SHARP ER-A310 User Manual

INSTALLATION MANUAL
ER-A310
ER-A330
CODE: 00ZERA310VIME
ELECTRONIC CASH REGISTER
MODEL ER-A310
MODEL ER-A330
SRV Key : LKGIM7113RCZ Z PRINTER: ER-A310 : CR-510
: ER-A330 : UCR-812A
CONTENTS
CHAPTER 1. GENERAL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
CHAPTER 2. LIST OF OPTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
CHAPTER 3. REMOVING THE TOP CAB INE T (For ER -A310 & ER-A33 0). . . . . . 2
CHAPTER 4. REMOVING THE BOTTO M CABINET (Only fo r ER-A330). . . . . . . . 3
CHAPTER 5. REMOVING THE PRINTE R UNIT (For ER -A310 & ER-A330) . . . . . 4
CHAPTER 6. REMOVING THE MAIN PWB (For ER-A310 & ER-A330). . . . . . . . . 4
CHAPTER 7. REMOTE DRAWER: ER-0 4DW (F or ER-A3 10 & ER-A330). . . . . . . 5
CHAPTER 8. DRAWER FIXING KIT (DKIT –8633RCZZ). . . . . . . . . . . . . . . . . . . . . 6
CHAPTER 9. SHIELD PLATE KIT: DKIT-8 66 6BHZZ (O nly for ER-A330 ). . . . . . . . 7
CHAPTER 10. ONE HOLE CASHI ER KE Y KIT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
CHAPTER 11. KE Y TOP KIT : ER-11 KT 7/ 12KT7 /2 2K T7 /1 1DK 7/ 51DK7
(For ER-A310 & ER-A330). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Parts marked with "!" is important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set.
This document has been published to be used
SHARP CORPORATI ON
for after sales service only. The contents are subject to change without notice.
CHAPTER 1. GENERAL
This manual describes the ER-A310/A330 disassembly procedures and the opti on attach ment pro cedures. Fo r assembl y procedure s, re­verse the disassembly procedures. For attachmen t of option s which do not require special descriptions, descriptions are omitted.
Note for operations
Before operation, ground the operator’s body and perform other
necessary measure against static electricity.
During operations, disconnect the A C cord from the outlet.
After completion of operations, connect the connectors.
After completion of operations, be sure to perform the master reset.
Master reset (All memory clear)
There are two possible methods to perform a master reset.
MRS-1
Used to clear all memory contents and return machine back to its initial settings. retu rn keyboard back to default. for default keyboard layout.
Procedure-1 (with SRV key)
1) Unplug the AC cord from the wall outlet.
2) Set the MODE switch to the (SRV) position.
3) Plug in the AC cord to the wall outlet.
4) While holding down JOURNAL FEED key, turn to (SRV) position from (SRV) position.
Procedure-2 (without SRV key)
1) Turn the mode switch to the (REG) position.
2) Ensure the batteries are not installed in the battery compartment and insert the plug into the outlet.
3) The right most decimal point will blink for a few seconds.
4) The register will sound three beeps.
5) The register will display " ."
CHAPTER 2. LIST OF OPTIONS
1. Sales options
No. NAME MODEL DESCRIPTIONS
1 REMOTE DRAWER ER-04DW 5B/8C 2 COIN CASE ER-58CC 5B/8C 3 COIN CASE COVER ER-03CV 4 KEY TOP KIT ER-11KT7 1 × 1 key top
ER-12KT7 1 × 2 key t op ER-22KT7 2 × 2 key t op ER-11DK7 1 × 1 dummy key ER-51DK7 5 × 1 dummy key
2. Service options
No. NAME PARTS CODE PRICE RANK DESCRIPTIONS
1 SRV KEY 2 MODE KEYGRIP COVER 3 DRIP-PROOF KEYBOARD COVER 4 SHIELD PLATE KIT 5 ONE HOLE CASHIER KEY KIT 6 DRAWER FIXING KIT
LKGIM7113RCZZ LKGIM7126RCZZ GCÇVH7126BHZZ DKIT-8666BHZZ
AK AL OP key only BE BL Only for ER-A330
3. Supplies
No. NAME PARTS CODE PRICE RANK DESCRIPTIONS
1 ROLL PAPER 2 INK ROLLER (ER-A310) 3 INK ROLLER (ER-A330) 4 INK FOR STAMP
DPAPR1006CSZZ NRÇLR6652RCZZ NRÇLR6638RCZZ UINK-1001CCZZ
 1 
AR AZ AY AK
CHAPTER 3. REMOVING THE TOP
5
6
CABINET (For ER-A310 & ER-A330)
1. ER-A310
1) Remove the printer cover 1.
