How it Works
Sharp
Loading...
ER-A460
Programming Manual
42 pgs510.38 Kb0
Service Manual
75 pgs3.75 Mb0

Sharp ER-A460, ER-A470 Programming Manual

Download
Page 1
PROGRAMMING MANUAL
CODE: 00ZERA460VPME
ELECTRONIC CASH REGISTER
MODEL ER-A460
MODEL ER-A470
(For "V" version) SRV KEY : LKGIM7113RCZZ PRINTER : DP-730
CHAPTER 1. SERVICE (SRV) MODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
CHAPTER 2. PROGRAM (PGM2/PGM1) MODE . . . . . . . . . . . . . . . . . . . . . . .14
CHAPTER 3. OP X/Z, X1/Z1, X2/Z2 MODE . . . . . . . . . . . . . . . . . . . . . . . . . . .41
The ER-A460/A470 has the Easy Programming function which allows the user to program easily. This function is not described in this manual. Please refer to the ER-A460/A470 EASY PROGRAMMING INSTRUCTION MANUAL of an accessory for the product.
CONTENTS
SHARP CORPORATION
This document has been published to be used for after sales service only. The contents are subject to change without notice.
ER-A460
ER-A470
Page 2
CHAPTER 1. SERVICE (SR V) MODE
The SRV key is used for operating in the SRV mode.
1. SRV. reset (Program Loop Reset)
Used to return the machine back to its operational state after a lock­up has occurred.
Procedure
• Method 1
1) Turn off the AC switch.
2) Set the mode switch to (SRV′) position.
3) Turn on the AC switch.
4) Turn to (SRV) position from (SRV′) position.
• Method 2
1) Set the mode switch to PGM2 position.
2) Turn off the AC switch.
3) While holding down JOURNAL FEED key and RECEIPT FEED key, turn on the AC switch.
Note: When disassembling and reassembling always power up
using method 1 only. Method 2 will not reset the CKDC6.
Note: SRV programming job#926-B must be set to "4" to allow PGM
program loop reset.
PRG. RESET ***
2. Master reset (All memory clear)
There are two possible methods to perform a master reset.
• MRS-1
Used to clear all memory contents and return machine back to its initial settings. return keyboard back to default. for default keyboard layout.
Procedure
1) Turn off the AC switch.
2) Set the MODE switch to the (SRV′) position.
3) Turn on the AC switch.
4) While holding down JOURNAL FEED key, turn to (SRV) position from (SRV′) position.
• MRS-2
Used to clear all memory and keyboard contents. This reset returns all programming back to defaults. The keyboard must be entered by hand. This reset is used if an application needs different keyboard layout other than that supplied by a normal MRS-1.
Procedure
1) Turn off the AC switch.
2) Set the MODE switch to the (SRV′) position.
3) Turn on the AC switch.
4) While holding down JOURNAL FEED key and RECEIPT FEED key, turn to (SRV) position from (SRV′) position.
5) Key position assignment:
* After the execution of MRS-2, only the RECEIPT FEED and
JOURNAL FEED keys can remain effective on key assignment. Any key can be assigned on any key position on the main key­board.
[key setup procedure]
MASTER RESET ***
NOTES: * 1: When the 0 key is pressed, the key of the key number on
display is disabled.
* 2: Push the key on the position to be assigned. With this, the key
of the key number on display is assigned to that key position.
Key number Key name Key number Key name
1 Numeric key "0" 9 Numeric key "8" 2 Numeric key "1" 10 Numeric key "9" 3 Numeric key "2" 11 Numeric key "00" 4 Numeric key "3" 13 Decimal point key 5 Numeric key "4" 14 CL key 6 Numeric key "5" 15 ⊗ key 7 Numeric key "6" 16 ST key 8 Numeric key "7" 17 TL key
3. Reading of the SRV mode program
List of program reports
JOB# Report name
900
SRV-mode program full item report (not incl. keyboard layout)
950
Keyboard layout report (on keys other than dept. keys and direct PLU keys)
951
Keyboard layout report (on dept. keys and direct PLU keys)
970 SRV file programming report
MRS-2 executed Key position set Free key
Disable
Free key setup complete.
*2
*1
0
0
– 1 –
Page 3
[JOB# 900]
All parameters contained for the SRV mode as listed Key operation.
900 → & → 3
STAMP Stamp
01/01/00 0:00 Date/Time 000000 # 0001   Machine No./Consecutive No.
#900 Job code
901# 0102 902# 0000
Contents of the SRV-mode programming
903# 4000 904# 0000 905# 0100 906# 0001
The contents of the programming are printed only on the journal individual formats shown at left. (No header is printed.)
907# 0014 908# 0000 909# 0000 910# 0004 911# 0000 912# 1141 913# 0002 914# 0100 915# 1020 916# 1000 917# 0000 918# 0000 919# 0000 920# 0000 921# 0000 922# 0000 923# 0000 924# 0000 925# 0000 926# 0000 927# 0000 928# 0000 929# 0000 980# 0000 930# z1 0000 Z1 reset counter 933# z1 0000 Hourly Z1 reset counter 934# z1 0000 PLU Z1/Z2 reset counter 935# z1 0000 Cashier Z1/Z2 reset counter 937# z2 0000 Z2 reset counter 939# z2 0000 Daily net Z2 reset counter
942# G T 2 *00000000000.00 GT2 943# G T 3 *00000000000.00 GT3
944# 0000 PGM2 mode secret code 945# 0000 Assignment Of RS232 channel 946# 0000 Assignment Of RS232 channel 948# 00 Training cashier No. 949# trai ning Training mode title
[JOB# 950]
The Key layout report is printed in SRV mode Key operation
950 → & → 3
STAMP Stamp
01/01/00 0:02 Date/Time 000000 # 0004 Machine No./Consecutive No.
#950 Job code
001 0 key 015 Key No./Key label/Location No. 002 1 key 016 003 2 key 024
004 3 key 032 005 4 key 017 006 5 key 025 007 6 key 033 008 7 key 018 009 8 key 026 010 9 key 034 011 00 key 023 012 000key 031
Key operation
951 → & → 3
STAMP Stamp
01/01/00 0:02 Date/Time 000000 # 0005 Machine No./Consecutive No.
#951 Job code
001 üüé 055 Key No./key label/Location No. 002 üüâ 056 003 üüä 057 004 üüà 058 005 üüå 059 006 üüç 060 007 üüê 061 008 üüë 062 009 üüè 063 010 üéü 064 011 üéé 065 012 üéâ 066 013 üéä 067 014 üéà 068 015 üéå 069 016 üéç 070 017 üéê 071 018 üéë 072
– 2 –
Page 4
[JOB#970]
Files on the memory are listed. Key operation
970 → & → 3
STAMP Stamp
01/01/00 0:03 Date/Time 000000 # 0007   Machine No./Consecutive No.
#970 Job code
*001* 0 0018 /0 0018 File table No./No. of records *002* 0 0018 /0 0018 /No. of used records *003* 0 0018 /0 0018 *005* 0 0018 /0 0018 *006* 0 0018 /0 0018 *007* 0 0200 /0 0020 *008* 0 0200 /0 0020 *009* 0 0200 /0 0020 *012* 0 0200 /0 0020 *014* 0 0005 /0 0000 *015* 0 0005 /0 0000 *016* 0 0069 /0 0069 *017* 0 0069 /0 0069 *018* 0 0069 /0 0069 *019* 0 0004 /0 0004 *020* 0 0004 /0 0004 *021* 0 0004 /0 0004 *022* 00045 004/00045 File table No./No. of records/No. of blocks/No. of used records *023* 00045 004/00045 *024* 00045 004/00045 *025* 0 0045 /0 0045 *026* 0 0045 /0 0045 *027* 0 0045 /0 0045 *028* 0 0045 /0 0045 *029* 0 0049 /0 0049 *030* 0 0049 /0 0049 *031* 0 0032 /0 0000 *032* 0 0032 /0 0000 *033* 0 0070 /0 0070
1dbf80 File memory start address 1dff68 Empty memory start address 1dffff Memory end address
[JOB#990]
Reading the Contents of the SRV-Mode Programming for SSP Key operation
990 → & → 3
STAMP Stamp
01/01/00 0:03 Date/Time 000000 # 0006   Machine No./Consecutive No.
#990 Job code
ssp era4 60v - 001 001 001 SSP No. 002 001 003 001 004 001 005 001 006 001 007 001
check sum er ror
– 3 –
Page 5
4. Service mo de programm ing
The following are the key operation required for programming.
Details of [A][B][C][D] will be discussed at each item description. ★ mark is MRS setting.
[JOB #901]:MRS=0102
#901-A: Not used (Fixed at "0") #901-B: Tax system
1. TAX system 901-B Auto TAX 1~3 0 Auto VAT 1~3 1 ★
Manual VAT 1~3 2
Manual VAT 1 3
Manual TAX 1~3 4
Swiss TAX 5
#901-C: 1. Rounding system
1. Rounding system 901-C Normal 0 ★
SWEDEN 1
DENMARK 4
#901-D: 1. TAB setting
1. TAB setting 901-D
0. 0
0.0 1
0.00 2 ★
0.000 3
[JOB#902] NOT USED MRS=0000
[JOB#903] MRS=4000
#903-A: 1. IR communication baud rate
1. Baud rate (bps) 903-A
2400 2 4800 3 9600 4 ★ 19200 5 38400 6 57600 7
115200 8
* The communication speed with the ER-02FD is 19200
bps.
#903-B, C, D: Not used (Fixed at "000")
[JOB#904] MRS=0000
#904-A: 1. Printing of date
1. Printing of date 904-A
★
Yes 0
No 4
#904-B: 1. Printing of consecutive No.
1. Printing of consecutive No. 904-B
★
Yes 0
No 4
#904-C, D: Not used (Fixed at "00")
[JOB#905] MRS=0100
#905-A: Not used (Fixed at "0") #905-B: 1. Tax printing when taxable subtotal is zero.
2. Tax printing when tax is zero.
1. Taxable subtotal is zero
2. Tax is zero 905-B
Skip
Print 0 Skip 1 ★
Print
Print 4 Skip 5
#905-C: 1. Printing of rounding amount in receipt. (For Australia)
2. Printing format for split pricing entry.
1. Printing of rounding amount in receipt
2. Printing format for split pricing entry
905-C
No
Normal format 0 ★
Australia format 1
Yes
Normal format 2
Australia format 3
#905-D : Not used (Fixed at "0")
[JOB#906] MRS=0001
#906-A: 1. Print Dept. and PLU number on receipt.
2. Entry which makes the PLU stock counter negative
1. Print Dept. and PLU number on receipt.
2. Entry w hich makes the PLU stock counter negative
906-A
No
Allowed unconditionally 0 ★
Operation allowed
despite ERROR
message
1
Inhibited 2
Yes
Allowed unconditionally 4
Operation allowed
despite ERROR
message
5
Inhibited 6
XXX
TL
(Job#)
[A] [B] [C] [D]
Numeric entry 4 digits max
0
– 4 –
Page 6
#906-B: 1. Bottle return function
2. Hash department setting
1. Bottle return function 2. Hash department setting
906-B
Disable
Disable 0 ★ Enable 2
Enable
Disable 4 Enable 6
#906-C: 1. Split pricing counting
2. Multiplication entry
1. Split pricing counting 2. Multiplication entry 906-C
Quantity
Multiplication 0 ★
Successive
multiplication
1
Split pricing 2
Package
Multiplication 4
Successive
multiplication
5
Split pricing 6
#906-D: 1. Presetting consecutive No.
2. Fractional quantity
1. Presetting
consecutive No.
