Sharp CDBA2000 User Manual

CD-BA2000H

(Continued)

Notes concerning use:

● Replace the batteries if the operating distance is reduced or if

the operation becomes erratic.

● Periodically clean the transmitter LED on the remote control

and the sensor on the main unit with a soft cloth.

● Exposing the sensor on the main unit to strong light may in-

terfere with operation. Change the lighting or the direction of

the unit.

● Keep the remote control away from moisture, excessive heat,

shock, and vibrations.

0.2 m - 6 m

(8" - 20')

SETTING THE CLOCK

ON/

STAND-BY

CLOCK

MEMORY/SET

TUNING/

TIME

( )

0:00 AM 0:00 AM 12:00

In this example, the clock is set for the 24-hour (0:00) system.

Press the ON/STAND-BY button to enter the stand-by mode.

Press the CLOCK button.

Within 5 seconds, press the MEMORY/SET button.

Press the TUNING/TIME ( or ) button to select the time

display mode.

"0:00" → The 24-hour di splay will ap pear.

(0:00 - 23:59)

"AM 0:00" → The 12-hour display will appear.

(AM 0:00 - PM 11:59)

"AM 12:00" → The 12-hour display will appear.

(AM 12:00 - PM 11:59)

● Note that this can only be set when the unit is first installed

or it has been reset (see page 29).

Press the MEMORY/SET button.

Press the TUNING/TIME ( or ) button to adjust the hour.

● Press the TUNING/TIME ( or ) button once to advance

the time by 1 hour. Hold it down to advance continuously.

● When the 12-hour display is selected, "AM" will change auto-

matically to "PM".

Press the MEMORY/SET button.

Press the TUNING/TIME ( or ) button to adjust the

minutes.

● Press the TUNING/TIME ( or ) button once to advance

the time by 1 minute. Hold it down to change the time in 5

minute intervals.

● The hour setting will not advance even if minutes advance from

"59" to "00".

Press the MEMORY/SET button.

● The clock starts operating from "0" second.

(Seconds are not displayed.)

And then the clock display will disappear after a few seconds.

To see the time display:

Press the CLOCK button.

● The time display will appear for about 5 seconds.

Note:

● The clock display will flash on and off at the push of the CLOCK

button when the AC power supply is restored after a power

failure occurs or after the AC power lead is disconnected.

If this happens, follow the procedure below to change the clock

time.

To change the clock time:

①

Press the CLOCK button.

②

Within 5 seconds, press the MEMORY/SET button.

③

Perform steps 6 - 9 above.

To change the time display mode:

①

Perform steps 1 - 2 in the section "RESETTING THE MICRO-

COMPUTER", on page 29.

②

Perform steps 1 - 9 above.

(Main unit operation)

X-BASS/

DEMO

ON/

STAND-BY

RESETTING THE MICROCOMPUTER

Reset the microcomputer under the following conditions:

● To erase all of the stored memory contents (clock and timer

settings, and tuner and CD presets).

● If the display is not correct.

● If the operation is not correct.

Press the ON/STAND-BY button to enter the stand-by mode.

Whilst pressing down the button and the X-BASS/DEMO

button, hold down the ON/STAND-BY button for at least 1

second.

● "CLEAR AL" will appear.

Caution:

● The operation explained above will erase all data stored in

memory including clock and timer settings, and tuner and CD

presets.

OPERATION MANUAL

– 6 –