Sharp AR-3500, AR-M350, AR-M450, AR-P350, AR-P450 User Manual

...
Warranty
While every effort has been made to make this document as accurate and helpful as possible, SHARP Corporation makes no warranty of any kind with regard to its content. All information included herein is subject to change without notice. SHARP is not responsible for any loss or damages, direct or indirect, arising from or related to the use of this operation manual.
© Copyright SHARP Corporation 2001. All rights reserved. Reproduction, adaptation or translation without prior written permission is prohibited, except as allowed under copyright laws.
Trademark Acknowledgments
Macintosh, Power Macintosh, Mac OS, LaserWriter, and AppleTalk are registered trademarks of Apple Computer, Inc.
IBM, PC/AT, and PowerPC are trademarks of International Business Machines Corporation.
Pentium is a registered trademark of Intel Corporation.
PCL is a trademark of the Hewlett-Packard Company.
PostScript® is a registered trademark of Adobe Systems Incorporated.
NetWare is a registered trademark of Novell, Inc.
All other trademarks and copyrights are the property of their respective owners.
INSTALLATION REQUIREMENTS
31-1/2" (80cm)
23-5/8" (60cm)
23-5/8" (60cm)
11-13/16" (30cm)
Improper installation may damage this product. Please note the following during initial installation and whenever the machine is moved.
1. The machine should be installed near an accessible power outlet for easy connection.
2. Be sure to connect the power cord only to a power outlet that meets the specified voltage and current requirements. Also make certain the outlet is properly grounded.
For the power supply requirements, see the name plate of the main unit.
3. Do not install your machine in areas that are:
damp, humid, or very dusty
exposed to direct sunlight
poorly ventilated
subject to extreme temperature or humidity changes, e.g., near an air conditioner or heater.
4. Be sure to allow the required space around the machine for servicing and proper ventilation.
A small amount of ozone is produced within the printer during operation. The emission level is insufficient to cause any health hazard.
NOTE:
The present recommended long term exposure limit for ozone is 0.1 ppm (0.2 mg/m calculated as an 8 hr. time-weighted average concentration. However, since the small amount that is emitted may have an objectionable odor, it is advisable to place the copier in a ventilated area.
3
)
0-1
INSTALLATION REQUIREMENTS
Moving this machine
Lift this machine at the positions shown in the illustration below and carry it horizontally.
CAUTION
Two people are required to lift and carry this machine. The center of gravity of the machine is slightly to the left of the center of the machine when viewed from the front. If a duplex module is installed the center of gravity will be even further shifted to the left. When lifting the machine be careful to steady it to prevent it from toppling. Also be sure that all covers and the duplex module are securely closed and latched before lifting. If a duplex module is installed, do not lift the machine by the module as it may come off causing it and the machine to drop.
Remove the multi purpose drawer and lift at the positions shown in the illustration. For removal and installation of the multi purpose drawer, see page 4-4. To avoid injury be sure to completely remove the multi purpose drawer.
Front side Rear side
Remove the multi purpose drawer in advance.
If the machine has been placed on a stand/paper drawer: The stand/paper drawer is equipped with casters for moving. Unlock the adjusters of the stand/paper drawer and gently move the machine taking care to steady it to prevent it from toppling. For locking and unlocking the adjusters, see page 0-3.
CAUTIONS
The center of gravity of this machine is a little deviated to the left from the center. If the machine is not equipped with a multi purpose drawer or a stand/paper drawer, take care in opening the left side cover (or the duplex module) not to cause toppling of the machine.
Do not cover the ventilating holes of this machine. Do not install this machine in a location where these holes are covered. If these holes are covered, heat will not be dissipated and a fire may be caused.
Ventilating holes
0-2
CAUTIONS
1. Do not touch the photoconductive drum. Scratches or smudges on the drum will cause dirty prints.
2. The fusing unit is extremely hot. Exercise care in this area.
3. Do not look directly at the light source of the scanner module. Doing so may damage your eyes.
4. Five adjusters are provided on all optional stand/ paper drawer units. These adjusters should be lowered until they contact the floor.
5. Do not make any modifications to this machine. Doing so may result in personal injury or damage to the machine.
6. Since this machine is heavy, it is recommended that it be moved by more than one person to prevent injury.
7. When connecting this machine to a computer, be sure to first turn both the computer and the machine off.
8. Do not print anything which is prohibited from printing by law. The following items are normally prohibited from printing by national law. Other items may be prohibited by local law.
Money ● Stamps
Bank drafts ● Checks ● Passports
Driver's licenses
Bonds
Stocks
Fusing unit
Adjuster
Lock Release
9. Do not throw toner or a toner cartridge into fire. Toner may be spattered, causing a burn.
0-3
CAUTIONS
Cautions on laser
Wave length
Pulse times North America: 35 cpm model: (4.1 µs ± 4.1 ns)/7 mm
Output power 0.2 mW - 0.4 mW
At the production line, the output power of the scanner unit is adjusted to 0.4 MILLIWATT PLUS 8 % and is maintained constant by the operation of the Automatic Power Control (APC).
Caution
This product contains a low power laser device. To ensure safety do not remove any cover or attempt to gain access to the inside of the product. Refer all servicing to qualified personnel.
785 nm
Europe: 31 cpm model: (3.8 µs ± 3.8 ns)/7 mm
+10 nm
15 nm
45 cpm model: (5.7 µs ± 5.7 ns)/7 mm
35 cpm model: (3.8 µs ± 3.8 ns)/7 mm 45 cpm model: (4.4 µs ± 4.4 ns)/7 mm
For North America:
SAFETY PRECAUTIONS
This Digital Equipment is rated Class 1 and complies with 21 CFR 1040.10 and 1040.11 of the CDRH standards. This means that the equipment does not produce hazardous laser radiation. For your safety, observe the precautions below.
Do not remove the cabinet, operation panel or any other covers.
The equipment's exterior covers contain several safety interlock switches. Do not bypass any safety interlock by inserting wedges or other items into switch slots.
Caution
Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
0-4
For Europe:
CAUTION
INVISIBLE LASER RADIATION WHEN OPEN INTERLOCKS DEFEATED. AVOID EXPOSURE TO BEAM.