2. Fractional quantity 906-D
Yes
No 0
Yes (3 digit decimal
place)
1 ★
No
No 2
Yes (3 digit decimal
place)
3
[JOB#907] MRS=0014
#907-A, B: Not used (Fixed at "00") #907-C: 1. In case of all cashier CCD and individual cashier CCD,
X1 report before CCD entry
2. Locking of REG mode entry after individual cashier re­setting
3. Minus department and PLU
1. In case of all cashier CCD and individual cashier CCD, X1 report before CCD entry
2. Locking of REG mode entry after individual cashier resetting
3. Minus department and PLU
907-C
Disable
No
Disable 0
Enable 1 ★
Yes
Disable 2
Enable 3
Enable
No
Disable 4
Enable 5
Yes
Disable 6
Enable 7
#907-D: 1. Z-counter print for PLU, Hourly, Cashier, Daily net
2. CCD compulsory
1. Z-counter print 2. CCD compulsory 907-D
Yes
Non compulsory 0
For individual cashier 1
For all cashier 2
No
Non compulsory 4 ★
For individual cashier 5
For all cashier 6
[JOB#908] MRS=0000
#908-A: GT print on Z report
GT1 (NET) GT2 (+) GT3 (–) 908-A
Print
Print
Print 0 ★ Skip 1
Skip
Print 2 Skip 3
Skip
Print
Print 4 Skip 5
Skip
Print 6 Skip 7
#908-B: GT print on X report
GT1 (NET) GT2 (+) GT3 (–) 908-B
Skip
Skip
Skip 0 ★ Print 1
Print
Skip 2 Print 3
Print
Skip
Skip 4 Print 5
Print
Skip 6 Print 7
#908-C: 1. Add void-mode transaction data to hourly total report
2. X1/Z1 report in X2/Z2 mode
3. Resetting of consecutive number in Z1 resetting
1. Add void-mode transaction to hourly total report
2. X1/Z1 report in X2/Z2 mode
3. Resetting of consecutive No.in Z1 resetting
908-C
No
Enable
No 0 ★
Yes 1
Disable
No 2
Yes 3
Yes
Enable
No 4
Yes 5
Disable
No 6
Yes 7
#908-D:
1. Printing X/Z report Journal only/Receipt & Journal (Except the individual cashier report)
2. Z1 resetting, resets GT Enable/Disable
1. Printing X/Z report 2. GT resetting at Z1 908-D
Receipt & Journal
Disable 0 ★ Enable 1
Journal
Disable 4 Enable 5
– 5 –
Page 7
[JOB#909] MRS=0000
#909-A: 1. Printing of training GT on the X report
2. Printing of training GT on the Z report
1. Printing of training GT on the X report
2. Printing of training GT on the Z report
909-A
Skip
Print 0 ★ Skip 1
Print
Print 2 Skip 3
#909-B: 1. Printing of data on PLU resetting report
2. All Z1 resetting in X1/Z1 mode
1. Printing of da ta on PLU resetting report
2. All Z1 resetting in X1/Z1 mode
909-B
Print
Enable 0 ★ Disable 2
Skip
Enable 4 Disable 6
#909-C: 1. Printing of data in void-mode totalizer and manager void
totalizer on Z2 report
2. Printing of data in void-mode totalizer and manager void totalizer on Z1 report
1. Void-mode totalizer on Z2 printing
2. Void-mod e tota liz er on Z1 printing
909-C
Print
Print 0 ★ Skip 2
Skip
Print 4 Skip 6
#909-D: Not used (Fixed at "0")
[JOB#910] MRS=0004
#910-A: 1. Over laped cashier function
2. Over laped cashier function 910-A No 0 ★
Yes 1
#910-B: 1. Auto cashier sign off at the end of each transaction
1. Auto cashier sign off at the end of each transaction
910-B
No (After cashier Z1 only) 0 ★
Yes (Everytime) 1
#910-C: Not used (Fixed at "0") #910-D: 1. Cashier system
1. Cashier system 910-D 1 hole 1 Cashier code entry 4 ★
[JOB#911] MRS=0000
#911-A: 1. Fraction treatment
1. Fraction treatment 911-A Round off 0 ★ Round up 1 Round down 2
#911-B, C, D: Not used (Fixed at "000")
[JOB#912] MRS=1141
#912-A: 1. Date print format
Date format 912-A Month/Day/Year 0 Day/Month/Year 1 ★ Year/Month/Day 2
#912-B: 1. Time system
1. Time system 912-B 12H 0 24H 1 ★
#912-C: 1. After transaction rec eipt format
2. Copy receipt
3. Footer print contr ol
1. After transaction receipt
2. Copy receipt
3. Footer print control 912-C
Total only
No
All receipt 0 On selected function
keys at the time of finalization
1
Yes
All receipt 2 On selected function
keys at the time of finalization
3
Detail
No
All receipt 4 ★ On selected function
keys at the time of finalization
5
Yes
All receipt 6 On selected function
keys at the time of finalization
7
#912-D: 1. Logo message control
1. Logo/stamp message control 912-D 3-line header instead of a stamp 0 Stamp only 1 ★ Stamp and 3-line footer 2 6-line header instead of a stamp 3 3-line header + 3-line footer 5
(Logo/stamp message format)
Header
Footer
Type : 0 532
STAMPSTAMP
1
– 6 –
Page 8
[JOB#913] MRS = 0002
#913-A: 1. VP format on Receipt/Journal
2. Content of TOTAL VP amount
1. VP format 2. VP amount 913-A
Date & amount
Total amount 0 ★ Tendered amount 1
Machine# & amount
Total amount 2 Tendered amount 3
#913-B: 1. Printing of [ST]
2. Escape the compulsion of VP
NOTE: Must turn to MGR mode and depress
• • , PRINT keys to escape validation
1. ST Print 3. Escape the compulsion of VP 913-B No
Disable 0 ★
Enable 1
Yes
Disable 4
Enable 5
#913-C: 1. Buzzer off 2sec. after lock error.
2. Buffered keyboard
1. Error beep 2. Buffered keyboard 913-C 2-sec. off
Yes 0 ★
No 1
Constant
Yes 2
No 3
#913-D: 1. Drawer closing compulsory
2. Error mode
3. Key catch sound
1. Drawer closing compulsory
2. Error mode 3. Key catch sound 913-D
Non-compulsory
All lock error
Enable 0
Disable 1
Miss operation (One shot error)
Enable 2 ★
Disable 3
Compulsory
All lock error
Enable 4
Disable 5
Miss operation (One shot error)
Enable 6
Disable 7
[JOB#914] MRS = 0100
#914-A: 1. Receipt issuing at no-sale
2. [NS] key separation from [TL] key for no sale function
1. Receip t issuing at no-sale
2. [NS] key separation 914-A
Enable
Yes 0 ★
No 2
Disable
Yes 4
No 6
#914-B: 1. No-sale after NON ADD code entry
1. No-sale after # entry 914-B Disable 0
Enable 1 ★
#914-C 1. Action to be taken when the machine is locked by the
Receipt/Journal paper near end check
2. Void mode
1. Action to be taken when the machine is locked by the Receipt/Journal paper near end check
2. Void mode
914-C
Unlocked by CL key
Enable 0 ★
Disable 2
Enforcing of paper roll replacement
Enable 4 Disable 6
#914-D: 1. CHECK CASHING Enable/Disable
1. CHECK CASHING 914-D Disable 0 ★
Enable 2
[JOB#915] MRS = 1020
#915-A: 1. Amount symbol
1. Amount symbol 915-A " $ " 0
" * "1★
" " 2
#915-B: Not used (Fixed at "0") #915-C: 1. Paper near end check
2. ST (–), ST (%) as many times needed/operation only once
1. Paper near end check
1. ST (–), ST (%) as many times needed/ operation only once
915-C
Yes
Unlimited 0 Once only 2 ★
No
Unlimited 4 Once only 6
#915-D: Not used (Fixed at "0")
– 7 –
Page 9
[JOB#916] MRS = 1000
#916-A: 1. Print format when text and amount overlaps each other
REG mode
1. Print format when text and amount overlaps each other REG mode
916-A
Truncate text 0
2 line print 1 ★
#916-B: 1. Finalization by charge (credit) when ST t 0
1. Finalization by (credit) when SBTL t 0 916-B
Disable 0 ★
Enable 4
#916-C: 1. Negative merchandis e subtotal
2. Subtotal entry compulsory before tendering
3. Subtotal entry before direct non-tendering finalization
1. Negative merchan­dise subtotal
2. Subtotal entry compulsory before tendering
3 .Subtotal
entry before direct non-tendering finalization
916-C
Allow
Noncompulsory
Non-compulsory 0 ★ Compulsory 1
Compulsory
Non-compulsory 2 Compulsory 3
Disallow
Non-compulsory
Non-compulsory 4 Compulsory 5
Compulsory
Non-compulsory 6 Compulsory 7
#916-D: 1. Coupon PLU printing on X/Z report
2. Net sales subtotal (NET1) printing on X/Z report
3. CHECK change total printing on X/Z report
1. Print coup on PLU’s on general report
2. Print net sales SBTL (NET1) on general report
3. Print CHK CHANGE on general report
916-D
Print
Print
Print 0 ★ Skip 1
Skip
Print 2 Skip 3
Skip
Print
Print 4 Skip 5
Skip
Print 6 Skip 7
[JOB#917] NOT USED: MRS = 0000
[JOB#918] MRS = 0000
#918-A: 1. Printing of text of a tied PLU in set PLU
2. Dirrect non-tendering finalization after previous tender entry
1. Printing of text of a tied PLU in promo PLU
2. Dirr ect non-te ndering finalization after previous tender entry
918-A
Yes
Disable 0 ★ Enable 2
No
Disable 4 Enable 6
#918-B: Not used (Fixed at "0") #918-C: 1. Printing Z1/Z2 counter in Z reports
1. Printing Z1/Z2 counter in Z reports 918-C Print 0 ★ Skip 4
#918-D: Not used (Fixed at "0")
[JOB#919] MRS = 0000
#919-A, B: Not used (Fixed at "00") #919-C: 1. Amount printing when PLU unit price is 0
1. Amount printing when PLU unit price is 0 919-C No 0 ★
Yes 1
919-D: 1. Conversion ST printing of native ST
1. Conversion SBTL print of native SBTL 919-D Yes 0 ★
No 4
[JOB#920] NOT USED MSR = 0000
[JOB#921] NOT USED MRS = 0000
[JOB#922] NOT USED MRS = 0000
[JOB#923] NOT USED MRS = 0000
[JOB#924] NOT USED MRS = 0000
[JOB#925] NOT USED MRS = 0000
[JOB#926] MRS = 0000
#926-A: Not used (Fixed at "0") #926-B: 1. Program reset at PGM 2 mode
1. Program reset at PGM2 mode 926-B
Disable 0 ★
Enable 4
#926-C, D: Not used (Fixed at "00")
– 8 –
Page 10
[JOB#927] MRS = 0000
#927-A: 1. Rounding up of the units digit of amount #927-B: 1. Rounding down of the units digit of amount
1. Rounding the units digit of amount 927-AB Common destination 00 ★
Netherland/Switzerland 82
Norway 54
#927-C: 1. Difference memory (Difference between before-
rounding and after-rounding)
2. Limit on the least sighificant digit in entering the amount on item
1. Difference memory 2. Limit on the least sighificant digit in entering the amount on item
927-C
No
Arbitary 0 ★
0 only 1
0 and 5 only 2
Yes
Arbitary 4
0 only 5
0 and 5 only 6
#927-D: 1. Application of rounding
2. Limit on the least significant digit in entering the amount of payment
1. Appl ication of rounding 2. Limit on the least significant digit in entering the amount of payment
927-D
Item & Payment
Arbitary 0 ★
0 only 1
0 and 5 only 2
Payment
Arbitary 4
0 only 5
0 and 5 only 6
[JOB#928] NOT USED: MRS = 0000
[JOB#929] NOT USED: MRS = 0000
[JOB#980] MRS = 0000
#918-A, B, C: Not used (Fixed at "000") #980-D: 1. Language selection of guidance message
1. Language selection of guidance message
910-D
English 0 ★
German 1
[JOB#930∼939] MRS = 0000
RESET REPORT COUNTER
JOB # Function
930 Z1 report counter 933 Hourly Z1 report counter 934 PLU Z1/Z2 report counter 935 Cashier Z1/Z2 report counter 937 Z2 report counter 939 31 day daily net Z2 report counter
[JOB#942, 943] MRS = 0000000000000
GT COUNTER PRESETTING
JOB # Function
942 GT2 (Positive GT) 943 GT3 (Negative GT)
Note: GT1 is obtained by calculation
Equation: GT1=GT2-GT3
[JOB#944] MRS = 0000
PGM1/2 secret code presetting
NOTE: When the secret code "0" is programmed, the secret code
entry is be inhibited.
[JOB#945] MRS = 0000
The assignment of RS232 channel by each devices * For use, the option control ROM (ER-A46R1) and the RS232 I/F
(ER-A5RS) are required.
#945-A: 1. Channel No. for online
1. Channel No. for online 945-A Channel No. 0 to 7
#945-B, C, D: Not used (Fixed at "000") * 0 = No connect
1 to 7 = Channel number
[JOB#946] NOT USED: MRS = 0000
[JOB#948] MRS = 000000
PROGRAMMING OF TRAINING CASHIER NO.
[JOB#949] MRS = "TRAINING"
THE TRAINING MODE’S TITLE
Characters can be entered by using alphabetic keys or numeric keys. Please refer to section 3.
