NAMES OF PARTS ........................................................................................................................................................... 3
NOTES ON SCHEMATIC DIAGRAM .............................................................................................................................. 13
WAVEFORMS OF CD CIRCUIT...................................................................................................................................... 14
SCHEMATIC DIAGRAM / WIRING SIDE OF P.W.BOARD..............................................................................................18
VOLTAGE ........................................................................................................................................................................ 34
FUNCTION TABLE OF IC................................................................................................................................................ 39
REPLACEMENT PARTS LIST/EXPLODED VIEW
PACKING OF THE SET (FOR U.S.A. ONLY)
Page
SHARP CORPORATION
This document has been published to be used
for after sales service only.
The contents are subject to change without notice.
CD-BA120/125
FOR A COMPLETE DESCRIPTION OF THE OPERATION OF THIS UNIT, PLEASE REFER
TO THE OPERATION MANUAL.
IMPORTANT SERVICE NOTES (FOR U.S.A. ONLY)
BEFORE RETURNING THE AUDIO PRODUCT
(Fire & Shock Hazard)
Before returning the audio product to the user, perform the
following safety checks.
1. Inspect all lead dress to make certain that leads are not
pinched or that hardware is not lodged between the chassis
and other metal parts in the audio product.
2. Inspect all protective devices such as insulating materials,
cabinet, terminal board, adjustment and compartment covers
or shields, mechanical insulators etc.
3. To be sure that no shock hazard exists, check for leakage
current in the following manner.
* Plug the AC line cord directly into a 120 volt AC outlet.
* Using two clip leads, connect a 1.5k ohm, 10 watt resistor
paralleled by a 0.15µF capacitor in series with all exposed
metal cabinet parts and a known earth ground, such as
conduit or electrical ground connected to earth ground.
* Use a VTVM or VOM with 1000 ohm per volt, or higher,
sensitivity to measure the AC voltage drop across the
resistor (See diagram).
* Connect the resistor connection to all exposed metal parts
having a return path to the chassis (antenna, metal cabinet,
screw heads, knobs and control shafts, escutcheon, etc.)
and measure the AC voltage drop across the resistor.
VTVM
AC SCALE
1.5k ohms
10W
0.15 µ F
TO EXPOSED
TEST PROBE
METAL PARTS
CONNECT TO
KNOWN EARTH
GROUND
All check must be repeated with the AC line cord plug connection
reversed.
Any reading of 0.3 volt RMS (this corresponds to 0.2 milliamp.
AC.) or more is excessive and indicates a potential shock
hazard which must be corrected before returning the audio
product to the owner.
CD-BA120/125
SPECIFICATIONS
● General
Power source:AC 120 V, 60 Hz
Power consumption:35 W
Dimensions:Width; 10-5/8" (270 mm)
In this example, the clock is set for the 12-hour (AM 12:00) sys-
tem.
1
Press the ON/STAND-BY button to enter the stand-by mode.
2
Press the CLOCK button.
3
Within 5 seconds, press the MEMORY/SET button.
4
Press the TUNING/TIME ( or ) button to select the time
display mode.
"AM 12:00" → The 12-hour display will appear.
(AM 12:00 - PM 11:59)
"AM 0:00 " → The 12-hou r display will appear.
(AM 0:00 - PM 11:59)
"0:00" → The 24-hour d isplay will ap pear.
(0:00 - 23:59)
● Note that this can only be set when the unit is first installed
or it has been reset (see page 15).
5
Press the MEMORY/SET button.
6
Press the TUNING/TIME ( or ) button to adjust the hour.
● Press the TUNING/TIME ( or ) button once to advance
the time by 1 hour. Hold it down to advance continuously.
● When the 12-hour display is selected, "AM" will change auto-
matically to "PM".
7
Press the MEMORY/SET button.
8
Press the TUNING/TIME ( or ) button to adjust the
minutes.
● Press the TUNING/TIME ( or ) button once to advance
the time by 1 minute. Hold it down to change the time in 5
minute intervals.
● The hour setting will not advance even if minutes advance from
"59" to "00".
9
Press the MEMORY/SET button.
● The clock starts operating from "0" second.
(Seconds are not displayed.)
And then the clock display will disappear after a few seconds.
To see the time display:
Press the CLOCK button.
● The time display will appear for about 5 seconds.
Note:
● The clock display will flash on and off at the push of the CLOCK
button when the AC power supply is restored after a power
failure occurs or after the AC power cord is disconnected.
If this happens, follow the procedure below to change the clock
time.
To change the clock time:
①
Press the CLOCK button.
②
Within 5 seconds, press the MEMORY/SET button.
③
Perform steps 6 - 9 above.
To change the time display mode:
①
Perform steps 1 - 2 in the section "RESETTING THE
MICROCOMPUTER", on page 15.
②
Perform steps 1 - 9 above.
(Main unit operation)
AM 0:00AM 12:000:00
2
3
4
7
6
5
8
9
RESETTING THE MICROCOMPUTER
Reset the microcomputer under the following conditions:
● To erase all of the stored memory contents (clock and timer
settings, and tuner and CD presets).
● If the display is not correct.
● If the operation is not correct.
1
Press the ON/STAND-BY button to enter the stand-by mode.
2
While pressing down the button and the EQUALIZER/X-
BASS/DEMO button, hold down the ON/STAND-BY button for
at least 1 second.
● "CLEAR AL" will appear.
Caution:
● The operation explained above will erase all data stored in
memory including clock and timer settings, and tuner and CD
presets.
EQUALIZER
X-BASS/
DEMO
POWER
ON/
STAND-BY
CD-BA120/125
– 5 –
CD-BA120/125
MINI COMPONENT SYSTEM
Quick Guide/Guía rápida
CD-BA120
● Remote control x 1
●
Controlador remoto x 1
● 2 “AA” batteries
●
Dos pilas “AA”
Remote Sensor
Sensor remoto
2
Preparation for use /
Preparación para su uso
1
Check the supplied accessories /
Compruebe los accesorios suministrados
● FM/AM loop antenna x 1
●
Antena de cuadro de
FM/AM x 1
● Batteries are not included.
●
Las pilas no están incluidas.
8” - 20’ (0.2m - 6m)
0,2m - 6m
■ Speaker connection
■
Conexión de los altavoces
■ Antenna connection
■
Conexión de las antenas
Front speaker
(Right)
Altavoz delantero
(Derecho)
Front speaker
(Left)
Altavoz delantero
(Izquierdo)
● AM Loop Antenna
●
Antena de cuadro
de AM
● FM Antenna
●
Antena de FM
● AC 120 V, 60 Hz
●
120 V de CA, 60 Hz
Red
Rojo
■ Switching between power-on and stand-by mode
■
Cambio entre la conexión de la alimentación y el
modo de reserva
■ Remote control
■
Controlador remoto
15
15
Black
Negro
● AC power cord x 1
●
Cable de alimentación de
CA x 1
3
Listening to a CD /
Audición de discos CD
4
Listening to a tape /
Audición de una cinta
5
Listening to the radio /
Audición de la radio
6
Recording from CDs /
Grabaciones de discos CD
7
Sound control /
Control del sonido
● Label facing up
●
Etiqueta hacia arriba
■ To stop the playback
■
Para detener la reproducción
■ To stop the recording
■
Para detener la grabación
● Load the disc to be
recorded.
●
Introduzca el disco
que va a grabar.
● CD recording
starts.
●
La grabación de
CD empieza.
■ Volume
■
Volumen
<Extra bass (X-BASS)>
<Graves extra (X-BASS)>
<Pre-programmed equalizer>
<Ecualizador preprogramado>
Printed in Malaysia
Impreso en Malaysia
TINSZ0533AWZZ A9911.HK
FLAT
ROCK
POPS
JAZZ
CLASSIC
VOCAL
■ To stop the playback
■
Para detener la reproducción
TAPE 1TAPE 2
TAPE 2
FLAT (X-BASS on)
ROCK (X-BASS on)
POPS (X-BASS on)
JAZZ (X-BASS on)
CLASSIC (X-BASS on)
VOCAL (X-BASS on)
VOCAL (X-BASS off)
CLASSIC (X-BASS off)
JAZZ (X-BASS off)
POPS (X-BASS off)
ROCK (X-BASS off)
FLAT (X-BASS off)
■ Extra bass (X-BASS) / Pre-programmed equalizer
■
Graves extra (X-BASS) / ecualizador preprogramado
– 6 –
Caution on Disassembly
(B1)x4
ø3x12mm
(B1)x1
ø3x10mm
Rear
Panel
(B1)x1
ø3x10mm
Side Panel
(Right)
Side Panel
(Left)
(A1)x2
ø3x12mm
(A1)x2
ø3x12mm
Top Cabinet
Follow the below-mentioned notes when disassembling
the unit and reassembling it, to keep it safe and ensure
excellent performance:
1. Take cassette tape and compact disc out of the unit.
2. Be sure to remove the power supply plug from the wall
outlet before starting to disassemble the unit.
3. Take off nylon bands or wire holders where they need be
removed when disassembling the unit. After servicing
the unit, be sure to rearrange the leads where they were
before disassembling.
4. Take suffcient care on static electricity of integrated
circuits and other circuits when servicing.
11 CD Servo PWB1. Screw ..................... (K1) x18-6
(Note 2)2. Hook ....................... (K2) x2
12 CD Mechanism1. Hook ....................... (L1) x29-1
13
Loading Motor PWB
2. Flat Cable............... (F2) x1
2. Screw...................... (G1) x6
2. Cover ..................... (H2) x1
2.
3.
3. Socket .................... (K3) x4
2. Hook....................... (L2) x3
1. Hook....................... (M1) x59-1
PROCEDURE
open the disc tray, take out the
CD cover, and close. (Note 1)
Turn fully the lock lever in the
arrow direction.
While holding the lock lever,rotate
the cam gear until the cam gear
rib engages with the clamp lever.
Push the slide holder backward to
engage the claw with the groove
and remove it in the direction
of the arrow. ..............
DISASSEMBLY
FIGURE
(F1) x9
(J1) x6
8-3
7-3
8-1
8-5
CD-BA120/125
CD Servo
PWB
(C3) x1
Pull
Rear
Panel
(C1)x1
ø3x12mm
(D1)x3
ø3x12mm
Figure 7-1
(C4)x2
Main PWB
Figure 7-2
CD-BA120/125
CD Tray Cover
(C2) x3
1
1
2
CD Player
Unit
(C3)x1
LOCK LEVER
Note 1:
How to open the changer manually. (Fig. 7-3)
1. In this state, turn fully the lock lever in the arrow direction
through the hole on the loading chassis bottom.
2.