VORSICHT
UNSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GEÖFFNET UND SICHERHEITSVERRIEGELUNG ÜBERBRÜCKT. NICHT DEM STRAHL AUSSETZEN.
ADVARSEL
USYNLIG LASERSTRÅLNING VED ÅBNING, NÅR SIKKERHEDSBRYDERE ER UDE AF FUNKTION. UNDGÅ UDSAETTELSE FOR STRÅLNING.
VAROITUS!
LAITTEEN KÄYTTÄMINEN MUULLA KUIN TÄSSÄ KÄYTTÖOHJEESSA MAINITULLA TAVALLA SAATTAA ALTISTAA KÄYTTÄJÄN TURVALLISUUSLUOKAN 1 YLITTÄVÄLLE NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE.
VARNING
OM APPARATEN ANVÄNDS PÅ ANNAT SÄTT ÄN I DENNA BRUKSANVISNING SPECIFICERATS, KAN ANVÄNDAREN UTSÄTTAS FÖR OSYNLIG LASERSTRÅLNING, SOM ÖVERSKRIDER GRÄNSEN FÖR LASERKLASS 1.
CLASS 1 LASER PRODUCT
LASER KLASSE 1
LUOKAN 1 LASERLAITE
KLASS 1 LASERAPPARAT
CAUTIONS
INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS DEFEATED. AVOID EXPOSURE TO BEAM.
Laserstrahl
CAUTION VORSICHT ADVARSEL ADVERSEL VARNING VARO !
UNSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GEÖFFNET UND SICHERHEITSVERRIEGELUNG ÜBERERÜCKT. NICHT DEM STRAHL AUSSETZEN.
USYNLIG LASERSTRÅLING VED ÅBNING, NÅR SIKKERHEDSAFBRYDERE ER UDE AF FUNKTION. UNDGÅ UDSAETTELSE FOR STRÅLNING.
USYNLIG LASERSTRÅLING NÅR DEKSEL ÅPNES OG SIKKERHEDSLÅS BRYTES. UNNGÅ EKSPONERING FOR STRÅLEN.
OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD OCH SPÄRRAR ÄR URKOPPLADE. STRÅLEN ÄR FARLIG. BETRAKTA EJ STRÅLEN.
AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALTTIINA NÄKYMÄTÖNTÄ LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.
CLASS 1
LASER PRODUCT
LASER KLASSE 1
0-5
FACSIMILE FEATURE
TEL
LINE
TEL
LINE
Line connector
Line connection
Use the telephone cable supplied with the facsimile expansion kit to connect the machine to a telephone line. Connect the cable so that the connector nearest to the noise suppression core is inserted into the socket located of the expansion kit box. Insert the other end into the telephone line socket.
Core
Fax power switch
For the facsimile features to function, the power switch located on the expansion kit box must be turned on.
Fax power switch
ON
OFF
0-6
CONTENTS
Page
INSTALLATION REQUIREMENTS . . . . . . . . . . . . 0-1
Carrying this machine . . . . . . . . . . . . . . . . . . . . 0-2
CAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-3
FACSIMILE FEATURE . . . . . . . . . . . . . . . . . . . . . 0-6
CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-7
CHAPTER 1 BEFORE USING THE PRODUCT
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
MAIN FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
PART NAMES AND FUNCTIONS . . . . . . . . . . . . 1-4
Exterior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Interior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
Part names and functions of
peripheral devices . . . . . . . . . . . . . . . . . . . . . . . 1-6
Operation panel of the main unit . . . . . . . . . . . . 1-9
Operation panel of the scanner module . . . . . 1-12
Touch panel (on the scanner module) . . . . . . 1-13
LOADING PAPER . . . . . . . . . . . . . . . . . . . . . . . . 1-16
Loading paper in paper tray 1 . . . . . . . . . . . . . 1-16
Changing the paper size in paper tray 1 . . . . . 1-16
Specifications of paper trays . . . . . . . . . . . . . . 1-17
Setting the paper size and type . . . . . . . . . . . 1-19
Loading paper in the multi purpose drawer . . . 1-21
Specifications (multi purpose drawer) . . . . . . . 1-23
Loading paper in the stand/
3 x 500 sheet paper drawer . . . . . . . . . . . . . . 1-23
Specifications
(stand/3 x 500 sheet paper drawer) . . . . . . . . 1-23
Loading paper in the stand/
MPD & 2000 sheet paper drawer . . . . . . . . . . 1-24
Specifications
(stand/MPD & 2000 sheet paper drawer) . . . . 1-24
ADDING TONER. . . . . . . . . . . . . . . . . . . . . . . . . 1-25
STORAGE OF SUPPLIES . . . . . . . . . . . . . . . . . 1-25
CHAPTER 2
PRINTING FROM A COMPUTER
CONNECTING TO A COMPUTER . . . . . . . . . . . . 2-2
SOFTWARE FOR WINDOWS . . . . . . . . . . . . . . . 2-2
INSTALLING PRINTER DRIVERS AND
PRINTER UTILITIES . . . . . . . . . . . . . . . . . . . . . . 2-3
UNINSTALLING PRINTER DRIVERS AND
PRINTER UTILITIES . . . . . . . . . . . . . . . . . . . . . . 2-3
INSTALLING PRINTER DRIVERS USING PLUG &
PLAY OR THE “ADD PRINTER WIZARD” . . . . . . 2-4
Before installation . . . . . . . . . . . . . . . . . . . . . . . 2-4
SETTING THE PRINTER DRIVER . . . . . . . . . . . . 2-5
Printer driver settings under Windows
(selecting and setting print conditions) . . . . . . . 2-5
PRINTER CONFIGURATION THROUGH
THE NETWORK . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
Environment required for accessing
Web pages . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
Accessing Web pages and displaying help . . . . 2-6
Items and outline of menu frame of
Web pages . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
JOB CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9
“JOB CONTROL” operation. . . . . . . . . . . . . . . . 2-9
Hold job list . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
Printer account control . . . . . . . . . . . . . . . . . . 2-12
USING THE MACHINE AS A POSTSCRIPT
PRINTER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13
Using the printer in the Windows
environment . . . . . . . . . . . . . . . . . . . . . . . . . 2-13
Using the printer in the Macintosh
environment . . . . . . . . . . . . . . . . . . . . . . . . . 2-15
CHAPTER 3
PRINTER BASIC SETTINGS
MAKING CONFIGURATION SETTING . . . . . . . . 3-2
Operation procedure common to all printer configuration settings (items that can be set
from the operation panel) . . . . . . . . . . . . . . . . . 3-2
Default settings . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
PCL settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
PostScript settings . . . . . . . . . . . . . . . . . . . . . . 3-5
CUSTOM SETTINGS . . . . . . . . . . . . . . . . . . . . . . 3-6
Operation procedure common to all custom settings (items that can be set from the
operation panel) . . . . . . . . . . . . . . . . . . . . . . . . 3-6
