

• Es wird ein Einzel- oder Doppelbon ausgestellt, abhängig von der PGM2-Programmierung für Sparten.

• Jede Verkaufstransaktion wird automatisch als Barverkauf abgewickelt.

• Posten, die als SICS (Einzelposten-Barverkauf) oder SIF (Einzelposten-Abschluß) spezifiziert sind, werden
als Einzelbontyp behandelt.

• Die PBLU-Registrierung ist zulässig.

19

Doppelbon Einzelbon

Perforation

Aufrechnungsbon + Einzelbon

Wenn dieser Bontyp gewählt wird:

• Ein Aufrechnungsbon und entsprechende Einzelbons werden in Serie ausgestellt, wenn Sie die
Transaktion abschließen.

• Am Ende des Aufrechnungsbons wird die entsprechende Fußzeile ausgedruckt, wenn diese programmiert
ist.

• “Alte Saldo-Bons” sowie der Gesamtbon werden bei einer PBLU-Registrierung nicht ausgestellt.

• Multiplikationsregistrierungen werden auf den Einzelbons ausgedruckt.

• Nur die Kopfzeile wird auf jedem Einzelbon ausgedruckt.

Doppelter Aufrechnungsbon

Der Inhalt dieses Bontyps ist gleich wie beim Aufrechnungsbon.
Der Bon wird dabei jedoch zweimal ausgestellt.

Doppelter Aufrechnungsbon + Einzelbon

Der Inhalt dieses Bontyps ist gleich wie beim Aufrechnungs- und Einzelbon.
Der Bon wird dabei jedoch zweimal ausgestellt.

Perforation

Aufrechnungsbon

Einzelbon

Einzelbon

20

21

Sortierbonfunktion

Wenn die Sortierbonfunktion für Ihr POS-Kassenterminal programmiert wurde, werden die in der PLU­Gruppe befindlichen PLUs in sortierter Form ausgedruckt, wobei die Reihenfolge der eingegebenen Posten
keine Rolle spielt.

Die Sorten-Gruppennummer wird durch Drücken der Taste (Sorten-Umschalttaste) vorübergehend
umgeschaltet.

→ n →→{PLU-Registrierung} n: Gruppennummer (00 - 99)

Es wird angenommen, daß Sie die Posten in der folgenden Reihenfolge eingeben:

Das Druckformat unterscheidet sich je nach programmiertem Kassenbontyp wie folgt:

• Aufrechnungsbon

LOGO
Kopfzeile

GRUPPE1 TEXT
PL000002
PL000004

LOGO
Kopfzeile

PL000001

LOGO
Kopfzeile

GRUPPE0 TEXT
PL000001
GRUPPE1 TEXT
PL000002
PL000004
GRUPPE2 TEXT
PL000003

BAR

LOGO
Kopfzeile

GRUPPE2 TEXT
PL000003

Dieser Posten
wird unmittelbar
nach der
Eingabe des
PLUs der
Gruppennummer
00 oder der Sparte
ausgedruckt.

Diese Posten
werden aus­gedruckt, wenn
die Transaktion
abgeschlossen
ist.

Diese Posten
werden ausge­druckt, wenn
nach der Tran­saktion die
oder Taste
betätigt wird.

Einzel- oder Doppelbon

GC

RCPT

RCPT

GRUPPE0 TEXT

Beispiel

S.SFT

S.SFT

HINWEIS

2 P

c

Gruppe 0
Gruppe 1
Gruppe 2
Gruppe 1

1

3
4

Tastenbedienung

22

• Aufrechnungsbon + Einzelbon

LOGO
Kopfzeile

GRUPPE0 TEXT
PL000001
GRUPPE1 TEXT
PL000002
PL000004
GRUPPE2 TEXT
PL000003

BAR

LOGO
Kopfzeile

LOGO
Kopfzeile

GRUPPE1 TEXT
PL000002
PL000004

PL000001

Dieser Posten
wird unmittelbar
nach der Eingabe
des PLUs der
Gruppennummer
00 oder der Sparte
ausgedruckt.

