In the interests of user-safety (Required by safety regulations in some countries ) the set should be restored to its
original condition and only parts identical to those specified should be used.
Specifications are subject to change without
prior notice.
SHARP CORPORATION
This document has been published to be used for after
sales service only.
The contents are subject to change without notice.
27UF5
IMPORTANT SERVICE SAFETY PRECAUTION
Ë
Service work should be performed only by qualified service technicians who are
thoroughly familiar with all safety checks and the servicing guidelines which follow:
WARNING
1. For continued safety, no modification of any circuit
should be attempted.
2. Disconnect AC power before servicing.
3. Semiconductor heat sinks are potential shock hazards
when the chassis is operating.
4. The chassis in this receiver has two ground systems
which are separated by insulating material. The nonisolated (hot) ground system is for the B+ voltage
regulator circuit. The isolated ground system is for
the low B+ DC voltages and the secondary circuit of
the high voltage transformer.
To prevent electrical shock use an isolation
transformer between the line cord and power
receptacle, when servicing this chassis.
CAUTION: FOR CONTINUED
PROTECTION AGAINST A
RISK OF FIRE, REPLACE
4A 125V
ONLY WITH SAME TYPE 4A125V FUSE.
SERVICING OF HIGH VOLTAGE SYSTEM
AND PICTURE TUBE
When servicing the high voltage system,
remove the static charge by connecting a
10k ohm resistor in series with an insulated
wire (such as a test probe) between the picture tube ground and the anode lead. (AC
line cord should be disconnected from AC
outlet.)
1. Picture tube in this receiver employs integral
implosion protection.
2. Replace with tube of the same type number for
continued safety.
3. Do not lift picture tube by the neck.
4. Handle the picture tube only when wearing
shatterproof goggles and after discharging the high
voltage anode completely.
X-RADIATION AND HIGH VOLTAGE LIMITS
1. Be sure all service personnel are aware of the
procedures and instructions covering X-radiation. The
only potential source of X-ray in current solid state
TV receivers is the picture tube. However, the picture
tube does not emit measurable X-Ray radiation, if
the high voltage is as specified in the "High Voltage
Check" instructions.
It is only when high voltage is excessive that Xradiation is capable of penetrating the shell of the
picture tube including the lead in the glass material.
The important precaution is to keep the high voltage
below the maximum level specified.
2. It is essential that servicemen have available at all
times an accurate high voltage meter.
The calibration of this meter should be checked
periodically.
3. High voltage should always be kept at the rated value
−no higher. Operation at higher voltages may cause
a failure of the picture tube or high voltage circuitry
and;also, under certain conditions, may produce
radiation in exceeding of desirable levels.
4. When the high voltage regulator is operating properly
there is no possibility of an X-radiation problem. Every
time a color chassis is serviced, the brightness should
be tested while monitoring the high voltage with a
meter to be certain that the high voltage does not
exceed the specified value and that it is regulating
correctly.
5. Do not use a picture tube other than that specified or
make unrecommended circuit modifications to the
high voltage circuitry.
6. When trouble shooting and taking test measurements
on a receiver with excessive high voltage, avoid being
unnecessarily close to the receiver.
Do not operate the receiver longer than is necessary
to locate the cause of excessive voltage.
2
22
IMPORTANT SERVICE SAFETY PRECAUTION
1.5k ohm
10W
0.15 F
TEST PROBE
TO EXPOSED
METAL PARTS
CONNECT TO
KNOWN EARTH
GROUND
(Continued)
27UF5
BEFORE RETURNING THE RECEIVER
(Fire & Shock Hazard)
Before returning the receiver to the user, perform
the following safety checks.
1. Inspect all lead dress to make certain that leads are
not pinched or that hardware is not lodged between
the chassis and other metal parts in the receiver.
2. Inspect all protective devices such as non-metallic
control knobs, insulating materials, cabinet backs,
adjustment and compartment covers or shields,
isolation resistor-capacity networks, mechanical
insulators, etc.
3. To be sure that no shock hazard exists, check for
leakage current in the following manner.
• Plug the AC cord directly into a 120 volt AC outlet,
(Do not use an isolation transformer for this test).
• Using two clip leads, connect a 1.5k ohm, 10 watt
resistor paralleled by a 0.15µF capacitor in series with
all exposed metal cabinet parts and a known earth
ground, such as electrical conduit or electrical ground
connected to earth ground.
• Use an AC voltmeter having with 5000 ohm per volt,
or higher, sensitivity to measure the AC voltage drop
across the resistor.
• Connect the resistor connection to all exposed metal
parts having a return to the chassis (antenna, metal
cabinet, screw heads, knobs and control shafts,
escutcheon, etc.) and measure the AC voltage drop
across the resistor.
AII checks must be repeated with the AC line cord
plug connection reversed. (If necessary, a nonpolarized adapter plug must be used only for the
purpose of completing these check.)
Any current measured must not exceed 0.5 milliamp.
Any measurements not within the limits outlined
above indicate of a potential shock hazard and
corrective action must be taken before returning the
instrument to the customer.
Many electrical and mechanical parts in television
receivers have special safety-related characteristics.
These characteristics are often not evident from visual
inspection, nor can protection afforded by them be
necessarily increased by using replacement components
rated for higher voltage, wattage, etc.
Replacement parts which have these special safety
characteristics are identified in this manual; electrical
components having such features are identified by "å"
and shaded areas in the Replacement Parts Lists and
Schematic Diagrams.
For continued protection, replacement parts must be
identical to those used in the original circuit. The use of
substitute replacement parts which do not have the same
safety characteristics as the factory recommended
replacement parts shown in this service manual, may
create shock, fire, X-radiation or other hazards.
3
27UF5
g
LOCATION OF USER'S CONTROL
Front Panel
POWER
Press → On.
Press again → Off.
REMOTE CONTROL
SENSOR
MENU
Press → Accesses MAIN MENU.
Press again → Exits MAIN MENU.
Basic Remote Control Functions
POWER
Press → On.
Press again → Off.
REMOTE KEYPAD
Accesses any channel from keypad.
FLASHBACK
Returns to previous channel.
PERSONAL PREFERENCE
With the Personal Preference buttons, you
can program your favorite programs by
using the 4 categories A, B, C and D. The
channels can be accessed quickly by using
these buttons.
VOLUME UP/DOWN
+) Increases sound.
(
(—) Decreases sound.
• Changes or selects the TV
adjustments on On-Screen Display.
MENU
Press → Accesses MAIN MENU.
Press again → Exits MAIN MENU.
MUTE
Press → Mutes sound.
Press again → Restores sound.
• When sound is muted, CLOSED
CAPTION appears if available.
POWER (DVD/VCR)
Press → On.
Press again → Off.
DVD/VCR CONTROL
VOLUME UP/DOWN
+) Increases sound.
(
(—) Decreases sound.
INSIDE DOOR
VIDEO/AUDIO
TERMINALS
CHANNEL UP/DOWN
(') Selects next higher channel.
(") Selects next lower channel.
Infrared Transmitter Window
CATV/DVD-TV/VCR MODE buttons
Press TV/VCR → Signals sent will be for
TV and VCR control.
Press CATV/DVD → Signals sent will be
for cable TV converter and DVD control.
DISPLAY
Press → Displays receiving channel for
4 seconds.
Press again → Removes display.
• Temporarily displays receiving channel
when in Closed Caption mode.
INPUT
Press → Switches to external video
INPUT 1 mode.
Press twice → Switches to external video
INPUT 2 mode.
Press 3 times → Switches to external
video INPUT 3 mode or COMPONENT
mode.
Press 4 times → Switches back to the
original TV mode.
ENTER
Used in some instances where a Cable
Converter Box requires an “enter” command
after selecting channels, when using the
REMOTE KEYPAD button.
CHANNEL UP/DOWN
(') Selects next higher channel.
(") Selects next lower channel.
• Moves the “” mark on the MENU
screens.
IN 2
SKIP/VCR-CH
REC
Note:
• The above shaded buttons on the Remote Control glow in the dark. To use the glow-in-the-dark display on the
remote control, place it under a fluorescent light or other lighting.
• The phosphorescent material contains no radioactive or toxic material, so it is safe to use.
• The degree of illumination will vary depending on the strength of lighting used.
• The degree of illumination will decrease with time and depending on the temperature.
• The time needed to charge the phosphorescent display will vary depending on the surrounding lighting.
• Sunli
ht and fluorescent lighting are the most effective when charging the display.
4
INSTALLATION AND SERVICE INSTRUCTIONS
Note:(1) When performing any adjustments to resistor controls and transformers use non-metallic
screwdrivers or TV alignment tools.
(2) Before performing adjustments, the TV set must be on at least 15 minutes.
27UF5
CIRCUIT PROTECTION
The receiver is protected by a 4.0A fuse (F701),
mounted on PWB-A, wired into one side of the AC
line input.
X-RADIATION PROTECTOR CIRCUIT TEST
After service has been performed on the horizontal
deflection system, high voltage system, B+ system,
test the X-Radiation protection circuit to ascertain
proper operation as follows:
1. Apply 120V AC using a variac transformer for accurate
input voltage.
2. Allow for warm up and adjust all customer controls
for normal picture and sound.
3. Receive a good local channel.
4. Connect a digital voltmeter to TP651 (Pin 3) and make
sure that the voltmeter reads 13.85 ±0.6V DC.
5. Apply external 17.3V DC at TP651 by using an
external DC supply, TV must be shut off.
6. To reset the protector, unplug the AC cord and plug
the AC cord power on. Now make sure that normal
picture appears on the screen.
7. If the operation of the horizontal oscillator does not
stop in step 5, the circuit must be repaired before the
set is returned to the customer.
HIGH VOLTAGE CHECK
High voltage is not adjustable but must be checked
to verify that the receiver is operating within safe
and efficient design limitations as specified checks
should be as follows:
1. Connect an accurate high voltage meter between
ground and anode of picture tube.
2. Operate receiver for at least 15 minutes at 120V AC
line voltage, with a strong air signal or a properly tuned
in test signal.
