Scotts S2048, S2554 User Manual
L8
S2048 Yar d Tractor
and
S2554 Garden Tractor
Serial No. (010,001- )
OPERATOR’S MANUAL
OMM138757 L8
North American Version
Litho in U.S.A.
English
INTRODUCTION
THANK YOU for purchasing a Scotts
product.
Read this manual and your attachment manual
thoroughly. Failure to do so could result in personal
injury or equipment damage.
c
WARNING:
product contains chemicals known to the
The Engine Exhaust from this
State of California to cause cancer, birth
defects or other reproductive harm.
CALIFORNIA Proposition 65 Warning
This manual should be considered a permanent par t of
your machine and should remain with the machine when
you sell it.
Measurements in this manual are metric units and their
U.S. customary equivalents. RIGHT-HAND and LEFTHAND sides are determined by facing in the direction
the machine will travel when going forward. When you
see a broken line arrow (------>), it indicates the part it is
pointing to is hidden.
Record identification numbers below. Be sure to record
all the numbers to help in tracing the machine if it is
stolen. You also need to give these numbers to your
dealer when you order parts.
DATE OF PURCHASE: _______________________________
DEALER NAME: ____________________________________
DEALER PHONE: ___________________________________
TRACTOR SERIAL NUMBER (A), (Located on rear
of tractor):
ENGINE SERIAL NUMBER (B), (Located on engine):
__ __ __ __ __ __ __ __ __ __ __ __ __
__ __ __ __ __ __ __ __ __ __ __ __ __
B
A
Introduction
TABLE OF CONTENTS
Assembly...............................................................................................................................................1
Safety Signs...........................................................................................................................................5
Controls ................................................................................................................................................. 8
Operating Machine ................................................................................................................................9
Operating Mower.................................................................................................................................26
Replacement Parts............................................................................................................................. 32
Service Machine Safely.......................................................................................................................33
Service Interval Chart.......................................................................................................................... 35
Service Engine .................................................................................................................................... 37
Service Transmission........................................................................................................................... 44
Service Mower.....................................................................................................................................45
Service Electrical................................................................................................................................. 49
Service Miscellaneous.........................................................................................................................54
Removing Mower.................................................................................................................................62
Installing Mower...................................................................................................................................64
Troubleshooting ..................................................................................................................................65
Storing Machine...................................................................................................................................70
Specifications.......................................................................................................................................73
Warranty..............................................................................................................................................76
Index....................................................................................................................................................82
Service Literature ............................................................................................................................... 87
All information, illustrations and
specifications in this manual are based
on the latest information at the time of
publication. The right is reserved to
make changes at any time without
notice.
COPYRIGHT© 1998
Deere & Co.
Table of Contents
OMM138757 L8
NOTES
Notes
NOTES
Notes
NOTES
Notes
ASSEMBLY
M86467
A
Identify Parts
Clear Plastic Bag Contains:
• Scotts Operator’s Manual
• Engine Owner’s Manual
• Safety Video
• Warranty Cards
Bag of Parts Contains:
• Hardware for Steering Wheel
• Hardware for Battery Cables
• Key Chain
• Padded Key
NOTE: There is an extra ignition key strapped to
one of the seat suspension springs.
Check and Connect Battery
CAUTION: Prevent Battery Explosions:
c
- Keep sparks, lighted matches, and open
flame away from the top of battery. Battery
gas can explode.
- Never check battery charge by placing a
metal object across the posts. Use a voltmeter or hydrometer.
- Do not charge a frozen battery; it may
explode. Warm battery to 16 degrees C (60
degrees F).
IMPORTANT: This battery comes fully charged. If
the mower is not used by the Service Expiration
Date indicated on the battery, charge the battery.
(See Charging the Battery in the Service Electrical section.)
Check Battery
Battery is filled with acid and charged when it left the
factory. If necessary, charge the battery prior to
operation. (See Charging the Battery in ServiceElectrical Section.)
Locate label attached to battery. Find the service
expiration date information (A).
If battery is put into service after date shown, charge the
battery for a minimum of 1 hour at 6 - 10 amps.
Check battery voltage. Battery is fully charged at 12.6
volts.
Assembly - Page 1
ASSEMBLY
M97159
B
C
A
M88566
A
B
Connect Battery
NOTE: Do not remove the BLACK negative (–)
protective cap at this time.
1. Remove and discard the RED positive (+) protective
cap from the positive (+) battery terminal.
CAUTION: DO NOT attempt to open, add fluid
c
or service battery. Any attempt to do so will
void warranty and lead to possible injury.
2. Connect blue harness wire (A) and RED positive (+)
cable (B) to battery. Apply petroleum jelly or silicone
spray to terminal to prevent corrosion. Make sure
connection is tight. Install the red terminal cover.