[JOB#989]
RESETTING OF ALL COUNTER AND TOTALIZER
Job#
ABCD
Initial value of Z countr
"0000"
TL
Job#
0000000000000
13 digits
0
TL
944
XXXX
4 digits
0
TL
Job#
ABCD
0
TL
948
XX
TL
XX: Cashier No.
949
Character Key (8chra.)
Space
TL
989
TL
– 9 –
Page 11
[JOB#950] MRS = STANDARD KEY LAYOUT
Free key layout (Except for department keys and direct PLU keys.)
[JOB#951] MRS = STANDARD KEY LAYOUT
Free key layout (department keys and direct PLU keys)
• Programming of the keys to be dept keys or direct PLU keys on
the keyboard.
• Key No. is assigned to each key which is supposed to be dept.
Key or direct PLU key by depressing the key after entering the key No.
• Those keys programmed by this job No. will be dept. keys if dept.
code is assigned, and will be direct PLU keys if PLU code is assigned in the PGM2 mode.
FUNCTION KEY LIST
Key No. KEY KEY TEXT
1 0 KEY 0 KEY 2 1 KEY 1 KEY 3 2 KEY 2 KEY 4 3 KEY 3 KEY 5 4 KEY 4 KEY 6 5 KEY 5 KEY 7 6 KEY 6 KEY 8 7 KEY 7 KEY 9 8 KEY 8 KEY 10 9 KEY 9 KEY 11 00 KEY 00 KEY 12 000 KEY 000KEY 13 DECIMAL POINT . KEY 14 CLEAR CLEAR 15 ⊗ ✕ 16 ST SBTL 17 TL TOTAL 18 # # 19 NO SALE NS 20 PLU PLU 21 G. C. COPY GCCOPY 22 Level1 L1 23 Level2 L2 24 Level3 L3 25 PRINT VP 26 RCPT RCPT 27 VOID VOID 28 REFUND RFND
Key No. KEY KEY TEXT
29 %1 %1 30 %2 %2 31 %3 %3 32 %4 %4 33 (–)1 (–)1 34 (–)2 (–)2 35 (–)3 (–)3 36 (–)4 (–)4 37 VAT VAT 38 AUTO AUTO 39 AUTO2 AUTO2 40 AUTO3 AUTO3 41 AUTO4 AUTO4 42 AUTO5 AUTO5 43 CASH2 CA2 44 CHECK1 CHECK1 45 CHECK2 CHECK2 46 CHECK3 CHECK3 47 CHECK4 CHECK4 48 CR1 CR1 49 CR2 CR2 50 CR3 CR3 51 CR4 CR4 52 CONV1 EX1 53 CONV2 EX2 54 CONV3 EX3 55 CONV4 EX4 59 RA RA 60 RA2 RA2 61 PO PO 62 PO2 PO2 63
1
⁄
2
1
⁄2 KEY
64 AMT AMT 65 VAT SHIFT VAT SF 66 CASHIER NO. CASH# 67 DIFFER ST DIF ST
ER-A460 KEY POSITION
R J 16 22 28 34 40 46 52 58 64 70 76 82
5 10152127333945515763697581 4 9 14 20 26 32 38 44 50 56 62 68 74 80 3 8 13 19 25 31 37 43 49 55 61 67 73 79 2 7 12 18 24 30 36 42 48 54 60 66 72 78 1 6 11 17 23 29 35 41 47 53 59 65 71 77
ER-A470 KEY POSITION
R J 22 30 38 46 54 62 70 78 86 94 102 110 118 7 1421293745536169778593101109117 6 1320283644526068768492100108116 5 121927354351596775839199107115 4 111826344250586674829098106114 3 101725334149576573818997105113 2 9 16 24 32 40 48 56 64 72 80 88 96 104 112 1 8 15 23 31 39 47 55 63 71 79 87 95 103 111
950 Free key
Key number automatic increment
Key number manual increment
Initial setting
XXX
Key No.
To inhibit
TL
951 Free keyXXX
Key No.
Key number automati c increment
Key number manual increment
To inhibit
TL
– 10 –
Page 12
[JOB#971]
SRV FILE PROGRAMMING. (File creation deletion and change of record count or block count)
Key operation
• Normal file
Group
No.
File name Type
* File table No.
(Create/Erase)
1
Dept.
1
01, 02, 03, 05,
37, 40, 42 2 Dept Text (8chra.) 0 03 3 Dept Text (12chra.) 0 04 4 PLU 1 07, 08, 09, 12 5 PLU Text (8chra.) 0 09 6 PLU Text (12chra.) 0 10 7 PLU stock 0 11 8 Link PLU 1 14 9 Set PLU 1 15
10
Cashier
1
19, 20, 21, 22,
23, 24, 34, 37,
38, 39 11
Cashier Dept
0
37, 38, 40, 41,
42, 43 12 Hourly 1 29, 30 13 Daily net 1 31, 32 14 Reg. buffer 1 33, 34 15 Overlapped cashier 0 34 16 Message Text 0 35 17 Guidance Text 0 36 18 Term Dept. 0 06 19 Term PLU 0 13 20 Term Transaction 0 18 21 Term Cashier 0 24 22 Term Cashier Dept 0 39 23 All of term file 0 06, 13, 18, 24, 39
Type = 0 ; Create/Erase only Type = 1 ; Create/Erase and Increase/decrease the number of
Records or blocks.
* : The files which are created or erased by the entry of group
No.
971
@/FOR
abc
File group No.
delete
XXXXX
Number of records
TL
– 11 –
Page 13
File table
Table
No.
File name
RECORD BLOCK
Label
size
Data
size
MRS Max. #1 MRS Max. #2 1 Dept. Preset 18 50 1 1 1 6 2 Price 18 50 (1) 1 1 0 3 3 Text (8chra.) 18 50 (1) 1 1 0 8 4 Text (12chara.) 0 50 (1) 0 1 0 12 5 Daily 18 50 (1) 1 1 0 9 6 Term 18 50 (1) 1 1 0 9 7 PLU Preset 200 *** 11 3 6 8 Price 200 *** (7) 1 1 0 3 9 Text (8chra.) 200 *** (7) 1 1 0 8 10 Text (12chra.) 0 *** (7) 0 1 0 12 11 Stock 0 *** (7) 0 1 0 4 12 Daily 200 *** (7) 1 1 0 9 13 Term 0 *** (7) 0 1 0 9 14 Link PLU 5 *** 11 315 15 Set PLU 5 *** 11 330 16 Transaction Label 69 69 1 1 2 0 17 Daily 69 69 (16) 1 1 0 8 18 Term 69 69 (16) 1 1 0 8 19 Cashier Preset 4 15 1 1 1 3 20 Flag 4 15 (19) 1 1 0 2 21 Text 4 15 (19) 1 1 0 8 22 Cashier transaction Label 45 45 4 15 (19) 2 0 23 Daily 45 45 (22) 4 15 (19) 0 8 24 Term 45 45 (22) 4 15 (19) 0 8 25 Reset Csr trns. Label 45 45 1 1 2 0 26 Daily 45 45 (25) 1 1 0 8 27 Total cashier (Buffer) Label 45 45 1 1 2 0 28 Total 45 45 (27) 1 1 0 8 29 Hourly Label 49 49 1 1 1 0 30 Daily 49 49 (29) 1 1 0 8 31 Daily net Label 32 32 1 1 3 0 32 Total 32 32 (30) 1 1 0 8 33 Reg. buffer 70 255 1 1 0 36 34 Over lapped Csr 0 255 0 15 (19) 0 36 35 Message Text 0 87 0 1 2 12 36 Guidance Text 0 132 0 1 2 12 37 Csr trns. Dept Label 0 50 0 15 (19) 1 0 38 Daily 0 50 (37) 0 15 (19) 0 9 39 Term 0 50 (37) 0 15 (19) 0 9 40 Reset Csr Dept trns. Label 0 50 0 1 1 0 41 Daily 0 50 (40) 0 1 0 9 42 Total Csr (Buffer) Dept Label 0 50 0 1 1 0 43 Total 0 50 (41) 0 1 0 9
(#1) : Same as the number of record of table no. N (#2) : Same as the number of block of table no. N
– 12 –
Page 14
[JOB#996, 998] IR data send/receive
(ECR↔ECR, ECR↔ER-02FD)
[JOB#996] IR data send
X : SSP = 0
• Send to ECR (IrDA) : IrDA
(Enable baud-rate : 115200bps,
57600bps, 38400bps, 19200bps, 9600bps, 4800bps, 2400bps)
• Send to ER-02FD + CE-IR2 (CE-IR4) : ASK
(Enable baud-rate : 19200bps)
• Send to ECR (ASK) : ASK
(Enable baud-rate : 57600bps, 38400bps,
19200bps, 9600bps, 4800bps, 2400bps)
[JOB#998] IR data receive
• Receive from ECR (IrDA) : IrDA
(Enable baud-rate : 11500bps, 57600bps,
38400bps, 19200bps, 9600bps, 4800bps, 2400bps)
• Receive from ER-02FD + CE-IR2 (CE-I R4) : ASK
(Enable baud-rate : 19200bps)
• Receive from ECR (ASK) : ASK
(Enable baud-rate : 57600bps, 38400bps,
19200bps, 9600bps, 4800bps, 2400bps)
996
All data
X
Send to ECR(IrDA)
Send to ER-02FD or ECR(ASK)
ST
TL
998
Receive from ECR(IrDA)
Receive from ER-02FD or ECR(ASK)
ST
TL
– 13 –
Page 15
CHAPTER 2. PROGRAM (PGM2/PGM1) MODE
1.Readi ng of the PG M mo de pr og r am
[JOB#1100]: DEPT reading
Key operation
STAMP Stamp
01/01/00 0:04 000000 # 0009  
#1100 *PGMâ* Job Code/Mode title
01-10 Start No. – End No. D 01 0.00 Dept. code/Taxable/Sign, Price dpt.ü é g 01 Text/Group No. 0000001 c ol17 Program (* 1) Commission Group/HALO D 02 0.00 dpt.ü â g 01 0000001 c ol17 D 03 0.00 dpt.ü ä g 01 0000001 c ol17 D 04 0.00 dpt.ü à g 01 0000001 c ol17 D 05 0.00 dpt.ü å g 01 0000001 c ol17 D 06 0.00 dpt.ü ç g 01 0000001 c ol17 D 07 0.00 dpt.ü ê g 01 0000001 c ol17 D 08 0.00 dpt.ü ë g 01 0000001 c ol17 D 09 0.00 dpt.ü è g 01
(* 1)PROGRAM: ABCDEFG
A: Printing on the cashier report Yes/No 1/0 B: Item vp compulsory/noncompulsory 1/0 C: (Not used) 0 D: (Not used) 0 E: SIF/SICS/Normal 2/1/0 F: (Not used) 0 G: Amount entry type
Open and preset/preset/open/inhibited 3/2/1/0
[JOB#1200]: PLU reading
Key operation
STAMP Stamp
01/01/00 0:05 000000 # 0011  
#1200 *PGMâ* Job Code/Mode title
000001-000005 Start No. – End No. P 000001(ü é ) /00 PLU code (Dept code)/(* 1)/Base q’ty
0.00 Taxable/Sign, Price pl000001 co Text/Commission Group 002 Program (*2)/Stock P 000002(ü é ) /00
0.00 pl000002 co 002 P 000003(ü é ) /00
0.00 pl000003 co 002 P 000004(ü é ) /00
0.00 pl000004 co 002
(* 1)NORMAL. LINK PLU. SET MENU
: NORMAL : L LINK PLU : S SET MENU
(* 2)PROGRAM: ABC
A: (Not used) 0 B: (Not used) 0 C: Amount entry type
Open and preset/preset/open /inhibited = 3/2/1/0 (PLU) (Sub-dept)
1100
XX
Start No.
XX
End No.
Single item
All
TL
1200
XXXX
Start No. End No.
Single item
XXXX
All
TL
– 14 –
Page 16
[JOB#1220]: STOCK ADD PRESET
STAMP Stamp
01/01/00 0:06 000000 # 0005  
#1220 *PGMâ* Job Code/Mode title
P 000001 10 00.000 Old stock 10 .000 (Input stock) s 1010 .000 New stock
[JOB#1221]: STOCK SUB PRESET
STAMP Stamp
01/01/00 0:06 000000 # 0005  
#1221 *PGMé* Job code/Mode title
P 000001 10 00.000 Old stock
-10.000 (Input stock) s 990.000 New stock
[JOB#1222]: STOCK INVENTORY PRESET
STAMP Stamp
01/01/00 0:06 000000 # 0005  
#1222 *PGMé* Job code/Mode title
P 000001 10 00.000 Old stock
500.000 (New stock) - (Old stock) s 15000.000 New stock (Input stock)
[JOB#2220]: LINK PLU PRESET OR READING
Key operation
STAMP Stamp
01/01/00 0:06 000000 # 0010  
#2220 *PGMâ* Job code/Mode title
000001-999999 Start No. – End No. P 000002 L p000011 PLU code/Link PLU code (Max 5) p000012 /Link PLU code
[JOB#2221]: SET MENU PRESET OR READING
Key operation
STAMP Stamp
01/01/00 0:06 000000 # 0011  
#2221 *PGMâ* Job code/Mode title
000001-999999 Start No. – End No. P 000001 S p000002 PLU code/Set PLU code (Max. 10) p000003 /Set PLU code
[JOB#1300]: FUNCTION PRESET READING
Key operation
2220
Start No. End No.