3. Enter the service mode and select the service
adjustment "V18" and Bus data "01" (Y-mute on, CRT
Cut Off).
4. The voltage should be below 31.5kV (at zero beam).
If a correct reading cannot be obtained, check circuitry
for malfunctioning components. After the voltage test,
make Y-mute off to the normal mode.
5
27F630
27F631
For adjustments of this model, the bus data is converted to various analog signals by the D/A converter
circuit.
Note: There are still a few analog adjustments in this series such as focus and master screen voltage.
Follow the steps below whenever the service adjustment is required. See "Table-B" to determine, if service adjustments are required.
1. Service mode
Before putting unit into the service mode, check that
customer adjustments are in the normal mode. Use
the reset function in the video adjustment menu to
ensure customer controls are in their proper (reset)
position.
2. Service number selection
Once in the service mode, press the Ch-up or Chdown button on the remote controller or at the set.
The service adjustment number will vary in
increments of one, from "V01" to "P08". Select the
item you wish to adjust.
3. Data number selection
Press the Vol-up or Vol-down button to adjust the data
number.
DATA NUMBER
SERVICE ADJUSTMENT NUMBER
To enter the service mode and exit service mode.
To enter the service mode manually just press and hold
the Vol-down and Ch-up buttons at the same time, plug
the AC cord into a wall socket.
Now the TV set is switched on and enters the service
mode.
To exit the service mode, turn the television off by
pressing the power button.
P08TINT-PIP-INPUT0-63 (00h-3Fh)36 (24h)External input for sub screen24
Table - A
8
27UF5
A
B
Holding down both the VOL-up and CH-up buttons on the TV set at service mode for more than 2 seconds will
automatically write the above initial values into IC2101.
PART REPLACED
IC2001
IC201
IC2101
CRT
IC3001
IC1801
NECESSARYUNNECESSARY
ADJUSTMENT
X
X
X
X
X
NOTES
X
Data is stored in IC2101.
The adjustment is needed to compensate for characteristics of parts
including IC201 and MTS level (M01).
Holding down both the VOL-up and CH-up buttons on the TV set in
the service mode for more than 2 seconds will automatically write the
above initial values into IC2101 Then perform a complete adjustment.
Adjust items related to picture tube only.
Adjust items related to MTS only (M01~M20).
Adjust items related to P-IN-P only (P01~P08).
Table - B
SERVICE ADJUSTMENT
RF AGC Adjustment
1. Receive a good local channel.
2. Enter the service mode and select the service
adjustment "R01".
3. Set the data value to point where no noise or beat
appears.
4. Select another channel to confirm that no noise or
beat appears.
Note 1 : You will have to come out of the service
mode to select another channel.
Note 2 : Setting the data to "00" will produce a black
raster.
Screen Adjustment
1. Receive a good local channel.
2. Enter the service mode and select the service
adjustment "V03" and set the data value to "00" to
set the color level to minimum. (Record original data
code under adjustment "V03" before changing) You
may skip this step, if you selected a B/W picture or
monoscope pattern.
3. Select the service adjustment "V11" and adjust the
data value to "01", this turn off the luminance signal
(Y-mute).
4. Adjust the master screen control until the raster
darkens to the point where raster is barely seen.
5. Adjust the service adjustments "V06" red, "V07" green
and "V08" blue to obtain a good grey scale with
normal whites at low brightness level.
6. Select the service adjustment "V11" and reset data
to "00". Select the service adjustment "V03" and reset
data to obtain normal color level.
7. For component input, the data value of "V46" red,
"V47" green and "V48" blue is adjusted to follow the
data value of "V06", "V07" and "V08" respectively.
8. Reset the master screen control to obtain normal
brightness range.
White Balance Adjustment
1. Receive a good local channel.
2. Enter the service mode and select the service
adjustment "V03" and set to "00" (minimum
color)(Record original data code under adjustment
"V03" before changing). "V03" does not have to be
adjusted, if you selected a B/W picture or monoscope
pattern.
3. Alternately adjust the service adjustment data of
"V09" and "V10" until a good grey scale with normal
whites is obtained. (RF Input)
4. For component input, the data value of "V49" and
"V50" is adjusted to follow the data value of "V09"
and "V10" respectively.
5. Select the service adjustment "V03" and reset data
to obtain normal color level.
Sub-picture and Sub-Bright Adjustments
1. Receive the window pattern signal.
• RF INPUT (TU51)
2. Get into service adjustment data "V01" and "V05" and
set the luminance as shown in figure "A" and "B" as
below respectively.
• COMPONENT INPUT
3. Get in service adjustment data "V42" and "V45" and
set the luminance as shown in figure "A" and "B" as
below respectively.
LUMINESCENCE CONFIRMATION
A: 120±10cd/m
B:1.5±0.5cd/m
2
2
9
27UF5
Sub-Tint Adjustment
1. Receive the half color bar signal.
• RF INPUT (TU51)
2. Get into Y-Mute by R/C, or by setting the "V11" bus
data to "01".
3. Vary the "V02" bus data until the waveform becomes
as stated below.
LEVEL
B-AMP Base waveform in step
(TP47B)
Sub-Color Adjustment
1. Receive a good local channel.
2. Make sure the customer color control is set to center
position .
• RF INPUT (TU51)
3. Enter the service mode and select service adjustment
"V03".
4. Adjust "V03" data value to obtain a normal color level.
Focus Adjustment
1. Receive a good local channel.
2. Adjust the FOCUS VR of the flyback transformer to
make the image as fine as possible.
C. C Display Position Adjustment
1. Receive the lion head pattern signal.
2. Select "EX2" to display the text box.
3. Adjust the "EX2" bus data to let the text box displayed
in the center.
DISPLAY OF TEXT BOX
TEXT BOX
| A-B | / 2
Note: Aging for 10 min before adjustment. After the
adjustment of V-center and V-size, readjustment for this V-line.
Vertical Phase Adjustment
(SCREEN FORMAT 4:3)
1. Enter the service mode and input D.
2. Adjust "D18" data value so that picture is centered.
(SCREEN FORMAT 16:9)
3. Input data of "00h" on "D20".
4. Input data of "D34" same as "D18" data.
Horizontal Position Adjustment
1. Receive a good local channel.
(SCREEN FORMAT 4:3)
2. Enter the service mode and select the service
adjustment "D02".
3. Adjust "D02" data value so that picture is centered.
(SCREEN FORMAT 16:9)
4. Input data of "D21" same as "D02" data.
Horizontal-Size Adjustment
1. Receive a good local channel.
(SCREEN FORMAT 4:3)
2. Enter the service mode and select the service
adjustment "D04" for H-size.
3. Adjust the "D04" bus data to get the proper H-size.
(SCREEN FORMAT 16:9)
4. Input data of "D23" same as "D04" data.
EW-Parabola
1. Receive a good local channel.
(SCREEN FORMAT 4:3)
2. Enter the service mode and select the service
adjustment "D07" for EW parabola.
3. Adjust the "D07" bus data to get the proper vertical
straight line for both left and right side.
(SCREEN FORMAT 16:9)
4. Input data of "D26" to mines 21 step from "D07" data.
A
SPEC INSPECTION:| A-B | / 2
B
<
5mm
=
Vertical-Size and Linearity Adjustments
1. Receive a good local channel.
(SCREEN FORMAT 4:3)
2. Enter the service mode and select the service
adjustment "D03" for V-size.
3. Adjust the "D03" bus data to get the proper V-size.
4. For V-linearity adjustment, select data bus "D05" and
adjust to get the proper vertical linearity.
(SCREEN FORMAT 16:9)
5. Input data of "D22" to mines 38 step from "D03” data.
(V-SIZE)
6. Input data of "D24" same as "D05" data. (V-LIN)
EW-Trapezium
1. Receive a good local channel.
(SCREEN FORMAT 4:3)
2. Enter the service mode and select the service
adjustment "D08" for EW-Trapezium.
3. Adjust the "D08" bus data to get the best position
display.
(SCREEN FORMAT 16:9)
4. Input data of "D27" same as "D08" data.
10
Ë
MTS ADJUSTMENT
MTS Level Adjustment
1. Set the sound volume above 1.
Monoral signal: 400Hz, 100% modulation
2. Confirm "EX4" data is "5Ah".
3. Vary the "M01" bus data until the voltage to pin (39)
of IC3001 to become the value as stated below.
SETTING VOLTAGE
ADJ spec : 490±10mVrms
CHK spec: 490±20mVrms
MTS VCO Adjustment
1. Keep the unit in no-signal state.
2. Connect the frequency counter to pin (39) of IC3001.
3. Connect a capacitor (100µF, 50V) in between
positive(+) side of C3005 and ground.
4. Enter the service mode and select the service
adjustment "M02"
5. Adjust the data so that the frequency counter reads
62.94 ±0.75kHz.
27UF5
Filter Adjustment
1. Feed the following stereo pilot signal to pin (14) of
IC3001 at C3005 open.
Stereo pilot signal: 9.4kHz, 600mVrms.
2. Enter the service mode and select the service
adjustment "M03".
3. Adjust the data until "OK" appears in position on the
screen. Make sure the "OK" is displayed almost at
the center of the data range.
Separation Adjustment
1. Input "SIGNAL 1" and vary the "M04" bus data to get
the minimun AC voltage to pin (39) of IC3001.
2. Input "SIGNAL 2" and vary the "M05" bus data to get
the minimun AC voltage to pin (39) of IC3001.
SIGNAL 1:
SIGNAL 2: 3kHz, 30% modulation, Lch only, NR-ON
Note: SIGNAL 1 Adj. for widebando
SIGNAL 2 Adj. for spectral
Check the output of the speaker at the maximum
volume as stated below.
Confirmation spec:
ADJ spec: above 25 dB
CHK spec: above 20 dB
300Hz, 30% modulation, Lch only, NR-ON
11
27UF5
CHASSIS LAYOUT
H
G
F
E
D
C
B
A
654321
12
BLOCK DIAGRAM
H
G
F
27UF5
E
D
C
B
A
654321
13
27UF5
DESCRIPTION OF SCHEMATIC DIAGRAM
NOTES:
1. The unit of resistance "ohm" is omitted.
(K=kΩ=1000Ω, M=MΩ)
2. All resistors are 1/16 watt, unless otherwise noted.
3. All capacitors are µ F, unless otherwise noted.
(P=pF=µµF)
4. (G) indicates ±2% tolerance may be used.