While holding the lock lever, rotate the cam gear anticlockwise
until the cam gear rib engages with the clamp lever.
3. After that, push forward the CD slide holder.
Note 2:
1. After removing the connector for the optical pickup from the
(Fig. 8-1)
connector, wrap the conductive aluminium foil around the
front end of the connector so as to protect the optical pickup
from electrostatic damage.
Figure 7-3
Note 3:
1. Be careful not to break the claw of the CD mechanism.
2. When fining back the cam gear assembly, let it lock by front
movement.
– 7 –
CD-BA120/125
(K3) x2
(K2) x2
(K3) x2
CD Servo
PWB
CD Player
Base
(K1)x1
ø3x8mm
(H2) x1
CLAMP LEVER
Turntable
(D1)x1
ø3x10mm
(D2)x2
Main PWB
Figure 8-1
(D1)x7
ø3x10mm
(D3)x1
Figure 8-2
CAM GEAR RIB
(D2)x2
(E1)x3
ø3x8mm
Headphones
PWB
1
(H) x2
Disc Tray
CD Player Unit
Figure 8-4
(J1) x3
2
(J1) x3
(F1)x9
ø3x10mm
Tape
Mechanism
(G1)x6
ø3x10mm
(F2)x1
Figure 8-3
Figure 8-5
Display PWB
Open
Cassette
Holder
Figure 8-6
– 8 –
Cam Gear
CD-BA120/125
CD
Mechanism
(L1) x1
Figure 9-1
CP-BA120/125
STEPREMOVAL
1Speaker1. Net ..........................(A1) x19-1
2. Duct Panel ..............(A2) x1
3. Screw...................... (A3) x49-2
(L2) x3
(L1) x1
PROCEDURE
Loading
Motor
PWB
(M1) x5
FIGURE
CP-BA120/125
(A1)x1
(A2)x1
Driver
Speaker Box
Speaker Box
Speaker
(A3)x4
ø3.5x13mm
Driver should be
pried away from
Speaker Box.
Direction of handle
Figure 9-2
Figure 9-3
– 9 –
CD-BA120/125
REMOVING AND REINSTALLING THE MAIN PARTS
TAPE MECHANISM SECTION
Perform steps 1 to 5 and 7 of the disassembly method to
remove the tape mechanism.
How to remove the record/playback and erase
heads (TAPE 2) (See Fig. 10-1)
1. Carefully remove the record/playback head and erase head
screw (A1) x 2 pcs.
How to remove the playback head (TAPE 1)
(See Fig. 10-2)
1. Carefully remove the playback head screw (B1) x 2 pcs.
How to remove the pinch roller (TAPE 1/2)
(See Fig. 10-3)
1. Carefully bend the pinch roller pawl in the direction of the
arrow <A>, and remove the pinch roller (C1) upwards.
Note:
When installing the pinch roller, pay attention to the spring
mounting position.
Erase Head
(A1)x2
Ø2 x 9mm
Figure 10-1
TAPE2
TAPE1
Record/Playback
Head
Playback
Head
How to remove the belt (TAPE 1) (See Fig. 10-4)
1. Remove the main belt (D1) x 1 pc., from the motor side.
2. Remove the FF/REW belt (D2) x 1 pc.
How to remove the belt (TAPE 2) (See Fig. 10-4)
1. Remove the main belt (E1) x 1 pc., from the motor side.
2. Remove the FF/REW belt (E2) x 1 pc.
How to remove the motor (See Fig. 10-5)
1. Remove the screws (F1) x 2 pcs., to remove the motor.
Motor
TAPE2
(B1)x2
Ø2 x 9mm
Pinch Roller
(C1)x1
FF/REW
Belt
(E2)x1
Figure 10-2
Figure 10-3
Motor
<A>
TAPE2
Main Belt
(E1)x1
Motor
TAPE1
Main Belt
(D1)x1
(F1) x2
Ø 2.6 x 5mm
– 10 –
Main Belt
TAPE1
FF/REW
Belt
(D2)x1
Figure 10-4Figure 10-5
CD MECHANISM SECTION
TAPE MECHANISM
Motor
Variable Resistor in motor
Perform steps 1, 2, 3, 9, 12 and 13 of the disassembly method
to remove the CD mechanism.
CD-BA120/125
How to remove the loading motor
(See Fig. 11-1)
1. Bend the hooks (A1) x 5 pcs., to remove the loading motor.
How to remove the pickup (See Fig. 11-2)
1. Remove the screws (B1) x 2 pcs., to remove the shaft (B2).
2. Remove the stop washer (B3) x 1 pc., to remove the gear
(B4).
3. Remove the pickup.
Note
After removing the connector for the optical pickup from the
connector wrap the conductive aluminium foil around the front
end of connector so as to protect the optical pickup from
electrostatic damage.
(B1) x2
ø2.6 x6mm
Loading Motor
(A1)x1
(A1)x2
(A1)x2
CD Base
Figure 11-1
Stop Washer
(B3) x1
MECHANISM SECTION
• Driving Force Check
Torque Meter
Play: TW-2111Tape 1: Over 80 g
• Torque Check
Torque Meter
Tape 1
Play: TW-211130 to 80 g. cm30 to 80 g.cm
Fast forward: TW-2231—70 to 180 g.cm
Rewind: TW-2231—70 to 180 g.cm
Since this CD system incorporates the following automatic
adjustment functions, readjustment is not needed when
replacing the pickup. Therefore, different PWBs and pickups
can be combined freely.
Each time a disc is changed, these adjustments are
performed automatically. Therefore, playback of each disc
can be performed under optimum conditions.
(1) Offset adjustment (The offset voltage between the head
amplifier output and the VREF reference voltage is
compensated inside the IC.)
0101Open/Close SW Low → High not functioning
0103Open/Close SW High → Low not functioning
0201Open/Close SW Low → High not functioning
0203Open/Close SW High → Low not functioning
0302Pickup-in SW is not detected
0306During Disc 1 search, Open/Close SW or Clamp SW
0307Clamp SW Low → High not functioning
0308Clamp SW High → Low not functioning
– 12 –
[Servo System Error]
[Error during close operation]
[Error during open operation]
[Error during skip operation]
or Disc SW do not change to low.
T
Stopped
CH1=500mV
CH2=200mV
DC 10:1
CH3=1V
DC 10:1
=Record Length=
Main : 100K
Zoom : 2k
DC 10:1
T
FDO
1
TE
3
EFBL
2
Smoothing : ON CH1 : 0.000V
BW : FULL
CH2 : 0.000V
CH3 : 0.00V
CH4 : 0.00V
Figure 12-2
1999/04/05 20:26:47
500ms/div
(500ms/div)
NORM:20kS/s
CH2
v/DIV
200mV
=Trigger==Filter==Offset=
Mode : SINGLE
Type : EDGE CH1
Delay : 0.0ns
Hold off : 0.2us
NOTES ON SCHEMATIC DIAGRAM
• Resistor:
To differentiate the units of resistors, such symbol as K and
M are used: the symbol K means 1000 ohm and the symbol
M means 1000 kohm and the resistor without any symbol is
ohm-type resistor. Besides, the one with “Fusible” is a fuse
type.
• Capacitor:
To indicate the unit of capacitor, a symbol P is used: this
symbol P means micro-micro-farad and the unit of the
capacitor without such a symbol is microfarad. As to
electrolytic capacitor, the expression “capacitance/withstand
voltage” is used.
(CH), (TH), (RH), (UJ): Temperature compensation
(ML): Mylar type
(P.P.): Polypropylene type
• Schematic diagram and Wiring Side of P.W.Board for this
model are subject to change for improvement without prior
notice.
CD-BA120/125
• The indicated voltage in each section is the one measured
by Digital Multimeter between such a section and the chassis with no signal given.
1. In the tuner section,
( ) indicates AM
< > indicates FM stereo
2. In the main section, a tape is being played back.
3. In the deck section, a tape is being played back.
( ) indicates the record state.
4. In the power section, a tape is being played back.
5. In the CD section, the CD is stopped.
• Parts marked with “ ” ( ) are important for
maintaining the safety of the set. Be sure to replace these
parts with specified ones for maintaining the safety and
performance of the set.
When the CD section does not operate when the objective lens of the optical pickup is dirty, this section may not operate. Clean
the objective lens, and check the playback operation. When this section does not operate even after the above step is taken, check
the following items.
Remove the cabinet and follow the trouble shooting instructions.
"Track skipping and/or no TOC (Table Of Contents) may be caused by build up of dust other foreign matter on the laser pickup
lens. Before attempting any adjustment make certain that the lens is clean. If not, clean it as mentioned below."
Turn the power off.
Gently clean the lens with a lens cleaning tissue and a small amount of isopropyl alcohol.
Do not touch the lens with the bare hand.
Using the brush in the cleaner cap, apply 1 or 2 drops of the cleaning fluid to the
brush on the CD cleaner disc which has the mark next to it.
2.
Place the CD cleaner disc onto the CD disc tray with the brush side down,then
press the play button.
3.
You will hear music for about 20 seconds and the CD player will automatically stop.
If it continuous to tum, press the stop button.
Cleaner Fluid
CAUTION
The CD lens cleaner should be effective for 30-50 operations, however if the
brushes become worn out earlier then please the cleaner disc.
If the CD cleaner brushes become very wet then wipe off any excess fluid with a soft
cloth.
Do not drink the cleaner fluid or allow it to come in contact with the eyes. In the
event of this happening then drink and / or rines with clean water and seek medical
advice.
The CD cleaner disk must not be used on car CD players or on computer CD ROM
drives.
All rights reserved.Unauthorized duplicating, broadcasting and renting this product is
Cleaner disc
When a CD cannot be played
1. "E-CD01" is displayed.
(1) Check the power to IC2 (LC78641E), the presence of the clock signal (16.93 MHz) and the status of the RESET terminal
(pin 71 on IC2).
(2) Did the pickup move to the PICKUP-IN Switch (SW4) position?
If (1) and (2) are OK, check the system microcomputer (especially the communication line with the DSP).
2. Pressing the CD operation key is accepted, butplayback does not occur.
(1) Focus-HF system check
(2) Tracking system check
(3) Spin system check
(4) PLL system check
(5) Others
– 35 –
CD-BA120/125
(1) Focus-HF system check
Although a CD is inserted and the cover is closed, "NO
DISC" is displayed.
Press the OPEN/CLOSE switch (SW1) without inserting a
disc, and try starting the playback operation.
1. Did the pickup move to the PICKUP-IN Switch (SW4)
position?
Yes
2. Does the focus (lens) move up and down?
(Waveform drawing 36-1).
