SEA Slide DG-SD User Manual

®

Sistemi Elettronici

di Apertura Porte e Cancelli

International registered trademark n. 804888

SLIDE DG (SD)

CONTROL UNIT FOR SLIDING GATES,

SWING GATES, BARRIERS AND GARAGE DOORS

English

67411696

SEA S.p.A.

Zona industriale 64020 S.ATTO Teramo - (ITALY)

Tel. [phone] r.a. Fax [phone]

www.seateam.com

[e-mail]

Rev.03 - 08/2015

®

English

Sistemi Elettronici

di Apertura Porte e Cancelli

International registered trademark n. 804888

COMPONENTS

TECHNICAL SPECIFICATIONS

Control unit power supply: 230 Vac ~ 50/60 Hz - 115Vac~ 50/60 Hz
Absorption in stand by: 30 mA
Environment temperature : -4°F +122°F / -20°C +50°C
Specifications of external enclosure: 183 X 238 X 120 - Ip55

SLIDE DG

(SD)

RECEIVER RX

155 mm

CNS

F1

TR1

CN5

MEM

CN3

R1

CN2

T1

R2

F2

JOLLY

CNA

CNS

CN1 = Input/output connectors
CN2 = Motor and courtesy light connector
CN3 = Power connector
CN5 = Encoder connector
CN6 =
CN7=

Pre-wired limit switch connector

Limit switch connector not pre-wired

CNA = UNI Receiver connector
CNS = RF FIX Receiver connector
CNP = Porgramming connector
JOLLY = Jolly and Jolly 2 connector
DS = Programming display

DS

CNP

JOLLY-JOLLY2

CN6

UP DOWN OK

CN7

CN1

85 mm

OK = Programming button
DOWN = Programming button
UP = Programming button
T1 = Motor piloting Triac
R1 = Relay C motor command

Courtesy light

R2 = Relay motor exchange
F1 = 6.3AT fuse on 230V/10AT on 115V
F2 = Accessories 1A fuse
TR1 = Power transformer
MEM = Remote controls memory (optional)

2

67411696

Sistemi Elettronici

di Apertura Porte e Cancelli

International registered trademark n. 804888

®

CONNECTIONS

English

SLIDE DG

(SD)

RADIO MODULE RF FIX

(CNS)

RF FIX

Receiver

connector

(Available from

hardware

revision R1)

1

ANT COM

CN2

17 16

LIGHT MOP MN MCL

Flash N

Motor 1 opening

2

3 4

START

PEDST

14

15

Motor 1 Neutral

M1

Motor 1 closing

CN1

5 6

STOP COM PH1 OPT1

7 8

CN3

L N

Line

Not connected

9

10

EDGE

OPT2 COM

Limit switch Closing 1 (Yellow)

Limit switch Opening 1 (Green)

Neutral

Limit switch Closing 1 (Yellow)

Limit switch Opening 1 (Green)

12

11

24V(FL)

13

FL(-)

24V (Red)

Common (White)

CN6

LIMIT SWITCH

1

CN7

OPT2 (-)

Start

Antenna

Common

Stop

Common

START Ped.

Photocell 1

Edge 1

OPT1 (Not connected)

Common

Flash (-)

24V (FL) (200 mA)

Accessories+flash led

JUMPERS

WARNING: before activating the control unit the STOP, PHOTOCELL and EDGE contacts must be closed.

CN1

2

1

ANT COM

3 4

START

5 6

PEDST

STOP COM PH1 OPT1

7 8

9

EDGE

10

11

OPT2 COM

12

24V(FL)

13

FL(-)

Obligatory jumper
without accessory
connection.

67411696

OPT2 (-)

Start

Antenna

Common

Stop

Common

START Ped.

Photocell 1

Edge 1

OPT1 (Not connected)

Common

Flash (-)

24V (FL) (200 mA)

Accessories+flash led

The herein reported
functions are
available starting
from revision 14.