5.
indicates line isolated ground.
VOLTAGE MEASUREMENT CONDITIONS:
1. All DC voltages are measured with DVM connected
between points indicated and chassis ground, line
voltage set at 120V AC and all controls set for normal
picture unless otherwise indicated.
2. All voltages measured with 1000µ V B & W or Color
signal.
WAVEFORMS
WAVEFORM MEASUREMENT CONDITIONS:
1. Photographs taken on a standard gated color bar
signal, the tint setting adjusted for proper color. The
wave shapes at the red, green and blue cathodes of
the picture tube depend on the tint, color level and
picture control.
2.
indicates waveform check points (See chart,
waveforms are measured from point indicated to
chassis ground.)
å
AND SHADED ( ) COMPONENTS
= SAFETY RELATED PARTS.
ç
MARK= X-RAY RELATED PARTS.
This circuit diagram is a standard one, printed circuits
may be subject to change for product improvement
without prior notice.
Replacement parts which have these special safety characteristics identified in this manual ; electrical components having such features are
identified by å and shaded areas in the Replacement Parts Lists and
Schematic Diagrams. The use of a substitute replacement part which
does no have the same safety characteristic as the factory recommended replacement parts shown in this service manual may create
shock, fire or other hazards.
"HOW TO ORDER REPLACEMENT PARTS"
To have your order filled promptly and correctly, please furnish the following informations.
1. MODEL NUMBER2. REF. NO.
3. PART NO.4. DESCRIPTION
in USA: Contact your nearest SHARP Parts Distributor to order. For
location of SHARP Parts Distributor, Please call Toll-Free; 1800-BE-SHARP
★ MARK: SPARE PARTS-DELIVERY SECTION
' MARK: X-RAY RELATED PARTS
Ref. No.Part No.★DescriptionCode
PICTURE TUBE
'åV101 VB68LXZ696X1EX Picture TubeCF
å L703RCILG0056PEZZX Degaussing CoilAS
åQEARCA010WJZZ X Grounding StrapAD
Q201 VS2SC2735//1E∗X 2SC2735AB
Q361 VS2SB709AR/-1∗ X 2SB709ARAA
Q401 VS2SD601AR/-1∗ X 2SD601ARAA
Q402 VS2SB709AR/-1∗ X 2SB709ARAA
Q403 VS2SD601AR/-1∗ X 2SD601ARAA
Q404 VS2SD601AR/-1∗ X 2SD601ARAA
Q451 VS2SA1266-Y-1+X 2SA1266-YAB
Q460 VSRT1N441C/-1∗ X RT1N441CAA
Q471 VS2SD601AR/-1∗ X 2SD601ARAA
Q472 VS2SD601AR/-1∗ X 2SD601ARAA
Q473 VS2SD601AR/-1∗ X 2SD601ARAA
Q601 VS2SC2482//-1+X 2SC2482AB
Q751 VS2SC3198-G-1+ X 2SC3198-GAB
Q755 VS2SD601AR/-1∗ X 2SD601ARAA
Q756 VS2SD601AR/-1∗ X 2SD601ARAA
Q757 VS2SC3198-G-1+ X 2SC3198-GAB
Q758 VS2SA1266-Y-1+X 2SA1266-YAB
Q770 VS2SC3333//-1+X 2SC3333AB
Q771 VS2SA1091-O1A+ X 2SA1091-O1AAC
Q802 VS2SD601AR/-1∗ X 2SD601ARAA
Q901 VS2SD601AR/-1∗ X 2SD601ARAA
Q902 VS2SD601AR/-1∗ X 2SD601ARAA
Q903 VS2SD601AR/-1∗ X 2SD601ARAA
Q904 VS2SD601AR/-1∗ X 2SD601ARAA
Q905 VS2SD601AR/-1∗ X 2SD601ARAA
Q906 VS2SD601AR/-1∗ X 2SD601ARAA
Q907 VS2SD601AR/-1∗ X 2SD601ARAA
Q908 VS2SB709AR/-1∗ X 2SB709ARAA
Q910 VS2SB709AR/-1∗ X 2SB709ARAA
Q2060 VS2SD601AR/-1∗ X 2SD601ARAA
Q2201 VS2SD601AR/-1∗ X 2SD601ARAA
Q2211 VS2SD601AR/-1∗ X 2SD601ARAA
27
D52RH-EX0676GEZZ∗ X Zener Diode, 32VAB
DIODES
D103 RH-DX0441CEZZ∗ X DiodeAA
D361 VHD1SS119//-1∗X 1SS119AA
D362 VHD1SS119//-1∗X 1SS119AA
D410 RH-EX0611GEZZ∗ X Zener Diode, 5.1VAB
D411 RH-EX0611GEZZ∗ X Zener Diode, 5.1VAB
D412 RH-EX0614GEZZ∗ X Zener Diode, 5.6VAB
D413 RH-EX0614GEZZ∗ X Zener Diode, 5.6VAB
D414 RH-EX0614GEZZ∗ X Zener Diode, 5.6VAB
D454 RH-EX0628GEZZ∗ X Zener Diode, 8.2VAB
C681 VCFPFA2EB364JX 0.36250V M.PolyproAB
C682 VCKYPA2HB102K+ X 1000p 500V CeramicAB
C685 VCQYTA1HM333J+ X 0.033 50VMylarAA
å C701 RC-FZA022WJZZX 0.22
C702 RC-KZ0029CEZZ+ X 0.01
C703 RC-KZ0029CEZZ+ X 0.01
å C705 RC-EZ0719CEZZX 560200V Electrolytic
å C706 RC-KZ0089GEZZA X 1000p
å C707 RC-KZ0092GEZZA X 3300p
å C723 RC-EZ0724CEZZX 100160V ElectrolyticAC
å C725 RC-EZA064WJZZ X 220160V ElectrolyticAD
C726 RC-KZ0226CEZZ+ X 560p 2kVCeramicAB
C727 RC-KZ0226CEZZ+ X 560p 2kVCeramicAB
C729 VCEA0A1HW106M+X 1050VElectrolyticAA
C730 VCEA4A1VN108M+ X 1000 35VElectrolyticAC
C731 RC-EZ0385CEZZ+ X 1000 16VElectrolyticAB
C732 VCKYPA2HB102K+ X 1000p 500V CeramicAB
C733 VCKYPA2HB102K+ X 1000p 500V CeramicAB
C734 VCKYPA2HB471K+ X 470p 500V CeramicAB
C735 VCKYPA2HB471K+ X 470p 500V CeramicAB
C736 VCKYCY1HF103Z∗ X 0.01 50VCeramicAA
C737 VCEA0A1HW226M+X 2250VElectrolyticAA
C738 VCFPVC3CA102H X 1000p 1.6kV M.PolyproAB
C739 RC-EZ0385CEZZ+ X 1000 16VElectrolyticAB
C740 VCEA0A1HW476M+X 4750VElectrolyticAB
C741 VCEA4A2AN105M+ X 1100V ElectrolyticAB
C743 RC-KZ0036CEZZ+ X 330p 2kVCeramicAB
C744 VCKYPA2HB471K+ X 470p 500V CeramicAB
C745 VCKYPA2HB102K+ X 1000p 500V CeramicAB
C746 VCKYPA2HB102K+ X 1000p 500V CeramicAB
C747 VCEA0A1HW475M+X 4.750VElectrolyticAA
C749 VCEA0A1HW105M+X 150VElectrolyticAA
C753 RC-KZ0036CEZZ+ X 330p 2kVCeramicAB
C754 VCKYPA2HB472K+ X 4700p 500V CeramicAB
C755 VCEA0A1EW476M+X 4725VElectrolyticAA
C783 VCQYTA1HM103J+ X 0.01 50VMylarAA
C784 VCKYCY1HF103Z∗ X 0.01 50VCeramicAA
C801 VCCCCY1HH110J∗ X 11p50VCeramicAA
C802 VCKYCY1HB222K∗ X 2200p 50VCeramicAA
C803 VCEA0A1HW224M+X 0.22 50VElectrolyticAA
C804 VCKYCY1CF104Z∗ X 0.116VCeramicAA
C805 VCEA0A0JW108M+ X 1000 6.3V ElectrolyticAB
C806 VCKYCY1CF104Z∗ X 0.116VCeramicAA
C807 VCKYCY1CF104Z∗ X 0.116VCeramicAA
C808 VCKYCY1CF104Z∗ X 0.116VCeramicAA
C809 VCKYCY1CF104Z∗ X 0.116VCeramicAA
C810 VCEA0A1CW477M+X 47016VElectrolyticAB
C812 VCQYTA1HM104J+ X 0.150VMylarAB
C901 VCKYCY1HB103K∗ X 0.0150VCeramicAA
C902 VCKYCY1HB103K∗ X 0.0150VCeramicAA
AC250V
AC250V
CeramicAB
AC250V
CeramicAB
AC250V
CeramicAB