Yes
3. Is the laser lit?
No
No
No
Stopped
CH1=500mV
DC 10:1
T
FDO
1
TDO
3
Smoothing : ON CH1 : 0.000V
BW : FULL
CH2 : 0.0V
CH3 : 0.000V
CH4 : 0.00V
CH3=500mV
DC 10:1
=Record Length=
Main : 100K
Zoom : 2K
NORM:20kS/s
=Trigger==Filter==Offset=
Mode : AUTO
Type : EDGE CH1
Delay : 0.0ns
Hold off : 0.2us
Figure 36-1
Sled motor (M2)
Check the focus peripheral circuit.
Check the laser diode driver Q3 peripheral circuit.
500ms/div
(500ms/div)
CH1
v/DIV
500mV
Yes
4. Is the turntable rotating?
When a disc is loaded, start playback operation.
1. Is focus servo activated? (Waveform drawing 36-2)
Yes
2. Does DRF change from "L" to "H"?
No
Is the disc rotating?
Yes
3. Is the HF waveform normal? (Waveform drawing 36-3)
Stopped
1
T
2
CH1=500mV
DC 10:1
FDO
DRF
CH2=10V
DC 10:1
CH3=1V
DC 10:1
500ms/div
(500ms/div)
NORM:20kS/s
No
No
No
Spindle motor (M1).
Pins 1~11 on IC1
Check the laser diode driver Q3 peripheral circuit.
Focus error circuit (pins 20 and 21 on IC1)
No
Check the spin system.
If the disc is spinning and a HF waveform is generated,
DRF will go H.
If the level is not normal, check around pins 27~29 on IC1.
TE
3
-3div-1div0div+1div+3div
Smoothing : ON CH1 : 0.000V
BW : FULL
CH Position To
CH2 : 0.0V
CH3 : 0.00V
CH4 : 0.00V
=Record Length=
Main : 100K
Zoom : 2K
Figure 36-2
CH2
Position
0.20div
=Trigger==Filter==Offset=
Mode : AUTO
Type : EDGE CH1
Delay : 0.0ns
Hold off : 0.2us
– 36 –
Figure 36-3
Vp-p=1.0V~1.3V
0.5mV/div,0.5µsec/div
(2) Tracking system check
Check the TE waveform at pin 18 on IC1.
If the waveform shown in Figure 37-1 appears and soon after
NO DISC appears.
No
Yes
CD-BA120/125
The tracking servo is not activated.
Check the peripheral circuits at pins 18 and 19 on IC1, pin 23 on
IC2, and CNS1A/B.
"Initialization" is possible, but play is not possible.
No
"Initialization" is not possible.
(3) Spin system check
Yes
A normal jump operation cannot be completed or the beginning of
the track cannot be found.
Check the around pin 23 on IC2.
Data cannot be read. Check the VCO-PLL system.
Stopped
CH1=10V
DC 10:1
TE
2
DRF
T
1
=Filter==Offset=
Smoothing : ON CH1 : 0.0V
BW : FULL
T
CH2=1V
DC 10:1
CH2 : 0.00V
CH3 : 0.00V
CH4 : 0.00V
=Record Length=
Main : 100K
Zoom : 2K
100ms/div
(100ms/div)
NORM:100kS/s
=Trigger=
Mode : NORMAL
Type : EDGE CH1
Delay : 2.924ms
Hold off : 0.2us
Figure 37-1
Press the OPEN/CLOSE switch without inserting a disc, and
then try starting the play operation.
1. The turntable rotates a little. (Waveform drawing 37-2)
No
2. The turntable doesn't rotate.
Yes
The spin driver circuit is OK.
Check around pin 25 on IC2, pins 15 and 16 on IC3, and CNS3A/B.
Stopped
CH1=200mV
DC 10:1
T
FDO
2
SPDO
1
=Filter==Offset=
Smoothing : ON CH1 : 0.000V
BW : FULL
T
CH2=500mV
DC 10:1
CH2 : 0.000V
CH3 : 0.00V
CH4 : 0.00V
=Record Length=
Main : 100K
Zoom : 2K
1999/04/07 09:51:15
500ms/div
(500ms/div)
NORM:20kS/s
=Trigger=
Mode : NORMAL
Type : EDGE CH2
Delay : 2.924ms
Hold off : 0.2us
– 37 –
Figure 37-2
CD-BA120/125
(4) PLL system check
When a disc is loaded, start play operation.
The HF waveform is normal, but the TOC data cannot be
read.
Check the PDO waveform. (Figure 38-1)
Check around pins 1~6 on IC2.
(5) Others
The HF waveform is normal and the time is displayed
normally, but no sound is produced. Or the sound has
dropouts.
Is pin 35 (C2F) on IC2 "L"?
Yes
No
Stopped
CH1=500mV
DC 10:1
PDO1
3
4
PDO2
T
FDO
1
Smoothing : ON CH1 : 0.000V
BW : FULL
CH2 : 0.0V
CH3 : 0.00V
CH4 : 0.00V
CH3=1V
DC 10:1
=Record Length=
Main : 100K
Zoom : 2K
1999/04/05 17:33:17
CH4=1V
500ms/div
(500ms/div)
DC 10:1
NORM:20kS/s
=Trigger==Filter==Offset=
Mode : AUTO
Type : EDGE CH2
Delay : 0.0ns
Hold off : 0.2us
CH1
v/DIV
500mV
Figure 38-1
There are too many error flags on a damaged disc which
makes error correction impossible.
1. When playing at normal speed
Check the peripheral circuit at pin 37 (DOUT) on IC2 and
the waveform (Figure 38-2).
If both 1. and 2. are OK.
DOUT
CH1=2V
DC 10:1
T
1999/04/07 09:25:28
500ns/div
(500ns/div)
NORM:200MS/s
Stopped
T
1
Check again using a known good disc.
=Filter==Offset=
Smoothing : ON CH1 : 0.00V
BW : FULL
CH2 : 0.00V
CH3 : 0.00V
CH4 : 0.00V
=Record Length=
Main : 1K
Zoom : 100
Figure 38-2
=Trigger=
Mode : NORMAL
Type : EDGE CH1
Delay : 2.887ms
Hold off : 0.2us
– 38 –
FUNCTION TABLE OF IC
IC1 VHiLA9235M/-1: Servo Amp. (LA9235M)
CD-BA120/125
130FIN1VCC
REF
2
FIN2
REF
3FIN3
REF
FIN4
4
REF
5REF1
REF
6VREF
TESI
7LDS
8LDD
9VEE
10LDOF
11ODRV
12AGON
13EFBL
14TESO
15
APC
ODRV
AGCON
LPF
LA9235M
REF
REF
ODRV
REF
REF
AGCON
PH
BH
PH/BH
REF
LPF
REF
LPF
REF
REF
REF
ODRV
REF
29
RFSW
28 RF-
27
RF
26 N/C
25 PH
24 BH
23 N/C
22 RFEV
21 FE20 FE
19 TE18 TE
17 HFL
16
TES
IC2 VHiLC78641E-1: Servo/Signal Control (LC78641E)
IC2 VHiLC78641E-1: Servo/Signal Control (LC78641E) (1/2)
Pin No.
1PDO1Output–For PULLPhase-comparison output terminal for built-in VOC control.
2PDO2Output–Phase-comparison output terminal for built-in VOC control.
3VVSS––Ground terminal for built-in VCO.
4PCKISTAI–Resistor terminal for setting the PDO output current.
5VVDD––Power terminal for built-in VCO.
6FRAI–Resistor terminal for setting the VCO frequency range.
7HFLInput–Mirror detection signal input terminal.
8SLCISTAI–For slice level control
9SLCOOutput–Control output.
10EFMINInput–EFM signal input terminal.
11*JITTVOutputUnfixedJitter detection/monitor terminal.
12JITTCOutput–Jitter detection/adjustment terminal.
13BHInput–BH signal input terminal. A/D input.
14PH(RFENV)Input–PH signal or RFENV signal input terminal. A/D input.
15FEInput–FE signal input terminal. A/D input.
16TEInput–TE signal input terminal. A/D input.
17VREFInput–VREF signal input terminal. A/D input.
18ADAVDD––AD for servo, D/A power terminal.
19ADAVSS––AD for servo, D/A ground terminal.
20*PHREFOutput(1/2VDD)PH reference output terminal. D/A output.
21*BHREFOutput(1/2VDD)BH reference output terminal. D/A output.
22TBLOOutput(1/2VDD)Output terminal for tracking balance. D/A output.
23TDOOutput(1/2VDD)Output terminal for tracking control. D/A output.
24FDOOutput(1/2VDD)Output terminal for focus control. D/A output.
25SPDOOutput(1/2VDD)Output terminal for spindle control. D/A output.
26SLDOOutput(1/2VDD)Output terminal for sled control. D/A output.
27*FGInput–FG signal input terminal. (When not used,connect to 0V)
28LASEROutputLLASER ON/OFF control terminal.
29CONT1In/OutputInput modeGeneral purpose input/output terminal 1.
30CONT2In/OutputInput modeGeneral purpose input/output terminal 2.
31CONT3In/OutputInput modeGeneral purpose input/output terminal 3.
32CONT4In/OutputInput modeGeneral purpose input/output terminal 4.
33CONT5In/OutputInput modeGeneral purpose input/output terminal 5.
34*PCKOutputHClock monitor terminal for EFM data replay. 4.3218MHz as phase clock.
35*C2FOutputHC2 flag output terminal.
36VDD––Power terminal of digital system.
37*DOUTOutputLOutput terminal of digital OUT. (EIAJ format)
38*FSXOutputL
39*EFLGOutputLC1,C2 correct monitor terminal.
40TESTInput–Input terminal for test. Surely connected to 0V.
41*EMPHIn/OutputInput mode
42*MUTELOutputHMute output terminal for L channel.
43*MUTEROutputHMute output terminal for R channel.
Terminal Name
Input/Output
Setting in Reset
Rough servo : OFF, phase servo : ON.
Output terminal of synchronous signal of 7.35kHz divided from quartz oscillation.
Emphasis terminal. After resetting, it is configured as an input terminal. It can be controlled
from the outside. It is also becomes a emphasis monitor terminal under command control.
In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.
Function
Resistance connection terminal for current adjustment of
SLCO output.
Controlled with serial data command
from microcomputer. When not used,
set it as the input terminal
open it by connecting to 0V, or set it
as the output terminal and open it.
and
– 40 –
CD-BA120/125
IC2 VHiLC78641E-1: Servo/Signal Control (LC78641E) (2/2)
Pin No.
44LVDD––L channelPower terminal for L channel.
45LCHOOutput1/2VDDD/A converter L channel output terminal.
46LVSS––Ground terminal for L channel. Surely connected to 0V.
