SEA User 2 24V Hydro User Manual

®

Sistemi Elettronici

di Apertura Porte e Cancelli

International registered trademark n. 804888

Italiano

English

USER 2 - 24V DG

HYDRO

23024051/80

APPAR. ELETTRONICA 24V PER CANCELLI A BATTENTE

ELECTRONIC CONTROL UNIT 24V FOR SWING GATES

ARMOIRE ELECTRONIQUE 24 V POUR PORTAILS A BATTANTS

TARJETA ELECTRONICA 24V PARA CANCELA ABATIBLES

Français

Español

67411830

SEA S.p.A.

Zona Ind.le S. Atto - 64020 S. Nicolò a Tordino (TE)

Tel. [phone] - Fax [phone]

www.seateam.com

e-mail: [e-mail]

REV. 01 - 12/2015

Sistemi Elettronici

di Apertura Porte e Cancelli

International registered trademark n. 804888

®

English

DESCRIPTION OF THE COMPONENTS

TECHNICAL SPECIFICATIONS

Control unit power supply: 24V
Switching power pack input voltage: (90 - 132~ / 180 - 264~) 50/60 Hz
Absorption in stand by: 30 mA
Environment temperature : -20°C +50°C
Specifications of external enclosure: 305 x 225 x 125 mm - Ip55

100 mm

F1

USER 2 - 24V DG

HYDRO

RL1

MF1

RECEIVER RX

+ S -

CN5

CN1

13 12 11 10 9 8 7 6 5 4 3 2 1

MF2

MF3

MF4

DISPLAY

UP DOWN OK

RL2

RL3

RL4

CN3

CN2

EXP

156 mm

23 24 25 26

LE CARD

+ -

21 22

ON

1 2

POTENC

CNP

14 15 16 17 18 19 20

CN1

M2

I3 I4

GND

DS1

I2

5 6 7

3 8 9 10 11

1 2 4

P01 D1 P11 P02 D2 P12 I1

M1

CNA

JOLLY-JOLLY2

CN1 = Input/Output connector
CN2 = Limit switch, electro-lock connector
CN3 = Motors connector
CN5 = Battery charger connector and

Switching power pack

CNA = RX Receiver module connection
EXP = Expansion module connector/LE Card
JOLLY = Jolly-Jolly 2 programmer connector

67411830 REV 01 - 12/201524

PROG

JOLLY

MF1 - MF2 = Mosfet motor 2
MF3 - MF4 = Mosfet motor 1
PROG = Programming connector
RL1 - RL2 = Relay motor 2
RL3 - RL4 = Relay motor 1
F1 = Fuse 10AT

Sistemi Elettronici

di Apertura Porte e Cancelli

International registered trademark n. 804888

®

English

USER 2 - 24V DG

HYDRO

CONNECTIONS

14

CN2

15

16 17

Limit Switch closing M1

Limit Switch opening M1

Limit Switch opening M2

18 19

Limit Switch closing M2

13

Common

12

20

Electric lock

(12V 15VA max)

11 10

21

AUX

22

Light (+)

(24VL 500mA max)

9 8

23

(500 mA max)

CN1

7 6

CN3

24

25 26

M1 M2

5

4

3

2

1

+

28V Battery charger

CN5

S

Positive battery

-

Negative battery charger

AUX

Flash (-)

(24VL 500mA max)

WARNING: The control unit is designed with the automatic detection of not used N.C. inputs (Photocells, Stop and Limit
switch) except the SAFETY EDGE input. The exclude inputs in self-programming can be restored in the “Check inputs”
menu without need to repeat the programming (page 37).

24V Aux

Common

Edge

Photocell 2

(250 mA max)

JUMPERS

Photocell 1

Stop

Common

Start

Antenna

Ped. START

Common

CN1

12

13

Obligatory jumper
without accessory
connection.

Flash (-)

Optional

67411830 25REV 01 - 12/2015

AUX

(24VL 500mA max)

11 10

24V Aux

Common

(250 mA max)

9 8

Edge

Photocell 2

7 6

Photocell 1

5

4

Stop

Common

Ped. START

3

2

1

Start

Antenna

Common

The herein reported
functions are
available starting
from revision 43.

