Page 1
INSTALLATION MANUAL
ER-A310
ER-A330
CODE: 00ZERA310VIME
ELECTRONIC
CASH REGISTER
MODEL ER-A310
MODEL ER-A330
SRV Key : LKGIM7113RCZZ
PRINTER: ER-A310 : CR-510
: ER-A330 : UCR-812A
(For "V" version)
CONTENTS
CHAPTER 1. GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
CHAPTER 2. LIST OF OPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
CHAPTER 3. REMOVING THE TOP CABINET (For ER-A310 & ER-A330) . . . . . . 2
CHAPTER 4. REMOVING THE BOTTOM CABINET (Only for ER-A330) . . . . . . . . 3
CHAPTER 5. REMOVING THE PRINTER UNIT (For ER-A310 & ER- A 330) . . . . . 4
CHAPTER 6. REMOVING THE MAIN PWB (For ER-A310 & ER-A330) . . . . . . . . . 4
CHAPTER 7. REMOTE DRAWER: ER-04DW (For ER-A310 & ER-A330) . . . . . . . 5
CHAPTER 8. DRAWER FIXING KIT: DKIT–8670RCZZ (Only for ER-A330) . . . . . 6
CHAPTER 9. SHIELD PLATE KIT: DKIT-8666BHZZ (Only for ER-A330) . . . . . . . . 7
CHAPTER 10. ONE HO LE CASHIER KEY KIT: DKIT-8669BHZZ
(For ER-A310 & ER-A330) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
CHAPTER 11. KEY TOP KIT: ER-11KT7/12KT7/22KT7/11DK7/51DK7
(For ER-A310 & ER-A330) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Parts marked with "! " is important for maintaining the safety of the set. Be sure to replace these parts with specified ones for
maintaining the safety and performance of the set.
This document has been published to be used
SHARP CORPORATION
for after sales service only.
The contents are subject to change without notice.
Page 2
CHAPTER 1. GENERAL
This manual describes the ER-A310/A330 disassembly procedures
and the option attachment procedures. For assembly procedures,
reverse the disassembly procedures. For attachment of options which
do not require special descriptions, descriptions are omitted.
Note for operations
• Before operation, ground the operator’s body and perform other
necessary measure against static electricity.
• During operations, disconnect the AC cord from the outlet.
• After completion of operations, connect the connectors.
• After completion of operations, be sure to perform the master
reset.
CHAPTER 2. LIST OF OPTIONS
Master reset (Al l memor y clea r)
There are two possible methods to perform a master reset.
• MRS-1
Used to clear all memory contents and return machine back to its
initial settings. return keyboard back to default. for default keyboard
layout.
Procedure-1 (with SRV key)
1) Unplug the AC cord from the wall outlet.
2) Set the MODE switch to the (SRV′) position.
3) Plug in the AC cord to the wall outlet.
4) While holding down JOURNAL FEED key, turn to (SRV) position
from (SRV′) position.
Procedure-2 (without SRV key)
1) Turn the mode switch to the (REG) position.
2) Ensure the batteries are not installed in the battery compartment
and insert the plug into the outlet.
3) The right most decimal point will blink for a few seconds.
4) The register will sound three beeps.
5) The register will display " ."
1. Sales options
No. NAME MODEL DESCRIPTIONS
1 REMOTE DRAWER ER-04DW 5B/8C
2 COIN CASE ER-58CC 5B/8C
3 COIN CASE COVER ER-03CV
4 KEY TOP KIT ER-11KT7 1 × 1 key top
ER-12KT7 1 × 2 key top
ER-22KT7 2 × 2 key top
ER-11DK7 1 × 1 dummy key
ER-51DK7 5 × 1 dummy key
2. Service optio ns
No. NAME PARTS CODE PRICE RANK DESCRIPTIONS
1 SRV KEY LKGIM7113RCZZ AK
2 MODE KEYGRIP COVER LKGIM7126RCZZ AL OP key only
3 DRIP-PROOF KEYBOARD COVER GCÇVH7126BHZZ BE
4 DRIP-PROOF MODE SWITCH COVER GCÇVH7127BHZZ BA
5 SHIELD PLATE KIT DKIT-8666BHZZ BL Only for ER-A330
6 ONE HOLE CASHIER KEY KIT DKIT-8669BHZZ BT
7 DRAWER FIXING KIT DUNT-8670BHZZ AT Only for ER-A330
3. Supplies
No. NAME PARTS CODE PRICE RANK DESCRIPTIONS
1 ROLL PAPER DPAPR1006CSZZ AR
2 INK ROLLER (ER-A310) NRÇLR6652RCZZ AZ
3 INK ROLLER (ER-A330) NRÇLR6638RCZZ AY
4 INK FOR STAMP UINK-1001CCZZ AK
– 1 –
Page 3
CHAPTER 3. REMOVING THE TOP
5
6
CABINET (For
ER-A310 & ER-A330)
1. ER-A310
1) Remove the printer cover 1 .