47RVSS––R channelGround terminal for R channel. Surely connected to 0V.
48RCHOOUTPUT1/2VDDD/A converter R channel output terminal.
49RVDD––Power terminal for R channel.
50XVDD––For quartzPower terminal for quartz oscillation.
51XINInputOscillationoscillationGround terminal of 16.9344MHz quartz oscillation.
52XOUTOutputOscillation
53XVSS––Ground terminal for quartz oscillation. Surely connected to 0V.
54ASLRCKInput–For antiL/R clock input terminal. (When not used,connect to 0V)
55ASDACKInput–shock modeBit clock input terminal. (When not used,connect to 0V)
56ASDFINInput–L/R channel data input terminal. (When not used,connect to 0V)
57*LRSYOutputLFor digitalL/R clock output terminal.
58*DATACKOutputLdata outputBit clock output terminal.
59*DATAOutputLL/R channel data output terminal.
60*16MOutputClock output16.9344MHz output terminal.
61*SFSYOutputLOutput terminal of synchronous signal of subcode frame.
62*SBSYOutputLOutput terminal of synchronous signal of subcode block.
63*PWOutputLOutput terminal of subcodes P,A,R,S,T,U and W.
64SBCKInput–Clock input terminal to read subcode. (When not used,connect to 0V)
65CEInput–ForChip enable signal input terminal.
66CLInput–
67DIInput–interfaceData input terminal.
68DOOutputLData output terminal.
69INTOutputHInterruption signal output terminal.
70WRQOutputHInterruption signal output terminal.
71RESInput–Reset input terminal of LC78640. When turning on power, set it at "L".
72DRFOutputLFocus ON detection terminal.
73VDD5V––Power terminal for microcomputer interface.
74VSS––Ground terminal of digital system. Surely connected to 0V.
75CONT6In/OutputInput modeGeneral purpose input/output terminal 6.
77*V/ *POutputHMonitor output terminal for automatic switch of rough servo/phase control.
78*FSEQOutputL
79DEFECTIn/OutputInput mode
80*EFMOOutputUnfixed
Terminal Name
Input/Output
Setting in Reset
It drops when subcode stand by.
microcomputer
"H" for rough servo, and "L" for phase servo.
Output terminal synchronous signal detection. "H" is output when synchronous
detected by EFM signal matches synchronous signal
Defect terminal. After resetting, it is configured as an input terminal. It can be controlled
from the outside. It also becomes a defect monitor terminal under command control
EFM signal output terminal.
Data transmission clock input terminal.
Function
Controlled with serial data command
from microcomputer. When not used,
set it as the input terminal
open it by connecting to 0V, or set it
as the output terminal and open it.
internally generated.
and
signal
In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.
Be sure to supply the same potential to each power terminal. (VVDD,ADAVDD,VDD,LVDD,RVDD,XVDD)
Terminal witch is controlled by the power terminal (VDD5V) for a microcomputer interface :
CE (65pin), CL (66pin), DI (67pin), DO (68pin), INT (69pin), WRQ (70pin), RES (71pin), DRF (72pin),
CONT6 (75pin), CONT7 (76pin)
– 41 –
CD-BA120/125
IC701 RH-iX0336AWZZ: System Microcomputer (IX0336AW) (1/2)
P17M–BUSYInputCOMMUNJCATE TO MPEGU COM M_BUSY
27ANI6NO USEInputGND
28ANI5SPEANA 2InputSPEANA DATA INPUT 16 KHz
29ANI4SPEANA 1InputSPEANA DATA INPUT 1 KHz
30ANI3SPEANA 0InputSPEANA DATA INPUT 63 KHz
31-33ANI2-ANI0KEY2-KEY0InputKEY INPUT
34AVDDAVDD—ANALOG VDD
35AVREFAVREF—ANALOG REF VOLTAGE
36INTP3SYS STOPInputSYSTEM STOP INPUT
37*P02SPRLYOutputSPEAKER OUTPUT RELAY CONTROL
38INTP1NO USEDInputGND
39INTP0REMOCONInputREMOCON INPUT
40VssVSS—GROUND VOLTAGE
41P74SMUTEOutputSYSTEM MUTE CONTROL
42P73T_SOL_BOutputTAPE2 SOLENOID CONTROL
43P72T_SOL_AOutputTAPE1 SOLENOID CONTROL
44P71T_MOTOROutputTAPE MOTOR CONTROL
45P70TIMER LEDOutputTIMER LED CONTROL
46VDDVDD—(+) POWER SUPPLY
47*P127AC RLY_CONTOutputAC RELAY CONTROL
48P126SPRLYOutputSPEAKER OUTPUT RELY CONTROL
49P125SP DETInputSPEAKER OUTPUT DETDCTION
50P124T1 RUNInputTAPE1 RUN PULSE INPUT
51P123T2 RUNInputTAPE2 RUN PULSE INPUT
52P122CD CLAMP SWIntputCD CHANGER CLAMP SWITCH
53P121PLAY SW_AInputPLAY SWITCH FOR T1
Function
In this unit, the terminal with asterisk mark (*) is (open) terminal which is not connected to the outside.
– 42 –
IC701 RH-iX0336AWZZ: System Microcomputer (IX0336AW) (2/2)
CD-BA120/125
Port NameTerminal NamePin No.Input/Output
Function
54P120PLAY SW_BInputPLAY SWITCH FOR T2
55P119PPAInputTAPE2 A–SIDE FULL PROOF
56P118FPBInputTAPE2 B_SIDE FULL PROOF
57P117MIC SWInputMIC SWITCH
58*P116KARAOKE LATCHOutputKARAOKE LATCH
59*P115DISTOUTOutputDISTINATION OUTPUT
60FIP39SPNInputTUNER SPAN CHANGE
61*-62*FIP38-FIP37 NO USEInputOPEN
63*-66*FIP36-FIP33 P22-P19OutputFL DISPLAY DRIVER
67*-70*FIP32-FIP29 P18-P15OutputFL DISPLAY DRIVER
If there are no indications for the electrolytic capacitors, error is ± 20%.
NOTE:
Parts marked with “” are important for maintaining the safety of the set.
Be sure to replace parts with specified ones for maintaining the safety and performance of the set.
Resistors
VRD ....................... Carbon-film type
VRS........................ Carbon-film type
VRN ....................... Metal-film type
VR • • MF............... Cylindrical type (without lead wire)
VR • • MN ............... Cylindrical type (without lead wire)
VR • • TV................ Square type (without lead wire)
VR • • TQ ............... Square type (without lead wire)
VR • • CY ............... Square type (without lead wire)
VR • • CZ ............... Square type (without lead wire)
VR • • • • • • • • • J .. The 13th character represents error.
("J" ±5%, "F" ±1%, "D" ±0.5%.)
If there are no indications for other parts, the resistors are ±5%
carbon-film type.
CD-BA120/125
PARTS CODENO.PARTS CODE
PRICE
RANK
DESCRIPTIONNO.
CD-BA120/125
INTEGRATED CIRCUITS
IC1VHILA9235M/-1J AQ Servo Amp.,LA9235M
IC2VHILC78641E-1J AV Servo/Signal Control,LC78641E
IC3VHIM63001FP-1J AX Focus/Tracking/Spin/Sled Driver,
IC101VHIAN7345K/-1J AM Playback and Record/Playback
IC301VHITA7358AP-1J AG FM Front End,TA7358AP
IC302VHILC72131/-1J AP PLL (Tuner),LC72131
IC303VHILA1832S/-1J AN FM IF Det./FM Mpx./AM IF,
IC601VHILC75341/-1J AM Audio Processor,LC75341
IC701RH-IX0336AWZZJ AX System Microcomputer,
IC704VHIKIA7042AP1J AC Reset,KIA7042AP
IC901VHILA4282//-1J AM Power AMP.,STK40204
IC902VHIKIA7810AP1J AF Voltage Regulator,KIA7810AP
IC904VHIKIA7805P-1J AF Voltage Regulator,KIA7805P
M63001FP
Amp.,AN7345K
LA1832S
IX0328AW
TRANSISTORS
Q1VSKTC3203Y/-1J AC Silicon,NPN,KTC3203 Y
Q2VSKRC102M//-1J AC Digital,NPN,KRC102 M
Q3VSKTA1266GR-1J AB Silicon,PNP,KTA1266 GR
Q101VSKTA1266GR-1J AB Silicon,PNP,KTA1266 GR
Q102,103VSKRC104M//-1J AC Digital,NPN,KRC104 M
Q104~107VS2SC1845F/-1J AC Silicon,NPN,2SC1845 F
Q108~111VS2SC3331//-1J AB Silicon,NPN,2SC3331
Q112VSKTA1266GR-1J AB Silicon,PNP,KTA1266 GR
Q113VSKRC104M//-1J AC Digital,NPN,KRC104 M
Q114VSKTC3203Y/-1J AC Silicon,NPN,KTC3203 Y
Q302VSKTC3194Y/-1J AD Silicon,NPN,KTC3194 Y
Q360VSKTA1266GR-1J AB Silicon,PNP,KTA1266 GR
Q601,602VS2SC3331//-1J AB Silicon,NPN,2SC3331
Q701VSKRC107M//-1J AC Digital,NPN,KRC107 M
Q702,703VS2SC3331//-1J AB Silicon,NPN,2SC3331
Q704,705VSKTA1271Y/-1J AC Silicon,PNP,KTA1271 Y
Q706VSKTA1273Y/-1J AE Silicon,PNP,KTA1273 Y
Q707VSKRC102M//-1J AC Digital,NPN,KRC102 M
Q901,902VSKRC102M//-1J AC Digital,NPN,KRC102 M