AC250V
CeramicAB
AB
C903 VCKYCY1HB681K∗ X 680p 50VCeramicAA
C904 VCEA0A1HW105M+X 150VElectrolyticAA
C905 VCEA0A1HW105M+X 150VElectrolyticAA
C906 VCKYCY1HB681K∗ X 680p 50VCeramicAA
C907 VCEA0A1HW105M+X 150VElectrolyticAA
C908 VCKYCY1HB103K∗ X 0.01 50VCeramicAA
C909 VCEA0A1HW105M+X 150VElectrolyticAA
C910 VCEA0A1HW105M+X 150VElectrolyticAA
C911 VCEA0A1HW105M+X 150VElectrolyticAA
C912 VCEA0A1HW105M+X 150VElectrolyticAA
C913 VCEA0A1HW105M+X 150VElectrolyticAA
C914 VCKYCY1HB681K∗ X 680p 50VCeramicAA
C915 VCKYPA1HF103Z+ X 0.01 50VCeramicAA
C916 VCKYCY1HB103K∗ X 0.01 50VCeramicAA
C917 VCEA0A1HW105M+X 150VElectrolyticAA
C918 VCKYCY1HB681K∗ X 680p 50VCeramicAA
C919 VCEA0A1HW105M+X 150VElectrolyticAA
C920 VCEA0A1HW105M+X 150VElectrolyticAA
C921 VCKYCY1HB681K∗ X 680p 50VCeramicAA
C922 VCKYCY1CF104Z∗ X 0.116VCeramicAA
C923 VCEA0A1CW107M+X 10016VElectrolyticAA
C926 VCEA0A1EW476M+X 4725VElectrolyticAA
C928 VCEA0A1HW105M+X 150VElectrolyticAA
C930 VCEA0A1HW475M+X 4.750VElectrolyticAA
C931 VCKYCY1HB183K∗ X 0.018 50VCeramicAA
C932 VCKYCY1HB183K∗ X 0.018 50VCeramicAA
C933 VCEA0A1HW475M+X 4.750VElectrolyticAA
C934 VCEA0A1EW476M+X 4725VElectrolyticAA
C935 VCEA0A1HW475M+X 4.750VElectrolyticAA
C936 VCEA0A1HW475M+X 4.750VElectrolyticAA
C937 VCKYCY1HB103K∗ X 0.01 50VCeramicAA
C953 VCKYCY1HB681K∗ X 680p 50VCeramicAA
C956 VCEA0A1CW477M+X 47016VElectrolyticAB
C1434 VCEA0A1EW476M+X 4725VElectrolyticAA
C1437 VCEA0A1EW476M+X 4725VElectrolyticAA
C2001 VCCCCY1HH101J∗ X 100p 50VCeramicAA
C2002 VCKYCY1HF103Z∗ X 0.01 50VCeramicAA
C2025 VCCCCY1HH101J∗ X 100p 50VCeramicAA
C2040 VCKYCY1CF104Z∗ X 0.116VCeramicAA
C2041 VCEA0A1HW105M+X 150VElectrolyticAA
C2043 VCCCCY1HH331J∗ X 330p 50VCeramicAA
C2044 VCCCCY1HH100D∗X 10p50VCeramicAA
C2046 VCEA0A1EW476M+X 4725VElectrolyticAA
C2060 VCKYCY1CF104Z∗ X 0.116VCeramicAA
C2061 VCCCCY1HH101J∗ X 100p 50VCeramicAA
C2062 VCEA0A1CW107M+X 10016VElectrolyticAA
C2063 VCKYCY1CF104Z∗ X 0.116VCeramicAA
C2064 VCKYCY1CF104Z∗ X 0.116VCeramicAA
C2201 VCKYCY1HB681K∗ X 680p 50VCeramicAA
C2202 VCCCCY1HH330J∗ X 33p50VCeramicAA
C2601 VCEA0A1EW476M+X 4725VElectrolyticAA
C2602 VCCCCY1HH101J∗ X 100p 50VCeramicAA
C3001 VCEA0A1HW475M+X 4.750VElectrolyticAA
C3002 VCKYCY1HB562K∗ X 5600p 50VCeramicAA
C3003 VCKYCY1EB123K∗ X 0.012 25VCeramicAA
C3004 VCEA0A1HW105M+X 150VElectrolyticAA
C3005 VCEA0A1HW475M+X 4.750VElectrolyticAA
C3006 VCEA0A1HW106M+X 1050VElectrolyticAA
C3007 VCEA0A1HW475M+X 4.750VElectrolyticAA
C3008 VCKYCY1CF104Z∗ X 0.116VCeramicAA
C3009 VCEA0A1CW477M+X 47016VElectrolyticAB
C3010 VCE9GA1HW475M+X 4.750VElect.(N,P)AB
C3011 VCEA0A1HW475M+X 4.750VElectrolyticAA
C3012 VCEA0A1HW475M+X 4.750VElectrolyticAA
C3013 VCKYCY1HB272K∗ X 2700p 50VCeramicAA
C3014 VCKYCY1CB473K∗ X 0.047 16VCeramicAA
C3015 VCEACA1HC335K+ X 3.350VElectrolyticAB
C3016 VCE9GA1HW475M+X 4.750VElect.(N,P)AB
C3017 VCEACA1CC106K+ X 1016VElectrolyticAB
C3018 VCEA0A1HW105M+X 150VElectrolyticAA
C3021 VCEA0A1HW475M+X 4.750VElectrolyticAA
C3022 VCEA0A1HW475M+X 4.750VElectrolyticAA
C3025 VCKYCY1CB473K∗ X 0.047 16VCeramicAA
C3027 VCKYCY1CB473K∗ X 0.047 16VCeramicAA
C3028 VCKYCY1HB682K∗ X 6800p 50VCeramicAA
RJ3VRS-CY1JF000J∗ X 01/16W Metal Oxide AA
RJ5VRS-CY1JF000J∗ X 01/16W Metal Oxide AA
RJ10 VRS-CY1JF000J∗ X 01/16W Metal Oxide AA
RJ16 VRS-CY1JF000J∗ X 01/16W Metal Oxide AA
RJ19 VRS-CY1JF000J∗ X 01/16W Metal Oxide AA
RJ20 VRS-CY1JF000J∗ X 01/16W Metal Oxide AA
RJ22 VRS-CY1JF000J∗ X 01/16W Metal Oxide AA
RJ23 VRS-CY1JF000J∗ X 01/16W Metal Oxide AA
RJ25 VRS-CY1JF000J∗ X 01/16W Metal Oxide AA
R54VRS-CY1JF101J∗ X 100 1/16W Metal Oxide AA
R55VRS-CY1JF101J∗ X 100 1/16W Metal Oxide AA
R56VRD-RA2BE823J∗ X 82k 1/8WCarbonAA
R57VRS-CY1JF473J∗ X 47k 1/16W Metal Oxide AA
R201 VRS-CY1JF151J∗ X 150 1/16W Metal Oxide AA
R202 VRS-CY1JF122J∗ X 1.2k 1/16W Metal Oxide AA
R203 VRS-CY1JF682J∗ X 6.8k 1/16W Metal Oxide AA
R204 VRS-CY1JF270J∗ X 271/16W Metal Oxide AA
R205 VRS-CY1JF331J∗ X 330 1/16W Metal Oxide AA
R206 VRD-RA2BE101J∗ X 100 1/8WCarbonAA
R211 VRS-CY1JF221J∗ X 220 1/16W Metal Oxide AA
R212 VRS-CY1JF221J∗ X 220 1/16W Metal Oxide AA
R225 VRS-CY1JF101J∗ X 100 1/16W Metal Oxide AA
R226 VRS-CY1JF101J∗ X 100 1/16W Metal Oxide AA
R227 VRS-CY1JF273J∗ X 27k 1/16W Metal Oxide AA
R232 VRS-CY1JF471J∗ X 470 1/16W Metal Oxide AA
R234 VRD-RA2BE271J∗ X 270 1/8WCarbonAA
R236 VRS-CY1JF332J∗ X 3.3k 1/16W Metal Oxide AA
R301 VRS-CY1JF222J∗ X 2.2k 1/16W Metal Oxide AA
R305 VRS-CY1JF000J∗ X 01/16W Metal Oxide AA
R306 VRS-CY1JF102J∗ X 1k1/16W Metal Oxide AA
R307 VRS-CY1JF101J∗ X 100 1/16W Metal Oxide AA
R308VRS-CY1JF000J∗X01/16
R361VRS-RA2BE224J∗X220k1/8WCarbonAA
R362VRS-CY1JF222J∗X1.8k1/16WMetal OxideAA
R363VRS-CY1JF222J∗X1.8k1/16WMetal OxideAA
R364VRD-RA2BE681J∗X1.5k1/8WCarbonAA
R365VRS-CY1JF681J∗X1.5k1/16WMetal OxideAA
å R367 VRN-RL3DB1R2J+ X 1.2 2WMetal FilmAB
R368VRD-RA2BE222J∗X2.2k1/8WCarbonAA
R369 VRD-RA2BE822J∗ X 8.2k 1/8WCarbonAA
R371 VRS-CY1JF102J∗ X 1k1/16W Metal Oxide AA
R372 VRS-CY1JF223J∗ X 22k 1/16W Metal Oxide AA
R403 VRS-CY1JF000J∗ X 01/16W Metal Oxide AA
R404 VRS-CY1JF683J∗ X 68k 1/16W Metal Oxide AA
R406 VRS-CY1JF473J∗ X 47k 1/16W Metal Oxide AA
R407 VRS-CY1JF102J∗ X 1k1/16W Metal Oxide AA
R408 VRS-CY1JF683J∗ X 68k 1/16W Metal Oxide AA
R410 VRS-CY1JF473J∗ X 47k 1/16W Metal Oxide AA
R411 VRS-CY1JF102J∗ X 1k1/16W Metal Oxide AA
R412 VRS-CY1JF101J∗ X 100 1/16W Metal Oxide AA
R413 VRS-CY1JF101J∗ X 100 1/16W Metal Oxide AA
R414 VRS-CY1JF000J∗ X 01/16W Metal Oxide AA