Diese Posten
werden ausgedruckt,
wenn die Transaktion
abgeschlossen ist.

Diese Posten werden
ausgedruckt, wenn
nach der Transaktion
die oder Taste
betätigt wird.

Doppelbon

GC

RCPT

RCPT

GRUPPE0 TEXT

LOGO
Kopfzeile

GRUPPE2 TEXT
PL000003

LOGO
Kopfzeile

PL000003

LOGO
Kopfzeile

PL000004

LOGO
Kopfzeile

PL000002

Einzelbon

23

Vor Registrierungen

Vorbereitung für Registrierungen

1. Den REG-Modus mit der

C

Taste wählen.

2. Sicherstellen, daß alle Drucker im Systemverbund vor der Inbetriebnahme mit vollen Papierrollen

bestückt sind. Für zusätzliche Information beziehen Sie sich bitte auf die betreffende
Bedienungsanleitung des Druckers.

Fehlermeldung

In den folgenden Fällen tritt in Ihrem POS-Kassenterminal ein Fehlerzustand ein, wobei ein Piepton ertönt
und eine Fehlermeldung im Display angezeigt wird. Die Fehlermeldung durch Drücken der

L

Taste

löschen und den richtigen Schritt durchführen.

• Wenn eine Zahl eingegeben wird, die 32 Stellen übersteigt (Eingabestellen-Überlauf):
Den Fehler löschen und die korrekte Zahl eingeben.

• Wenn ein Tasteneingabefehler begangen wird:
Den Fehler löschen und die Tasten erneut richtig bedienen.

• Wenn eine Eingabe vorgenommen wird, die außerhalb der programmierten Eingabebegrenzung liegt:
Überprüfen, ob der Eingabebetrag korrekt ist. Wenn er korrekt ist, kann er in der MGR-Betriebsart
registriert werden. Rufen Sie Ihren Manager.

• Wenn die ermittelte Zwischensumme acht Stellen überschreitet:
Die Zwischensumme mit der

L

Taste löschen und eine Zahlungstaste drücken, um die

Transaktion abzuschließen.

Kassenbon-Druckbeispiel

5

Uhrzeit

Datum

Kassenterminalnummer
Bedienercode

Gesamtumsatz

Laufende Nummer

Posteneingabe

Barzahlung
Wechselgeld

Bedienername

REG-MODUS
OPXZ-MODUS

24

Bedienerzuweisung

Bediener lassen sich durch vier Systeme zuweisen: Bedienerschlüssel-, Bedienercodeeingabe-,
Bedienertasten- und WMF-Bedienerschlüsselsystem. Über die Wahl dieser Systeme gibt Ihnen Ihr SHARP­Händler gerne Auskunft.

Bedienerschlüsselsystem (Werkseinstellung)

Wenn Sie dieses System wählen, können die Bediener durch Einstecken des Bedienerschlüssels
zugewiesen werden. Ohne eingestecktem Bedienerschlüssel lassen sich keine Registrierungen
durchführen.

Bedienercodeeingabesystem

Wenn dieses System gewählt wird, können die Bediener zugewiesen werden, indem sie ihren Bedienercode
im voraus eingeben.

* Wenn die

˚

Taste gedrückt wird, erscheint das Fenster zur Eingabe des Geheimcodes.

Wenn die Postenregistrierung bei abgemeldetem Bediener durchgeführt wird, öffnet sich im Fenster das
Bediener-Eingabefeld und die Eingabe durch den Bediener wird erzwungen.

Die Abmeldung läßt sich durch das folgende Verfahren im REG- und MGR-Modus ausführen:

Abmeldung eines Bedieners:

˚

Bedienertastensystem

Wenn dieses System gewählt wird, können die Bediener durch Betätigen der entsprechenden
Bedienertasten auf der Tastatur angemeldet werden.

WMF-Bedienerschlüsselsystem

Wenn dieses System gewählt wird, können die Bediener durch Einstecken des WMF-Bedienerschlüssels
zugewiesen werden.