Q903VSKTD2026//-1J
Q904VSKTA1266GR-1J AB Silicon,PNP,KTA1266 GR
DIODES
D21,22VHDDS1SS133-1J AB Silicon,DS1SS133
D93VHDDS1SS133-1J AB Silicon,DS1SS133
D301,302VHD1SS133//-1J AA Silicon,1SS133
D305,306VHD1SS133//-1J AA Silicon,1SS133
D701~705VHD1SS133//-1J AA Silicon,1SS133
D707~711VHD1SS133//-1J AA Silicon,1SS133
D901,902VHD1SS133//-1J AA Silicon,1SS133
D907~910VHDRL203F//-1J AC Silicon,RL203F
D911~917VHD1N4004S/-1J AB Silicon,1N4004S
D918VHD1SS133//-1J AA Silicon,1SS133
LED722VHP4204SRT7-1J AD LED,Red,4204SRT7
VD301VHCSVC348S/-1J AK Variable Capacitance,SVC348S
VD302,303VHCSVC211C/-1J AG Silicon,SVC211C,Variable Cap
ZD61VHEDZ3R9BSB-1 J AC Zener,3.9V,DZ3.9BSB
ZD902VHEDZ300BSB-1 J AB Zener,30V,DZ300BSB
ZD903VHEMTZJ6R2A-1 J AA Zener,6.2V,MTZJ6.2A
FILTERS
BF301RFILR0008AWZZJ AE Band Pass Filter
CF303RFILF0124AFZZJ AD FM IF,10.7 MHz
CF351RFILF0003AWZZJ AK FM IF
CF352RFILA0009AWZZJ AE AM IF
TRANSFORMERS
! PT801RTRNP0305AWZZ J AZ Power
T301RCILB0065AWZZ J AC FM, OSC
T302RCILI0017AWZZJ AB FM IF
T303RCILA0052AWZZ J AE AM Tracking
T306RCILB0058AWZZ J AC AM OSC
T351RCILI0019AWZZJ AD AM IF
PRICE
RANK
DESCRIPTION
COILS
L61VP-XHR82K0000J AC 0.82 µH
L62VP-XH2R2K0000J AB 2.2 µH,Choke
L103VP-DH101K0000J AB 100 µH,Choke
L104VP-MK331K0000J AB 330 µH,Choke
L312RCILR0056AWZZ J AB FM RF
L351,352VP-DH101K0000J AB 100 µH,Choke
L701VP-DH101K0000J AB 100 µH,Choke
C6VCEAZA1AW107M J AB 100 µF,10V,Electrolytic
C7VCEAZA1CW106M J AC 10 µF,16V,Electrolytic
C8VCKYTV1HB104K J AB 0.1 µF,50V
C11RC-EZY474AF0JJ0.47 µF,6.3V,Electrolytic
C12VCKYTV1HB104K J AB 0.1 µF,50V
C13VCKYTV1HB103K J AA 0.01 µF,50V
C14VCKYTV1EF334Z J AB 0.33 µF,25V
C16VCCSPA1HL6R0J J AA 6 pF,50V
C17VCKYTV1HB472K J AA 0.0047 µF,50V
C18VCCCTV1HH3R0C J AA 3 pF (CH),50V
C19VCEAZA1AW107M J AB 100 µF,10V,Electrolytic
C20,21VCKYTV1HB104K J AB 0.1 µF,50V
C22VCKYTV1HB101K J AA 100 pF,50V
C23VCKYTV1HB473K J AA 0.047 µF,50V
C24VCEAZA1HW225M J AB 2.2 µF,50V,Electrolytic
C25VCKYTV1HB104K J AB 0.1 µF,50V
C26VCKYTV1HB473K J AA 0.047 µF,50V
C27VCKYTV1HB104K J AB 0.1 µF,50V
C28VCEAZA1AW476M J AB 47 µF,10V,Electrolytic
C29,30VCKYTV1HB104K J AB 0.1 µF,50V
C31VCEAZA1AW107M J AB 100 µF,10V,Electrolytic
C34VCTYBT1EF223Z J AA 0.022 µF,25V
C38,39VCEAZA1CW106M J AC 10 µF,16V,Electrolytic
C40VCKYTV1HB152K J AA 0.0015 µF,50V
C41VCEAZA1AW107M J AB 100 µF,10V,Electrolytic
C42VCCSTV1HL680J J AA 68 pF,50V
C43VCKYTV1HB152K J AA 0.0015 µF,50V
C44VCKYTV1HB104K J AB 0.1 µF,50V
C45VCEAZA1AW107M J AB 100 µF,10V,Electrolytic
C46VCKYTV1EF223Z J AA 0.022 µF,25V
C47VCEAZA1CW107M J AC 100 µF,16V,Electrolytic
C49,50VCEAZA1CW107M J AC 100 µF,16V,Electrolytic
C51VCEAZA1AW476M J AB 47 µF,10V,Electrolytic
C52VCTYPA1CX103K J AA 0.01 µF,16V
C53VCKYTV1HB102K J AA 0.001 µF,50V
C54VCEAZA1AW476M J AB 47 µF,10V,Electrolytic
C55VCKYTV1HB103K J AA 0.01 µF,50V
C56VCEAZA0JW337M J AC 330 µF,6.3V,Electrolytic
C64RC-EZY474AF0JJ0.47 µF,6.3V,Electrolytic
C71VCKYTV1HB101K J AA 100 pF,50V
C72VCKYTV1HB103K J AA 0.01 µF,50V
C73~78VCKYTV1HB101K J AA 100 pF,50V
C80VCKYTV1HB104K J AB 0.1 µF,50V
C81~83VCKYTV1EF223Z J AA 0.022 µF,25V
C101VCKZPA1HF473Z J AA 0.047 µF,50V
C102,103VCKYMN1HB561K J AA 560 pF,50V
C104,105VCKYMN1HB181K J AA 180 pF,50V
C106,107VCKYMN1HB561K J AA 560 pF,50V
C108RC-EZD107AF1AJ AC 100 µF,50V,Electrolytic
C112~115VCKYMN1HB331K J AA 330 pF,50V
C116,117VCEAZA1EW107M J AB 100 µF,25V,Electrolytic
C118,119VCTYPA1EX333K J AA 0.033 µF,25V
C120,121VCKYMN1HB561K J AA 560 pF,50V
C122,123VCEAZA1HW105M J AB 1 µF,50V,Electrolytic
C126,127VCKYMN1HB271K J AA 270 pF,50V
C128,129VCEAZA1EW226M J AB 22 µF,25V,Electrolytic
C130,131VCKZPA1HF223Z J AA 0.022 µF,50V
C132,133VCTYMN1CX332K J AA 0.0033 µF,16V
C134,135VCEAZA1EW476M J AB 47 µF,25V,Electrolytic
C136VCEAZA1EW226M J AB 22 µF,25V,Electrolytic
C137VCTYMN1EF223Z J AA 0.023 µF,25V
– 1 –
CD-BA120/125
NO.PARTS CODE
C138VCEAZA1AW227M J AC 220 µF,10V,Electrolytic
C139VCEAEA1HW335M J AB 3.3 µF,50V,Electrolytic
C140VCQPKA2AA822J J AA 0.0082 µF,100V,Polypropylene
C141VCQYKA1HM393K J AB 0.039 µF,50V,Mylar
C142VCEAZA1EW476M J AB 47 µF,25V,Electrolytic
C145~147VCKYMN1HB102K J AA 0.001 µF,50V
C148VCKZPA1HF473Z J AA 0.047 µF,50V
C301VCKYMN1HB102K J AA 0.001 µF,50V
C303VCCCMN1HH100J J AA 10 pF (CH),50V
C304VCTYMN1CY103N J AA 0.01 µF,16V
C305VCCCMN1HH4R7C J AA 4.7 pF (CH),50V
C306VCTYMN1EF223Z J AA 0.022 µF,25V
C307VCEAZA1CW106M J AC 10 µF,16V,Electrolytic
C308VCCSMN1HL4R7C J AA 4.7 pF,50V
C309VCKYMN1HB102K J AA 0.001 µF,50V
C310VCCCMN1HH150J J AA 15 pF (CH),50V
C311VCCSMN1HL180J J AA 18 pF,50V
C312VCTYMN1EF223Z J AA 0.022 µF,25V
C313VCCCMN1HH220J J AA 22 pF (CH),50V
C314,315VCTYMN1CX472K J AA 0.0047 µF,16V
C316VCTYMN1EF223Z J AA 0.022 µF,25V
C317VCKYMN1HB102K J AA 0.001 µF,50V
C318VCKYMN1HB101K J AA 100 pF,50V
C320VCTYBT1EF223Z J AA 0.022 µF,25V
C323VCTYMN1EF223Z J AA 0.022 µF,25V
C324VCCUMN1HJ3R9K J AA 3.9 pF (UJ),50V
C330VCCUMN1HJ150J J AA 15 pF (UJ),50V
C331VCKZPA1HF473Z J AA 0.047 µF,50V
C332VCTYMN1EF223Z J AA 0.022 µF,25V
C334VCCUMN1HJ270J J AA 27 pF (UJ),50V
C335VCKYMN1HB561K J AA 560 pF,50V
C342VCTYMN1EF223Z J AA 0.022 µF,25V
C350,351VCTYMN1EF223Z J AA 0.022 µF,25V
C352VCEAZA1CW106M J AC 10 µF,16V,Electrolytic
C353,354VCTYMN1EF223Z J AA 0.022 µF,25V
C355VCCSMN1HL220J J AA 22 pF,50V
C356VCKYMN1HB102K J AA 0.001 µF,50V
C357VCEAZA1HW225M J AB 2.2 µF,50V,Electrolytic
C358VCEAZA1HW105M J AB 1 µF,50V,Electrolytic
C361VCTYMN1EF223Z J AA 0.022 µF,25V
C362VCEAZA1HW335M J AB 3.3 µF,50V,Electrolytic
C363VCTYMN1EF223Z J AA 0.022 µF,25V
C364VCEAZA1CW106M J AC 10 µF,16V,Electrolytic
C365VCKZPA1HF223K J0.022 µF,50V
C366VCKYMN1HB102K J AA 0.001 µF,50V
C367,368VCEAZA1HW105M J AB 1 µF,50V,Electrolytic
C369VCCUMN1HJ270J J AA 27 pF (UJ),50V
C370~372VCEAZA1HW105M J AB 1 µF,50V,Electrolytic
C373,374VCTYPA1CX153K J AA 0.015 µF,16V
C380VCEAZA1CW106M J AC 10 µF,16V,Electrolytic
C381VCCCMN1HH120J J AA 12 pF (CH),50V
C382VCCCMN1HH150J J AA 15 pF (CH),50V
C384VCKYMN1HB102K J AA 0.001 µF,50V
C385VCTYMN1CY103N J AA 0.01 µF,16V
C386VCKYMN1HB331K J AA 330 pF,50V
C387VCTYMN1EF223Z J AA 0.022 µF,25V
C391VCEAZA1CW476M J AB 47 µF,16V,Electrolytic
C392VCKYMN1HB102K J AA 0.001 µF,50V
C393VCEAZA1HW105M J AB 1 µF,50V,Electrolytic
C394VCEAZA1CW476M J AB 47 µF,16V,Electrolytic
C395VCTYMN1EF223Z J AA 0.022 µF,25V
C396VCEAZA1AW107M J AB 100 µF,10V,Electrolytic
C397VCTYMN1EF223Z J AA 0.022 µF,25V
C398VCEAZA1AW107M J AB 100 µF,10V,Electrolytic
C399VCTYMN1EF223Z J AA 0.022 µF,25V
C601,602VCKYMN1HB102K J AA 0.001 µF,50V
C603VCEAZA1EW226M J AB 22 µF,25V,Electrolytic
C604VCEAZA1EW107M J AC 100 µF,25V,Electrolytic
C605VCKZPA1HF223Z J AA 0.022 µF,50V
C606VCEAZA1HW226M J AB 22 µF,50V,Electrolytic
C607,608VCEAZA1HW106M J AB 10 µF,50V,Electrolytic
C609~612VCQYKA1HM104K J AB 0.1 µF,50V,Mylar
C613,614VCTYPA1CX272K J AA 0.0027 µF,16V
C617,618VCEAZA1HW105M J AB 1 µF,50V,Electrolytic
C623~630VCEAZA1HW105M J AB 1 µF,50V,Electrolytic
C701VCTYBT1EF223Z J AA 0.022 µF,25V
C702RC-EDZ227AF1AJ AC 220 µF,10V,Electrolytic
C703VCCSMN1HL150J J AA 15 pF,50V
C704VCCSMN1HL180J J AA 18 pF,50V
C705VCEAZA1AW107M J AB 100 µF,10V,Electrolytic
C707,708RC-EDZ105AF1H J AB 1 µF,50V,Electrolytic
C710VCEAZA1EW476M J AB 47 µF,25V,Electrolytic
PRICE
RANK
DESCRIPTION
NO.