2
2) Remove the two screws
3) Remove the screw
.
3
and grounding wire 4.
2
5) Remove transformer cable PWB.
5
and drawer cable 6 from the main
1
2
4) Separate the top cabinet and the drawer unit. Note: Transformer cable 5 and the drawer cable on the drawer
unit are co nnected to the m ai n PW B on the top cabi ne t. Be careful when separating them from the drawer unit.
3
4
 2 
2. ER-A330
5
6
1
2
A
B
B
A
A
B
3
1) Remove the printer cover 1.
2
2) Remove the three screws
3) Remove the screw
13
2
.
3
and grounding wire 4.
2
2
4
5) Remove transformer cable PWB.
5
and drawer cable 6 from the main
4) Separate the top cabinet and the bottom cabinet.
5
Note: Transformer cabl e
cabinet are connected to the m ain PWB on the top cabinet. Be careful when separating them from the bottom cabinet.
and the drawe r cable on the bottom
CHAPTER 4. REMOVING THE
1. ER-A330
1) Remove the top cabinet.
2) Remove the bottom cabinet
BOTTOM CABINET (Only for ER-A330)
1
from the drawer unit 2.
 3 
CHAPTER 5. REMOVING THE
1
3
4
5
2
2
1
2
3
4
5
6
7
8
7
PRINTER UNIT (For ER-A310 & ER-A330)
1. ER-A310
1) Remove the top cabinet.
1
2) Remove the printer cable
3) Remove the three screws
4) Remove the screw
5) Remove the printer unit
5
from the main PWB.
2
.
3
and grounding wire 4.
5
from the top cabinet.
2
4
3
2. ER-A330
1) Remove the top cabinet.
2) Remove the printer cable
3) Remove the three screws
4) Remove the screw
5) Remove the printer unit
1
from the main PWB.
2
.
3
and grounding wire 4.
5
from the top cabinet.
CHAPTER 6. REMOVING THE MAIN
PWB (For ER-A310 & ER-A330)
1. ER-A310/A330
1) Remove the top cabinet.
2) Remove the printer unit.
1
3) Remove the following connector cables from the main PWB. Dry battery cable Pop up display cable Note: The pop-u p cable is fixed with the holder not to m ake co n-
tact with the heat radiating plate on the main PWB. Be
careful of it when installing. Mode switch cable Keyboard cable
4) Remove the screw 5 and grounding wire 6.
5) Remove the free screws
1
2
3
4
7
and main PWB 8.
 4 
CHAPTER 7. REMOTE DRAWER:
2
4
5
ER-04DW
CN16
Main PWB.
1
3
2
1
3
2
ER-04DW (For ER-A310 & ER-A330)
CAUTION: The drawer un it sho ul d b e se curely fitted to the sup po rtin g platform to avoid instability when the drawer is open.
1. Outline
The ER-A310/A330 allows connection of one remote drawer ER­04DW.
Note on the drawer connector The main PW B has no part for conn ection of the remote dra wer. In
order to connect the re mote drawer, the following pa rts must be at­tached to the main PWB.
LOCATION No.