R415 VRS-CY1JF000J∗ X 01/16W Metal Oxide AA
R422 VRS-CY1JF000J∗ X 01/16W Metal Oxide AA
R430 VRS-CY1JF391J∗ X 390 1/16W Metal Oxide AA
R431 VRS-CY1JF331J∗ X 330 1/16W Metal Oxide AA
R432 VRS-CY1JF102J∗ X 1k1/16W Metal Oxide AA
R437 VRS-CY1JF101J∗ X 100 1/16W Metal Oxide AA
R438 VRS-CY1JF101J∗ X 100 1/16W Metal Oxide AA
R439 VRS-CY1JF104J∗ X 100k 1/16W Metal Oxide AA
R440 VRS-CY1JF000J∗ X 01/16W Metal Oxide AA
R441 VRS-CY1JF472J∗ X 4.7k 1/16W Metal Oxide AA
R442 VRS-CY1JF101J∗ X 100 1/16W Metal Oxide AA
R444 VRS-CY1JF332J∗ X 3.3k 1/16W Metal Oxide AA
R445 VRS-CY1JF332J∗ X 3.3k 1/16W Metal Oxide AA
R446 VRS-CY1JF332J∗ X 3.3k 1/16W Metal Oxide AA
R447 VRS-CY1JF101J∗ X 100 1/16W Metal Oxide AA
R448 VRS-CY1JF101J∗ X 100 1/16W Metal Oxide AA
RESISTORS
WMetal OxideAA
R449 VRS-CY1JF101J∗ X 100 1/16W Metal Oxide AA
R450 VRS-CY1JF101J∗ X 100 1/16W Metal Oxide AA
å R451 VRS-RG3AB103J+ X 10k 1WMetal Oxide AB
R452 VRD-RM2HD823J∗ X 82k 1/2WCarbonAA
R453 VRD-RM2HD823J∗ X 82k 1/2WCarbonAA
R454 VRS-CY1JF471J∗ X 470 1/16W Metal Oxide AA
R455 VRD-RM2HD473J∗ X 47k 1/2WCarbonAA
R456 VRS-CY1JF103J∗ X 10k 1/16W Metal Oxide AA
R460 VRS-CY1JF471J∗ X 470 1/16W Metal Oxide AA
R461 VRS-CY1JF562J∗ X 5.6k 1/16W Metal Oxide AA
R462 VRS-CY1JF223J∗ X 22k 1/16W Metal Oxide AA
R463 VRD-RA2EE680J∗ X 681/4WCarbonAA
R464 VRS-CY1JF683J∗ X 68k 1/16W Metal Oxide AA
R467 VRS-CY1JF123J∗ X 12k 1/16W Metal Oxide AA
R471 VRS-CY1JF333J∗ X 33k 1/16W Metal Oxide AA
R472 VRS-CY1JF273J∗ X 27k 1/16W Metal Oxide AA
R473 VRS-CY1JF471J∗ X 470 1/16W Metal Oxide AA
R474 VRS-CY1JF681J∗ X 680 1/16W Metal Oxide AA
R475 VRS-CY1JF102J∗ X 1k1/16W Metal Oxide AA
R476 VRS-CY1JF393J∗ X 39k 1/16W Metal Oxide AA
R477 VRS-CY1JF182J∗ X 1.8k 1/16W Metal Oxide AA
R478 VRS-CY1JF151J∗ X 150 1/16W Metal Oxide AA
R479 VRS-CY1JF473J∗ X 47k 1/16W Metal Oxide AA
R480 VRS-CY1JF223J∗ X 22k 1/16W Metal Oxide AA
R481 VRS-CY1JF152J∗ X 1.5k 1/16W Metal Oxide AA
R482 VRS-CY1JF100J∗ X 101/16W Metal Oxide AA
R483 VRS-CY1JF101J∗ X 100 1/16W Metal Oxide AA
å R501 VRN-RL3ABR47J+ X 0.47 1WMetal FilmAB
R502 VRN-RA2BK822F∗ X 8.2k 1/8WMetal FilmAA
R503 VRS-CY1JF105J∗ X 1M 1/16W Metal Oxide AA
R504 VRS-CY1JF154J∗ X 150k 1/16W Metal Oxide AA
R505 VRS-CY1JF101J∗ X 100 1/16W Metal Oxide AA
R510 VRN-RA2BK103F∗ X 10k 1/8WMetal FilmAA
R511 VRN-RA2BK222F∗ X 2.2k 1/8WMetal FilmAA
R512 VRN-RA2BK272F∗ X 2.7k 1/8WMetal FilmAA
R513 VRD-RM2HD1R0J∗ X 11/2WCarbonAA
R517 VRS-CY1JF104J∗ X 100k 1/16W Metal Oxide AA
R518 VRS-CY1JF102J∗ X 1k1/16W Metal Oxide AA
R521 VRS-CY1JF101J∗ X 100 1/16W Metal Oxide AA
å R523 VRN-RL3DB1R0J+ X 12WMetal FilmAB
å R524 VRS-RG3AB391J+ X 390 1WMetal Oxide AB
R601 VRS-CY1JF101J∗ X 100 1/16W Metal Oxide AA
R603 VRD-RA2BE472J∗ X 4.7k 1/8WCarbonAA
å R604 VRS-KA3NG562JX 5.6k 7.0WMetal Oxide AB
R605 VRD-RM2HD331J∗ X 330 1/2WCarbonAA
R606 VRD-RM2HD331J∗ X 330 1/2WCarbonAA
å R609 VRS-RG3AB562J+ X 5.6k 1WMetal Oxide AB
R610 VRD-RM2HD220J∗ X 221/2WCarbonAA
R612 VRS-CY1JF154J∗ X 150k 1/16W Metal Oxide AA
R613 VRS-CY1JF101J∗ X 100k 1/16W Metal Oxide AA
R614 VRS-CY1JF562J∗ X 5.6k 1/16W Metal Oxide AA
å R615 VRS-KA3NG3R3K X 3.3 7.0WMetal Oxide AB
R618 VRS-CY1JF101J∗ X 100 1/16W Metal Oxide AA
å R621 VRN-RL3AB3R3J+ X 3.3 1WMetal FilmAB
å R622 VRN-RL3ABR47J+ X 0.47 1WMetal FilmAB
å R623 VRN-RL3AB4R7J+ X 4.7 1WMetal FilmAB
å R624 VRS-RG3DB332J+ X 3.3k 2WMetal Oxide AB
R625 VRD-RA2BE102J∗ X 1k1/8WCarbonAA
å R627 VRN-RL3ABR47J+ X 0.47 1WMetal FilmAB
å R628 VRN-RL3ABR47J+ X 0.47 1WMetal FilmAB
'åR651 VRS-RG2HC270J+ X 271/2WMetal Oxide AB
'åR652 VRD-RA2EE103G∗ X 10k 1/4W2% CarbonAA
'å R653 VRD-RA2EE562G∗ X 5.6k 1/4W2% CarbonAA
å R658 VRS-RG3LB333J+ X 33k 3.0WMetal Oxide AB
R663 VRS-CY1JF102J∗ X 1k1/16W Metal Oxide AA
R670 VRS-CY1JF000J∗ X 01/16W Metal Oxide AA
R684 VRD-RA2BE472J∗ X 4.7k 1/8WCarbonAA
R685 VRD-RA2BE822J∗ X 8.2k 1/8WCarbonAA
R686 VRD-RA2EE332J∗ X 3.3k 1/4WCarbonAA
R687 VRD-RA2BE103J∗ X 10k 1/8WCarbonAA
å R688 VRN-RL3DB3R3J+ X 3.3 2WMetal FilmAB
R689 VRD-RM2HD824J∗ X 820k 1/2WCarbonAA
å R690 VRS-RG3LB471J+ X 470 3.0WMetal Oxide AB
R691 VRS-CY1JF394J∗ X 390k 1/16W Metal Oxide AA
R692 VRS-CY1JF223J∗ X 22k 1/16W Metal Oxide AA
R693 VRS-CY1JF683J∗ X 68k 1/16W Metal Oxide AA
R694 VRS-CY1JF102J∗ X 1k1/16W Metal Oxide AA
R695 VRS-CY1JF683J∗ X 68k 1/16W Metal Oxide AA
R696 VRS-CY1JF000J∗ X 01/16W Metal Oxide AA
å R701 RR-DZ0049CEZZ∗ X 3.9M 1/2WSolidAB
å R703 VRW-KQ4AC1R2K X 1.2 10WCementAB
å R705 VRN-RL3DBR18J+ X 0.18 2WMetal FilmAB
å R706 VRN-RL3DBR18J+ X 0.18 2WMetal FilmAB
R707 VRD-RM2HD270J∗ X 271/2WCarbonAA
R708 VRS-CY1JF102J∗ X 1k1/16W Metal Oxide AA
R709 VRS-CY1JF000J∗ X 01/16W Metal Oxide AA
å R710 VRS-RG2HC103J+ X 10k 1/2WMetal Oxide AB
R711 VRS-CY1JF334J∗ X 330k 1/16W Metal Oxide AA
R712 VRD-RM2HD100J∗ X 101/2WCarbonAA
å R713 VRS-RG2HC122J+ X 1.2k 1/2WMetal Oxide AB
R715 VRD-RM2HD5R6J∗ X 5.6 1/2WCarbonAA
R716 VRD-RM2HD100J∗ X 101/2WCarbonAA
R720 VRD-RA2BE473J∗ X 47k 1/8WCarbonAA
R724 VRS-CY1JF000J∗ X 01/16W Metal Oxide AA
R725 VRD-RM2HD221J∗ X 220 1/2WCarbonAA
R734 VRD-RM2HD124J∗ X 120k 1/2WCarbonAA
å R737 VRN-RL3LBR82J+ X 0.82 3.0WMetal FilmAB
R742 VRD-RA2BE222J∗ X 2.2k 1/8WCarbonAA
R743 VRD-RM2HD470J∗ X 471/2WCarbonAA
R751 VRD-RA2BE473J∗ X 47k 1/8WCarbonAA
R752 VRD-RA2BE392J∗ X 3.9k 1/8WCarbonAA
R753 VRS-CY1JF222J∗ X 2.2k 1/16W Metal Oxide AA
R754 VRS-CY1JF222J∗ X 2.2k 1/16W Metal Oxide AA
R755 VRS-CY1JF473J∗ X 47k 1/16W Metal Oxide AA
R756 VRD-RA2BE152J∗ X 1.5k 1/8WCarbonAA