Sistemi Elettronici

di Apertura Porte e Cancelli

International registered trademark n. 804888

MENU

1

LANGUAGE

MENU

2

TRANSMITTERS

MENU

3

MENU

ONE SINGLE

4

MENU

5

UP

SEA

UP

SEA

UP

SEA

MOTOR

UP

SEA

LEAF

UP

SEA

REVERSE

MOTOR

UP

®

SET

OK

SEA

MENU

ITALIANO

SET

Skip this step if you do not want to program a transmitter

SET

OK

If on the display

appears the item:

SET

OK

SEA

MENU

SET

START

MENU

RECEIVER

MISSING

Choose the type of

motor with

UP or DOWN

OK

SEA

Skip this step if you are working in double leaf mode

SET

OK

SET

OK OK

With UP or DOWN choose

ON only if in single

leaf mode (Motor 1)

Choose ON with

UP or DOWN

if you want to reverse

the direction of

the motor rotation

English

PROGRAMMING

QUICK START

SEA

MENU

PRESS

BUTTON

Check if a receiver has

SET

been connceted

(see page 24)

OK

SET

Press the

button of the

TX to be

stored

To confirm and return

to main menu

OK

To confirm and return

To confirm and return

to main menu

SEA

MENU

STORED

to the main menu

SET

Menu or press

the next TX to

OK to exit

the button of

be stored

USER 2 - 24V DG

HYDRO

PROGRAMMING

BUTTONS

DOWNUP

OK

6

(See

page 27)

7

8

9

(See

page 27)

10

15

SEA

MENU

SET

LOGIC

UP

SEA

MENU

SET

PAUSE TIME

UP

SEA

MENU

SET

START IN

PAUSE

UP

SEA

MENU

SET

PROGRAM-

MING

UP

SEA

MENU

SET

TEST START

UP

SEA

MENU

SET

END

OK OK

choose

With UP or DOWN

To confirm and return

the desired logic

OK OK

With UP or DOWN
choose a delay for

To confirm and return

automatic closing

With UP or DOWN

OK OK

To confirm and return

Choose ON

OK OK

With UP or DOWN choose ON

to start times learning

The gate will execute a CLOSING-OPENING-CLOSING CYCLE

Skip this step if a TX has already been stored

OK OK

UP or DOWN Choose

OK

With

ON to start test

Press OK to return to the

display of the inputs state.

to main menu

to main menu

to main menu

the control unit returns automatically

To confirm and return to

Skip this step

if you want to work

in half-automatic

logic

At the end of the selflearning

to the main menu

main menu

UP

SEA

16

MENU

SPECIAL

MENU

SET

OK

Press OK to enter the special menu.

ALL OTHER PARAMETERS HAVE DEFAULT SETTINGS WHICH ARE USEFUL FOR THE 90% OF THE APPLICATIONS

BUT CAN BE HOWEVER SET THROUGH THE SPECIAL MENU. FOR ENTERING INTO THE SPECIAL MENU MOVE

ON ONE OF THE MENU AND PRESS THE UP AND DOWN BUTTONS AT THE SAME TIME FOR 5 S.

67411830

26

REV 01 - 12/2015

Sistemi Elettronici

di Apertura Porte e Cancelli

International registered trademark n. 804888

®

English

USER 2 - 24V DG

HYDRO

MENU FUNCTIONS TABLE USER 2 24V DG HYDRO

MENU

1 - LANGUAGE

2 - TRANSMITTERS

3 - MOTOR

SET

Italiano

English

Français

Español

Dutch

Start

Pedestrian Start

External module

Stop

Delete a transmitter

Clear memory

End

Hydraulic

Compact

HT270DC

Italian

English

French

Spanish

Olandese

Start

Pedestrian Start

External module

Stop

Delete single transmitter

Delete transmitter memory

“Transmitters” menu output

Hydraulic

Compact

Half Tank 270 DC

Description

HT390DC Half Tank 390 DC

Default

Italiano

Start

Pedestrian

Start

Ht270DC

Set value

4 - ONE SINGLE
LEAF *

5 - REVERSE MOTOR *

6 - LOGIC

(See page 29)