ER-A310 ER-A330 PARTS CODE DESCRIPTION
CN16 CN16
R80 R89 Q20 Q20
DR1
IC2
JMS
CPU
QCNCM7057BHZZ VRD-RC2EY102J VS2SC3784-/-1
VP:+24V
ER-A310:Q14 ER-A330:Q21
R53
C3784
1K
R56 56K
R54 15K
L2
R55 15K
R57 ER-A310:3.3K ER-A330:4.7K
Drawer connector Resistor (1K) Transistor (2SC3784)
CN11
STANDARD DRAWER
5) Connect the drawer cable to the drawer connector on the main PWB.
1
6) Use nippers to cut off drawer cable binding holder
2
cover, and bind drawer cable
3
used in this case is an accessory of th e ER-04DW.
Screw
of the ER-04DW.
on the tran s
VP:+24V
CN16
ER-A330
Main PWB
2
C
I
U
P
C
R89 1K
Q20 C3784
OPTION DRAWER
DR2
ER-A310
Main PWB
CN16
R80 1K
C
I
C
ER-A310:R80 ER-A330:R89
1K
2
U
P
Q20 C3784
ER-A310:Q20 ER-A330:Q14 C3784
CN16
2. Installat ion proced ure for ER-A310
1) Remove the top cabinet.
2) Remove the main PWB.
3) Solder the drawer con nector CN16, the resisto r (1k) R80, and the transistor (2SC3784) Q20 to the main PWB.
4) Replace the main PWB.
7) Use nippers to cot off the drawer cable split pin of the top cab in et, and attach the top cabinet.
8) Fix ground wire
5
.
screw
5
used in this case is an accessory of th e ER-04DW.
Screw
4
of the ER-04DW on the standard d rawer with
 5 
3. Installat ion proced ure for ER-A330
1
3
2
1) Remove the top cabinet.
2) Remove the main PWB.
3) Solder the drawer con nector CN16, the resisto r (1k) R89, and the transistor (2SC3784) Q20 to the main PWB.
4) Replace the main PWB.
5) Connect the drawer cable to the drawer connector on the main PWB.
1
6) Use nippers to cut off drawer cab le b indin g ho lder
2
cabinet, and bind drawer cable
3
used in this case is an accessory of th e ER-04DW.
Screw
of the ER-04DW.
on the bo ttom
7) Use nippers to cot off the drawer cable split pin of the top cab in et, and attach the top cabinet.
4
8) Fix ground wire screw
5
.
5
used in this case is an accessory of th e ER-04DW.
Screw
of the ER-04DW on the standard d rawer with
4. Operat ion test
CHAPTER 8. DRAWER FIXING KIT
(DKIT–8633RCZZ)
The drawer fixing kit is used for securing the cash drawe r when in­stalling separately from the ECR main unit or remote drawer.
By using two of brackets, the drawer box can be protected from
5
4
CN16
Main PWB.
drifting especially when it is filled with coins.
1. Parts list KIT CODE: DKIT–8633RCZZ
No. Parts code Description Q’ty
LBRC2321RCZZ
1
XTPSD40P16000
2
XBSSD40P16000
3
XUSSD40P20000
4
XBPSD40P22000
5
XNESD4032000
6
Fixing bracket 2 Tapping s crew M4x16 4 Flat head screw M4x16
(For remote drawer) Flat head screw M4x20
(For standard drawer) Screw M4x22 4 NUT M4x32 4
2
2
 6 
2. Installation procedure
1
2
3
4
3
3
2
2
1) Turn over the drawe r bottom side and remove rub ber footing at two to locations.
2) Fasten the bracket together with the rubber footing using the p an d hand screw.
Pay attention for the installing dire ction of the bracket that the pan head screw can be inserted properly into the bracket.