3. Remove and discard the BLACK (–) protective cap
from the negative battery terminal.
4. Connect black negative (–) cable (C) to battery. Apply
petroleum jelly or silicone spray to terminal to prevent
corrosion. Make sure connection is tight.
Install Steering Wheel
1. Put front wheels in the straight forward position.
2. Lubricate the steering shaft.
3. Install steering wheel with logo in the upright position.
4. Install shoulder bolt (A). Drive bolt in until head of bolt
contacts steering wheel.
5. Install washer and nut (B).
6. Tighten lock nut until it is snug. Do not tighten lock nut
to pull washer or head of bolt into steering wheel.
Assembly - Page 2
M97157
A
M97167
B
A
ASSEMBLY
Check Engine Oil
IMPORTANT: To avoid engine damage, DO NOT
run engine if oil level is below ADD mark.
1. Lift hood.
Picture Note: Model S2048 used for photo purposes.
2. Remove dipstick (A). Wipe with clean cloth.
3. Insert the dipstick into the tube and rest the oil fill cap
on the tube. Do not thread the cap onto the tube.
4. Remove dipstick to check oil level.
5. Oil must be between ADD and FULL marks.
6. Add oil to FULL mark if necessary. DO NOT overfill.
(See See Engine Oil in Service Engine section.)
7. Install and tighten dipstick. Lower hood.
Break-In Electric PTO Clutch
Picture Note: Model S2554 used for photo purposes.
1. Start engine and push throttle lever (A) up to full
throttle (
2. With no load on mower, ENGAGE PTO (B) and allow
mower to run for 10 seconds.
3. DISENGAGE PTO and wait 10 seconds.
4. Repeat Steps 2 and 3 for 12-15 cycles.
5. PTO clutch is now properly burnished.
r
) position.
Assembly - Page 3
ASSEMBLY
Check Machine Safety System
Perform safety system check to make sure the
electronic safety interlock circuit is functioning properly.
Perform all six Tests. (See Testing Safety System in the
Operating section.)
Checking Tire Pressure
CAUTION: Explosive separation of a tire and
c
rim parts can cause serious injury or death:
- Do not attempt to mount a tire without the
proper equipment and experience to perform
the job.
- Always maintain the correct tire pressure.
Do not inflate the tires above the
recommended pressure. Never weld or heat a
wheel and tire assembly. The heat can cause
an increase in air pressure resulting in a tire
explosion. Welding can structurall y weaken or
deform the wheel.
- When inflating tires, use a clip-on chuck and
extension hose long enough to allow you to
stand to one side and NOT in front of or over
the tire assembly.
- Check tires for low pressure, cuts, bubbles,
damaged rims or missing lug bolts and nuts.
1. Check tires for damage.
2. Check tire pressure with an accurate gauge.
3. Add or remove air, if necessary:
Tire Size Pressure
Model S2048:
Front = 16 x 6.5 x 8
Rear = 23 x 9.50 x 12
Models S2554:
Front = 16 x 7.5 x 8
Rear = 24 x 12 x 12
97 kPa (14 psi)
83 kPa (12 psi)
83 kPa (12 psi)
69 kPa (10 psi)
Assembly - Page 4
SAFETY SIGNS
Safety-Alert Symbol
Read and recognize safety information. Be alert to the
potential for personal injury when you see this safetyalert symbol.
On your machine safety labels, the words DANGER,
WARNING, and CAUTION are used with this safetyalert symbol. DANGER identifies the most serious
hazards.
In this manual, the word CAUTION and this symbol call
attention to safety messages.
Machine Safety Labels
DANGER
ROTATING BLADES CUT OFF ARMS AND LEGS
• Do not mow when children or others are around
• Do not mow in reverse
• Look down and behind before and while backing
• Never carry children
WARNING
AVOID SERIOUS INJURY OR DEATH
• Drive up and down slopes, not across
• Avoid sudden turns
• If machine stops going uphill, stop blade and back
down slowly
• Keep safety devices (guards, shields, and switches)
in place and working
• Read operator’s manual
• When leaving machine:
–Stop engine
–Set park brake
–Remove key
M97152
Safety Signs - Page 5
SAFETY SIGNS
WARNING
LOADED SPRING
LOCK LIFT LEVER FORWARD BEFORE CHANGING
ATTACHMENTS
Picture Note: One decal on each side of tractor frame.
M97152
DANGER/POISON
SHIELD EYES.
EXPLOSIVE GASES CAN
CAUSE BLINDNESS OR
INJURY.
NO
•SPARKS
• FLAMES
• SMOKING
SULFURIC ACID
CAN CAUSE BLINDNESS OR
SEVERE BURNS
FLUSH EYES IMMEDIATELY WITH WATER.
