Sharp CD-ES222E User Manual

MODEL

CD-ES222E

MINI COMPONENT SYSTEM

This Quick Start Guide will help you to correctly install and oper­ate your system.

If you require any advice or assistance regarding
your Sharp product, please visit our web-site
www.sharp.co.uk/customersupport.
Customers without Internet access may telephone
08705 274277 during office hours (or [phone]
if telephoning from Ireland).

2

Remote control battery installation

0301

1

Accessories

Remote control × 1

AC power lead × 1

3

System connections

AM loop aerial

FM/AM loop aerial × 1

FM aerial

Use 2 “AA” size batteries (UM/SUM-3, R6, HP-7 or similar).
Batteries are not included.

1 Remove the battery cover.

2 Insert the batteries as shown.

3 Replace the cover.

4

Turning on your system

The first time the unit is plugged in, the
unit will enter the demonstration mode.
You will see words scroll.

Wall socket
(AC 230 - 240 V, 50 Hz)

Left speakerRight speaker

Red
Black

1 Press the X-BASS/DEMO button to

cancel the demonstration mode.

2 Press the ON/STAND-BY button to

turn the power on.

TINSEA003SJZZ
03K N HK 1

Listening to a CD (CDs)

Listening to a cassette tape

1 Press the CD button.
2 Press the OPEN/CLOSE button to open the disc tray.
3 Place the CD(s) on the disc tray, label side up.

When loading a third disc, press the DISC SKIP button to
turn the disc tray, then place the CD in the open position.

12 cm (5”)

8 cm (3”)

4 Press the OPEN/CLOSE button to close the disc tray.
5 To select the CD you want to listen to first, press one of the

1 - 3 buttons on the remote control.

6 Press the / button to start playback.

Listening to the radio

1 Open the cassette door by pushing the area marked “PUSH

EJECT

”.

2 Load a cassette into the TAPE 1 compart-

ment or TAPE 2 compartment with the
side to be played facing toward you.

TAPE 1

TAPE 2

3 Press the TAPE (1

want to listen to.

2) button to select the cassette you

4 Press the / button to start playback.

■

If trouble occurs

When this product is subjected to strong external interference
(mechanical shock, excessive static electricity, abnormal supply
voltage due to lightning, etc.) or if it is operated incorrectly, it may
malfunction.

If such a problem occurs, do the following:

1. Set the unit to the stand-by mode and turn the power on
again.

2. If the unit is not restored in the previous operation, un­plug and plug in the unit, and then turn the power on.

Note:

If neither operation above restores the unit, clear all the memory
by resetting it.

1 Press the TUNER (BAND) button repeatedly to select the

desired frequency band (FM or AM).

2 Press the TUNING/TIME ( or ) button to tune in to the

desired station.
When the TUNING/TIME button is pressed for more than 0.5
seconds, scanning will start automatically and the tuner will
stop at the first receivable broadcast station.

To receive an FM stereo transmission:

Press the TUNER (BAND) button to display the “ST” indicator.

” will appear when an FM broadcast is in stereo.

● “

FM stereo mode indicator

FM stereo receiving indicator

■

Clearing all the memory (reset)

1. Press the ON/STAND-BY button to enter the power stand­by mode.

2. Whilst pressing down the CLOCK button and the DISC
SKIP button, press the ON/STAND-BY button until
“CLEAR” appears.

Caution:

This operation will erase all data stored in memory including clock,
timer settings, tuner preset, and CD programme.

■

Maintenance

Routine maintenance is required for continued optimum perfor­mance, refer to the operation manual (page 28).