Single item
XXXXXX
XXXXXX
All
TL
2221
Start No.
XXXXXX
All
End No.
Single item
XXXXXX
TL
1300
TL
– 15 –
Page 17
STAMP Stamp
01/01/00 0:06 000000 # 0015  
#1300 *PGMâ* Job code/Mode title
F001[~]é Function No./Text S -0.00 Sign, Rate l17 HALO F002[~]â S -0.00 l17 F005 ‰é S -0.00% Rate l100 .00% F006 ‰â S -0.00% Rate l100 .00% F 009 set plu­F 011 tax1 st F 012 tax2 st F 013 tax3 st F 015 vat 1 F 016 vat 2 F 017 vat 3 F019 NETé F020 NETâ F 021 cp plu F 022 refund F 023 \ F 024 ¡ mode F 025 mgr ¿ F 026 sbtl ¿ F 029 vat sft F 030 tax dele F 031 vp cnt F 032 no sale HALO F 033 g.c. cnt F 036 ***ra l18 F 038 ***po l18 F 041 C ash l18 00000000000 (* 1) PGM F 043 check l18 00000000000 F 047 credit 1 l18 00000000000 F 048 credit 2 l18 00000000000 F 051 exch1
0. 0000 F 058 ****cid 999999 9.99 F 060 ca/ch id F 061 chk/cg
999999.99 F 062 guest F 063 com.sal1
0.00% F 064 com.sal2
0.00% F 065 com.sal3
0.00%
F 066 non com. F 067 order tl F 068 paid tl F 069 dom.cur1 F 073 *ch id F 074 *dept tl F 075 dept(-) F 080 net 1 F 081 net 2 F 082 net 3 F 084 subtotal F 085 mdse st F 086 ***total F 087 change F 088 due F 089 items F 090 plu st F091 COPY F 092 g.c copy F 093 ave. F 094 G roup01 F 095 G r0up02 F 096 G roup03 F 097 G roup04 F 098 G roup05 F 099 G roup06 F 100 G roup07 F 101 G roup08 F 102 G roup09 F106 O~P F 107 com.amt1 F 108 com.amt2 F 109 com.amt3 F 110 ccm.ttl F111 DEPT F 112 group F113 PLU F 114 stock F 115 trans. F 116 tl-id F 117 sales F 118 cashier F 119 hourly F 120 daily F 121 set plu F 122 ttl tax F123 NET F 124 zero sal F 125 category
(* 1)PGM: ABCDEFGHIJK
A: EFT function compulsory/noncompulsory 1/0 B: Footer print Yes/No 1/0 C: Non-add code entry compulsory/noncompulsory 1/0 D: Change due Disable/Enable 1/0 E: VP compulsory/noncompulsory 1/0 F: (Not used) 0 G: (Not used) 0 H: (Not used) 0 I: (Not used) 0 J: Drawer opening No/Yes 1/0 K: Entry of amount tenderd
compulsory/noncompulsory compulsory/inhibit
(Cash, check) 1/0 (CR1 to 8) 1/ 0
– 16 –
Page 18
[JOB#2600]: READING OF OTHER
Key operation
STAMP Stamp
01/01/00 0:08 000000 # 0017  
#2600 *PGMâ* Job code/Mode title
#2615 10 SLIP/VP #2616 (* 1) Optional feature 01 0000 0000 02 0000 0000 03 0000 0000 04 0000 0000 05 0000 0000
06 0000 0000 07 0000 0000 08 0000 0000 09 0000 0000 10 0000 0000 11 0000 0000 12 0000 0000 13 0000 0000 #2617 000 Till timer #2619 0 00 (* 3) Hourly report #2620 Stack report 1 #2630 0000 Secret code PGM1 #2631 0000 X1/Z1 #2632 0000 X2/Z2
(* 1)Optional feature: ABCDEFGH
MRS = 00000000
x: 1 MRS = 00000000
A: OP X/Z report Disable/Enable 1/0 B: PO operation in REG mode Disable/Enable 1/0 C: (Not used) 0 D: "RFND" key entry in REG mode Disable/Enable 1/0 E: Direct void function in REG mode Disable/Enable 1/0 F: Indirect void in REG mode Disable/Enable 1/0 G: Subtotal void in REG mode Disable/Enable 1/0 H: Refund VP Compulsory/Non compulsory 1/0
x: 2 MRS = 00000000
A: The first last item void Disable/Enable 1/0 B: PLU level shift system Manual/Auto 1/0 C: PLU level shift system MGR/MGR & REG 1/0 D: Printing of the number of purchases Y es/No 1/0 E: Time print No/Yes 1/0 F: Journal select/Full print 1/0 G: Item VP Disable/Enable 1/0 H: (–) VP Compulsory/Non compulsory 1/0
x: 3 MRS = 00000000
A: (Not used) 0 B: (Not used) 0 C: Zero skip in Cashier report No/Yes 1/0 D: Zero skip in Transaction report No/Yes 1/0 E: Zero skip in DEPT. report No/Yes 1/0 F: Zero skip in PLU report No/Yes 1/0 G: Zero skip in hourly report No/Yes 1/0 H: Zero skip in Daily net report No/Yes 1/0
x: 4 MRS = 00000000
A: (Not used) 0 B: (Not used) 0 C: Vat/Tax amount printing on R/J No/Yes 1/0 D: Taxable amount printing on R/J No/Yes 1/0 E: Net amount printing on R/J No/Yes 1/0 F: (Not used) 0 G: (Not used) 0 H: When PLU level system is "Auto" (x: 2 B = 0),
PLU level returns to level 1 by one receipt/by one item. 1/0
x: 5 MRS = 00000000
A: (Not used) 0 B: (Not used) 0 C: (Not used) 0 D: VAT shift system By shift key/by cashier 1/0 E: (Not used) 0 F: (Not used) 0 G: (Not used) 0
H: (Not used) 0 x: 6 (Not used) MRS = 00000000 x: 7 (Not used) MRS = 00000000 x: 8 (Not used) MRS = 00000000 x: 9 (Not used) MRS = 00000000 x: 10 (Not used) MRS = 00000000 x: 11 (Not used) MRS = 00000000 x: 12 (Not used) MRS = 00000000 x: 13 MRS = 00000000
A: Credit totalizer update if RA/PO finalized
by Credit key Yes/No 1/0 B: Separater line in report Separater line/1 line 1/0 C: (Not used) 0 D: (Not used) 0 E: (Not used) 0 F: (Not used) 0 G: (Not used) 0 H: (Not used) 0
(* 2)Hourly report : a bc
a: Hourly report format by 15 minutes/by 30 minutes 1/0 bc:start hour 00 to 23
2600
TL
2616 X ABCDEFGH
0
ST TL
– 17 –
Page 19
[JOB#2640]: READING OF TEXT PROGRAMMING
Key operation
STAMP Stamp
01/01/00 0:08 000000 # 0019  
#2640 *PGMâ* Job code/Mode title
#2641 01 en try er ror Message text 02 mi sopera tion 03 no record 04 pa per em pty 05 se cret c ode 06 07 me mory f ull 08 09 10 ou t of s tock 11 sb tl com pul. 12 te nd com pul. 13 14 15 16 17 18 19 20 21 22 ca shier err. 23 en try er r ca 24 25 26 27 28 29 30 31 # compul sory 32 no t assi gned 33 no t chan ge 34 ov er lim it. 35 in h. ope n pr 36 in h. uni t pr 37 no t non- tend 38 39 p off in vp 40 41 42 43 44 45 46
47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 bu ffer f ull 68 69 70 71 72 ef t erro r 73 ef t brea k 74 75 76 cl ose dr awer 77 78 79 80 81 en tr sec ret# 82 se nd 83 re ceive 84 se nd ok 85 re ceive ok 86 co m. err or 87 da ta err or 88 ti me out 89 ca ncel #2644 001 de pt pri ce Guidance 002 de pt fun c. 003 de pt tax able 004 de pt hal o 005 de pt tex t 006 de pt com .grp 007 de pt gro up 008 de pt drc tkey 009 pl u asg. dept 010 pl u pric e 011 pl u base qty 012 pl u stck add 013 pl u stck sub 014 pl u stck ovw 015 pl u func tion 016 pl u taxa ble 017 pl u text 018 pl u com. grp 019 pl u drct key 020 li nk plu
2640
TL
– 18 –
Page 20
021 se t plu 022 pl u code rng 023 pl u func rng 024 pl u stts rng 025 pl u com rng 026 ra te prg ram 027 mi sc key pgm 028 fn c key halo 029 md iakey halo 030 % halo 031 fu nc tex t 032 mi sc key pgm 033 mi sc key pgm 034 md ia key pgm 035 md iakey halo 036 cs r code pgm 037 cs r name pgm 038 cs r pgm 039 da te pro gram 040 ti me pro gram 041 mc hn no. pgm 042 cc no. p gm 043 lo gotext pgm 044 vp count 045 op t feat ure 046 dr awer a larm 047 ho urlyre port 048 st ack re port 049 se cret(p gm1) 050 se cret(x 1z1) 051 se cret(x 2z2) 052 me ssge t ext 053 gu id tex t 054 ta x rate 055 pr ice 056 en ter de pt# 057 si gn (-) 058 si gn (+) 059 ta xable1 :yes 060 ta xable1 :no 061 ta xable2 :yes 062 ta xable2 :no 063 ta xable3 :yes 064 ta xable3 :no 065 va t:yes 066 va t:no 067 pr t csr: yes 068 pr t csr: no 069 vp compl:yes 070 vp compl:no 071 si f 072 si cs 073 no rmal 074 de lete 075 op en&pre st 076 pr eset 077 op en 078 in hibite d 079 ha lo(exp .) 080 ha lo(amo unt) 081 ha lo(rat e) 082 co m.grp 083 gr oup 084 ba se q’t y
085 st ock(ad d) 086 st ock(su b) 087 st ock(ov er) 088 ra te 089 it em 090 st 091 ef t cmpl 092 ef t nonc mpl 093 fo oter :yes 094 fo oter :no 095 # cmpl 096 # noncmp l 097 du e disa ble 098 du e enab le 099 dr w open :yes 100 dr w open :no 101 tn d cmpl :yes 102 tn d cmpl :no 103 tn d inh. 104 en ter pl u# 105 en t.csr code 106 en t.csr no 107 en t.drw# 108 g. c copy yes 109 g. c copy no 110 va t sft stat 111 va t sft not 112 en t.dept # 113 en t.key# 114 en t.func # 115 en t.pos. code 116 en ter ta x no 117 en t.tax rate 118 lo wer ta x 119 en ter ms g no 120 en ter gi d no 121 (f ixed d ata) 122 en tercoo okey ‘123 da ta sen d 124 da ta rcv . 125 or g’zer rcv. 126 on l t.no . 127 on l mode m 128 on l baud rate 129 on l code 130 on l time r
– 19 –
Page 21
[JOB#2900]: AUTO KEY READING
Key operation
STAMP Stamp
01/01/00 0:08 000000 # 0005  
#2900 *PGMâ* Job code/Mode title
#üé 1 key 0 key 0 key total #üâ D ü é (DEPT01) D ü â P 000001 (PLU000001) : #üå 1 key 0 key 0 key total check
[JOB#1500]: CASHIER READING REP.
Key operation
STAMP Stamp
01/01/00 0:08 000000 # 0016  
#1500 *PGMâ* Job code/Mode title
01csr# 01 Cashier code/Name 00 00d1 Drawer No. 02csr# 02 00 00d1 03csr# 03 00 00d1 04csr# 04 00 00d1
[JOB#2700]: TAX TABLE READING REP.
Key operation
STAMP Stamp
01/01/00 0:08 000000 # 0005  
#2700 *PGMâ* Job code/Mode title
tax1 10.0 000% VAT No./Rate
04.00 Lower tax limit tax2 4.0000% VAT No./Rate
0.00 Lower tax limit tax3 5.0000%
0.00
2900
TL
1500
TL
2700
TL
– 20 –
Page 22
[JOB#2119]: DIRECT KEY READING REP.