Wenn sich ein anderer Bediener anmeldet, wird der vorherige Bediener automatisch abgemeldet.

HINWEIS

XXXX

Bedienercode

˚

e

XXXX

Geheimcode

*

Verfahren

25

Postenwahl vom Menüfenster

Ihr POS-Kassenterminal ermöglicht es Ihnen, Funktionen aus einem Menüfenster anzuwählen.
Wenn Sie z.B. einen Posten Scheck 1-Verkauf eingeben möchten, wählen Sie die Option “CHECK1” vom
“CHECK”-Menü, anstatt die Taste

h

zu betätigen.

Jedes einzelne Menü kann wie folgt geöffnet werden:

• PLU-Menüfenster

• Verschiedenartiges Menüfenster

M

PLU

MENU01

PLU

MENU50

• Scheck-Menüfenster

Ç

• Kredit-Menüfenster

ç

• Fremdwährungs-Menüfenster

´

• Text-Menüfenster

TEXT

#

26

Verkauf eines PLU-Code 1-Artikels und Abschluß durch Scheck 1

1.

Die Taste drücken.

• Das PLU-Menüfenster erscheint.

2.

“PL000001” wählen.

3.

Die ÇTaste drücken.

• Das CHECK-Menüfenster erscheint.

4.

“CHECK” wählen.

5.

Den Betrag eingeben.

PLU

MENU01

Beispiel

27

Registrierung des Wechselgeld-Anfangsbestands

Wenn Sie den Barbetrag (Wechselgeldbetrag) vor Öffnung Ihres Geschäfts registrieren, können Sie diesen
Betrag von den Verkaufsumsätzen im Ausdruck der Umsatzberichte unterscheiden.
Ihr POS-Kassenterminal kann auf Registrierpflicht des anfänglichen Wechselgeldbetrags programmiert
werden. Fragen Sie bitte Ihren SHARP-Händler über nähere Einzelheiten.

Den OP X/Z-Modus wählen und einen Bedienerschlüssel einstecken. Danach ist die folgende Operation
auszuführen:

XXXXXXXX

Betrag

(max. 8 Stellen)

e

SCM(+) oder SCM(-) wählen

Verfahren

28

Registrierungen

Postenregistrierungen

Einzelpostenregistrierungen

Spartenregistrierungen

Einen Einzelpreis eingeben und eine Spartentaste drücken.
Wenn Sie einen programmierten Einzelpreis verwenden, nur eine Spartentaste drücken.

*Weniger als die programmierte obere Eingabe-Betragsgrenze

Wenn die Sparten eingegeben werden, denen ein Einzelpreis von 0 (Null) zugewiesen wurde, wird
ausschließlich die Umsatzmenge addiert.

HINWEIS

Beispiel

Bei Verwendung eines programmierten Einzelpreises

*Offener Preis
(max. 8 Stellen)

Spartentaste

Verfahren

Tastenbedienung

1200

6
7
c

Display

REG-MODUS

6

29

Direkt-PLU-Registrierungen (PLU-Registrierungen und Sub-Spartenregistrierungen)

Folgen Sie diesem Verfahren:

*Weniger als die programmierte obere Eingabe-Betragsgrenze

Auf PLU-Menü basierende Registrierungen (PLU-Registrierungen und Sub-Spartenregistrierungen)

Folgen Sie diesem Verfahren:

*

Weniger als die programmierte obere Eingabe-Betragsgrenze

Beispiel

Postenwahl vom
Menüfenster

bis

Bei Verwendung eines programmierten Einzelpreises

*Offener Preis

(für Sub-Spartenregistrierungen)

e

PLU

MENU50

PLU

MENU01

Verfahren

Beispiel

Direkt-PLU

Bei Verwendung eines programmierten Einzelpreises

*Offener Preis

(für Sub-Spartenregistrierungen)

e

Verfahren

Tastenbedienung

)

c

Display

Tastenbedienung

c

Display

PLU

MENU01

Den PLU-Code 15 im
Menüfenster wählen.