2) Remove the two screws 2 .
3) Remove the screw 3 and grounding wire 4 .
2
5) Remove transformer cable 5 and drawer cable 6 from the main
PWB.
1
2
4) Separate the top cabinet and the drawer unit.
Note: Transformer cable 5 and the drawer cable on the drawer
unit are connected to the main PWB on the top cabinet. Be
careful when separating them from the drawer unit.
3
4
– 2 –
Page 4
2. ER-A330
5
6
1
2
A
B
B
A
A
B
3
1) Remove the printer cover 1 .
2) Remove the three screws 2 .
3) Remove the screw 3 and grounding wire 4 .
2
2
13
2
4
5) Remove transformer cable 5 and drawer cable 6 from the main
PWB.
4) Separate the top cabinet and the bottom cabinet.
Note: Transformer cable 5 and the drawer cable on the bottom
cabinet are connected to the main PWB on the top cabinet.
Be careful when separating them from the bottom cabinet.
CHAPTER 4. REMOVING THE
BOTTOM CABINET
(Only for ER-A330)
1. ER-A330
1) Remove the top cabinet.
2) Remove the bottom cabinet 1 from the drawer unit 2 .
– 3 –
Page 5
CHAPTER 5. REMOVING THE
1
3
4
5
2
2
1
2
3
4
5
6
7
8
7
PRINTER UNIT (For
ER-A310 & ER-A330)
1. ER-A310
1) Remove the top cabinet.
2) Remove the printer cable 1 from the main PWB.
3) Remove the three screws 2 .
4) Remove the screw 3 and grounding wire 4 .
5) Remove the printer unit 5 from the top cabinet.
2
5
CHAPTER 6. REMOVING THE MAIN
PWB (For ER-A310 &
ER-A330)
4
3
1
2. ER-A330
1) Remove the top cabinet.
2) Remove the printer cable 1 from the main PWB.
3) Remove the three screws 2 .
4) Remove the screw 3 and grounding wire 4 .
5) Remove the printer unit 5 from the top cabinet.
1. ER-A310/A330
1) Remove the top cabinet.
2) Remove the printer unit.
3) Remove the following connector cables from the main PWB.
Dry battery cable 1
Pop up display cable 2
Note: The pop-up cable is fixed with the holder not to make
contact with the heat radiating plate on the main PWB. Be
careful of it when installing.
Mode switch cable 3
Keyboard cable 4
4) Remove the screw 5 and grounding wire 6 .
5) Remove the free screws 7 and main PWB 8 .
– 4 –
Page 6
CHAPTER 7. REMOTE DRAWER:
1
3
2
4
5
ER-04DW (For
ER-A310 & ER-A330)
CAUTION:
The drawer unit should be securely fitted to the supporting platform
to avoid instability when the drawer is open.
1. Outline
The ER-A310/A330 allows connection of one remote drawer ER04DW.
4) Use nippers to cot off the drawer cable split pin of the top cabinet,
and attach the top cabinet.
2. Installation procedure for ER-A310
1) Remove the top cabinet.
2) Connect the drawer cable to the drawer connector (CN16) on the
main PWB.
3) Use nippers to cut off drawer cable binding holder 1 on the trans
cover, and bind drawer cable 2 of the ER-04DW.
Screw 3 used in this case is an accessory of the ER-04DW.
3
1
2
ER-04DW
2
5) Fix ground wire 4 of the ER-04DW on the standard drawer with
screw 5 .
Screw 5 used in this case is an accessory of the ER-04DW.
3. Installation procedure for ER-A330
1) Remove the top cabinet.
2) Connect the drawer cable to the drawer connector on the main
PWB.
3) Use nippers to cut off drawer cable binding holder 1 on the
bottom cabinet, and bind drawer cable 2 of the ER-04DW.
Screw 3 used in this case is an accessory of the ER-04DW.
5
4
– 5 –
Page 7
4) Use nippers to cot off the drawer cable split pin of the top cabinet,
1
2
Draw er
A
B
3
2
1
and attach the top cabinet.
3
1
2
5) Fix ground wire 4 of the ER-04DW on the standard drawer with
screw 5 .
Screw 5 used in this case is an accessory of the ER-04DW.
CHAPTER 8. DRAWER FIXING KIT:
DKIT–8670BHZZ
(Only for ER-A330)
* For the ER-A310, standard provision.
The drawer fixing kit is used for securing the cash drawer when
installing separately from the ECR main unit.