C711,712RC-EZD106AF1CJ AC 10 µF,16V,Electrolytic
C713VCEAZA1HW104M J AB 0.1 µF,50V,Electrolytic
C714VCTYMN1CY103N J AA 0.01 µF,16V
C715VCEAZA1HW335M J AB 3.3 µF,50V,Electrolytic
C716VCTYBT1EF223Z J AA 0.022 µF,25V
C717VCEAZA1HW106M J AB 10 µF,50V,Electrolytic
C718VCTYMN1EF223Z J AA 0.022 µF,25V
C719RC-EZD476AF1EJ AB 47 µF,25V,Electrolytic
C903,904VCKYPA1HB102K J AA 0.001 µF,50V
C905VCKZPA1HF223Z J AA 0.022 µF,50V
C906VCEAZA1EW476M J AB 47 µF,25V,Electrolytic
C907VCEAZA1EW107M J AB 100 µF,25V,Electrolytic
C908,909VCQYKA1HM823K J AC 0.082 µF,50V,Mylar
C910VCEAZA1EW107M J AB 100 µF,25V,Electrolytic
C911VCKZPA1HF223Z J AA 0.022 µF,50V
C914,915VCEAZA1EW477M J AD 470 µF,25V,Electrolytic
C916,917VCQYKA1HM473K J AB 0.047 µF,50V,Mylar
C918VCKYPA1HB221K J AA 220 pF,50V
C919VCEAZA1HW106M J AB 10 µF,50V,Electrolytic
C933VCCSPA1HL680J J AA 68 pF,50V
C934VCQYKA1HM473K J AB 0.047 µF,50V,Mylar
C935VCEAZA1EW226M J AB 22 µF,25V,Electrolytic
C938VCEAZA1EW476M J AB 47 µF,25V,Electrolytic
C939,940VCQYKA1HM104K J AB 0.1 µF,50V,Mylar
C943VCEAZA1EW476M J AB 47 µF,25V,Electrolytic
C944VCKZPA1HF223Z J AA 0.022 µF,50V
C945VCQYKA1HM104K J AB 0.1 µF,50V,Mylar
C946VCEAZW1VW228M J AH 2200 µF,35V,Electrolytic
C947VCEAZW1EW338M J AG 3300 µF,25V
C950~953VCQYKA1HM473K J AB 0.047 µF,50V,Mylar
C954VCEAZA1HW107M J AC 100 µF,50V,Electrolytic
C955~957VCEAZA1HW476M J AB 47 µF,50V,Electrolytic
C958,959VCEAZA1HW107M J AC 100 µF,50V,Electrolytic
C960,961VCEAZA1HW226M J AB 22 µF,50V,Electrolytic [125 Only]
PRICE
RANK
DESCRIPTIONPARTS CODE
RESISTORS
VRD-MN2BD000C J AA 0 ohm,Jumper,ø1.4×3.5mm,Ivory
R3VRS-TV2AB104JJ AA 100 kohm,1/10W
R4VRS-TV2AB103JJ AA 10 kohm,1/10W
R5VRS-TV2AB393JJ AA 39 kohms,1/10W
R6VRS-TV2AB273JJ AA 27 kohms,1/10W
R7VRS-TV2AB682JJ AA 6.8 kohms,1/10W
R8VRS-TV2AB331JJ AA 330 ohms,1/10W
R10VRS-TV2AB273JJ AA 27 kohms,1/10W
R11VRS-TV2AB123JJ AA 12 kohms,1/10W
R12,13VRS-TV2AB681JJ AA 680 ohms,1/10W
R14VRS-TV2AB122JJ AA 1.2 kohms,1/10W
R15VRS-TV2AB103JJ AA 10 kohm,1/10W
R16VRD-ST2CD103JJ AA 10 kohm,1/6W
R17VRD-ST2CD102JJ AA 1 kohm,1/6W
R19VRD-ST2CD470JJ AA 47 ohms,1/6W
R20VRS-TV2AB221JJ AA 220 ohms,1/10W
R21,22VRS-TV2AB471JJ AA 470 ohms,1/10W
R25VRD-ST2CD103JJ AA 10 kohm,1/6W
R35VRD-ST2CD102JJ AA 1 kohm,1/6W
R38VRD-ST2CD271JJ AA 270 ohms,1/6W
R39VRD-ST2CD471JJ AA 470 ohms,1/6W
R40VRS-TV2AB122JJ AA 1.2 kohms,1/10W
R42VRS-TV2AB124JJ AA 120 kohms,1/10W
R43VRS-TV2AB224JJ AA 220 kohms,1/10W
R44VRD-ST2CD102JJ AA 1 kohm,1/6W
R45VRS-TV2AB122JJ AA 1.2 kohms,1/10W
R46VRS-TV2AB102JJ AA 1 kohm,1/10W
R47VRD-ST2EE3R3JJ AA 3.3 ohms,1/4W
R48VRS-TV2AB682JJ AA 6.8 kohms,1/10W
R50VRS-TV2AB470JJ AA 47 ohms,1/10W
R51~54VRS-TV2AB683JJ AA 68 kohms,1/10W
R55,56VRD-ST2CD683JJ AA 68 kohms,1/6W
R58VRD-ST2CD221JJ AA 220 ohms,1/6W
R71~78VRD-ST2CD102JJ AA 1 kohm,1/6W
R79VRS-TV2AB155JJ AA 1.5 Mohms,1/10W
R80VRD-ST2CD105JJ AA 1 Mohm,1/6W
R81,82VRS-TV2AB222JJ AA 2.2 kohms,1/10W
R83,84VRS-TV2AB103JJ AA 10 kohm,1/10W
R88VRS-TV2AB682JJ AA 6.8 kohms,1/10W
R94,95VRS-TV2AB103JJ AA 10 kohm,1/10W
R101,102VRD-MN2BD103J J AA 10 kohm,1/8W
R103VRD-MN2BD472J J AA 4.7 kohms,1/8W
R104,105VRD-MN2BD102J J AA 1 kohm,1/8W
R106,107VRD-MN2BD222J J AA 2.2 kohms,1/8W
VRS-TV2AB000JJ AA 0 ohm,Jumper,1.25×2mm,Green
– 2 –
CD-BA120/125
PARTS CODENO.PARTS CODE
R108,109VRD-MN2BD332J J AA 3.3 kohms,1/8W
R110VRD-MN2BD473J J AA 47 kohms,1/8W
R111,112VRD-MN2BD472J J AA 4.7 kohms,1/8W
R113VRD-MN2BD473J J AA 47 kohms,1/8W
R114,115VRD-ST2CD102JJ AA 1 kohm,1/6W
R116,117VRD-ST2CD560JJ AA 56 ohms,1/6W
R118,119VRD-MN2BD104J J AA 100 kohm,1/8W
R120,121VRD-MN2BD392J J AA 3.9 kohms,1/8W
R122,123VRD-MN2BD562J J AA 5.6 kohms,1/8W
R124,125VRD-MN2BD333J J AA 33 kohms,1/8W
R126VRD-MN2BD683J J AA 68 kohms,1/8W
R127,128VRD-MN2BD682J J AA 6.8 kohms,1/8W
R129,130VRD-MN2BD392J J AA 3.9 kohms,1/8W
R131,132VRD-MN2BD152J J AA 1.5 kohms,1/8W
R133,134VRD-MN2BD101J J AA 100 ohm,1/8W
R135,136VRD-MN2BD103J J AA 10 kohm,1/8W
R137VRD-MN2BD153J J AA 15 kohms,1/8W
R138VRD-ST2CD153JJ AA 15 kohms,1/6W
R139VRD-ST2EE181JJ AA 180 ohms,1/4W
R140VRD-ST2CD103JJ AA 10 kohm,1/6W
R141VRD-MN2BD103J J AA 10 kohm,1/8W
R142,143VRD-ST2CD224JJ AA 220 kohms,1/6W
R144VRD-MN2BD473J J AA 47 kohms,1/8W
R145VRD-ST2CD472JJ AA 4.7 kohms,1/6W
R146VRD-RT2HD820JJ AA 82 ohms,1/2W
R147VRD-MN2BD473J J AA 47 kohms,1/8W
R148VRD-MN2BD223J J AA 22 kohms,1/8W
R149VRD-ST2CD4R7J J AA 4.7 ohms,1/6W
R157VRD-ST2EE101JJ AA 100 ohm,1/4W
R302VRD-MN2BD100J J AA 10 ohm,1/8W
R309VRD-ST2CD103JJ AA 10 kohm,1/6W
R311VRD-MN2BD104J J AA 100 kohm,1/8W
R313VRD-MN2BD333J J AA 33 kohms,1/8W
R314VRD-ST2CD220JJ AA 22 ohms,1/6W
R316VRD-MN2BD472J J AA 4.7 kohms,1/8W
R322VRD-MN2BD681J J AA 680 ohms,1/8W
R323VRD-MN2BD683J J AA 68 kohms,1/8W
R325VRD-MN2BD473J J AA 47 kohms,1/8W
R327VRD-MN2BD330J J AA 33 ohms,1/8W
R336VRD-MN2BD103J J AA 10 kohm,1/8W
R350VRD-MN2BD272J J AA 2.7 kohms,1/8W
R351VRD-MN2BD562J J AA 5.6 kohms,1/8W
R352VRD-MN2BD102J J AA 1 kohm,1/8W
R353VRD-MN2BD271J J AA 270 ohms,1/8W
R355VRD-MN2BD332J J AA 3.3 kohms,1/8W
R356VRD-MN2BD102J J AA 1 kohm,1/8W
R357VRD-ST2CD474JJ AA 470 kohms,1/6W
R358VRD-ST2CD392JJ AA 3.9 kohms,1/6W
R359VRD-MN2BD182J J AA 1.8 kohms,1/8W
R360VRD-MN2BD472J J AA 4.7 kohms,1/8W
R361,362VRD-MN2BD103J J AA 10 kohm,1/8W
R363,364VRD-MN2BD822J J AA 8.2 kohms,1/8W
R365VRD-MN2BD103J J AA 10 kohm,1/8W
R372~374VRD-MN2BD102J J AA 1 kohm,1/8W
R375VRD-ST2CD471JJ AA 470 ohms,1/6W
R376VRD-MN2BD102J J AA 1 kohm,1/8W
R377VRD-MN2BD473J J AA 47 kohms,1/8W
R378VRD-MN2BD102J J AA 1 kohm,1/8W
R379VRD-MN2BD222J J AA 2.2 kohms,1/8W
R380VRD-MN2BD152J J AA 1.5 kohms,1/8W
R381VRD-MN2BD103J J AA 10 kohm,1/8W
R382VRD-ST2EE151JJ AA 150 ohms,1/4W
R383VRD-MN2BD562J J AA 5.6 kohms,1/8W
R384VRD-ST2CD562JJ AA 5.6 kohms,1/6W
R385VRD-MN2BD562J J AA 5.6 kohms,1/8W
R386VRD-ST-2CD223J J AA 22 kohms,1/6W
R387VRD-ST2CD562JJ AA 5.6 kohms,1/6W
R388VRD-MN2BD392J J AA 3.9 kohms,1/8W
R393VRD-MN2BD102J J AA 1 kohm,1/8W
R395VRD-MN2BD473J J AA 47 kohms,1/8W
R601,602VRD-ST2CD331JJ AA 330 ohms,1/6W
R603,604VRD-ST2CD182JJ AA 1.8 kohms,1/6W
R607,608VRD-MN2BD222J J AA 2.2 kohms,1/8W
R609,610VRD-ST2CD103JJ AA 10 kohm,1/6W
R615,616VRD-ST2CD392JJ AA 3.9 kohms,1/6W
R617VRD-ST2CD332JJ AA 3.3 kohms,1/6W
R618VRD-MN2BD332J J AA 3.3 kohms,1/8W
R625VRD-ST2CD223JJ AA 22 kohms,1/6W
R702~704VRD-MN2BD102J J AA 1 kohm,1/8W
R705~717VRD-ST2CD102JJ AA 1 kohm,1/6W
R719~721VRD-MN2BD102J J AA 1 kohm,1/8W
R722VRD-MN2BD103J J AA 10 kohm,1/8W
PRICE
RANK
DESCRIPTIONNO.