å R757 VRN-RL3DB4R7J+ X 4.7 2WMetal FilmAB
R759 VRS-CY1JF103J∗ X 10k 1/16W Metal Oxide AA
R761 VRS-CY1JF332J∗ X 3.3k 1/16W Metal Oxide AA
R762 VRD-RA2BE103J∗ X 10k 1/8WCarbonAA
R764 VRD-RM2HD562J∗ X 5.6k 1/2WCarbonAA
R767 VRD-RM2HD151J∗ X 150 1/2WCarbonAA
R768 VRD-RA2BE473J∗ X 47k 1/8WCarbonAA
R770 VRS-CY1JF102J∗ X 1k1/16W Metal Oxide AA
R771 VRS-CY1JF103J∗ X 10k 1/16W Metal Oxide AA
R772 VRS-CY1JF103J∗ X 10k 1/16W Metal Oxide AA
R773 VRD-RM2HD823J∗ X 82k 1/2WCarbonAA
R774 VRD-RA2BE272J∗ X 2.7k 1/8WCarbonAA
R775 VRS-CY1JF332J∗ X 3.3k 1/16W Metal Oxide AA
R776 VRS-CY1JF332J∗ X 3.3k 1/16W Metal Oxide AA
R801 VRS-CY1JF333J∗ X 33k 1/16W Metal Oxide AA
R802 VRS-CY1JF471J∗ X 470 1/16W Metal Oxide AA
R803 VRS-CY1JF000J∗ X 01/16W Metal Oxide AA
R805 VRS-CY1JF682J∗ X 6.8k 1/16W Metal Oxide AA
R806 VRS-CY1JF681J∗ X 680 1/16W Metal Oxide AA
R807 VRS-CY1JF681J∗ X 680 1/16W Metal Oxide AA
R808 VRS-CY1JF681J∗ X 680 1/16W Metal Oxide AA
R810 VRS-CY1JF472J∗ X 4.7k 1/16W Metal Oxide AA
R903 VRS-CY1JF102J∗ X 1k1/16W Metal Oxide AA
R904 VRS-CY1JF683J∗ X 68k 1/16W Metal Oxide AA
R905 VRS-CY1JF223J∗ X 22k 1/16W Metal Oxide AA
R906 VRD-RA2BE332J∗ X 3.3k 1/8WCarbonAA
R907 VRS-CY1JF152J∗ X 1.5k 1/16W Metal Oxide AA
R908 VRS-CY1JF102J∗ X 1k1/16W Metal Oxide AA
R910 VRD-RA2BE102J∗ X 1k1/8WCarbonAA
R911 VRS-CY1JF683J∗ X 68k 1/16W Metal Oxide AA
R912 VRS-CY1JF223J∗ X 22k 1/16W Metal Oxide AA
R913 VRS-CY1JF332J∗ X 3.3k 1/16W Metal Oxide AA
R914 VRS-CY1JF152J∗ X 1.5k 1/16W Metal Oxide AA
R915 VRS-CY1JF102J∗ X 1k1/16W Metal Oxide AA
R916 VRS-CY1JF683J∗ X 68k 1/16W Metal Oxide AA
R917 VRS-CY1JF332J∗ X 3.3k 1/16W Metal Oxide AA
R918 VRS-CY1JF332J∗ X 3.3k 1/16W Metal Oxide AA
R922 VRS-CY1JF102J∗ X 1k1/16W Metal Oxide AA
R923 VRS-CY1JF102J∗ X 1k1/16W Metal Oxide AA
R924 VRS-CY1JF750J∗ X 751/16W Metal Oxide AA
R925 VRS-CY1JF750J∗ X 751/16W Metal Oxide AA
R926 VRS-CY1JF680J∗ X 681/16W Metal Oxide AA
R927 VRS-CY1JF750J∗ X 751/16W Metal Oxide AA
R929 VRS-CY1JF473J∗ X 47k 1/16W Metal Oxide AA
R930 VRS-CY1JF473J∗ X 47k 1/16W Metal Oxide AA
R931 VRS-CY1JF750J∗ X 751/16W Metal Oxide AA
R932 VRS-CY1JF473J∗ X 47k 1/16W Metal Oxide AA
R933 VRS-CY1JF473J∗ X 47k 1/16W Metal Oxide AA
R934 VRS-CY1JF103J∗ X 10k 1/16W Metal Oxide AA
R935 VRS-CY1JF101J∗ X 100 1/16W Metal Oxide AA
R936 VRS-CY1JF223J∗ X 22k 1/16W Metal Oxide AA
R937 VRS-CY1JF101J∗ X 100 1/16W Metal Oxide AA
R938 VRS-CY1JF223J∗ X 22k 1/16W Metal Oxide AA
R939 VRS-CY1JF333J∗ X 33k 1/16W Metal Oxide AA
R940 VRS-CY1JF8R2J∗ X 8.2 1/16W Metal Oxide AA
R941 VRS-CY1JF101J∗ X 100 1/16W Metal Oxide AA
R942 VRS-CY1JF223J∗ X 22k 1/16W Metal Oxide AA
R943 VRS-CY1JF101J∗ X 100 1/16W Metal Oxide AA
R944 VRS-CY1JF223J∗ X 22k 1/16W Metal Oxide AA
R945 VRS-CY1JF101J∗ X 100 1/16W Metal Oxide AA
R946 VRS-CY1JF103J∗ X 10k 1/16W Metal Oxide AA
R947 VRS-CY1JF223J∗ X 22k 1/16W Metal Oxide AA
R948 VRS-CY1JF101J∗ X 100 1/16W Metal Oxide AA
R949 VRS-CY1JF223J∗ X 22k 1/16W Metal Oxide AA
R950 VRS-CY1JF750J∗ X 751/16W Metal Oxide AA
R951 VRD-RA2BE680J∗ X 681/8WCarbonAA
R952 VRS-CY1JF333J∗ X 33k 1/16W Metal Oxide AA
R954 VRS-CY1JF221J∗ X 220 1/16W Metal Oxide AA
R955 VRS-CY1JF221J∗ X 220 1/16W Metal Oxide AA
R957 VRS-CY1JF101J∗ X 100 1/16W Metal Oxide AA
R958 VRS-CY1JF101J∗ X 100 1/16W Metal Oxide AA
R959 VRS-CY1JF103J∗ X 10k 1/16W Metal Oxide AA
R960 VRS-CY1JF101J∗ X 100 1/16W Metal Oxide AA
R961 VRS-CY1JF102J∗ X 1k1/16W Metal Oxide AA
R962 VRS-CY1JF332F∗ X 3.3k 1/16W Metal Oxide AA
R963 VRD-RA2BE331J∗ X 330 1/8WCarbonAA
R964 VRS-CY1JF152J∗ X 1.5k 1/16W Metal Oxide AA
R967 VRS-CY1JF682J∗ X 6.8k 1/16W Metal Oxide AA
R968 VRS-CY1JF102J∗ X 1k1/16W Metal Oxide AA
R969 VRS-CY1JF472F∗ X 4.7k 1/16W Metal Oxide AA
R970 VRD-RA2BE6R8J∗ X 6.8 1/8WCarbonAA
R971 VRS-CY1JF101J∗ X 100 1/16W Metal Oxide AA
R972 VRS-CY1JF101J∗ X 100 1/16W Metal Oxide AA
R973 VRS-CY1JF000J∗ X 01/16W Metal Oxide AA
R974 VRS-CY1JF103J∗ X 10k 1/16W Metal Oxide AA
R975 VRS-CY1JF333J∗ X 33k 1/16W Metal Oxide AA
R982 VRS-CY1JF750J∗ X 751/16W Metal Oxide AA
R983 VRS-CY1JF473J∗ X 47k 1/16W Metal Oxide AA
R984 VRS-CY1JF473J∗ X 47k 1/16W Metal Oxide AA
å R1420 VRN-RL3LB2R7J+ X 2.7 3.0WMetal FilmAB
R2001 VRS-CY1JF102J∗ X 1k1/16W Metal Oxide AA
R2004 VRS-CY1JF101J∗ X 100 1/16W Metal Oxide AA
R2008 VRS-CY1JF102J∗ X 1k1/16W Metal Oxide AA
R2010 VRS-CY1JF102J∗ X 1k1/16W Metal Oxide AA
R2013 VRS-CY1JF682J∗ X 6.8k 1/16W Metal Oxide AA
R2021 VRS-CY1JF334J∗ X 330k 1/16W Metal Oxide AA
R2024 VRS-CY1JF472J∗ X 4.7k 1/16W Metal Oxide AA
R2025 VRS-CY1JF472J∗ X 4.7k 1/16W Metal Oxide AA
R2026 VRS-CY1JF472J∗ X 4.7k 1/16W Metal Oxide AA
R2027 VRS-CY1JF102J∗ X 1k1/16W Metal Oxide AA
R2028 VRD-RA2BE102J∗ X 1k1/8WCarbonAA
R2031 VRS-CY1JF222J∗ X 2.2k 1/16W Metal Oxide AA
R2033 VRS-CY1JF334J∗ X 330k 1/16W Metal Oxide AA
R2040 VRS-CY1JF102J∗ X 1k1/16W Metal Oxide AA
R2041 VRS-CY1JF333J∗ X 33k 1/16W Metal Oxide AA
R2042 VRS-CY1JF101J∗ X 100 1/16W Metal Oxide AA
R2043 VRS-CY1JF333J∗ X 33k 1/16W Metal Oxide AA
R2044 VRS-CY1JF153J∗ X 15k 1/16W Metal Oxide AA
R2046 VRS-CY1JF101J∗ X 100 1/16W Metal Oxide AA
R2047 VRS-CY1JF221J∗ X 220 1/16W Metal Oxide AA
R2048 VRS-CY1JF562J∗ X 5.6k 1/16W Metal Oxide AA
R2051 VRS-CY1JF102J∗ X 1k1/16W Metal Oxide AA
R2060 VRS-CY1JF221J∗ X 220 1/16W Metal Oxide AA
R2061 VRS-CY1JF562J∗ X 5.6k 1/16W Metal Oxide AA
R2062 VRS-CY1JF223J∗ X 22K 1/16W Metal Oxide AA
R2063 VRS-CY1JF222J∗ X 2.2k 1/16W Metal Oxide AA
R2064 VRS-CY1JF332J∗ X 3.3k 1/16W Metal Oxide AA