By using two of brackets, the drawer box can be protected from
drifting especially when it is filled with coins.
2. Installation procedure
1) Fix the fixing angle bracket-A 1 to the back of the drawer with the
fixing screw 2 .
2) Remove the dust from the part to attach the fixing angle bracket-B
3 to.
3) Peel off the adhesive tape on the fixing angle bracket-B 3 .
4) Hook the fixing angle bracket-A 1 of the drawer into the abovementioned fixing angle bracket-B 3 and attach the fixing angle
bracket-B 3 to the platform.
1. Parts list KIT CODE: DKIT–8670BHZZ
No. Parts code Description
1 LANGK7612BHZZ Fixing angle bracket-A AF 1
2 LANGK7613BHZZ Fixing angle bracket-B AN 1
3 XHPSD30P08000 Screw (M3 × 8) AA 1
Price
rank
Q’ty
* To move the register, lift up the front of the drawer and pull it
frontward.
– 6 –
Page 8
CHAPTER 9. SHIELD PLATE KIT:
1
Top cabinet
2
3
CHAPTER 10. ONE HOLE CASHIER
DKIT-8666BHZZ (Only
for ER-A330)
1. Component list
1
PRICE
RANK
Q’TY
2
No. PARTS CODE DESCRIPTION
1 LCHSM6705BHZZ MAIN SHASSIS BG 1
2 TLABH7006BHZA CAUTION CARD AD 4
3 PGUMM6696BHZZ GUM LEG AE 4
4 XUPSD30P12X00 SCREW AA 4
2. Installation procedure
1) Remove the top cabinet.
2) Remove the bottom cabinet.
3) Install the shield plate 1 and attach four gum legs 3 to the
shield plate and fix them with screws 2 .
4) Replace the top cabinet.
2
2
3
KEY KIT:
DKIT-8669BHZZ
(For ER-A310 & 330)
* Standard provision for the TQ, TR, and TS versions of the ER-
A330.
1. Parts list
No. PARTS CODE DESCRIPTION
1 LKGIW7375BHZZ CASHIER KEY BODY BG 1
2 QCNCW2423BH0E CASHIER KEY
CONNECTOR (5P)
3 LKGIM7377BH01 CASHIER KEY No.1 AV 2
4 LKGIM7377BH02 CASHIER KEY No.2 AV 2
5 LKGIM7377BH03 CASHIER KEY No.3 AV 2
6 LKGIM7377BH04 CASHIER KEY No.4 AV 2
7 LKGIM7377BH05 CASHIER KEY No.5 AV 2
8 LKGIM7377BH06 CASHIER KEY No.6 AV 2
9 QCNW-7818BHZZ CASHIER KEY
CABLE (5P)
10 LANGT7602BHZZ CASHIER KEY
SWITCH ANGLE
11 XJSSD26P08000 SCREW AA 2
12 XEBSD30P08000 SCREW AA 2
13 GFTAF6922BHZZ CLERK COVER "B" AG 1
PRICE
RANK
AE 1
AN 1
AM 1
Q’ty
3
2. Installation procedure
1) Remove the top cabinet.
2) Remove the clerk cover "A" 1 from the top cabinet.
2
3
3) Solder the clerk connector (5P) 2 to the clerk switch body 3 .
– 7 –
Page 9
4) Connect the clerk key cable (5P) 4 to the clerk switch body 3 .
ER-12KT 7
ER-11KT 7
ER-22KT 7
ER-12KT 7
ER-11KT 7
ER-22KT 7
5) Attach the clerk angle 5 to the clerk switch body 3 and fix with
screw 6 (XJSSD26P08000).
6) Install the clerk switch body 3 to the clerk cover "B" 7 then
install it the top cabinet and fix with screws 8
(XEBSD30P08000).
2. Installation procedure
8
3
5
6
Main PWB.
7
CN9
4
7) Connect the clerk key cable (5P) 4 to location No. NC9 on the
main PWB.
CHAPTER 11. KEY TOP KIT
1. Outline
The ER-A310/A330 employs the following key top (option) to allow
additional installation of the key top and change in the key layout.
MODEL NAME DESCRIPTION
ER-11KT7 1 × 1 Key top
ER-12KT7 1 × 2 Key top
ER-22KT7 2 × 2 Key top
ER-11DK7 1 × 1 Dummy key
ER-51DK7 5 × 1 Dummy key
1 ER-11KT7
– 8 –
Page 10
2 ER-12KT7, ER-22KT7
Note: There are black spacers and white spacers. Refer to the figure
before for attaching them.
• Attach the black spacer to the left lower side, and the white spacer
to the right lower side.
3 ER-11DK7, ER-51DK7
– 9 –
Loading...