PRICE
RANK
R724VRD-ST2CD102JJ AA 1 kohm,1/6W
R725VRD-MN2BD102J J AA 1 kohm,1/8W
R726~729VRD-ST2CD222JJ AA 2.2 kohms,1/6W
R732VRD-ST2CD102JJ AA 1 kohm,1/6W
R733~737VRD-MN2BD102J J AA 1 kohm,1/8W
R742VRD-MN2BD102J J AA 1 kohm,1/8W
R743VRD-MN2BD330J J AA 33 ohms,1/8W
R744VRD-MN2BD102J J AA 1 kohm,1/8W
R745VRD-MN2BD104J J AA 100 kohm,1/8W
R748~751VRD-MN2BD103J J AA 10 kohm,1/8W
R753VRD-MN2BD103J J AA 10 kohm,1/8W
R755VRD-ST-2CD472J J AA 4.7 kohm,1/6W
R756,757VRD-MN2BD683J J AA 68 kohms,1/8W
R758,759VRD-MN2BD103J J AA 10 kohm,1/8W
R760,761VRD-MN2BD102J J AA 1 kohm,1/8W
R762,763VRD-MN2BD473J J AA 47 kohms,1/8W
R766~768VRD-MN2BD103J J AA 10 kohm,1/8W
R769VRD-ST2CD103JJ AA 10 kohm,1/6W
R770VRD-MN2BD473J J AA 47 kohms,1/8W
R771VRD-MN2BD104J J AA 100 kohm,1/8W
R772VRD-MN2BD472J J AA 4.7 kohms,1/8W
R773VRD-ST2CD101JJ AA 100 ohm,1/6W
R775~777VRD-MN2BD103J J AA 10 kohm,1/8W
R778VRD-MN2BD102J J AA 1 kohm,1/8W
R779VRD-RT2HD3R3J J AA 3.3 ohms,1/2W
R792VRD-ST-2CD102J J AA 1 kohm,1/6W
R905VRD-ST2CD121JJ AA 120 ohms,1/6W
R906,907VRD-ST2CD102JJ AA 1 kohm,1/6W
R908VRD-ST2CD121JJ AA 120 ohms,1/6W
R909VRD-ST2CD563JJ AA 56 kohms,1/6W
R910,911VRD-RT2HD271J J AA 270 ohms,1/2W
R912,913VRD-ST2EE4R7J J AA 4.7 ohms,1/4W
R914VRD-ST2CD223JJ AA 22 kohms,1/6W
R915VRD-ST2EE821JJ AA 820 ohms,1/4W
R916,917VRD-ST2EE331JJ AA 330 ohms,1/4W
R922VRD-ST2CD223JJ AA 22 kohms,1/6W
R923VRD-ST2CD330JJ AA 33 ohms,1/6W
R924VRD-RT2HD3R3J J AA 3.3 ohms,1/2W
R925VRD-ST2CD223JJ AA 22 kohms,1/6W
R926VRD-ST2CD103JJ AA 10 kohm,1/6W
R927VRD-ST2CD222JJ AA 2.2 kohms,1/6W
R928VRD-ST2CD123JJ AA 12 kohms,1/6W
R929,930VRD-ST2CD221JJ AA 220 ohms,1/6W
R935VRD-RT2HD3R3J J AA 3.3 ohms,1/2W
RD01VRD-ST2CD681JJ AA 680 ohms,1/6W
RD02VRD-MN2BD821J J AA 820 ohms,1/8W
RD03VRD-MN2BD102J J AA 1 kohm,1/8W
RD04VRD-ST2CD152JJ AA 1.5 kohms,1/6W
RD05VRD-ST2CD222JJ AA 2.2 kohms,1/6W
RD06VRD-ST2CD272JJ AA 2.7 kohms,1/6W
RD07VRD-MN2BD392J J AA 3.9 kohms,1/8W
RD08VRD-ST2CD563JJ AA 56 kohms,1/6W
RD09VRD-MN2BD104J J AA 100 kohm,1/8W
RD10VRD-MN2BD821J J AA 820 ohms,1/8W
RD11VRD-ST-2CD102J J AA 1 kohm,1/8W
RD12VRD-MN2BD152J J AA 1.5 kohms,1/8W
RD13VRD-MN2BD681J J AA 680 ohms,1/8W
RD14VRD-ST2CD821JJ AA 820 ohms,1/6W
RD15VRD-MN2BD102J J AA 1 kohm,1/8W
RD16VRD-MN2BD152J J AA 1.5 kohms,1/8W
RD17VRD-MN2BD222J J AA 2.2 kohms,1/8W
RD18VRD-ST2CD272JJ AA 2.7 kohms,1/6W
RD19VRD-MN2BD392J J AA 3.9 kohms,1/8W
RD20VRD-MN2BD562J J AA 5.6 kohms,1/8W
RD21VRD-MN2BD103J J AA 10 kohm,1/8W
RD22VRD-MN2BD153J J AA 15 kohms,1/8W
RD23VRD-MN2BD333J J AA 33 kohms,1/8W
RD24VRD-ST2CD104JJ AA 100 kohm,1/6W
RD25VRD-MN2BD681J J AA 680 ohms,1/8W
RD26VRD-MN2BD682J J AA 6.8 kohms,1/8W
DESCRIPTION
OTHER CIRCUITRY PARTS
BI601/CNS601 QCNWN1540AWZZ J AF Connector Ass’y,5/5Pin
BI702/CNS702 QCNWN1541AWZZ J AH Connector Ass’y,10/10Pin
CNP1QCNCM704GAWZZ J AC Plug,7Pin
CNP2QCNCM704HAFZZ J AC Plug,8Pin
CNP392LCONE6P53253 J AC Plug,6Pin
CNP3A92LCONE6P53254 J AC Plug,6Pin
CNP4QCNCM705FAFZZ J AB Plug,6Pin
CNP1192LCONE5P53254 J AB Plug,5Pin
CNP1292LCONEAP53254 J AD Plug,10Pin
– 3 –
CD-BA120/125
NO.PARTS CODE
CNP101QCNCM705AFZZJPlug,3Pin
CNP102QCNCM707GAFZZ JPlug,7Pin
CNP30192LCONE3P5268 J AC Plug,3Pin
CNP701QCNCWZX18AWZZ J AD Plug,18Pin
CNP801QCNCM049BAWZZ J AC Plug,2Pin
CNP901QCNCM035FAWZZ J AC Plug,6Pin
CNS1A/BQCNWN1537AWZZ J AG Connector Ass’y,7/7Pin
CNS2A/BQCNWN1538AWZZ J AG Connector Ass’y,8/8Pin
CNS3A/BQCNWN1539AWZZ J AE Connector Ass’y,6/6Pin
CNS701QCNCWZY18AWZZ J AD Plug,18Pin
CNS703QCNCWZY13AWZZ J AC Plug,13Pin
! F90192LFUSET302DJ AD Fuse,3A/250V
! F90292LFUSET162DJFuse,1.6A/250V
FFC13QCNWN1544AWZZ J AE Flat Cable,13Pin
FFC18QCNWN1613AWZZ J AF Flat Cable,18Pin
FL701VVKSVA9MS13-1 J AZ FL Display
FW901QCNWN1612AWZZ J AD Connector Ass’y,5Pin
JK901QJAKM0010AWZZ J AF Jack,Headphones
LG901QLUGP0001AWZZ J AC Lug
LUG1QLUGP0002AWZZ J AB Lug
M192LMTR2790CASY J BB Motor with Chassis [Spindle]
M292LMTR1854BASY J AP Motor with Gear [Sled]
M392LTWMEN7E6YJMotor with Worm Pulley
RX701VHLN63H380A-1J AK Remote Sensor,N63H380A
SO801QSOCA0209AWZZ J AH Socket,AC Input
SO901QTANA0416AWZZ J AE Terminal,Speaker
SW4QSW-F9001AW01 J AD Switch,Leaf Type [Pickup In]
SW70192LSWICHT1663T J AC Switch,Key Type [POWER]
SW70292LSWICHT1663T J AC Switch,Key Type [CLOCK]
SW70392LSWICHT1663T J AC Switch,Key Type
SW70992LSWICHT1663T J AC Switch,Key Type [DISC SKIP]
SW71092LSWICHT1663T J AC Switch,Key Type
SW71192LSWICHT1663T J AC Switch,Key Type
SW71292LSWICHT1663T J AC Switch,Key Type [Volume Up]
SW71392LSWICHT1663T J AC Switch,Key Type [Volume Down]
SW71492LSWICHT1663T J AC Switch,Key Type [CD]
SW71592LSWICHT1663T J AC Switch,Key Type [Tape]
SW71692LSWICHT1663T J AC Switch,Key Type
SW71792LSWICHT1663T J AC Switch,Key Type [Memory/Set]
SW71892LSWICHT1663T J AC Switch,Key Type [Rewind]
SW71992LSWICHT1663T J AC Switch,Key Type [Fast Forward]
SW72092LSWICHT1663T J AC Switch,Key Type [Play/Repeat]
SW72192LSWICHT1663T J AC Switch,Key Type [Stop]
SW72392LSWICHT1663T J AC Switch,Key Type [REC/PAUSE]
SW72492LSWICHT1663T J AC Switch,Key Type
SW72592LSWICHT1663T J AC Switch,Key Type [Tuner/Band]
PRICE
RANK
DESCRIPTION
[T/T Up/Down Loading]
[TIMER/SLEEP]
[OPEN/CLOSE]
[X-BASS/DEMO]
[Tuning/Time Down]
[TUNING/TIME UP]
CD MECHANISM PARTS
301NGERH0011AWZZ J AC Gear,Middle
302NGERH0012AWZZ J AC Gear,Drive
303MLEVP0080AWZZ J AC Rail,Guide
304NSFTM0020AWFW J AD Shaft,Guide
30592LM-CUSN1524A J AC Cushion
! 30692LHPC1LXASYJ BD Pickup Unit Ass’y
306- 1 ————–– Pickup Unit
306- 2NGERR0043AFZZ J AC Gear,Rack