Setting items . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8
0-7
CONTENTS
CHAPTER 4
TROUBLESHOOTING AND MAINTENANCE
MISFEED REMOVAL . . . . . . . . . . . . . . . . . . . . . . 4-2
General misfeed removal procedure . . . . . . . . . 4-2
Misfeed removal guidance . . . . . . . . . . . . . . . . 4-3
Misfeed in the paper feed area . . . . . . . . . . . . . 4-4
Misfeed in the transport area, fusing area,
and exit area . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Misfeed in the duplex module . . . . . . . . . . . . . . 4-7
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . 4-8
USER MAINTENANCE . . . . . . . . . . . . . . . . . . . . 4-11
Cleaning the scanner module . . . . . . . . . . . . . 4-11
CHAPTER 5
PERIPHERAL DEVICES
DUPLEX MODULE . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Part names . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
Loading paper in the bypass tray . . . . . . . . . . . 5-3
Setting the printer driver for duplex module,
bypass tray and exit tray . . . . . . . . . . . . . . . . . . 5-4
Copying in the duplex mode . . . . . . . . . . . . . . . 5-4
Troubleshooting (concerning the duplex module)5-5
MAIL-BIN STACKER . . . . . . . . . . . . . . . . . . . . . . . 5-6
Part names . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
Specifying mail bins to receive printed output. . 5-7
Setting in the printer driver . . . . . . . . . . . . . . . . 5-7
Misfeed in the mail-bin stacker . . . . . . . . . . . . . 5-8
FINISHER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9
Part names . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9
Finisher functions . . . . . . . . . . . . . . . . . . . . . . 5-10
Using the finisher functions . . . . . . . . . . . . . . . 5-11
Staple cartridge replacement . . . . . . . . . . . . . 5-12
Misfeed in the finisher . . . . . . . . . . . . . . . . . . . 5-14
Troubleshooting finisher problems . . . . . . . . . 5-15
Stapling position quick reference guide for
duplex output . . . . . . . . . . . . . . . . . . . . . . . . . 5-16
SADDLE STITCH FINISHER . . . . . . . . . . . . . . . 5-17
Part names . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-17
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . 5-17
Saddle stitch finisher functions . . . . . . . . . . . . 5-18
Using the saddle stitch finisher . . . . . . . . . . . . 5-20
Staple cartridge replacement and
staple jam removal . . . . . . . . . . . . . . . . . . . . . 5-21
Misfeed in the saddle stitch finisher . . . . . . . . 5-24
Troubleshooting
(concerning the saddle stitch finisher) . . . . . . 5-26
Stapling position quick reference guide for
duplex output . . . . . . . . . . . . . . . . . . . . . . . . . 5-27
Relation between print image and
saddle stitch . . . . . . . . . . . . . . . . . . . . . . . . . . 5-28
CHAPTER 6
KEY OPERATOR PROGRAMS
KEY OPERATOR PROGRAMS . . . . . . . . . . . . . . 6-2
Key operator program list . . . . . . . . . . . . . . . . . 6-2
Using the key operator programs . . . . . . . . . . . 6-3
Description of setting programs . . . . . . . . . . . . 6-7
CHAPTER 7
APPENDIX
PRINTER SPECIFICATIONS . . . . . . . . . . . . . . . . 7-2
List of principal printer driver functions . . . . . . . 7-3
LIST OF COMBINATION OF
PERIPHERAL DEVICES . . . . . . . . . . . . . . . . . . . 7-4
NOTICE PAGE PRINTING . . . . . . . . . . . . . . . . . . 7-5
PRINT AREA . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-6
INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-7
KEY OPERATOR CODE NUMBER . . . . . . . . . . 7-11
0-8
CHAPTER 1
BEFORE USING THE PRODUCT
This chapter describes basic information that should be read before using
this product.
Page
INTRODUCTION ...................................................................................... 1-2
MAIN FEATURES .................................................................................... 1-3
PART NAMES AND FUNCTIONS ........................................................... 1-4
Exterior ............................................................................................... 1-4
Interior ................................................................................................ 1-5
Part names and functions of peripheral devices ............................... 1-6
Operation panel of the main unit ....................................................... 1-9
Operation panel of the scanner module ............................................ 1-12
Touch panel (on the scanner module) .............................................. 1-13
LOADING PAPER .................................................................................... 1-16
Loading paper in paper tray 1 ........................................................... 1-16
Changing the paper size in paper tray 1 ........................................... 1-16
Specifications of paper trays ............................................................. 1-17
Setting the paper size and type ......................................................... 1-19
Loading paper in the multi purpose drawer ...................................... 1-21
Specifications (multi purpose drawer) ............................................... 1-23
Loading paper in the stand/3 x 500 sheet paper drawer .................. 1-23
Specifications (stand/3 x 500 sheet paper drawer) .......................... 1-23
Loading paper in the stand/MPD & 2000 sheet paper drawer ......... 1-24
Specifications (stand/MPD & 2000 sheet paper drawer) .................. 1-24
ADDING TONER ...................................................................................... 1-25
STORAGE OF SUPPLIES ....................................................................... 1-25
1-1
INTRODUCTION
To gain the maximum benefits in using this product, it is recommended that the user read this manual to become familiar with all the features and functions of the basic product and the precautionary information contained in the manual.
NOTE
In this manual, American spellings are used.