R2073 VRS-CY1JF000J∗ X 01/16W Metal Oxide AA
R2084 VRS-CY1JF103J∗ X 10k 1/16W Metal Oxide AA
R2086 VRS-CY1JF101J∗ X 100 1/16W Metal Oxide AA
R2090 VRS-CY1JF101J∗ X 100 1/16W Metal Oxide AA
R2092 VRS-CY1JF101J∗ X 100 1/16W Metal Oxide AA
R2101 VRS-CY1JF101J∗ X 100 1/16W Metal Oxide AA
R2102 VRS-CY1JF101J∗ X 100 1/16W Metal Oxide AA
R2201 VRS-CY1JF222J∗ X 2.2k 1/16W Metal Oxide AA
R2202 VRS-CY1JF103J∗ X 10k 1/16W Metal Oxide AA
R2203 VRS-CY1JF473J∗ X 47k 1/16W Metal Oxide AA
R2211 VRS-CY1JF222J∗ X 2.2k 1/16W Metal Oxide AA
R2212 VRS-CY1JF682J∗ X 6.8k 1/16W Metal Oxide AA
R2213 VRS-CY1JF333J∗ X 33k 1/16W Metal Oxide AA
R2401 VRD-RA2BE101J∗ X 100 1/8WCarbonAA
R2402 VRD-RA2BE101J∗ X 100 1/8WCarbonAA
R2403 VRD-RA2BE101J∗ X 100 1/8WCarbonAA
R2404 VRD-RA2BE101J∗ X 100 1/8WCarbonAA
R2501 VRS-CY1JF183J∗ X 18k 1/16W Metal Oxide AA
R2502 VRS-CY1JF183J∗ X 18k 1/16W Metal Oxide AA
R2503 VRS-CY1JF103J∗ X 10k 1/16W Metal Oxide AA
R2504 VRS-CY1JF103J∗ X 10k 1/16W Metal Oxide AA
R2505 VRD-RA2BE822J∗ X 8.2k 1/8WCarbonAA
R2506 VRD-RA2BE822J∗ X 8.2k 1/8WCarbonAA
R2507 VRD-RA2BE183J∗ X 18k 1/8WCarbonAA
R2508 VRD-RA2BE183J∗ X 18k 1/8WCarbonAA
R2509 VRS-CY1JF000J∗ X 01/16W Metal Oxide AA
R2601 VRD-RA2BE100J∗ X 101/8WCarbonAA
R2603 VRS-CY1JF000J∗ X 01/16W Metal Oxide AA
R2605 VRS-CY1JF000J∗ X 01/16W Metal Oxide AA
R2606 VRS-CY1JF000J∗ X 01/16W Metal Oxide AA
R3001 VRS-CY1JF221J∗ X 220 1/16W Metal Oxide AA
R3002 VRS-CY1JF221J∗ X 220 1/16W Metal Oxide AA
R3003 VRS-CY1JF105J∗ X 1M 1/16W Metal Oxide AA
R3004 VRS-CY1JF104J∗ X 100k 1/16W Metal Oxide AA
R3005 VRS-CY1JF623J∗ X 62k 1/16W Metal Oxide AA
R3007 VRS-CY1JF332J∗ X 3.3k 1/16W Metal Oxide AA
R3008 VRS-CY1JF302J∗ X 3k1/16W Metal Oxide AA
R3010 VRS-CY1JF392J∗ X 3.9k 1/16W Metal Oxide AA
R3017 VRS-CY1JF102J∗ X 1k1/16W Metal Oxide AA
R3018 VRS-CY1JF102J∗ X 1k1/16W Metal Oxide AA
R3019 VRS-CY1JF101J∗ X 100 1/16W Metal Oxide AA
R3020 VRS-CY1JF101J∗ X 100 1/16W Metal Oxide AA
R3021 VRS-CY1JF101J∗ X 100 1/16W Metal Oxide AA
R3023 VRS-CY1JF101J∗ X 100 1/16W Metal Oxide AA
R3024 VRD-RA2BE102J∗ X 1k1/8WCarbonAA
S2501 QSW-KA003WJZZ+ X Switch, POWERAB
S2502 QSW-KA003WJZZ+ X Switch, MENUAB
S2503 QSW-KA003WJZZ+ X Switch, VOL.-DOWNAB
S2504 QSW-KA003WJZZ+ X Switch, VOL.-UPAB
S2505 QSW-KA003WJZZ+ X Switch, CH-DOWNAB
S2506 QSW-KA003WJZZ+ X Switch, CH-UPAB
MISCELLANEOUS PARTS
å
ACC701
QACCDA012WJPZ X AC CordAE
CF2040
RCRM-0003CEZZ+ X Ceramic VibratorAC
FB601 RBLN-0047CEZZ∗ X Ferrite BeadAB
FB706 RBLN-0037CEZZ∗ X Ferrite BeadAA
FB2001
å F701QFS-B4023CEZZX Fuse, 4A/125VAB
RBLN-0037CEZZ∗ X Ferrite BeadAA
FH701 QFSHD1013CEZZ+ X Fuse HolderAA
FH702 QFSHD1014CEZZ+ X Fuse HolderAA
J904QJAKGA031WJZZ X Front AV In JackAC
J921QSOCD0430CEZZ X S-Video terminalAC
J1401 QTANJ1101SEZZX AV In/Out TerminalAF
P361 QPLGN0461CEZZA X Plug, 4pin(S1-4)AB
P401 QPLGN0861CEZZA X Plug, 8pin(CJ)AB
P605 QPLGN0160FJZZ X Plug, 5pin(K1-5)AB
P621 QPLGN0761CEZZA X Plug, 7pin(N)AB
SWITCHES
P651 QPLGN0361CEZZA X Plug, 3pin(TP651-3)AB
P702 QPLGN0269GEZZ X Plug, 2pin(P1-2)AB
P703 QPLGN0260CEZZ X Plug, 2pin(M1-2)AB
P2401 QPLGN0661CEZZA X Plug, 6pinAB
RMC2601
RRMCU0222CEZZ X Remote ReceiverAD
RY701 RRLYJ0081CEZZ X RelayAD
TP701 QLUGP0102PEZZ X LugAA
RDA361
PRDAR0258PEFW X Heat Sink for IC361AC
RDA501
PRDARA039WJFW X Heat Sink for IC501AD
RDA601
PRDARA041WJFW X Heat Sink for Q602AD
RDA671
PRDARA057WJFW X Heat Sink for Q673AC
RDA701
PRDAR0279PEFW X Heat Sink for Q701AB
RDA750
PRDAR5072CEFW X Heat Sink for IC751AB
RDA1403
PRDAR5072CEFW X Heat Sink for IC1403AB
PWB-B: DUNTKA527WEV6
CRT UNIT
å IC850 VHiTDA6103Q-1X TDA6103Q/N3AG
Q850 VS2SA1266-Y-1+X 2SA1266AB
Q851 VS2SC3198-G-1+ X 2SC3198AB
Q1504 VS2SC3198-G-1+ X 2SC3198AB
Q1505 VS2SA1266-Y-1+X 2SA1266AB
Q1506 VS2SA1964E/-1X 2SA1964EAC
Q1507 VS2SC5248E/-1X 2SC5248EAC
C850 VCFYSB2EB823J X 0.082 250VAB
C851 RC-KZ018JCEZZX 0.01
C852 VCEA0A1CW107M+X 10016VElectrolyticAA
C853 VCFYFA1HA224J+ X 0.22 50VMylarAB
C854 VCEA0A1CW227M+X 22016VElectrolyticAB
C855 VCEA0A2EW106M+X 10250V ElectrolyticAB
C856 VCEA0A1HW226M+X 2250VElectrolyticAA
C1501 VCEA0A1CW476M+X 4716VElectrolyticAA
C1506 VCKYPA1HF103Z+ X 0.01 50VCeramicAA
C1508 VCKYPA2HB472K+ X 4700p 500V CeramicAB
C1509 VCKYPA1HB472K+ X 4700p 50VCeramicAA
C1510 VCKYPA1HF103Z+ X 0.01 50VCeramicAA
C1511 VCKYPA1HF103Z+ X 0.01 50VCeramicAA
C1515 VCEA0A1HW476M+X 4750VElectrolyticAB
C1516 VCEA0A1HW476M+X 4750VElectrolyticAB
C1517 VCEA0A2AW106M+X 10100V ElectrolyticAB
C1518 VCCSPA2HL560K+ X 56p500V CeramicAB
C1519 VCEA0A2CW106M+X 10160V ElectrolyticAB
å R850 VRS-SV2HC152JX 1.5k 1/2WMetal Oxide AA
å R851 VRS-SV2HC152JX 1.5k 1/2WMetal Oxide AA
å R852 VRS-SV2HC152JX 1.5k 1/2WMetal Oxide AA
å R853 VRS-SV2HC272JX 2.7k 1/2WMetal Oxide AA
å R854 VRS-SV2HC272JX 2.7k 1/2WMetal Oxide AA
å R855 VRS-SV2HC272JX 2.7k 1/2WMetal Oxide AA
R856 VRD-RM2HD104J∗ X 100k 1/2WCarbonAA
R857 VRD-RM2HD104J∗ X 100k 1/2WCarbonAA
R858 VRD-RM2HD104J∗ X 100k 1/2WCarbonAA
R861 VRD-RM2HD104J∗ X 100k 1/2WCarbonAA
R862 VRC-MA2HG152K∗ X 1.5k 1/2WSolidAB
R863 VRC-MA2HG152K∗ X 1.5k 1/2WSolidAB
R864 VRC-MA2HG152K∗ X 1.5k 1/2WSolidAB
å R867 VRS-SV2HC392JX 3.9k 1/2WMetal Oxide AA
å R868 VRS-SV2HC682JX 6.8k 1/2WMetal Oxide AA
R869 VRD-RA2BE103J∗ X 10k 1/8WCarbonAA
R870 VRD-RA2BE223J∗ X 22k 1/8WCarbonAA
R871 VRD-RA2BE472J∗ X 4.7k 1/8WCarbonAA
R872 VRD-RA2EE680J∗ X 681/4WCarbonAA
R873 VRD-RM2HD224J∗ X 220k 1/2WCarbonAA
R874 VRD-RM2HD104J∗ X 100k 1/2WCarbonAA
R875 VRD-RM2HD104J∗ X 100k 1/2WCarbonAA