7 - PAUSE TIME

8 - START IN PAUSE

9 - PROGRAMMING

(See page 28)

Hydraulic R

Off

On

Off

On

Automatic

Open-stop-close-stop-open

Open-stop-close-open

2 buttons

Safety

Dead man

Off

1 240

Off

On

Off On

Hydraulic R

Disabled
In ON activates single leaf

mode (Motor 1)

Synchronized right motor

Synchronized left motor

Automatic

Step by step type 1

Step by step type 2

Two buttons

Safety

Dead man

OFF
(semi-automatic logics)

Setting from 1s to 4min.

In pause start is not acceped

In pause start is accepted

Times learning start

Off

Off

Automatic

Off

Off

Off

10 - TEST START

15 - END

16 - SPECIAL MENU

Off On

Press OK to return to the display of the firmware version

Press OK to enter the special menu.

Start command

and to the one of inputs state.

Off

Note 1: The * indicates that the default value or the menu may change depending on the selected motor type.

67411830 27

REV 01 - 12/2015

Sistemi Elettronici

di Apertura Porte e Cancelli

International registered trademark n. 804888

®

English

USER 2 - 24V DG

HYDRO

WORKING TIMES SELF LEARNING

Note1: Put a jumper on SAFETY EDGE contact if not used.
Note2: It is not necessary to put a jumper on the limit switches, photocells and Stop if they are not used.

1) Check the right operation of the accessories (photocells, buttons etc.). If necessary set the leaf delay.

2) If necessary adjust the selflearning speed.

3) Switch off power supply, release the motors and manually place the leaf on the middle of the stroke.
Restore the mechanical lock .

4) Power the control unit .

5) Choose the desired motor type; use (default HT270DC).

6) Select 9-PROGRAMMING on the display, press OK and then UP and DOWN to start the programming.

Note3: If on single leaf mode set 4-ONE SINGLE LEAF on ON.
Note4: If one or both motors start in opening, switch off power and invert the motor(s) cable starting in opening o

the function of menu

5-REVERSE MOTOR. Afterwards repeat the procedure starting from point 4.

7) Both leaves will start a CLOSE - OPEN - CLOSE cycle automatically (CLOSE M2 - CLOSE M1 - OPEN M1 ­OPEN M2 - CLOSE M2 - CLOSE M1). End of selflearning.

The control unit is pre-set with the default settings, to start the control unit with the DEFAULT
settings just keep pressed the UP and DOWN buttons at the same time power supplying the
control unit the display shows the message “Init”. The DEFAULT settings are shown in the
Menues table.

r use

SELFLERNING OPERATION TIME WITH POTENTIOMETER

When the potentiometer is installed, it is necessary to select “Potentiometer” in the 32-ENCODER menu. Start
programming and make sure that leaf 2 starts as first in closing. The gate will automatically execute the following cycle:
CLOSING M2 - CLOSING M1 - OPENING M1 - OPENING M2 - CLOSING M2 - CLOSING M1.

Note: For stop detection sensitivity setting refer to the special menu.

WORKING TIMES SELFLEARNING THROUGH IMPULSES (Required for SB version)

ATTENTION: This procedure is potentially dangerous and should only be performed by qualified people in
safety conditions.

When the potentiometer is installed, it is necessary to select “Potentiometer” in the 32-ENCODER menu.

1) Turn off electricity, release the motors and manually position the leaves on halfway.
Reset the mechanical lock.

2) Connect the control board to the power supply.

3) Select 9-PROGRAMMING on the display, press OK and than one of the UP or DOWN buttons.

4) At this point the gate will start the following cycle: CLOSING M2 - CLOSING M1 - OPENING M1 - OPENING M2 ­CLOSING M2 - CLOSING M1. During cycle, to store the respective stops, press UP or DOWN or START at every
point of stop of the leaf.