Key operation
STAMP Stamp
01/01/00 0:08 000000 # 0005  
#2119 *PGMâ* Job code/Mode title
üüé l1 Düé Key no./Dept code or PLU code üüâ l1 Düâ *** When Dept code is assigned to üüä l1 Düä *** the direct key, the same Dept üüà l1 Düà *** code isassigned to each level. Ç üåé l1 P000001 l2 P 001001 üåâ l1 P000002 l2 P 001001 Ç éåé l1 ---­ Ç
2. Programming
[JOB#1110]
PROGRAMMING OF DEPT. PRICE
XX: DEPT-CODE = 01 ∼ 50 YYYYYY: PRICE = 0 ∼ 999999 Preset price is max. 6 digits. Price can be programmed for each dept. If this programming is per­formed, the ECR is automatically programmed to allow preset price entry even when it has been programmed not to allow preset price entry in dept. function programming (JOB#2110).
MRS = 000000
[JOB#2110]
PROGRAMMING OF DEPT. FUNCTION
XX: DEPT. code = 01 ∼ 50
XXA: Prin ting on the cashier report A
No 0 Yes 1
XXB: Item validation printing B
Non compulsory 0
Compulsory 1 C, D: Not used (Fixed at "00")
XXE: SICS Function E
Normal 0
Single item cash sale 1
Single item finalize 2
F: Not used (Fixed at "0")
XXG: Amou nt entry ty pe G
Inhibited 0
Open 1
Preset 2
Open and pres et 3 MRS = 0000001
2119
TL
1110
YYYYYY
XX
No change
price
DEPT. CODE
For the next DEPT.
TLST
2110 XX
DEPT. CODE
CL
ABCDEFG
For next code
No change
TLST
– 21 –
Page 23
[JOB#2111]
DEPT. TAX STATUS PROGRAMMING
XX: DEPT. CODE = 01 ∼ 50 A, B: Not used (Fixed at "00")
C: VAT 1 C
Non taxable 0 Taxable 1
D: Taxable 3 D
Non taxable 0 Taxable 1
E: Taxable 2 E
Non taxable 0 Taxable 1
F: Taxable 1 F
Non taxable 0 Taxable 1
MRS = 000000
[JOB#2112]
DEPT. HALO (limit) preset
XX: DEPT. CODE = 01 ∼ 50
A: Mantissa (HALO) = 1 ∼ 9 B: Exponent (HALO) = 0 ∼ 7
* Items A and B indicate A × 10B. Any amount below that value is
enable within 9999999.
MRS = 17
[JOB#2114]
DEPT. TEXT PROGRAMMING
XXX: DEPT. CODE = 01 ∼ 50
Characters can be entered by using alphabetic keys or numeric keys. Please refer to section 3.
MRS = DPT. XX
[JOB#2115]
COMMISSION GROUP PROGRAMMING
XX: DEPT. CODE = 01 ∼ 50
A: Group No. = 0~3
[JOB#2116]
PROGRAMMING OF DEPT. GROUP
XX: DEPT. code = 01 ∼ 50 AA: Group No. = 1 ~ 14
Group No. Group name
1~9 Plus department
10 Minus department 11 Plus HASH department 12 Minus HASH department 13 Plus BR department 14 Minus BR department
MRS = 01
A selection of the group "Hash" and "BR" are inhibited when the hash function is programmed as disabled in SRV mode.
[JOB#2119]
LINK NUMBER PROGRAMMING FOR DIRECT DEPT. KEYS
DEPT. code is assigned to the key no. Which has been programmed in JOB#951 programming.
AB: DEPT. CODE = 01 ∼ 50
[JOB#1200]
Creating/assigning PLUs and the associated departments.
XXXXXX: PLU code = 01 ∼ 999999
AB: DEPT. code = 01 ∼ 50 If the record of entered PLU code is not in PLU file at this program-
ming, it will be created in PLU file. MRS = 01
2111 XX
DEPT. CODE
CL
ABCDEF
For the next DEPT.
No change
ST TL
2112
AB
XX
DEPT. CODE
For the next DEPT.
No change
TLST
2114 XX
DEPT. CODE
CL
Character key
For the next DEPT.
No change
ST TL
2115 XX
DEPT. CODE
CL
A
For next code
No change
TLST
2116 XX
DEPT. CODE
CL
AA
Next code
No change
TLST
2119
XXX
KEY No.
Next DEPT.
AB
DEPT. code
0
ST TL
1200
XXXXXX
PLU code
AB
No change
ST TL
– 22 –
Page 24
[JOB#1210]
PRICE PROGRAMMING FOR PLUS
XXXXXX: PLU CODE = 1 ∼ 999999 YYYYYY: Amount = 0 ∼ 999999
If the record of entered PLU code is not in PLU file at this program­ming, it will be created in PLU file.
MRS = 000000
[JOB#1211]
PLU BASE Q’TY PROGRAMMING
XXXXXX: PLU code = 1 ∼ 999999
ZZ: Base quantity = 00 ∼ 99
If the record of entered PLU code is not in PLU file at this program­ming, it will be created in PLU file.
[JOB#1220]
PROGRAMMING OF PLUS STOCK (ADD)
XXXXXX: PLU code = 1 ∼ 999999 YYYY.YYY: Stock value = 0.001 ∼ 9999.999
The stock value is max. 7 digits. (4 integers + 3 decimals) The stock value entered is added to the PLU stock counter.
MRS = 0.000
[JOB#1221]
PROGRAMMING OF PLU STOCK (SUB)
XXXXXX: PLU code = 1 ∼ 999999 YYYY.YYY: Stock value = 0.001 ∼ 9999.999
The stock value is max. 7 digits. (4 integers + 3 decimals) The stock value entered is subtracted from the PLU stock counter.
MRS = 0.000
[JOB#1222]
PROGRAMMING OF PLU STOCK (OVERWRITE)
XXXXXX: PLU code = 1 ∼ 999999 YYYYYYY: Stock value = 0.001 ∼ 9999 . 99 9
The stock value is max. 7 digits. (4 integers + 3 decimals) The stock value entered is overrited to the PLU stock counter.
MRS = 0.000
[JOB#2210]
PLU function programming
XXXXXX: PLU code = 1~999999
A, B: Not used (Fixed at"00")
C: Amount entry type C
Inhibited 0 Open 1 Preset 2 Open and preset 3 Delete 4
If the record of entered PLU code is not in PLU file at this program­ming, it will be created in PLU file.
MRS = 002
1210
XXXXXX
PLU CODE
YYYYYY
For next code
No change
ST TL
1211
ZZXXXXXX
PLU CODE
For the next PLU
No change
TLST
1220
YYYY.YYYXXXXXX
PLU CODE
For the next PLU
ST TL
1221
XXXXXX
Next code
PLU CODE
YYYY.YYY
ST TL
1222
XXXXXX
PLU CODE
YYYYYYY
Next code
No change
ST TL
2210 ABC
XXXXXX
No change
PLU code
For next code
CL
ST TL
– 23 –
Page 25
[JOB#2211]
PLU TAX STATUS PROGRAMMING
XXXXXX: PLU code = 1 ∼ 999999
A: Sign A
+ 0 –1
XXXXXB: Not used (Fixed at "0")
C: VAT 1 C
Non taxable 0 Taxable 1
D: Taxable 3 D
Non taxable 0 Taxable 1
E: Taxable 2 E
Non taxable 0 Taxable 1
F: Taxable 1 F
Non taxable 0 Taxable 1
If the record of entered PLU code is not in PLU file at this program­ming, it will be created in PLU file.
MRS = 000000
[JOB#2214]
PLU TEXT PROGRAMMING
XXXXXX: PLU CODE = 1 ∼ 999999 Characters can be entered by using alphabetic keys or numeric keys. Please refer to section 3.
MRS = PLXXXXXX
[JOB#2215]
COMMISSION GROUP PROGRAMMING
XXXXXX: PLU code = 1 ~ 999999
XXXXXA: Group No. = 0 ~ 3
If the record of entered PLU code is not in PLU file at this program­ming, it will be created in PLU file.
[JOB#2219]
PLU CODE DEFINITION FOR DIRECT PLU KEYS
ABCDEF: PLU code = 1~999999 PLU code is assigned to the key No. which has been programmed in
JOB#951 programming.
[JOB#2220]
LINKED PLU PROGRAMMING
XXXXXX: PLU code = 1 ∼ 999999 YYYYYY: PLU code = 1 ∼ 999999
When the "ST" key is pressed without entering any number as the first PLU code (YYYYYY), the previous data is cleared.
PLU code should already be defined when they are used in program­ming here.
MRS = 0
[JOB#2221]
SET PLU PROGRAMMING
XXXXXX: PLU code = 1 ∼ 999999 YYYYYY: PLU code = 1 ∼ 999999
When the "SBTL" key is pressed without entering any number as the first PLU code (YYYYYY), the previous data is cleared.
The PLU code (XXXXXX) can not be set the set PLU code (YYYYYY).
PLU code must already be defined when it is used in programming here.
MRS = 0
2211 XXXXXX
PLU code
CL
ABCDEF
No change
For the next PLU
TLST
2214 XXXXXX
PLU code
CL
Character key
For the next PLU
No change
TLST
2215 A
XXXXXX
No change
PLU code
For next code
CL
ST TL
2219 ABCDEFXXX
Next code
Key No.
0
PLU code
L3
L1
L2
ST TL
2220
YYYYYYXXXXXX
Max. 5 times
0
PLU CODE
TLST
2221
YYYYYY
XXXXXX
Max. 10 times
0
PLU code
TLST
– 24 –
Page 26
[JOB#2230]
PLU CODE PROGRAMMING (range)
XXXXXX: Start PLU code = 1 ∼ 999999 YYYYYY: End PLU code = 1 ∼ 999999
AB: Dept. code = 1~50
* All are set with the contents of Start PLU setting.
[JOB#2231]
PLU function programming (RANGE)
* All are set with the contents of Start PLU setting.
XXXXXX: Start PLU code = 1~999999 YYYYYY: End PLU code = 1~999999
A, B: Not used (Fixed at "00")
C: Amount entry type C
Inhibited 0 Open 1 Preset 2 Open and preset 3 Delete 4
If the record of entered PLU code is not in PLU file at this program­ming, it will be created in PLU file.
MRS = 000
[JOB#2232]
PLU TAX STATUS PROGRAMMING (RANGE)
* All are set with the contents of Start PLU setting. XXXXXX: Start PLU code = 1 ∼ 999999 YYYYYY: End PLU code = 1 ∼ 999999
A: Sign A
+ 0
–1 B: Not used (Fixed at "0") C: VAT 1 C
Non taxable 0 Taxable 1
D: Taxable 3 D
Non taxable 0 Taxable 1
E: Taxable 2 E
Non taxable 0 Taxable 1
F: Taxable 1 F
Non taxable 0 Taxable 1
[JOB#2235]
Commission group programming (RANGE)
* All are set with the contents of start PLU setting.
XXXXXX: Start PLU code = 1~999999 YYYYYY: End PLU code = 1~999999
A: Group No. = 0~3
2230
YYYYYYXXXXXX
PLU CODE
AB
No change
∗
PLU CODE
TLST
2231
XXXXXX
PLU CODE
ABC
No change
∗
ST TL
CL
YYYYYY
2232
XXXXXX
PLU CODE
ABCDEF
No change
∗
YYYYYY
ST TL
2235
YYYYYYXXXXXX
PLU CODE
A
No change
∗
TLST
– 25 –
Page 27
[JOB#1310]
RATE PROGRAMMING
XXX: Fanction No. YYYY. YYYY: Rate
Function
No.
Function Entry range Remarks
1 (–)1
0 to 9999.99 (–) unit price
2 (–)2 3 (–)3 4 (–)4 5%1
0 to 100.00 % rate
6%2 7%3 8%4 51 Exchange 1
0 to 9999.9999 Rate
52 Exchange 2 53 Exchange 3 63 Commission 1
0 to 999.99 Rate
64 Commission 2 65 Commission 3
MRS = 0
[JOB#2311]
MISC KEY PROGRAMMING 1
XXX: Function No.
Function No. Function
1 (–)1 2 (–)2 3 (–)3 4 (–)4 5%1 6%2 7%3 8%4
A: Sign A
+ 0
–1
B, C, D, E, F: Not used (Fixed at "00000")
MRS = 100000
[JOB#2312, 2322]
HALO PROGRAMMING
XXX: Function No.
A: Mantissa (0 to 9) B: Exponent (0 to 8)
JOB#
Function
No.
Function Remarks
2312
1 (–)1
Item B is specificable within the range from 0 to
7.