306- 3MSPRC0961AFZZ J AA Spring,Rack
701XBSSD26P06000J AA Screw,ø2.6×6mm
702XHBSD20P05000 J AA Screw,ø2×5mm
703XBBSD20P03000J AA Screw,ø2×3mm
704LX-WZ1070AFZZJ A A Washer,ø1.5 ×ø3.8×0.25mm
M192LMTR2790CASY J BB Motor with Chassis [Spindle]
M292LMTR1854BASY J AP Motor with Gear [Sled]
SW4QSW-F9001AW01 J AD Switch,Leaf Type [Pickup In]
204- 2GCOVA1254AWSA J AE Cover,CD Tray Panel,Left
204- 3GCOVA1255AWSA J AE Cover,CD Tray Panel,Right
205GCAB-1184AWSA J AP Top Cabinet
206GITAR0548AWSA J AH Rear Panel [120 for U.S.A.]
206GITAR0565AWSA JRear Panel [120 for Canada]
206GITAR0566AWSA JRear Panel
206GITAR0568AWSA JRear Panel [125 for Canada]
206GITAR0569AWSA JRear Panel [125 for Central
206GITAR0573AWSA JRear Panel [125 for U.S.A.]
208LANGK0110AWFW1 J AD Support,Cassette Lock,Tape 1
209LANGK0111AWFW1 J AD Support,Cassette Lock,Tape 2
213LCHSM0098AWFW J AQ Main Chassis
214LHLDZ1087AWSA1 J AC Holder,FL Display
219MLOKC0003AWZZ J AD Lock Lever,Cassette,Tape 1
220MLOKC0004AWZZ J AD Lock Lever,Cassette,Tape 2
221MSPRD0109AWFJ J AB Spring,Cassette Lock,Tape 1
222MSPRD0110AWFJ J AB Spring,Cassette Lock,Tape 2
22492LPT0331105J AM Table Loading
225PCUSG0022AWZZ J AB Cushion,Leg
226PRDAR0004BGFW JHeat Sink,Main
230QCNWN1615AWZZ J AC Lug Wire
! 231QFSHD0001AWZZ J AB Holder,Fuse
23292LBE241414J AD Belt
23492LEVA0330702JVelvet Carpet,Chassis
23592LMAG0104302JMagnet
23692LMT0304302JPlate,Metal
23792LNBAND1318A J AA Nylon Band,80mm
23892LNM0305401JVelvet Carpet
23992LPT0303002J AB Roller
24092LPT0304303J AB Lever,Stop
24192LPT0304304JStopper
24292LPT0304305J AE Lever,Lock
24392LPT0304306JStabilizer
24492LPT0304307J AC Support,Cam
24592LPT0304308JLock Gear Pin
24692LPT0304309JCap,Pulley Stopper
24792LPT0305413JCam Gear Lower
24892LPT0309506J AD Gear,Turntable Drive
24992LPT0309507J AD Gear,Open/Close Drive
25092LPT0309508J AD Gear,Planet
25192LPT0309509J AD Gear,Drive
25292LPT0309510J AE Gear,Pulley
25392LPT0309511J AD Gear,Middle
25492LPT0311101J AB Lever,Clamp
25592LPT0311102J AC Lever,Disc
25692LPT0312005JGear,Cam
PRICE
RANK
DESCRIPTIONPARTS CODE
(Not Replacement Item)
(Not Replacement Item)
(Not Replacement Item)
[120 for Central America/
Mexico]
America/Mexico]
– 4 –
CD-BA120/125
PARTS CODENO.PARTS CODE
25792LPT0320201J AE Support,Stabilizer
25892LPT0330301J AU Chassis,Loading
25992LPT0330803J AK CD,Chassis
26092LPT0331003J AT Chassis,Slide
26292LSP0304303JSpring,Stopper
26392LSP0304305J AB Spring,Lock
26492LSP0304306JSpring,Lock Gear
268KMECB0011AWZZ J BH Tape Mechanism Ass’y
270LHLDZ1230AWZZ J AC Holder,LED
271PRDAR0005BGFW JHeat Sink,Sub
604XEBSF30P12000J AA Screw,ø3×12mm
605XESSD30P10000J AA Screw,ø3×10mm
606XHBSD26P04000 J AA Screw,ø2.6×4mm
610XJBSF30P10000J AA Screw,ø3×10mm
611XJBSD30P08000J AA Screw,ø3×8mm
612LX-HZ0009AWFD J AC Screw,Special
613LX-HZ0082AFZZJ AA Screw,ø4×8mm
614LX-JZ0010AFFDJ AA Screw,Special
616LX-BZ2222AXZZJScrew,Special
617LX-JZ0004AWFDJ AA Screw,ø3×12mm
61892LSC0308MBZIJ AB Screw,ø3× 8mm
61992LSC0308RBZIJScrew,ø3×8mm
620XEBSD26P08000J AA Screw,ø2.6×8mm
PRICE
RANK
DESCRIPTIONNO.
PACKING PARTS
SPAKA0242AWZZ JPacking Add.,Left/Right
SPAKC0917AWZZ JPacking Case [120 for Canada]
SPAKC0918AWZZ JPacking Case
SPAKC0968AWZZ JPacking Case
SPAKC0969AWZZ JPacking Case [125 for Canada]
SPAKP0013AWZZ1 J AC Polyethylene Bag,Unit
SPAKZ0573AWZZ JSheet,CD Tray
92LBAG1460C1J AB Polyethylene Bag,Accessories
[120 for Central America/
Mexico]
[125 for Central America/
Mexico]
ACCESSORIES
QACCD0020AWZZ J AN AC Power Supply Cord
QACCD0025AWZZ J AN AC Power Supply Cord
QANTL0007AWZZ J AK AM/FM Loop Antenna
TINSZ0533AWZZJ AB Quick Guide
TINSZ0534AWZZJOperation Manual
TINSZ0538AWZZJQuick Guide
TLABR1090AWZZ J AB Label,Bar Code [120]
TLABR1130AWZZ JLabel,Bar Code [125]
TLABZ0711AWZZ JLabel,Feature,Tape 1 [120]
TLABZ0712AWZZ JLabel,Feature,Tape 2
TLABZ0718AWZZ JLabel,Feature,Tape 1 [125]
RRMCG0229AWSA J AR Remote Control
JBattery Lid,Remote Control
[Except for Canada]
[For Canada]
[120 for U.S.A.]
[125 for U.S.A.]
[120 for Canada]
[125 for Canada]
[120 for Central America
Mexico]
[120 for U.S.A. Only]
[125 for Central America/
Mexico]
[125 for U.S.A. Only]
PRICE
RANK
PWB-D ————–– Tape Mechanism
PWB-E92LPC99C017JCD Loading Motor (PWB Only)
DESCRIPTION
OTHER SERVICE PART
UDSKA0004AFZZ J AZ CD Pickup Lens Cleaner
CP-BA120/125
SPEAKER BOX PARTS
90192LJ1911BJ AU Net Frame Ass’y
90292L9553CJ AW Speaker Box Ass’y
90392LJ9797CJ AE Port Cushion
90492LP5880JLabel,Specifications [CP-BA125]
90492LP5879J AC Label,Specifications [CP-BA120]
90592LF1377AJ AC Screw,
90692LD4680CJSpeaker Cord
90792LJ1912BJ AX Duct Panel
SP1,2VSP0010PBY38A J AU Speaker
SPEAKER PACKING PARTS
92LN1885BJPacking Add.,Speaker,Bottom
92LN1885TJPacking Add.,Speaker,Top
92LV4974AJ AC Polyethylene Bag,Speaker
GBOXS0042AWM1
SPEAKER BOX PARTS REAR SPEAKER
(CD-BA125 Only)
90192LSRCNF006RS JNet Frame Ass’y
90292LSRCBC010RS JBottom Cabinet
90392LSRCSC004RS J AK Speaker Cord
90492LSRCSW005RS J AB Screw,ø3×12mm
90592LSRCPL016RS JLabel,Parts Code
No part of this publication may be reproduced,
stored in a retrieval system, or transmitted in
any from or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without
prior written permission of the publisher.
SHARP CORPORATION
Communication Systems Group
Quality & Reliability Control Center
Higashihiroshima, Hiroshima 739-0192, Japan
Printed in Japan
A0002-2627NS•HA•I
SC • SL • LAG
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.