This product is a high speed laser printer that can be extended to become multifunctional through the installation of optional peripheral devices. The product can be extended to include copier, network scanning, facsimile or network printing capabilities. This manual describes the basic use of the product as a printer and does not contain use information for any of the optional peripheral devices. Separate operation manuals are included with each of the optional peripheral devices. Refer to these manuals for their operation.
Original and paper sizes
This machine allows use of standard sizes in both the inch and AB systems. The standard sizes available in this machine are shown below.
Sizes in the inch system Sizes in the AB system
When the machine is being When the machine is being operated from the operation operated from the touch panel on panel on the main unit: a scanner module:
LEDGER 11 x 17 A3
LEGAL 8-1/2 x 14 B4
FOOLSCAP 8-1/2 x 13 A4
LETTER 8-1/2 x 11 B5
EXECUTIVE 7-1/4 x 10-1/2 A5
INVOICE 5-1/2 x 8-1/2
In this manual, the indications for the scanner module touch panel as shown in the table above are used.
The meaning of “R” in original and paper size indications
Some original and paper sizes can be placed in either the portrait or landscape orientations. To differentiate between landscape and portrait, the landscape orientation size indication will contain an “R”. These are indicated as 8-1/2 x 11R, 5-1/2 x 8-1/2R, A4R, B5R, etc. Sizes that can be placed only in the landscape orientation (11 x 17, 8-1/2 x 14, 8-1/2 x 13, A3, B4) do not contain the “R” in their size indication.
Size indication with “R” Size indication without “R”
Landscape orientation Portrait orientation
1-2
MAIN FEATURES
Laser printer able to accept a range of peripherals allowing it to be configured to specific needs
This product is a laser printer that can be used as a local printer which can be configured by the addition of peripheral devices to extend its capabilities to include copier, network printer, network scanner or facsimile features.
A range of optional units to enhance productivity
Optional additions such as duplex units for producing two-sided output, additional paper feed units to increase the variety of available paper sizes and paper capacity, paper output units to sort and otherwise organize the output and a scanner module for automatically scanning documents.
600 dpi high resolution printing
High-definition and high quality printing with 600 dpi resolution can be performed. Also high image quality equivalent to 1200 dpi can be output by using a smoothing function.
High speed monochrome printing
Depending upon the model chosen, high speed printing at 35 letter (A4) size pages/minute or 45 letter (A4) size pages/minute is available.
PostScript compatible
Installation of a PS3 expansion kit gives PostScript compatibility (PostScript level 3).
1
Energy saving features
This product has the following two power reducing modes that conform to the Energy Star guidelines which help to conserve natural resources and reduce environmental pollution.
Preheat mode
The preheat mode is the first level of power reduction. The power is reduced to the fuser unit a preset time after the machine has completed a job and no further machine operations have been made. The machine can recover to the ready condition within a short period of time. The preset time to enter the mode can be set by a key operator program.
Auto power shut-off mode
The auto power shut-off mode is the second level of power reduction. In this mode power is shut off to the fusing unit and the touch panel. In this state more energy is saved than in the preheat mode but the time to recover to the ready condition will be longer. The preset time to enter this mode can be set by a key operator program.
When this product is used as a printer, and either of the above modes is active, the mode will be deactivated automatically by an incoming job and the machine will automatically warm up and start to print when it has reached the ready temperature. When this product is configured for multi-function operation, and either of the above modes is active, the mode will be deactivated as above by either an incoming print job or received facsimile data. Either mode will also be deactivated by any key operation on the operation panel or by the action of an original being placed for copying or facsimile transmission.
ENERGY STAR
As an Partner, SHARP has determined that this product meets the
ENERGY STAR
guidelines for energy efficiency.
®
®
1-3
PART NAMES AND FUNCTIONS
Exterior
Bypass tray paper guide
Exit tray*
Duplex module/bypass tray*
Module for two-sided printing
Upper paper output area
Finished sheets are deposited here.
Upper exit tray extension*
Provides support for large size paper.
Operation panel (See page 1-9.)
* , , , , , and are peripheral devices. For description of these devices, see page 1-7. One of devices ,
, and must be installed. If you install or , a power supply unit (page 1-8) must also be installed.
Front cover
Open to add toner .
Main switch
Press to turn power on and off.
Paper tray 1
Stand/3 x 500 sheet paper drawer* (See page 1-23.)
Stand/MPD & 2000 sheet paper drawer* (See page
1-24.)
Multi purpose drawer* (See page 1-21.)
1-4
Interior
PART NAMES AND FUNCTIONS
1
Duplex module side cover
Open when a misfeed has occurred in the duplex module.
Side cover latch
Push up to open the side cover when a misfeed has occurred in the main unit.
Fusing unit
Lift up to open the side cover when a misfeed has occurred in the main unit.
CAUTION
The fusing unit is hot. Take care in removing misfed paper.
Developer cartridge*
This cartridge contains developer and must be removed and replaced by a new cartridge when indicated on the operation panel.
Toner cartridge (drum/toner cartridge)* The toner cartridge must be replaced when indicated
on the operation panel.
Photoconductive drum
Images are formed on the photoconductive drum.
NOTE
Do not touch or damage the photoconductive drum.
Cartridge lock lever
When replacing the drum, toner or developer cartridge, turn down this lever and pull it out.
* For replacement and installation of cartridges, refer to the Operation Manual (Read this document before installing the
product.).
1-5
PART NAMES AND FUNCTIONS
Part names and functions of peripheral devices
1-6
PART NAMES AND FUNCTIONS
B/W scanner module/DSPF (AR-EF1)
The B/W scanner module/DSPF is a monochrome scanner that uses two scanning modes. In one mode, sheet originals are fed and scanned by the action of the moving originals. In this mode either one side of an original can be scanned or both sides of an original can be scanned at the same time. The other mode of scanning uses a moving mirror for scanning originals placed on the glass platen.
Upper exit tray extension (AR-TE4)
Mount this unit to the upper paper exit tray. This extension is needed to support large size paper.
Finisher (AR-FN6)
Output sheets can either be sorted in page order or grouped by page. Sorted sets or groups are offset stacked for easy separation when removed. Sorted sets can be delivered either stapled or unstapled.