2 (–)2 3 (–)3 4 (–)4
36 RA
Item B is specificable within the range from 0 to
8.
37 RA2 38 PO 39 PO2
2322
41 CA1
Item B is specificable within the range from 0 to
8.
42 CA2 43 CH1 44 CH2 45 CH3 46 CH4 47 CR1 48 CR2 49 CR3 50 CR4
Entry range, system: A × 10
B
MRS = 17 ((–)1~(–)4)
18 (Others)
[JOB#2313]
MISCELLANEOUS KEY PROGRAMMING (% HALO)
XXX: Function No. YYY. YY: % HALO
Function
No.
Function Remarks
5%1 6%2 7%3 8%4
1310 YYYY.YYYYXXX
Function No. Rate
No change
TLST
2311 ABCDEFXXX
Function No.
No change
TLST
2312 2322
ABXXX
Function code
No change
ST TL
2313 YYY.YY
XXX
No change
TLST
– 26 –
Page 28
[JOB#2314]
TEXT PROGRAMMING FOR MISC KEYS
XXX: FUNCTION CODE Characters can be entered by using character keys or numeric keys.
the key entery sequence for entering one character by numeric keys is as follows:
XXX → 00 key XXX: CHARACTER CODE (3DIGITS) Please refer to section 3
F-NO. FUNCTION DEFAULT TEXT
1 (–)1
[~]é
2 (–)2
[~]â
3 (–)3
[~]ä
4 (–)4
[~]à
5%1
‰é
6%2
‰â
7%3
‰ä
8%4
‰à
9 SET PLU (–)
set plu-
10 DIFFER
differ
11 TAXABLE1 ST
tax1 st
12 TAXABLE2 ST
tax2 st
13 TAXABLE3 ST
tax3 st
14 TAXABLE ST
tax st
15 VAT/TAX 1
vat 1
16 VAT/TAX 2
vat 2
17 VAT/TAX 3
vat 3
18 VAT/TAX
vat
19 NET1
NETé
20 NET2
NETâ
21 COUPON PLU
cp plu
22 REFUND
refund
23 VOID
"
24 VOID MODE
" mode
25 MANAGER VOID
mgr "
26 SBTL VOID
sbtl "
27 HASH VOID
hash "
28 HASH REFUND
hash rf
29 VAT SHIFT
vat sft
30 VAT/TAX DELETE
tax dele
31 VP COUNTER
vp cnt
32 NO SALE
no sale
33 G.C. COUNTER
g. c. cnt
34 35 36 RA
***ra
37 RA2
***ra2
38 PO
***po
39 PO2
***po2
F-NO. FUNCTION DEFAULT TEXT
40 CHECK CASHING
ca/chk
41 CASH
C ash
42 CASH2
C ash2
43 CHECK1
check
44 CHECK2
check2
45 CHECK3
check3
46 CHECK4
check4
47 CREDIT1
credit1
48 CREDIT2
credit2
49 CREDIT3
credit3
50 CREDIT4
credit4
51 EXCHANGE1
exch1
52 EXCHANGE2
exch2
53 EXCHANGE3
exch3
54 EXCHANGE4
exch4
55 EXCHANGE1 IS
exch1 is
56 EXCHANGE2 IS
exch2 is
57 EXCHANGE3 IS
exch3 is
58 CASH IN DRAWER
****cid
59 CASH/CHECK IS
ca/ch is
60 CASH/CHECK IN DRAWER
ca/ch id
61 CHECK CHANGE
chk/cg
62 GUEST
guest
63 COMMISSION SALE1
com.sal1
64 COMMISSION SALE2
com.sal2
65 COMMISSION SALE3
com.sal3
66 NON COMMISSION SALE
non com.
67 ORDER TOTAL
order tl
68 PAID TOTAL
paid tl
69 DOMESTIC CURRENCY1
dom.cur1
70 DOMESTIC CURRENCY2
dom.cur2
71 DOMESTIC CURRENCY3
dom.cur3
72 DOMESTIC CURRENCY4
dom.cur4
73 CHECK IN DRAWER
*ch id
74 (+) DEPT TOTAL
*dept tl
75 (–) DEPT TOTAL
dept(-)
76 HASH (+) DPT TOTAL
*hash tl
77 HASH (–) DPT TOTAL
hash(-)
78 BOTTLE (+) TOTAL
*bttl tl
79 BOTTLE (–) TOTAL
bttl(-)
80 NET 1 (TAXABLE-VAT1)
net 1
81 NET 2 (TAXABLE-VAT2)
net 2
82 NET 3 (TAXABLE-VAT3)
net 3
83 NET (TAXABLE-VAT)
net
84 SUBTOTAL
subtotal
85 MDS SBTL
mdse st
86 TOTAL
***total
87 CHANGE
change
88 DUE
due
89 ITEMS
items
90 PLU ST
plu st
2314 Character keyXXX
Function number
Max. 8 char.
No change
TLST
– 27 –
Page 29
F-NO. FUNCTION DEFAULT TEXT
91 COPY RCPT TITLE
COPY
92 G.C. COPY TITLE
g.c. copy
93 AVERAGE
ave.
94 GROUP1
Group01
95 GROUP2
Group02
96 GROUP3
Group03
97 GROUP4
Group04
98 GROUP5
Group05
99 GROUP6
Group06
100 GROUP7
Group07
101 GROUP8
Group08
102 GROUP9
Group09
103 CCD
CCD
104
CCD DIFFER
ccd dif.
105 CCD DIFFER TOTAL
dif. tl
106 ORDER TL-PAID TL
O~P
107 COMMISSION AMOUNT1
com. amt1
108 COMMISSION AMOUNT2
com. amt2
109 COMMISSION AMOUNT3
com. amt3
110 COMMISSION AMOUNT TTL
com. ttl
111 DEPT. REPO. TITLE
DEPT
112 GROUP REPO. TITLE
group
113 PLU REPO. TITLE
PLU
114 STOCK REPO. TITLE
stock
115 TRANS. REPO. TITLE
trans.
116 CID REPO. TITLE
tl-id
117 COM. SALES REPO. TITLE
sales
118 CASHIER REPO. TITLE
cashier
119 HOURLY REPO. TITLE
hourly
120 DAILY NET REPO. TITLE
daily
121 SET PLU TITLE
set plu
122 TOTAL TAX
ttl tax
123 NET WITHOUT TAX
NET
124 ZERO SALES REPRT TITLE
zero sal
125 CATEGORY REPO. TITLE
category
126 DIFFER SUBTOTAL
diff st
[JOB#2315]
MISC KEY PROGRAMMING (%)
XXX: Function No.
A: % type A
Subtotal % 0 Item % 1
Function No. Function Remarks
5%1 6%2 7%3 8%4
MRS = 0
[JOB#2316]
MISC KEY PROGRAMMING ($ )
XXX: Function No.
A: $ type A
Subtotal $ 0 Item $ 1
Function No. Function Remarks
1 (—) 1 2 (—) 2 3 (—) 3 4 (—) 4
MRS = 0
[JOB#2320]
MEDIA KEY PROGRAMMING
XXX: Function No.
Function
No.
Function A B C D E F G H I J K
41 CA1 ÉFFFF————FF 42 CA2 ÉFFFF————FF 43 CH1 FFFFF————FF 44 CH2 FFFFF————FF 45 CH3 FFFFF————FF 46 CH4 FFFFF————FF 47 CR1 FFFFF————FF 48 CR2 FFFFF————FF 49 CR3 FFFFF————FF 50 CR4 FFFFF————FF
*Items marked with on (F) are programmable.
A: EFT function A
Non compulsory 0 Compulsory 1
B: Footer print B
No 0 Yes 1
C: Non-add code entry C
Non compulsory 0 Compulsory 1
D: Change due D
Enable 0 Disable 1
E: VP E
Non compulsory 0 Compulsory 1
F, G, H, I: Not used (Fixed at "0000")
2315
XXX A
No change
ST TL
2316
XXX A
No change
ST TL
2320
XXX ABCDEFGHIJK
No change
ST TL
– 28 –
Page 30
J: Drawer opening J
Yes 0 No 1
K: Entry of amount tended K
Non compulsory (Cash, Check) Inhibit (CR1 to CR8)
0
Compulsory 1
MRS=00000000000
[JOB#2321]
MEDIA KEY FUNCTION PROGRAM (AMOUNT HALO)
XXX: Function No.
YYYYYYYYY: Limitation amount
Func.
No.
Function Entry range MRS
58 61 40
CID (Sentinel) CHK CHANGE CA/CHK
0 to 9999999.99 0 to 999999.99 0 to 999999.99
9999999.99
999999.99
999999.99
[JOB#1500]
CASHIER CODE DIFINITION
XXX: Cashier No.= 1 ∼ 15 YYYY: Cashier code = 00 ∼ 99
MRS = 01;1, 02;2, 03;3, 04;4, 05;5, 06;6 ~ 15;15
[JOB#1514]
CASHIER NAME PROGRAMMING
YYYY: Cashier code = 01 ∼ 99 Characters can be entered by using character keys or numeric keys. The key entry sequence for entering one character by numeric keys is as follows: XXX → 00 KEY XXX: Character code (3 digits) Please refer to section 3. Max. 8 characters Mrs = ’Space’
[JOB#2510]
CASHIER PROGRAMMING
YY: Cashier code = 01~99
A: G.C. copy A
Enable 0 Disable 1
B: VAT shift B
Not 0 State 1
C, D: Not used (Fixed at "00")
E: Drawer No. E
Not open 0 Drawer No. 1~2
MRS = 1
[JOB#2610]
DATE SETTING
XXYYZZ: Date (Year-Month-Day/Day-Month-Year/Month-Day-Year) * The date entry format complies with the applicable SRV-mode
programming.
MRS = 010100
[JOB#2611]
TIME SETTING
XX: Hour (00 ∼ 23) YY: Minute (00 ∼ 59)
MRS = 0
[JOB#2612]
MACHINE NUMBER SETTING
XXXXXX: Machine number (0 ∼ 999999) MRS = 0
[JOB#2613]
CONSECUTIVE NUMBER SETTING
XXXX: Consecutive number (0000 ∼ 9999) MRS = 0000
2321 XXX
YYYYYYYY
No change
ST TL
1500 XX YY
No change
ST TL
1514
YY
Character key
No change
TLST
2510 YY
ABCDE
No change
ST TL
2610
XXYYZZ
TL
0
2611 XXYY
TL
0
2612
XXXXXX
TL
0
2613 @/FOR CA/ATXXXX
– 29 –
Page 31
[JOB#2614]
LOGO TEXT PROGRAMMING
X: 1 ∼ 6 1 (24 char.)
2 (24 char.) 3 (24 char.) 4 (24 char.) 5 (24 char.) 6 (24 char.)
Character can be entered by using character keys or numeric keys. The key entry sequence for entering one character by numeric keys is as follows:
XXX → 00 Key XXX: Character code (3 digits)
Please refer to section 3.
ER-A460 ER-A470
MRS =
SHARP pres ents t he ER~Aàçü SHARP IS THE BEST
SHARP presents the ER~Aàêü SHARP IS THE BEST
NOTE: This programming is related to JOB# 912D programming.
Only when "6-line header instead of a stamp" is selected by JOB# 912D programming, all 6 lines are programmable. When "3-line header" is selected, upper 3 lines (1st-3rd line) are programmable. When "3-line footer" is selected, lower 3 lines (4th-6th line) are programmable.
[JOB#2615]
Programming of the limits to TRY ST feed line and No. of times of validation printing.