5) The self-learning is done.

6741183028 REV 01 - 12/2015

Sistemi Elettronici

di Apertura Porte e Cancelli

International registered trademark n. 804888

®

English

USER 2 - 24V DG

HYDRO

FUNCTION LOGIC

AUTOMATIC LOGIC

A start impulse opens the gate. A second impluse during the opening will not be accepted.
A start impulse during closing reverses the movement.

NOTE 1: To have the automatic closing it is necessary to set a pause time, otherwise all the logic will be semi­automatic.
NOTE2: It is possible to choose, whether to accept or not, the start in pause, selecting in the MENU the item 8­START IN PAUSE and choosing ON or OFF. By default, the parameter is OFF.

SECURITY LOGIC

A start impulse opens the gate. A second impulse during opening reverses the movement.
A start impulse during closing reverses the movement.

NOTE 1: To have the automatic closing it is necessary to set a pause time, otherwise all the logic will be semi­automatic.
NOTE2: It is possible to choose, whether to accept or not, the start in pause, selecting in the MENU the item 8­START IN PAUSE and choosing ON or OFF. By default, the parameter is OFF.

STEP BY STEP TYPE 1 LOGIC

The start impulse follows the OPEN-STOP-CLOSE-STOP-OPEN logic.

NOTE 1: To have the automatic closing it is necessary to set a pause time, otherwise all the logic will be semi­automatic.
NOTE2: It is possible to choose, whether to accept or not, the start in pause, selecting in the MENU the item 8­START IN PAUSE and choosing ON or OFF. By default, the parameter is OFF.

STEP BY STEP TYPE 2 LOGIC

The start impulse follows the OPEN-STOP-CLOSE -OPEN logic.

NOTE 1: To have the automatic closing it is necessary to set a pause time, otherwise all the logic will be semi­automatic.
NOTE2: It is possible to choose, whether to accept or not, the start in pause, selecting in the MENU the item 8­START IN PAUSE and choosing ON or OFF. By default, the parameter is OFF.

DEAD MAN LOGIC

The gate opens as long as the START button of opening is pressed; releasing it the gate stops. The gate closes as long
as the button connected to the PEDESTRIAN START is pressed; releasing it the gate stops. To execute complete
opening and/or closing cycles the related pushbuttons must be constantly pressed.

2 PUSHBUTTONS LOGIC

One start opens, one pedestrian start closes. In opening the closing will not be accepted. In closing a start command
reopens, a pedestrian start command (closes) will be ignored.

67411830 29REV 01 - 12/2015

Sistemi Elettronici

di Apertura Porte e Cancelli

International registered trademark n. 804888

®

English

USER 2 - 24V DG

HYDRO

SPECIAL MENU

PRESS AT THE SAME TIME FOR 5 SECONDS TO ENTER OR TO EXIT THE SPECIAL MENU

UPDOWN

SPECIAL MENU FUNCTIONS TABLE USER 2 24V DG HYDRO

For entering into the special menu move on one of the menu and press the

buttons at the same time for 5 s. For exiting the special menu move on one of the

menu and press the buttons at the same time for 5 s.