Mail-bin stacker (AR-MS1)
This unit is an output sorter that has seven receiving bins. The bin to receive printed output can be selected in the printer driver. Each bin can be assigned to receive printed output by an individual person or by groups of people so that their prints are separated from other users making them easy to retrieve. When this unit is installed, any copies or facsimile prints will be sent to the top tray and not into the mail bins.
Multi purpose drawer (AR-MU1)
Up to 500 sheets of 20 lbs. (80 g/m loaded. Also special papers such as envelopes (standard sizes only) and postcards can be set.
Stand/3 x 500 sheet paper drawer (AR-D14)
This paper feed unit contains an upper multi-purpose drawer (see item which can hold a maximum of 500 sheets of 20 lbs. (80 g/m
Saddle stitch finisher (AR-FN7)
The saddle stitch finisher can automatically place two staples for centerline binding of prints or copies and fold them along the centerline. An optional hole punching unit is available for installation into the finisher.
Duplex module (AR-DU3)
An optional duplex module must be installed for automatic two-sided printing.
Duplex module/bypass tray (AR-DU4)
This module is basically the same as above with the addition of a manual bypass paper feed unit.
Exit tray (AR-TE3)
Mounted to the paper output port of a duplex module.
2
) paper.
) and two lower drawers each of
2
) paper can be
1
Stand/MPD & 2000 sheet paper drawer (AR-D13)
This paper feed unit contains an upper multi-purpose drawer (see item hold a maximum of 2000 sheets of 20 lbs. (80 g/m paper.
Some peripheral devices cannot be installed together while others may require the installation of one or more others to be functional. See page 7-4, “LIST OF COMBINATION OF PERIPHERAL DEVICES.” Peripheral devices are basically optional, but some are provided as standard equipment for some models.
) and a lower drawer which can
2
)
1-7
PART NAMES AND FUNCTIONS
■■
Other optional equipment
■■
Scanner rack (AR-RK1)
This rack is required to support the scanner module above the printer.
Power supply unit (AR-DC1)
Some peripheral devices require the installation of this power supply.
Print server card (AR-NC5J)
A NIC (network interface card) is necessary for connecting the printer to a network.
Multi-function controller board (AR-M11)
This print controller is necessary to provide copier, facsimile and network scanning capabilities.
PS3 expansion kit (AR-PK1)
This kit provides compatibility of PostScript level 3 to the printer.
Hard disk drive (AR-HD3)
Extends the image storing capacity for the printer and copier features. This unit is required for the job retention function (see page 2-9) to operate.
Facsimile expansion kit (AR-FX5)
This kit is required to add facsimile features.
Additional fax memory (8 MB) (AR-MM9)
Network scanner expansion kit (AR-NS2)
This kit is required to add the network scanning feature.
Printer kit (AR-P14)
The Printer Kit is required to upgrade a product whose model name contains suffix "U" (ex. AR-M280U) to network printer. To use such model as network printer, the Printer Kit and Printer Server Card (AR-NC5J) are required.
1-8
PART NAMES AND FUNCTIONS
Operation panel of the main unit
The display and indicators show the current status of the printer. All printer settings are made by using the keys and display panel.
1
Message display
Displays the current status of the printer. [ i ] displayed in any message indicates that the [INFORMATION] key should be pressed.
[ERROR] indicator
Lights up when paper or toner must be added or when a misfeed has occurred in the machine. Blinks when an abnormal condition has occurred in the machine.
[DATA] indicator
Lights up or blinks when print data is being received or output. Also lights up when job data is stored by the job retention function (page 2-9).
[READY] indicator
Print data can be received when this indicator is lit.
[MENU] key
Press to select a menu group such as printer configuration menu (page 3-2), custom settings (page 3-6) or execution of print jobs held by the retention function (page 2-9). Also, press to return to the job status screen from the setting screen of each job status group.
[ / ] keys
Press to select menu or function items or to set numerical values for those items.
[BACK/C] key
Use this key to return to the previous screen in each menu selection, to cancel and delete the current job or to delete a reserved job that has been selected.
[OK] key
Press to register the selected menu or function.
[INFORMATION] key
When [ i ] is displayed with a message indicating a paper misfeed, the relevant operation procedure can be displayed by pressing the [INFORMATION] key. If the [INFORMATION] key or the [BACK/C] key is pressed while the operation procedure is displayed, the information mode will be canceled. If you press and hold down this key while printing is being performed or in standby, the total number of printed pages and quantity of toner remaining (as a percentage) will be displayed.
1-9
PART NAMES AND FUNCTIONS
Menu group and explanation of the use of the keys on the main unit operation panel
The menu groups are classified into five groups and are selected consecutively by pressing the [MENU] key. If the [OK] key is pressed when the desired menu screen is displayed, a message will appear to indicate the next required operation.
READY.
[MENU] key
Job status screen
The message "WARMING UP" will be displayed when the power is turned on and a list of the current job plus reserved jobs or a list of completed jobs will be displayed on the job status screen. Examples of the various messages which will be displayed are shown below. (Display example)
WARMING UP.
READY.
FROM TRAY #
CHANGE THE TONER CARTRIDGE.
PAPER JAM.
ADD PAPER.*
[ADD PAPER]
*
When the status display shows [ADD PAPER], paper is required to complete a job in progress. In this case, printing of the job will be suspended until the required paper is added or another paper is selected (see "Setting the paper size and type" on page 1-19). While a current job is suspended, the printer will print a reserved job if paper is available from another source for that job but will not print any other jobs.
The printer is warming up.
The printer is ready to print.
The printer is currently printing. Out of toner. Replace the toner
cartridge. See the separate operation manual entitled "Operation Manual (Read this document before installing the product.)".
A misfeed has occurred. (See page 4-2.)
Out of paper. Load paper. (See page 1-16.)
PRINT JOBS ON HOLD
[MENU] key
SET OPERATIONS CONDITIONS
[MENU] key
CUSTOM SETTINGS
[MENU] key
KEY OPERATOR PROGRAMS
[MENU] key
1-10
Print hold
If the job retention function is used from your computer, print data will be stored in the printer as a hold job. The job retention function can be used only if the printer is equipped with a hard disk drive unit. (See page 2-9.)