3

Sistemi Elettronici

di Apertura Porte e Cancelli

International registered trademark n. 804888

®

English

SLIDE DG

(SD)

MENU FUNCTIONS TABLE SLIDE DG

MENU

1 - langvage

U

2 - trans tters

SET

tal ano

engl sk

fran(a s
espanol
dut(k
start
Pedestr an Start
stop

vnlo(k

U

Delete a trans itter

UU

(Lear e ory

U

Oue To eep

End

Description

Italian

English

French

Spanish

Dutch

Start

Pedestrian Start

Stop
Storing of a command

for unlocking an
electric brake

Delete single transmitter

Delete transmitter memory
Transfers the stored

transmitters on the control
unit to the external EEPROM
(MEM) if inserted.

“Transmitters” menu output

Default

tal ano

start

Ped Start.

Set value

3 - otor

U

4 - log (

(See page 7)

5 - paVse t e

kydravlI(
Sl d ng ra(K

REUERS BLE Sl d ng gate

U

Sl d ng AGNET ( ra(k

Sl d ng (ha n

U

Sl d ng ag (ha n
Tripkase - bVll
seagear

U

E(kan (

Hydraulic

Sliding rack

Reversible sliding gate

Sliding gate rack with
magnetic limit switch

Sliding chain

Sliding mag chain

Three-phase - Bull

Seagear

Hydraulic motors

Sl d ng

U

Avto at (

open-stop-(lose-stop-open

open-stop-(lose-open

2 bvttons
safety

U

Dead an

U

off

1 240

Automatic

Step by step type 1

Step by step type 2

Two buttons

Safety

Dead man

OFF
(semi-automatic logics)

Setting from 1s to 4min.

Open-stop­(lose-open

off

6 - start n pavse

off
on

U U

7 - progra ng

(See page 6)

8 - test start

Note: Menu 7 is activated with ECODER ON.

4

67411696

Off on

Off on

In pause start is not acceped

In pause start is accepted

Times learning start

Start command

off

off

off

Sistemi Elettronici

di Apertura Porte e Cancelli

International registered trademark n. 804888

®

English

SLIDE DG

(SD)

MENU

u

9 - opening ti e *

u

10 - (losing ti e *

11 - open ng torq *

12 - (los ng torq *

13 - BRAKE *

14 - pedestr an
open ng

U

15 - reuerse otor

16 - END

U

17 - spe(ial enu

5 300

5 300

10 100

10 100

Off 100

20 100

Off

On

SET

Description

Opening time

Closing time

Default

60

60

Opening torque
Note: with hydraulic motors

75

the torque will be on 100%

Closing torque
Note: with hydraulic motors

75

the torque will be on 100%
Adjusts the braking on the

limit switches

Setting from 20 to 100

Synchronized right motor

10

10

Off

Synchronized left motor

Select END and press OK to exit the special menu.

The special menu switches off automatically after 20 minutes.

Press OK to enter the special menu.

Set value

Note 1: The * indicates that the default value may change depending on the selected motor type.

67411696

5

Sistemi Elettronici

di Apertura Porte e Cancelli

International registered trademark n. 804888

®

WORKING TIMES SELF LEARNING

English

SLIDE DG

(SD)

The control unit is pre-set with the default settings, to start the control unit with the
DEFAULT settings just keep pressed the UP and DOWN buttons at the same time
power supplying the control unit the display shows the message init.
The DEFAULT settings are shown in the Menues table.

The electronic control unit is already configured without deceleration and with working time in opening and
closing of 60 seconds.
For starting the control unit all NC contacts must be closed, after which it will be sufficient to give the run
command.

Note: make sure that the limit switch corresponds to the direction of travel.

SELFLERNING OPERATION TIME WITH ENCODER

When an encoder is installed, it is necessary to select On in the En(oder menu, start programming and
make sure that leaf starts as first in closing. The gate will automatically execute the following cycle:
CLOSING - OPENING - CLOSING.
Note: For stop detection sensitivity setting refer to the special menu.

If the Encoder is active, the menu 9 and 10 show respectively the total and partial pulses. Menu 7 will allow
the programming through Encoder.

6

67411696