Y: No. of times of validation printing = 0 ∼ 9 X: Feed line after depression
of differ ST key. = 0 ∼ 9
MRS = 10
[JOB#2616]
OPTIONAL FEATURE
X: 1 MRS = 00000000
A: OP X/Z report A
Enable 0 Disable 1
B: PO operation in REG mode B
Enable 0 Disable 1
C: Not used (Fixed at "0")
D: "RFND" key entry in REG mode D
Enable 0 Disable 1
E: Direct void function in REG mode E
Enable 0 Disable 1
F: Indirect void in REG mode F
Enable 0 Disable 1
G: Subtotal void in REG mode G
Enable 0 Disable 1
H: Refund VP H
Non compulsory 0 Compulsory 1
2614
Character key
X
Position code
No change
ST TL
2615 YX
0
TL
2616
ABCDEFGH
0
X
ST TL
– 30 –
Page 32
X: 2 MRS = 00000000
A: The first last item void A
Enable 0 Disable 1
B: PLU level shift system B
Auto 0 Manual 1
C: PLU level shift system C
MGR & REG mode 0 MGR mode 1
D: Printing of the number of purchases D
No 0 Yes 1
E: Time print E
Yes 0 No 1
F: Printing of journal F
Full print 0 Journal select 1
G: Item VP G
Enable 0 Disable 1
H: (–) VP H
Non compulsory 0 Compulsory 1
X: 3 MRS = 00000000
A, B: Not used (Fixed at "00")
C: Zero skip in Cashier report C
Yes 0 No 1
D: Zero skip in Transaction report D
Yes 0 No 1
E: Zero skip in Dept. report E
Yes 0 No 1
F: Zero skip in PLU report F
Yes 0 No 1
G: Zero skip in Hourly report G
Yes 0 No 1
H: Zero skip in Daily net report H
Yes 0 No 1
X: 4 MRS = 00000000
A, B: Not used (Fixed at "00")
C: Vat/Tax amount printing on R/J C
Yes 0 No 1
D: Taxable amount printing on R/J D
Yes 0 No 1
E: Net amount printing on R/J E
Yes 0 No 1
F, G: Not used (Fixed at "00")
H: When PLU level system is "Auto" (X:2 B = 0), PLU
level returns method
H
By one item 0 By one receipt 1
X: 5 MRS = 00000000
A, B, C: Not used (Fixed at "000")
D: VAT shift system D
By cashier 0 By shift key 1
E, F, G, H: Not used (Fixed at "0000") X: 6 NOT USED MRS = 00000000 X: 7 NOT USED MRS = 00000000 X: 8 NOT USED MRS = 00000000 X: 9 NOT USED MRS = 00000000 X: 10 NOT USED MRS = 00000000 X: 11 NOT USED MRS = 00000000 X: 12 NOT USED MRS = 00000000 X: 13 MRS = 00000000
A: Credit totalizer update if RA/PO finalized by Credit
key
A
No 0 Yes 1
B: Separator line in report B
1 line 0 Separator line 1
C, D, E, F, G, H: Not used (Fixed at "000000")
[JOB#2617]
PROGRAMMING OF THE TIME INTERVAL FOR THE DRAWER ALARM
XXX: 0 ∼ 255 sec MRS = 000
2617
XXX
0
TL
– 31 –
Page 33
[JOB#2619]
HOURLY REPORT (Starting time)
a: Memory format A
30 minutes (24 hour) 0 15 minutes (12 hour) 1
bb: Starting time (hour): 00 ∼ 23 ex)
Case 1.
X1 Hourly report (#160) (15 min, start time = 7]
#160 7:00 (data) 7:15 (data) 7:30
                
                
12 hour started from 7:00
(data)
7:45 (data) subtotal (data)
| |
18:45 (data) subtotal (data) **:** (data) Data out of range (19:00 to 6:59)
[JOB#2620]
STACK REPORT
XX: JOB# SSSSSS: Start code EEEEEE: End code
JOB# REPORT NAME TYPE
00 General 10 DEPT./GROUP 13 DEPT. All group 20 PLU RANGE 24 PLU stock RANGE 27 PLU zero sales 29 PLU price category RANGE 30 Transaction 31 CID 32 Commission sale 50 All cashier 60 Hourly RANGE (only X report) 70 Daily net
[** ] Max. 70 step are programmable. "1 step" means the memory size used for one no range type JOB#. The RANGE type JOB# means "8 steps".
For example) The memory size for programming JOB#00, 20 and 50 is 10 steps. (ie. 1 step for JOB#00, 8 step for JOB#20, and 1 step for JOB#50. )
[JOB#2630, 2631, 2632]
SECRET CODE PROGRAMMING
#2630: PGM1 mode #2631: X1/Z1 mode #2632: X2/Z2 mode
* If "0" is entered, "compulsory secret code entry" is canceled. MRS = 0
2619 abb
0
TL
2619 107
TL
2620
XX
SSSSSS EEEEEE
All delete
No range
Next JOB# (max.=20)
ST TL
2630,2631,2632 XXYY
0
TL
– 32 –
Page 34
[JOB#2641]
MESSAGE TEXT PROGRAMMING
X: Message No. = 1~87
Message
No.
Description MRS
1 Registration error ENTRY ERROR 2 Misoperation error MISOPERATION
3
Desired code is not programmed yet.
NO RECORD
4 Paper empty PAPER EMPTY 5 Secret code error SECRET CODE 6 (reserved) 7 Memory is full MEMORY FULL 8 (reserved) 9 (reserved)
10 Stock is empty OUT OF STOCK 11
Compulsory of pushing the ST key
SBTL COMPUL.
12 Compulsory of tendering TEND COMPUL. 13 (reserved) 14 (reserved) 15 (reserved) 16 (reserved) 17 (reserved) 18 (reserved) 19 (reserved) 20 (reserved) 21 (reserved) 22 Cashier changing error CASHIER ERR. 23 Cashier entry error ENTRY ERR CA 24 (reserved) 25 (reserved) 26 (reserved) 27 (reserved) 28 (reserved) 29 (reserved) 30 (reserved)
31
Compulsory of non-add code entry
# COMPULSORY
32
The cashier key is not pushed or inserted.
NOT ASSIGNED
33
The clerk key is changed in the transaction
NOT CHANGE
34 Overflow limitation OVER LIMIT. 35 The open price entry is inhibited. INH. OPEN PR 36 The unit price entry is inhibited. INH. UNIT PR
37
The direct non-tendering finalization after previous tender entry is inhibited.
NOT NON-TEND
38
Service interruption during Validation printing
P.OFF. IN VP
39 (reserved) 40 (reserved) 41 (reserved) 42 (reserved)
Message
No.
Description MRS
43 (reserved) 44 (reserved) 45 (reserved) 46 (reserved) 47 (reserved) 48 (reserved) 49 (reserved) 50 (reserved) 51 (reserved) 52 (reserved) 53 (reserved) 54 (reserved) 55 (reserved) 56 (reserved) 57 (reserved) 58 (reserved) 59 (reserved) 60 (reserved) 61 (reserved) 62 (reserved) 63 (reserved) 64 (reserved) 65 (reserved) 66 (reserved) 67 REG Buffer full BUFFER FULL 68 (reserved) 69 (reserved) 70 (reserved) 71 (reserved) 72 EFT ERROR EFT ERROR 73 EFT BREAK EFT BREAK 74 (reserved) 75 (reserved) 76 Closed drawer error CLOSE DRAWER 77 (reserved) 78 (reserved) 79 (reserved) 80 (reserved) 81 Enter secret code ENTR SECRET# 82 IR sending SEND 83 IR receiving RECEIVE 84 IR send success SEND OK 85 IR reserve success RECEIVE OK 86 IR communication error COM. ERROR 87 IR data format error DATA ERROR 88 IR time out error TIME OUT 89 IR (zaurus) cancel CANCEL
Amessage is 12 characters Characters can be entered by using character keys or numeric keys.
the key entery sequence for entering one character by numeric keys is as follows: XXX → 00 key XXX: Character code (3 digits) Please refer to section 3
Important Note: Change of Message text under this programming
requires installation of optional ER-01/02 RA RAM chip and creation of File Group No. 16.
2641
Character key
XX
Message No.
No change
ST TL
– 33 –
Page 35
[JOB#2644]
GUIDANCE TEXT PROGRAMMING FOR EASY PROGRAMMING
XX: Guidance No. = 1~132 Characters can be entered by using character keys or numeric keys.
the key entery sequence for entering one character by numeric keys is as follows: XXX → 00 key XXX: Character code (3 digits) Please refer to section 3
1 text max. 12 characters
No. MRS JOB No.
1 DEPT PRICE #1110 2 DEPT FUNC. #2110 3 DEPT TAXABLE #2111 4 DEPT HALO #2112 5 DEPT TEXT #2114 6 DEPT COM. GRP #2115 7 DEPT GROUP #2116 8 DEPT DRCTKEY #2119
9 PLU ASG.DEPT #1200 10 PLU PRICE #1210 11 PLU BASE QTY #1211 12 PLU STCK ADD #1220 13 PLU STCK SUB #1221 14 PLU STCK OVW #1222 15 PLU FUNCTION #2210 16 PLU TAXABLE #2211 17 PLU TEXT #2214 18 PLU COM. GRP #2215 19 PLU DRCT KEY #2219 20 LINK PLU #2220 21 SET PLU #2221 22 PLU CODE RNG #2230 23 PLU FUNC RNG #2231 24 PLU STTS RNG #2232 25 PLU COM RNG #2235 26 RATE PRGRAM #1310 27 MISC KEY PGM #2311 28 FNC KEY HALO #2312 29 MDIAKEY HALO #2322 30 % HALO #2313 31 FUNC TEXT #2314 32 MISC KEY PGM #2315 33 MISC KEY PGM #2316 34 MDIA KEY PGM #2320 35 MDIAKEY HALO #2321 36 CSR CODE PGM #1500 37 CSR NAME PGM #1514 38 CSR PGM #2510 39 DATE PROGRAM #2610 40 TIME PROGRAM #2611 41 MCHN NO. PGM #2612 42 CC NO. PGM #2613 43 LOGOTEXT PGM #2614 44 VP,TRY FEED #2615 45 OPT FEATURE #2616
No. MRS JOB No.
46 DRAWER ALERM #2617 47 HOURLYREPORT #2619 48 STACK REPORT #2620 49 SECRET(TEXT) #2630 50 SECRET(X1Z1) #2631 51 SECRET(X2Z2) #2632 52 MESSGE TEXT #2641 53 GUID TEXT #2644 54 TAX RATE #2711 55 PRICE #1110/#1210 56 ENTER DEPT# #1200/#2230 57 SIGN (–) #2111-A/#2211-A/#2311-A 58 SIGN (+) #2232-A 59 TAXABLE1: YES #2111-F/#2211-F/#2311-F 60 TAXABLE1: NO #2232-F 61 TAXABLE2: YES #2111-E/#2211-E/#2311-E 62 TAXABLE2: NO #2232-E 63 TAXABLE3: YES #2111-D/#2211-D/
#2311-D 64 TAXABLE3: NO #2232-D 65 VAT: YES 66 VAT: NO 67 PRT CSR: YES #2110-A 68 PRT CSR: NO 69 VP COMPL: YES #2110-B/#2320-E 70 VP COMPL: NO 71 SIF #2110-E 72 SICS 73 NORMAL 74 DELETE #2210-C 75 OPEN&PREST #2110-G/#2231-C 76 PRESET 77 OPEN 78 INHIBITED 79 HALO(EXP.) #2112/#2312/#2322 80 HALO(AMOUNT) #2321 81 HALO(RATE) #2313 82 COM. GRP #2115/#2215/#2235 83 GROUP #2116 84 BASE Q’TY #2118 85 STOCK(ADD) #1220 86 STOCK(SUB) #1221 87 STOCK(OVER) #1222 88 RATE #1310 89 ITEM #2315 90 ST #2316 91 EFT CMPL #2320-A 92 EFT NONCMPL 93 FOOTER: YES #2320-B 94 FOOTER: NO 95 # CMPL #2320-C 96 # NONCMPL 97 DUE DISABLE #2320-D 98 DUE ENABLE 99 DRW OPEN: YES #2320-J
100 DRW OPEN: NO 101 TND CMPL: YES #2320-K 102 TND CMPL: NO 103 TND INH.
2644
Character key
XX
Guidance No.
No change
ST TL
– 34 –
Page 36
No. MRS JOB No. 104 ENTER PLU# #2220/#2221 105 ENT.CSR CODE #1500 106 ENT.CSR NO 107 ENT.DRW# #2510 108 G.C. COPY: YES 109 G.C. COPY: NO 110 VAT SFT STAT 111 VAT SFT NOT 112 ENT.DEPT# #1110/#2110/#2111/
#2112/#2114/#2116 113 ENT.KEY# #2119/#2219 114 ENT.FUNC# #1310/#2311/#2312/
#2322/#2313/#2314/
#2315/#2316/#2320/
#2321 115 #2320/#2321 116 ENT.POS.CODE #2614 117 ENTER TAX NO #2710/#2711 118 ENT.TAX RATE 119 LOWER TAX 120 ENTER MSG NO #2641
121
(FIXED DATA) The message for "Fixed"
or "Not used" data 122
ENTER [00] KEY For changing character
key layout. 123 PC-LINK SEND #0996 124 PC-LINK RCV. #0998 125 ZAURUS RCV. #1996 126 ONL T. NO. #6110 127 ONL MODEM #6111 128 ONL BAUDRATE #6112 129 ONL CODE #6113 130 ONL TIMER #6114
Important Note: Change of Guidance text under this programming
requires installation of optional ER-01/02 RA RAM chip and creation of File Group No. 17.