Condition settings
The printer condition settings are used for basic printer settings. (See page 3-2.)
Custom settings
Custom settings are used to make settings based on use patterns. (See page 3-6.)
Key operator programs
These are settings used by key operators (administrators of this product). For the use of these programs, see page 6-1.
PART NAMES AND FUNCTIONS
Canceling a print job and deleting print data
●●
●●
To cancel a print job in progress and delete the print data:
Press the [BACK/C] key during printing. Printing will stop and a message asking for confirmation to delete the job will appear. To delete the data, press the [OK] key. To cancel deletion, press the [BACK/C] key. Printing will resume.
●●
●●
To delete print data of a reserved job (jobs stored in the printer):
Print data transmitted from computers will be stored in this printer (up to 99 jobs) and will be printed sequentially. To delete print data of a reserved job before starting printing, press the [ message display. If you press the [BACK/C] key at this time, a confirmation message for deletion will appear. To delete the data, press the [OK] key. To cancel deletion, press the [BACK/C] key. Printing will resume.
] or [ ] key to display the desired data in the
1
1-11
PART NAMES AND FUNCTIONS
Operation panel of the scanner module
When the printer is equipped with a scanner module, the operation panel on the main unit will become inoperative and the panel on the scanner module must be used.
Touch panel
The machine status, messages and touch keys are displayed on the panel. The display will change to show the status of print, copy, network scan or fax according to which of those modes is selected. For details see the next page.
Mode select keys and indicators
Use to switch the display mode of the touch panel.
[PRINT] key/READY indicator/DATA indicator
Press to enter the print mode. (See next page.)
●●
●●
READY indicator
Print data can be received when this indicator is lit.
●●
●●
DATA indicator
Lights up or blinks when print data is being received. Also lights up or blinks when printing is being performed.
[IMAGE SEND] key/LINE indicator/DATA
indicator
Press to enter the network scan/fax mode. (See the facsimile operation manual.)
[JOB STATUS] key
Press to display the current job status. (See page 1-14.)
[CUSTOM SETTINGS] key
Use to adjust the contrast of the touch panel or to set key operator programs. (See page 3-6.)
Numeric keys
Use to enter number values for various settings.
[ ] key ([ACC.#-C] key)
Use for account control for copying and fax sending.
[#/P] key*
This key is used as a program key for copy features and in dialing for fax features.
[C] key*
This key is active for copy and fax features.
Start key*
Use to start copying and fax jobs.
[COPY] key
Press to select the copy mode.*
1-12
[CA] key*
Functions in the copy and fax modes.
* See the operation manual for copier operation.
PART NAMES AND FUNCTIONS
Touch panel (on the scanner module)
Print mode screen
This screen is displayed when the print mode is selected. (The display varies with the mode. For the display in other modes, see their respective operation manuals.)
SELECT JOB.
PRINT HOLD JOB LIST
1
Sharp 005
Sharp 006
Message display
Job status screen (See next page.)
Print hold job list
If the job retention function (see page 2-9) is used, the list of stored print jobs is displayed here (up to 100 jobs). The job retention function can be used only if the printer is equipped with a hard disk drive unit. If the main switch is turned off, stored print data will be cleared.
Microsoft Word - Test001
EXCEL1
1/1
CONDITION
SETTINGS
Display scroll keys
Use these keys to view the job hold list when it is contained on more than one screen.
[CONDITION SETTINGS] key
Use to switch the display to the printer configuration menu (see page 3-2).
1-13
PART NAMES AND FUNCTIONS
Job status screen (common to print, copy, network scan, and fax modes)
This screen is displayed when the [JOB STATUS] key on the operation panel is pressed. A job list showing the current job at the top of the job queue or a list showing completed jobs can be displayed. The contents of the jobs can be viewed, moved up to the highest priority in the job queue or deleted from the queue.
JOB QUEUE
COPY
SHARP001
054234
SETS / PROGRESS
003 / 000
003 / 000
010 / 000
PRINT JOB E-MAIL/FTP FAX JOB
Job list
A job list which indicates the current job and reserved jobs or a job list which indicates completed jobs is displayed. The icons to the left of the jobs in queue represent the job mode.
Print mode Copy mode
Network scan mode
Fax mode Fax mode
(transmission job) (reception job)
When a job list which indicates the current job and reserved jobs is displayed, the displayed jobs themselves are operation keys. To cancel printing or to give a job the highest print priority, touch the relevant job key to select the job and execute the desired operation using the keys described in
, and .
* “PAPER EMPTY” in the job status display
When a job status display indicates “PAPER EMPTY”, the specified size paper is not loaded in any tray to run that job. In this case, printing is suspended for that job until the required paper is loaded. Until the required paper is loaded another reserved job data will be printed if possible. (If paper runs out during printing, another job will not be printed.) If you wish to change the paper size because you do not have the specified size paper, you can change the size by touching the current job key to select it and touch the [DETAIL] key described in
.
1-14
STATUS
COPYING
PAPER EMPTY*
WAITING
Mode switching key
Use to switch the job list between “JOB QUEUE” and “COMPLETE”. “JOB QUEUE”: Displays the list of the current job
“COMPLETE”: Displays the list of completed jobs.
[PRINT JOB] key
Use to display the print job list for all modes (print, copy, network scan, and fax).
[E-MAIL/FTP] key
Use to display the list of jobs that use the network for sending e-mail by SNMP protocol or sending to an ftp site or desktop by ftp protocol.
[FAX JOB] key
Use to display the fax communication status and
,
the reserved transmission job status.
Display switching keys
Use to switch the page of the displayed job list.
[STOP/DELETE] key
Use to cancel or delete the current job or delete the selected reserved job. Received fax print jobs that have been reserved, however, cannot be deleted.
[PRIORITY] key
If you select a job among the reserved jobs in the “JOB QUEUE” job list to which you wish to give the highest priority and touch this key, the job will move to the highest priority reserved job.
[DETAIL] key
Use to display the detailed information of the selected job. The paper size for printing can be changed from the specified size.This function, however, cannot be used when a fax reception print job is selected.