Pan head screw Fixing bracket
Rubber footing
Cash drawer
Pan head s c re w
Fixing br ac ke t
Rubber footing
CHAPTER 9. SHIELD PLATE KIT:
DKIT -8666BHZZ (Only for ER-A330)
1. Component list
No. PARTS CODE DESCRIPTION Q’TY
LCHSM6705BHZZ
1
PGUMM6696BHZZ
2
TLABH7054BHZZ
3
XUBSD30P12X00
4
XUBSD30P08000
5
XJPSD30P12X00
6
XJPSD40P12X00
7
XHBSD30P08000
8
LBSHC0004AGZZ
9
2. Installation procedure
1) Remove the top cabinet.
2) Remove the bottom cabinet.
1
3) Insta ll the shield plate
2
.
screws
4) Attach four gum le gs
4
.
5) Replace the top cabinet.
to the bottom cabinet an d fix it with ???
3
to the shield p late a nd fix th em with screws
SHIELD PLATE 1 GUM LEG 4 CAUTION CARD 4 SCREW 1 SCREW 1 SCREW 1 SCREW 1 SCREW 3 CLAMP 1
Drawer bottom plate
3) Fastening on the table: Secure the fixing Bracket using the screw (Fig. 2). If the thickness of the table is less than 15mm, bore a 4.5mm hole
in the table and fasten it with the screw (XBPSD40P22000 - 4pcs.) and nut (XNESD40-32000 - 4pcs.).
Fig. 1
Fixing br ac ke t
Tapping screw
Fig. 2
 7 
CHAPTER 10. ONE HOLE CLERK
4
5
6
7
8
3
CN9
Main PWB.
KEY KIT
*
Standard provision for the TQ, TR, and TS versions of the ER­A330.
1. Component list
No. PARTS CODE DESCRIPTION Q’ty
LKGIW7375BHZZ
1
LKGIM7377BH01
2
LKGIM7377BH02
3
LKGIM7377BH03
4
LKGIM7377BH04
5
LKGIM7377BH05
6
LKGIM7377BH06
7
QCNW-7818BHZZ
8
QCNCW2423BH0E
9
LANGT7602BHZZ
10
XJSSD26P08000
11
XEBSD30P08000
12
GFTAF6922BHZZ
13
Clerk SW body 1 Clerk key 1 2 Clerk key 2 2 Clerk key 3 2 Clerk key 4 2 Clerk key 5 2 Clerk key 6 2 Clerk key cable (5P) 1 Clerk connector (5P) 1 Clerk switch angle 1 Screw 1 Screw 2 Clerk cover "B" 1
2. Installation procedure
1) Remove the top cabinet.
2) Remove the clerk cover "A"
3) Solder the clerk connector (5P)
Top cabinet
1
from the top cabinet.
2
to the clerk switch body 3.
1
7) Connect the clerk key cable (5P) PWB.
4
to location No. NC9 on the main
3. Operat ion test
2
CHAPTER 11. KEY TOP KIT
4) Connect the clerk key cable (5P)
5) Attach the clerk angle screw
6
(XJSSD26P08000).
6) Install the clerk switch body the top cabinet and fix with screws
3
4
to the clerk switch body 3.
5
to the clerk switch body 3 and fix with
3
to the clerk cover "B" 7 then install it
8
(XEBSD30P08000).
1. Outline
The ER-A460 employs the following key top (option) to allo w addi­tional installation of the key top and change in the key layout.
MODEL NAME DESCRIPTION ER-11KT7 1 × 1 Key top ER-12KT7 1 × 2 Key top ER-22KT7 2 × 2 Key top ER-11DK7 1 × 1 Dummy key ER-51DK7 5 × 1 Dummy key
 8 
2. Installation procedure
ER-22KT7
ER-12KT7
ER-11KT7
2
ER-12KT7, ER-22KT7
Note: Th ere are bl ac k spacer s and white spacers. Refer to the figure
before for attaching them.
Attach the black spacer to the left lower side, and the white spacer
to the right lower side.
ER-22KT7
1
ER-11KT7
ER-11KT7
ER-12KT7
3
ER-11DK7, ER-51DK7
 9 
Loading...