[JOB#2711]
TAX RATE PROGRAMMING
* DEPRESSION OF THE ST KEY AT FOLLOWING POINTS PER-
FORM A TAX TABLE DELETE OPERATION. A: Tax programming A
Tax1 1 Tax2 2 Tax3 3
Y: Sign y
+ 0 –1
xxx.xxxx: Rate = 0.0000~100.0000% LOWER TAX LIMITATION max. 999.99 (This is invalid in VAT system.)
MRS = 0
2711 YXXX.XXXX
A
Declaration of TAX TAX rate
XXXXX
Lower tax limit for add tax.
When lower tax limit is 0.
0
✽
0
TL
TL
– 35 –
Page 37
[JOB#2900]
<CAUTION>
(This JOB must be performed at X2/Z2 mode position.) AUTO KEY SETTING
(Auto key function)
• This machine has [AUTO] key which can be programmed by the
following key-sequence.
• When [AUTO] key is depressed, the machine works the same as
the programmed key-sequence programed. <Example> Mode switch ⇓ (X2/Z2)
(REG)
(X2/Z2)
(REG)
2900
(Free key)AUTO
Max.25
TL AUTO2 AUTO3
AUTO4
AUTO5
AUTO
AUTO2 AUTO3
AUTO4
AUTO5
Delete
2900 AUTO PLU1
100
DEPT2 AUTO
TL
Key entry R/J Display Comment
AUTO PL000001 *1.10
DEPT02 *1.00
PL0000001 same as entryPLU1
1.10
1 10 100 DEPT02
1.10
same as entry1 same as entry0 same as entry0 same as entryDEPT2
2900
AUTO2
PLU1
100
DEPT2
AUTO2 TL
Key entry R/J Display Comment DEPT 1 DEPT01 DEPT01
1.10
100 CHANGE
0.00
same as entry1 same as entry0 same as entry0 same as entryTL
AUTO 2
*1.00
***TOTAL *1.00
C
ASH *1.00
CHANGE *0.00
10
1
– 36 –
Page 38
3. Character assig nmen t me th od
The ER-A460/A470 has two kinds of method at character assign­ment. One is to use alphabetic assigned key and other one is to use ten keys one is to use ER-01RK.
∼ Using alphabetic assignment method ∼
Push alphabetic
Repeat
TL
Programming key layout
1 ER-A460
2 ER-A470
* When the ‘SHIFT’ key is depressed, this character can be preset with small character.
(SHIFT)
123
456
789
0
$
BACK
SPACE
(SPACE)
(DC) A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
ST
TL
(SHIFT)
(DC) ST
123
456
789
000
CL
(DEL)
( ) ( )
BACK
SPACE
><
{}
Pt
1234567890
@!#$^&()%
?
[]!!
?
GHIJKL
MN
OPQR
S
TU
V
W
X
Y
Z
A
B
E
DF
C
(SPACE) (SPACE) (SPACE) (SPACE) (SPACE)
=
-
+
;
:
/
000 TL
!
ß
§
¤
Ø
Æ
Ç
£
Ω
Ψ
Υ
Π
Λ
∆Γ
Θ
≡
Σ
Φ
.
,
– 37 –
Page 39
3 ER-01RK * Ten Key/CL key input by remote control key
Ten key function is set to the remote control key for use other than text input. Keys to be used and their corresponding keys on the ECR
Keys on the remote control Key on the ECR
0, 1 ∼ 9 0, 1 ∼ 9
[00] [00] (←) [X], [@/FOR] (→) [ . ]
[ . ] [ . ] [ST] [SBTL] [CL] [CL]
If a remote control key other than the above is pressed in a case other than character input, it is invalid. (the key input is not ac­cepted.)
[TL] key is not provided on the remote control. (After completion of setting, press [TL] key on the ECR.)
The remote control keys can be used only in PGM1/PGM2 modes. For the remote control key layout, refer to the separate sheet.
* The following key marks show the following functions:
Used as:
Keys Normal mode Character entry mode
& key Left cursor key . key Right cursor key
(BS) —
Back space key
(CL)
Clear key Clear key
1 !
       
       
Numeric key
       
       
Numeric key
2 @
3 # 4 $
5 %
6 + 7 &
8 *
9 (
0 )
(SPC) /
—
A space key or the character key("/")
(00)
It used to go into the character entry mode.
—
(SML)
—
used for entering letters in lower case.
(SHIFT)
—
used for entering the right side letter.
(DC)
—
used for entering characters in double size.
(ST)
) key used for kimination after
one item programming
(BS) (CL)( )
1
2
3
4
$#@
!
5
6
7
8
*
&
+
%
9
0
)(-
?
=
?
A
{
B
}
C
[]
D
EFGH
( )
I
JK
L
MNO
P
Q
R
S
T
U
V
W
X
YZ
£
¢ßÇ
Pt
!
§
!!
( ) ( )
Æ
( ) ( )
Ø
;:
( ) ( )
( )
( )
/
(00)
(ST)(DC)(SHIFT)(SML)
ER-01RK
X
(SPC)
@
( )
×
( )
·
– 38 –
Page 40
* General instructions for programming alphanumeric characters
using the ER-01RK This programming remote keyboard allows you to program various
items instead of using the keyboard of the cash register. The basic instruction for programming with the remote keyboard is the same as the one with the keyboard of the register. In this part, the method for programming alphanumeric characters is de­scribed.
Note: Both PGM1 and PGM2 modes are available for this pro-
gramming.
Procedure
*
1 Letters of alphabets "A" through "Z" are possible to be entered
in lower case or in upper case. By default, the upper-case letter mode is selected. To enter the character in lower case, press the (SML) key before you enter the character. The SML lamp lights up. To return to the upper-case letter mode, press the (SML) key again.
Example: To enter "aA", do the following:
*
2 Characters are possible to be entered in single size or in dou-
ble size. By default, the single-size character mode is se- lected. To enter the character in double size, press the
(DC) key before you enter the character. The DC lamp lights
up. To return to the single-size character mode, press the
(DC) key again.
Example: To enter " ", do the following:
*
3 Each character key has two levels. For example, with the
A { key, you can enter "A" or "{". Under the normal condi- tion, the left side letter is selected. To use the right side letter, press the (SHIFT) key just before you press a key.
Example: To enter "Aa[", do the following:
*
4 "( )", "( )", "( ~ )", "( )", "( )", "( )", "( )", and "( )" are
used only for combination with a character key. If the combina­tion is unavailable, only a character key is entered.
Example: To enter "Ä", do the following:
To enter "ä", do the following:
(SHIFT)(DC)(SML)
To enter th e character in the current case
To enter th e character in the cur r ent size
*1 *2 *3
To enter in the left side letter
One of the ( ), ( ), ( ), ( ), ( ), ( ), ( ), ( ) keys
*4
To use key combination
A character key
To enter next character
A {
(SML)
A {
(SML)
aA
A
(SML) (DC)
A {
(SML)
A {
(DC)
A {
(SML)
A {
(SHIFT)
A { C {
(SHIFT)
; ( ) A {
(SML) (SHIFT)
; ( ) A {
– 39 –
Page 41
4 Using ten key of ECR
Note: 00 key is used to enter each 3 digit alpha code.
00XXX
3 digits Repeat
TL
CODE TABLE FOR ALPHA DESCRIPTOR PROGRAMMING
CODE CHARACTER
001 á 002 â 003 ê 004 î 005 ì 006 í 007 ô 008 ó 009 û 010 ú 011 œ 012 ü 013 ú 014 ö 015 ó 016 Λ 017 Ψ 018 Γ 019
⋅⋅
020 Ω 021 ∆ 022 Θ 023 Ξ 024 Π 025 Σ 026 ϒ 027 Φ 028 029 Ú 030 031 Ó 033 ! 034 " 035 # 036 $ 037 % 038 & 039 ’ 040 ( 041 ) 042 * 043 + 044 ,
CODE CHARACTER
045 – 046 . 047 / 048 0 049 1 050 2 051 3 052 4 053 5 054 6 055 7 056 8 057 9 058 : 059 ; 060 < 061 = 062 > 063 ? 064 @ 065 A 066 B 067 C 068 D 069 E 070 F 071 G 072 H 073 I 074 J 075 K 076 L 077 M 078 N 079 O 080 P 081 Q 082 R 083 S 084 T 085 U 086 V 087 W
CODE CHARACTER
088 X 089 Y 090 Z 091 Ä 092 Ö 093 Ü 094 ^ 095 _ 096 ‘ 097 a 098 b 099 c 100 d 101 e 102 f 103 g 104 h 105 i 106 j 107 k 108 l 109 m 110 n 111 o 112 p 113 q 114 r 115 s 116 t 117 u 118 v 119 w 120 x 121 y 122 z 123 { 124 | 125 } 126 β 127 128 !! 129 1 130 2
CODE CHARACTER
131 3 132 4 133
1
⁄
2
134
F
T
135 ← 136 → 137 Ä 138 \ 139 e 140 d 141 F 142 T 143 ↓ 144 ç 145
o
146 ¿ 147 Ù 148 à 149 Æ 150 φ 151 Å 152 ¤ 153 é 154 è 155 Pt 156 ¡ 157 Ñ 158 ò 159 £ 177 Á 178 Í 180
A 181 a 182 E 183 e 184 I 185 i 186 U 187 u 188
189 192 193
CODE CHARACTER
194 195 196 197 198 199 200 201 203 ‰ 204 d
−
205 ‡ 206 § 208 P 209 ç 210 ë 211 † 212 ç 213 ¡ 214 ÿ 215 u
•
216 æ 217
∨
218 å 219 © 224 * 225 § 226 ∅ 227
∧
228 ↑ 229 ] 230 [ 231 232 ä 233 ö 234 ü 235 æ 236 å 237 É 238 ñ 253 DC
U
´´
O
´´
c
N
,
n
,
c
G
S
G
,
<
g
K
,
k
,
L
,
l
,
´´
DC: DOUBLE CODE
Fig. 7-2
– 40 –
Page 42
CHAPTER 3. OP X/Z, X1/Z1,X2/Z2 MODE
The following categories of reports can be printed by the ECR.
1) OP X/Z reports (individual clerk reports)
2) X1/Z1 reports (Daily sales total X and Z reports)
3) X2/Z2 reports (Periodic total X and Z reports) To print reports, use the following key entry sequence
JOB# Range is required
Reading
Resetting
TL
MODE *1
OP X/Z X1/Z1 X2/Z2 F-read
*
3 DATA FOR REPORT NAME X Z X1 Z1 X2 Z2 X1 *4 JOB# READING NOTE GENERAL FFFF 00 — DEPT/GROUP FFF10 — IND. GROUP FF 12 GROUP No. GROUP TOTAL FF 13 — PLU BY RANGE FFFF 20 PLU CODE
*
2 PLU BY DEPT FF 21 DPT CODE PLU STOCK F 24 PLU CODE
*
2 PLU ZERO SALES FF 27 ALL PLU PRICE CATEGORY FF 29 PRICE
*
2 TRANSACTION FF 30 — TL-ID FF31 — ALL CASHIER COMMISSION SALES FF 32 — ALL CASHIER FFFF 50 — IND. CASHIER FFFFFF 51 — HOURLY (ALL) FF 60
HOURLY (RANGE) F 60
*
2 DAILY NET FFF70 STACKED REP FFFF 90
* 1 X1: Daily X report Z1: Daily Z report
X2: Periodic X report Z2: Periodic Z report
Stop of printing reports: The printing of all reports can be stopped by the following operation.
Set the mode switch to "MRG" to cancel. Note) When the printing is stopped, the consecutive number or Z
counter don’t return to the original value. When Z reports, Memory is not reset. In In-line system, when Master has consolidated the data from the satellite, ECR can not stop the printing.
* 1 X1: Daily X report
X2: Periodic X report
Z1: Daily Z report Z2: Periodic Z report
* 2 PLU code range can be specified by entering the start and end
numbers according to the following procedure. When specifying a single time interval, PLU code, the start number has only to be entered.
* 3 When 2 is entered in the third digit of a job code, periodic reports
are printed. Example: Daily general report; job code 100
Periodic general report; job code 200
* 4 Reading display only
→ KEY → CL
(Display amount) (Display initialize)
KEY DEPT = DEPTn key
CID = ⊗ key Daily Net = ST key
• An individual report is printed on the receipt and journal when the
TL key is pressed.
• Pressing the decimal point key just after the enery of a job code
clears the corresponding data in the ECR. (Z report) (When printing those reports for which no Z reports can be taken, the decimal point key cannot be pressed after the entry of a job code.)
• When the decimal point key is not pressed after the entry of a job
code, the corresponding data is held in the ECR. (X report)
XXXX
All
Start No.
XXXX
End No.
– 41 –
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use