1/1
JOB QUEUE
COMPLETE
DETAIL
PRIORITY
STOP/DELETE
and the reserved jobs.
Using the touch panel
JOB QUEUE
SETS / PR
SHARP001
054234
COPY
003 / 00
010 / 00
003 / 00
1/13
COMPLETE
MULTI SHOT
DUAL PAGE
COPY
SPECIAL MODES
2-SIDED COPY
OUTPUT
READY TO SCAN FOR COPY.
READY TO SEND.
AUTO
EXPOSURE
STANDARD
RESOLUTION
PROGRAMMED
FILE FORMAT
AUTO
ORIGINAL
PART NAMES AND FUNCTIONS
■■
How to use the touch panel
■■
[Example 1]
Items on the touch panel are easily selectable by touching the key associ­ated with the item with a finger. Selection of an
Beep
tone
[Example 2]
The confirmation beeps can be disabled by a key operator program. (See page 6-9.)
item will be accompanied with a beep tone to confirm the item was selected. Also, the key area for the item will be highlighted for visual confirmation.
Keys which are grayed out on any screen are not selectable. If a grayed out key is touched, a double beep will be sounded.
■■
Selection of function
■■
[Example 1]
010 / 000
1
8
2
11
1.
1
8
2
11
2.
11
17
3.
Items which are highlighted at the time a screen appears are already selected and will be registered to function if the [OK] key is touched.
[Example 2]
Copier feature Facsimile feature
WAITING
PLAIN
TRANSPARENCY
PLAIN
When the machine is used in the copy or fax modes, the functions shown below can only be set on the special feature screen. They can be set or cancelled by alternate touches on the panel.
PAPER SELECT
OK
1
Dual page copy Job build
[Example 3]
Polling Dual page scan
When the machine is used in the copy or fax modes and a special feature is selected, a corresponding icon representing the feature will appear on the touch key and on the main screen of the mode selected. If this icon is touched, the setting screen of the function (or a menu screen) will appear, allowing the settings to be checked or adjusted and the function to be canceled easily.
1-15
LOADING PAPER
The message “ADD PAPER” or “OPEN TRAY AND ADD PAPER” will appear when paper runs out during operation. Follow the procedure below to load paper.
NOTES
Do not use curled or folded paper. Doing so may cause a misfeed.
For best results use paper supplied by SHARP. (See page 1-18.)
When you change the paper type and size in paper tray 1, set the paper type and size referring to “Setting the
paper size and type” (page 1-19).
Do not place heavy objects or press hard on any tray which is pulled out.
Loading paper in paper tray 1
Pull out paper tray 1.
1
Load paper into the tray.
2
Gently pull the tray out until it stops.
Do not load paper above the maximum height line (approximately 500 sheets of 20 lbs. paper).
(80 g/m2)
Gently push tray 1 into the machine.
3
Push the tray firmly all the way into the machine.
Set the paper type.
4
If you change the paper type, be sure to set the paper type referring to “Setting the paper size and type” (page 1-19).
Loading paper in paper tray 1 is now
5
complete.
Changing the paper size in paper tray 1
For paper tray 1, 8-1/2" x 11", A4 or B5 size paper can be set. Use the following procedure to change the size as needed.
Pull out paper tray 1.
1
If paper remains in the tray, remove it.
Adjust the guide plates A and B in the tray
2
to the length and width of the paper.
The guide plates A and B are slidable. Adjust them to the paper size to be loaded while squeezing their lock levers.
Load paper into the tray.
3
1-16
Gently push tray 1 into the machine.
4
Push the tray firmly all the way into the machine.
Set the paper size.
5
Be sure to set the paper size and paper type referring to “Setting the paper size and type” (page 1-19). If this is not done, paper misfeeds will occur.
Changing paper size in paper tray 1 is now
6
complete.
Specifications of paper trays
The specifications for types and sizes of paper for loading paper trays are shown below.
Tra y
Paper tray 1
Multi purpose drawer/bypass tray
Stand/3 x 500 sheet paper
Upper Middle
drawer
Lower
Stand/ MPD &
2000
Upper Lower
sheet paper
drawer
Tray No.
(tray name)
Tray 1
Tray 2/bypass tray
Tray 2 Same as multi purpose drawer Tray 3
Tray 4
Tray 2 Same as multi purpose drawer Tray 3
Applicable paper types Applicable paper sizes
Plain paper (Refer to the next page for applicable plain papers.)
Plain paper (Refer to the next page for applicable plain papers.)
8-1/2 x 11, A4, B5
If "AUTO-INCH" is selected in setting the paper size and type (page 1-19), the following paper sizes can be used with the automatic detection function: 11 x 17, 8-1/2 x 14, 8-1/2 x 11, 8-1/2 x 11R, 7-1/4 x 10-1/2R, 5-1/2 x 8-1/2R
If "AUTO-AB" is selected in setting the paper size and type (page 1-19), the following paper sizes can be used with the automatic detection function: A3, B4, A4, A4R, B5, B5R, A5R, 8-1/2 x 13
Non-standard sizes
Special paper (Refer to the next page for applicable special papers.)
Thick paper
Labels, transparency film
If "AUTO-INCH" is selected in setting the paper size and type (page 1-19), the following paper sizes can be used with the automatic detection function: 8-1/2 x 11, 8-1/2 x 11R
If "AUTO-AB" is selected in setting the paper size and type (page 1-19), the following paper sizes can be used with the automatic detection function: A4, A4R, B5, B5R
Non-standard sizes smaller than 8-1/2 x 11 or A4
Postcard Envelopes can
only be fed from the multi-purpose drawer.
Japanese official postcard
Applicable standard size envelopes: COM-10, Monarch, DL, C5, ISO B5
Non-standard size
Applicable paper stock weight for envelopes is 20 to 23 lbs. or 75 to
2
.
90 g/m
Plain paper (Refer to the next page for applicable plain papers.)
If "AUTO-INCH" is selected in setting the paper size and type (page 1-19), the following paper sizes can be used with the automatic detection function: 11 x 17, 8-1/2 x 14, 8-1/2 x 11, 8-1/2 x 11R, 7-1/4 x 10-1/2R
If "AUTO-AB" is selected in setting the paper size and type (page 1-19), the following paper sizes can be used with the automatic detection function: A3, B4, A4, A4R, B5, B5R, 8-1/2 x 13
Plain paper (Refer to the next
8-1/2 x 11, A4
page for applicable plain papers.)