UP and DOWN

press END or

UP and DOWN

MENU SP

17 - OPENING SPEED 1 *

18 - CLOSING SPEED 1 *

19 - OPENING SPEED 2 *

20 - CLOSING SPEED 2 *
21 - OPENING SLOWDOWN
SPEED 1 *

22 - CLOSING SLOWDOWN
SPEED 1 *

23 - OPENING SLOWDOWN
SPEED 2 *

24 - CLOSING SLOWDOWN
SPEED 2 *

25 - LEARNING SPEED *
26 - LEAF DELAY IN
OPENING *

27 - LEAF DELAY IN
CLOSING *

28 - OPENING TORQ 1 *
29 - CLOSING TORQ 1 *

30 - OPENING TORQ 2 *

SET

30 100 75

30 100

30 100 75

30 100

30 100

30 100

30 100

30 100

30 100

Off 6

Off 20

10 100

10 100

10 100

Setting from 30 to 100

Setting from 30 to 100

Setting from 30 to 100

Setting from 30 to 100

Setting from 30 to 100

Setting from 30 to 100

Setting from 30 to 100

Setting from 30 to 100

Setting from 30 to 100

Setting from OFF to
6 seconds

Setting from OFF to
20 seconds

Opening torq M1

Closing torq M1

Opening torq M2

Description

Default

75

75

30

30

30

30

50

3

3

50

50

50

Set Value

31 - CLOSING TORQ 2 *

32 - ENCODER *

32 - ENCODER *

51 - I.PAR.M1 *

52 - I.AP.M1 *

53 - I.CH.M1 *

10 100
On

Potentiometer

- - - - - - - -

- - - - - - - -

- - - - - - - -

Closing torq M2

In ON enables the Encoder

Enables the reading of
the potentiometer with
LE card.

Reports the current position
of the potentiometer on the
leaf of motor 1.
This parameter is useful for
seeing if the potentiometer
is read correctly.

Reports the impulses
stored by the control unit
when the leaf of motor 1
is fully open.

Reports the impulses stored
by the control unit when the
leaf of motor 1is fully close.

50

Off

Off

30

67411830

REV 01 - 12/2015

Sistemi Elettronici

di Apertura Porte e Cancelli

International registered trademark n. 804888

®

English

USER 2 - 24V DG

HYDRO

MENU SP

54 - I.PAR.M2 *

55 - I.AP.M2 *

56 - I.CH.M2 *

32 - ENCODER *

33 - OPENING SENSITIVITY
MOTOR1 *

34 - CLOSING SENSITIVITY
MOTOR1 *

35 - OPENING SENSITIVITY
MOTOR2 *

36 - CLOSING SENSITIVITY
MOTOR2 *

46 - INVERSION *

SET

- - - - - - - -

- - - - - - - -

- - - - - - - -

Off

10% (Fast intervention)
99% (Slow intervention)

Off (Intervention excluded)

10% (Fast intervention)
99% (Slow intervention)

Off (Intervention excluded)

10% (Fast intervention)
99% (Slow intervention)

Off (Intervention excluded)

10% (Fast intervention)
99% (Slow intervention)

Off (Intervention excluded)

0 2000

Normal opening

Description

Reports the current position
of the potentiometer on the
leaf of motor 2.
This parameter is useful for
seeing if the potentiometer
is read correctly.

Reports the impulses
stored by the control unit
when the leaf of motor 2
is fully open.

Reports the impulses
stored by the control unit
when the leaf of motor 2
is fully close.

In OFF disables the Encoder

Adjusts the intervention time
of the Encoder / Potentiometer
on Motor 1 in opening

Disabled

Adjusts the intervention time
of the Encoder / Potentiometer
on Motor 1 in closing

Disabled

Adjusts the intervention time
of the Encoder / Potentiometer
on Motor 2 in opening

Disabled

Adjusts the intervention time
of the Encoder / Potentiometer
on Motor 2 in closing

Disabled

Allows you to adjust the
inversion space
calculated in pulses.

In case of inversion on obstacle
during closing the gate will
completely reopen and will
try for 3 times the reclosing.

Default

Off

Off

Off

Off

Off

500

Set Value

For the menus from number 51 to 56 see menu 32-ENCODER = Potentiometer

59 - OPENING SLOWDOWN 1

60 - CLOSING SLOWDOWN 1

61 - OPENING SLOWDOWN 2 *

62 - CLOSING SLOWDOWN 2 *

63 - DECELERATION

64 - ACCELERATION

67411830

Off 50

Off 50

Off 50

Off 50

0 %

100%

0 %

100%

REV 01 - 12/2015

From OFF to 50% of
the stroke

From OFF to 50% of
the stroke

From OFF to 50% of
the stroke

From OFF to 50% of
the stroke

Adjusts the transition
between the set speed
and slowdown

Acceleration ramp.
Adjusts the motor start.

20

20

20

20

30

0%

31