R876 VRD-RM2HD104J∗ X 100k 1/2WCarbonAA
R877 VRD-RA2BE103J∗ X 10k 1/8WCarbonAA
å R878 VRS-SV2HC120JX 121/2WMetal Oxide AA
R1511 VRD-RA2BE101J∗ X 100 1/8WCarbonAA
å R1513 VRS-VV3DB561JX 560 2WMetal Oxide AB
R1514 VRD-RA2BE100J∗ X 101/8WCarbonAA
R1515 VRD-RA2BE820J∗ X 821/8WCarbonAA
R1516 VRD-RA2BE820J∗ X 821/8WCarbonAA
R1517 VRD-RA2BE122J∗ X 1.2k 1/8WCarbonAA
R1518 VRD-RA2BE683J∗ X 68k 1/8WCarbonAA
R1519 VRD-RA2BE123J∗ X 12k 1/8WCarbonAA
R1520 VRD-RA2BE683J∗ X 68k 1/8WCarbonAA
R1521 VRD-RA2BE122J∗ X 1.2k 1/8WCarbonAA
R1525 VRD-RA2EE560J∗ X 561/4WCarbonAA
R1526 VRD-RA2EE560J∗ X 561/4WCarbonAA
R1527 VRD-RM2HD1R5J∗ X 1.5 1/2WCarbonAA
R1528 VRD-RM2HD1R5J∗ X 1.5 1/2WCarbonAA
å R1529 VRS-VV3DB221JX 220 2WMetal Oxide AB
R1530 VRD-RA2BE122J∗ X 1.2k 1/8WCarbonAA
FB1501RBLN-0020CEZZ+ X Ferrite BeadAB
P854 QPLGN0741CEZZ X Plug, 7pin(N)AB
P860 QPLGN0841CEZZ X Plug, 8pin(CJ)AB
å P861 QPLGN0241CEZZ X Plug, 2pin(PU1-2)AA
SC850 QSOCV1011CEZZ X CRT SocketAC
RDA850
RDA1506
RDA1507
MISCELLANEOUS PARTS
PRDAR0248PEFW X Heat Sink for IC850AB
PRDAR5072CEFW X Heat Sink for Q1506AB
PRDAR5072CEFW X Heat Sink for Q1507AB
PWB-C: DUNTKA573WEV0
3-LINE Y/C UNIT
IC1401 VHiTC90A53F-1∗X TC90A53FAP
Q1403 VS2SB709AR/-1∗ X 2SB709ARAA
Q1406 VS2SB709AR/-1∗ X 2SB709ARAA
Q1408 VS2SB709AR/-1∗ X 2SB709ARAA
Q1401 VS2SD601AR/-1∗ X 2SD601ARAA
Q1402 VS2SD601AR/-1∗ X 2SD601ARAA
Q1404 VS2SD601AR/-1∗ X 2SD601ARAA
Q1407 VS2SD601AR/-1∗ X 2SD601ARAA
L1401 VP-XF100K0000∗ X Peaking 10µHAA
L1402 VP-XF100K0000∗ X Peaking 10µHAA
L1406 VP-XF220K0000∗ X Peaking 22µHAA
L1407 VP-XF220K0000∗ X Peaking 22µHAA
L1408 VP-XF100K0000∗ X Peaking 10µHAA
L1410 VP-XF100K0000∗ X Peaking 10µHAA
L1414 VP-XF330K0000∗ X Peaking 33µHAA
L1417 VP-XF220K0000∗ X Peaking 22µHAA
C1412 VCEA0A1HW106M+X 1050VElectrolyticAA
INTEGRATED CIRCUITS
TRANSISTORS
COILS
CAPACITORS
C1413 VCKYCY1HF103Z∗ X 0.01 50VCeramicAA
C1414 VCCCCY1HH3R0C∗X 3.0p50VCeramicAA
C1415 VCE9GA1CW106M+X 1016VElect.(N,P)AB
C1416 VCEA0A1CW477M+X 47016VElectrolyticAB
C1417 VCKYCY1CF104Z∗ X 0.116VCeramicAA
C1420 VCCCCY1HH270J∗ X 27p50VCeramicAA
C1421 VCCCCY1HH120J∗ X 12p50VCeramicAA
C1422 VCCCCY1HH120J∗ X 12p50VCeramicAA
C1423 VCCCCY1HH3R0C∗X 3.0p50VCeramicAA
C1424 VCCCCY1HH270J∗ X 27p50VCeramicAA
C1425 VCCCCY1HH100D∗X 10p50VCeramicAA
C1428 VCKYCY1HF103Z∗ X 0.01 50VCeramicAA
C1435 VCKYCY1HF103Z∗ X 0.01 50VCeramicAA
C1436 VCKYCY1CF104Z∗ X 0.116VCeramicAA
C1439 VCE9GA1CW106M+X 1016VElect.(N,P)AB
C1440 VCEA0A1HW106M+X 1050VElectrolyticAA
C1441 VCKYCY1HF103Z∗ X 0.01 50VCeramicAA
C1442 VCFYFA1HA474J+ X 0.47 50VMylarAB
C1443 VCKYCY1HF103Z∗ X 0.01 50VCeramicAA
C1444 VCKYCY1HB472K∗ X 4700p 50VCeramicAA
C1445 VCKYCY1HF103Z∗ X 0.01 50VCeramicAA
C1446 VCCCCY1HH181J∗ X 180p 50VCeramicAA
C1447 VCKYCY1HF103Z∗ X 0.01 50VCeramicAA
C1448 VCKYCY1CF104Z∗ X 0.116VCeramicAA
C1449 VCKYCY1CF104Z∗ X 0.116VCeramicAA
C1451 VCEA0A1CW107M+X 10016VElectrolyticAA
C1452 VCKYCY1CF104Z∗ X 0.116VCeramicAA
C1453 VCKYCY1HF103Z∗ X 0.01 50VCeramicAA
C1454 VCKYCY1HF103Z∗ X 0.01 50VCeramicAA
C1455 VCKYCY1HF103Z∗ X 0.01 50VCeramicAA
C1456 VCKYCY1CF104Z∗ X 0.116VCeramicAA
C1457 VCEA0A1HW106M+X 1050VElectrolyticAA
C1458 VCEA0A1HW106M+X 1050VElectrolyticAA
C1460 VCKYCY1HF103Z∗ X 0.01 50VCeramicAA
C1470 VCCCCY1HH270J∗ X 27p50VCeramicAA
C1474 VCCCCY1HH150J∗ X 15p50VCeramicAA
RESISTORS
R1402 VRS-CY1JF000J∗ X 01/16W Metal Oxide AA
R1405 VRS-CY1JF361J∗ X 360 1/16W Metal Oxide AA
R1406 VRS-CY1JF102J∗ X 1k1/16W Metal Oxide AA
R1407 VRS-CY1JF102J∗ X 1k1/16W Metal Oxide AA
R1410 VRS-CY1JF473J∗ X 47k 1/16W Metal Oxide AA
R1411 VRS-CY1JF223J∗ X 22k 1/16W Metal Oxide AA
R1412 VRS-CY1JF102J∗ X 1k1/16W Metal Oxide AA
R1413 VRS-CY1JF122J∗ X 1.2k 1/16W Metal Oxide AA
R1414 VRS-CY1JF331J∗ X 330 1/16W Metal Oxide AA
R1415 VRS-CY1JF391J∗ X 390 1/16W Metal Oxide AA
R1416 VRS-CY1JF102J∗ X 1k1/16W Metal Oxide AA
R1421 VRS-CY1JF471F∗ X 470 1/16W Metal Oxide AA
R1423 VRS-CY1JF152F∗ X 1.5k 1/16W Metal Oxide AA
R1426 VRS-CY1JF000J∗ X 01/16W Metal Oxide AA
R1428 VRS-CY1JF332J∗ X 3.3k 1/16W Metal Oxide AA
R1429 VRS-CY1JF222J∗ X 2.2k 1/16W Metal Oxide AA
R1430 VRS-CY1JF473J∗ X 47k 1/16W Metal Oxide AA
R1431 VRS-CY1JF223J∗ X 22k 1/16W Metal Oxide AA
R1432 VRS-CY1JF102J∗ X 1k1/16W Metal Oxide AA
R1433 VRS-CY1JF122J∗ X 1.2k 1/16W Metal Oxide AA
R1434 VRS-CY1JF331J∗ X 330 1/16W Metal Oxide AA
R1435 VRS-CY1JF102J∗ X 1k1/16W Metal Oxide AA
R1436 VRS-CY1JF331J∗ X 330 1/16W Metal Oxide AA
R1438 VRS-CY1JF222J∗ X 2.2k 1/16W Metal Oxide AA
R1456 VRS-CY1JF564J∗ X 560k 1/16W Metal Oxide AA
R1457 VRS-CY1JF103J∗ X 10k 1/16W Metal Oxide AA
R1458 VRD-RA2BE103J∗ X 10k 1/8WCarbonAA
R1459 VRS-CY1JF821J∗ X 820 1/16W Metal Oxide AA
R1466 VRS-CY1JF103J∗ X 10k 1/16W Metal Oxide AA
R1467 VRS-CY1JF682J∗ X 6.8k 1/16W Metal Oxide AA
R1473 VRS-CY1JF102J∗ X 1k1/16W Metal Oxide AA
R1475 VRS-CY1JF102J∗ X 1k1/16W Metal Oxide AA
MISCELLANEOUS PARTS
FB1401RBLN-0061TAZZ∗ X Ferrite BeadAA
P1401 QPLGZ0810CEZZ X Plug, 8pinAB
No part of this publication may be reproduced,
stored in a retrieval system, or transmitted in
any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without
prior written permission of the publisher.
QRC0001-U
April. 2003
Changes : SEMEX
Design and Production Information
Design base : JAPAN
Production:SEMEX
J B
SHARP ELECTRONICA MEXICO S. A. DE C. V.
Quality & Reliability Control Center
Blvd. SHARP No. 3510 Parque Industrial Rosarito
Playas de Rosarito, México B. C. 22710
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.