LOADING PAPER
Paper
weight
16 to 28 lbs. or 60 to 105
2
g/m
16 to 34 lbs. or 60 to 128
2
g/m
See the remarks for special paper on the next page.
16 to 28 lbs. or 60 to 105
2
g/m
16 to 28 lbs. or 60 to 105
2
g/m
1
1-17
LOADING PAPER
Applicable plain paper
For satisfactory results, plain paper must conform to the following requirements.
Paper in AB system Paper in inch system
A5 to A3 5-1/2 x 8-1/2 to 11 x 17
Plain paper 16 to 28 lbs. or 60 to 105 g/m
2
Recycled, colored, pre-punched, pre-printed and letterhead papers must conform to the same conditions as above.
Applicable special paper
For satisfactory results, special paper must conform to the following requirements.
Type Remarks
Special paper Thick paper
Transparency film, labels, and tracing paper than SHARP recommended labels. Doing so may leave
Postcards
Envelopes
For 5-1/2 x 8-1/2 to 8-1/2 x 11 or A5 to A4 sizes, thick paper ranging from 16 to 34 lbs. or 60 to 128 g/m
2
can be
used.
For sizes larger than 8-1/2 x 11 or A4, thick paper ranging from 16 to 28 lbs. or 60 to 105 g/m
Other thick papers Index stock (65 lbs. or 176 g/m Cover stock (110 lbs. or 200 to 205 g/m
2
can be used.
2
) can be used.
2
) can be used but
only for 8-1/2 x 11, A4 paper in the portrait orientation.
For 5-1/2 x 8-1/2 or A5 paper, the orientation must be landscape.
Use SHARP recommended paper. Do not use labels other
adhesive residue in the printer, causing paper misfeeds, smudges on prints or other machine trouble.
Japanese official postcards can be used.
Applicable standard envelopes: COM-10, Monarch, DL, C5, ISO B5
Envelopes can only be fed from the multi-purpose drawer. Applicable paper stock weight for envelopes is 20 to 23
2
lbs. or 75 to 90 g/m
.
1-18
LOADING PAPER
Setting the paper size and type
For the specifications for types and sizes of paper for loading paper trays, see page 1-17.
Setting the paper size and type from the operation panel on the main printer
When the paper size or type is changed in a paper tray, set them referring to the following procedure.
Press the [MENU] key repeatedly until
1
“CUSTOM SETTINGS” appears in the message display.
Press the [OK] key.
2
When the [OK] key is pressed,“TRAY SETTING” will appear in the message display.
Press the [OK] key.
3
TRAY SETTING
TRAY1
Select the desired paper tray.
4
Press the [OK] key.
5
The paper size and paper type of the tray selected in step 4 will appear.
LETTER PLAIN
When the [OK] key is pressed,the message shown to the left will appear in the message display.
Press the or key repeatedly until the desired paper tray is indicated in the display.
If TRAY 1 is selected in step 4, the message shown to the left will appear in the display.
Press the [OK] key.
7
To cancel the setting change, press the [BACK/C] key to return to step 4.
Select the paper type that has been set in
8
the tray.
PLAIN OK?
NOTE
Special paper such as thick paper, transparency film, labels, and postcards can be set for tray 2 and the bypass tray. Envelopes can be set only for tray 2.
Press the [OK] key.
9
Ensure that the desired paper size is
10
selected.
LETTER OK?
Depending on the selected tray, a selection for “AUTO-AB” and “AUTO-INCH” may appear. “AUTO-AB”: Select when you have set AB system paper. “AUTO-INCH”: Select when you have set inch system paper. When the paper system is changed from the inch system to the AB system or vise versa, the paper type must be designated. Select the paper type.
If you have set paper of non-standard size, select “NON STANDARD”. This size can be selected when tray 2 or the bypass tray has been selected in step 4.
Press the [OK] key to complete the setting.
11
Press the or key repeatedly until the paper type that has been set appears.
Press the key or key repeatedly until the desired paper size appears.
1
Press the key.
6
CHANGE TRAY1 SETTING OK?
If TRAY 1 is selected in step 4, the message shown to the left will appear in the display.
1-19
LOADING PAPER
TOTAL COUNT
TRAY SETTINGS
TRAY 1
TRAY 2
TRAY 3
PLAIN / AUTO-INCH
RECYCLED / AUTO-INCH
TYPE / SIZE
PLAIN / 8 X11
1
/
2
SIZE
A4
OK
Setting the paper type and size from the touch panel
Press the [CUSTOM SETTINGS] key.
1
The custom setting menu screen will appear.
Press the [TRAY SETTINGS] key.
2
The paper tray selection screen will appear.
Select the paper tray for which the setting
3
is to be made.
“AUTO-INCH”: Select when you have set inch system paper. When the paper system is changed from the inch system to the AB system or vise versa, the paper type must be designated. Select the paper type.
If you have set paper of non-standard size, select “NON STANDARD SIZE”. This size key appears when tray 2 or the bypass tray has been selected in step 3.
Touch the [OK] key to complete the setting.
5
If the desired tray is not on the display, use [ [
] key to scroll the
display until it appears.
Select the paper type and the paper size.
4
If TRAY 1 has been selected in step 3:
CUSTOM SETTINGS TRAY 1 TYPE/SIZE SETTING
TYPE SIZE
PLAIN
PRE-PRINTED
RECYCLED COLOR
The highlighted keys indicate the current selections. To change either type or size or both, touch the desired keys to highlight the selections.
Paper types Special papers such as transparency film and labels can be set for tray 2 and the bypass tray. Envelopes can be set only for tray 2.
LETTER HEAD
PRE-PUNCHED
1
8
2
11
B5
OK
A4
] or
Paper sizes
Depending on the selected tray, a selection for “AUTO-AB” and “AUTO-INCH” may appear. “AUTO-AB”: Select when you have set AB system
1-20
paper.
Loading...
+ 102 hidden pages