GET MEDICAL HELP FAST.
MAINTENANCE-FREE
KEEP OUT OF THE REACH OF CHILDREN. DO NOT
TIP. DO NOT OPEN BATTERY!
Picture Note: Located on Battery
M97152
Safety Signs - Page 6
SAFETY SIGNS
1-1996
DANGER
ROTATING BLADE
DO NOT PUT HANDS OR FEET UNDER OR INTO
MOWER WHEN ENGINE IS RUNNING
THROWN OBJECTS
BEFORE MOWING, CLEAR AREA OF OBJECTS THAT
MAY BE THROWN BY BLADE
DO NOT OPERATE MOWER WITHOUT DISCHARGE
CHUTE OR ENTIRE GRASS CATCHER IN PLACE
DANGER
M97152
ROTATING BLADE
DO NOT PUT HANDS OR FEET UNDER OR INTO
MOWER WHEN ENGINE IS RUNNING
Picture Note: Located on Left-Hand side of deck.
Certification Label
This OPEI label on your mower indicates that this model
has been certified by an independent laboratory for
compliance with American National Standard B-71.11996, “Safety Specifications” for Power Lawn Mowers,
Lawn and Garden Tractors, and Lawn Tractors.
M97152
Safety Signs - Page 7
Controls
M97167
F
G
C
D
E
A
B
Picture Note: Model S2554 used for photo purposes.
A - Engine Oil Pressure Light (Model S2554 Only)
B - Hour Meter (Model S2554 Only)
C - Battery Discharge Light
D - Light Switch
E - PTO Switch/RIO Switch
F - Choke Knob
G - Throttle Lever
H-Key Switch
I - Park Brake Lever
J - Brake Pedal
K - Forward Travel Pedal
L - Reverse Travel Pedal
M - Mower Deck Lift Lever
CONTROLS
N - Cut Height Adjustment Lever
H
I
K
L
M
J
M97165
N
M97160
Controls - Page 8
OPERATING MACHINE
Operate Safely
• In addition to reading your Operator’s Manual, view
your Mowing Safety Video.
• Check brake action before you operate. Adjust or
service brakes as necessary.
• Inspect machine before you operate. Be sure
hardware is tight. Repair or replace damaged, badly
worn, or missing parts. Be sure guards and shields are
in good condition and fastened in place. Make any
necessary adjustments before you operate.
• Clear work area of objects that might be thrown. K eep
people and pets out of the work area. Stop machine if
anyone enters the area.
• If you hit an object, stop the machine and inspect it.
Make repairs before you operate. Keep machine and
attachments properly maintained and in good working
order.
• DO NOT leave machine unattended when it is
running.
• Only operate during daylight or with good artificial
light.
• Be careful of traffic when operating near or crossing
roadways.
• Do not wear radio or music headphones while
operating the machine. Safe operation requires your full
attention.
Park Safely
• Stop machine on a level surface, not on a slope.
• Disengage mower blades.
• Lower attachments to the ground.
• Engage park brake.
• STOP engine.
• Remove key.
• Before you leave the operator’s seat, wait for engine
and all moving parts to STOP.
Operating Machine - Page 9
OPERATING MACHINE
Rotating Blades are Dangerous - Protect Children and Prevent Accidents
PROTECT CHILDREN:
• Nev er assume that children will remain where you last
saw them. Children are attracted to mowing activity, stay
alert to the presence of children.
• Keep children in the house when you are operating
the machine.
• Turn machine off if a child enters the mowing area.
• Use extra care when you come to blind corners,
shrubs, trees, or other objects that may block your
vision.
• DO NOT let children or an untrained person operate
the machine.
• DO NOT carry or let children ride on machine or any
attachment. DO NOT tow children in a cart or trailer.
HELP PREVENT SERIOUS OR FATAL ACCIDENTS:
• Be alert at all times, drive forward carefully. People
especially children can move quickly into the mowing
area before you know it.
• Back carefully. Disengage mower blades and look
behind the machine carefully, especially for children,
before you back up.
• DO NOT mow in reverse unless it is absolutely
necessary.
• Disengage mower blades when you are not mowing.
• DO NOT operate machine if you are under the
influence of drugs or alcohol.
Operating Machine - Page 10
OPERATING MACHINE
Avoid Tipping
• DO NOT drive where machine could slip or tip.
• Stay alert for holes and other hidden hazards in the
terrain.
• Keep away from drop-offs.
• Slow down before you make a sharp turn or operate
on a slope.
• When pulling loads or using heavy equipment, use
only approved hitches, limit loads to those you can
safely control, and use counterweights or wheel
weights when required per this manual or your
attachment manual.
• Drive up and down a hill—not across. Be careful
when you change direction on a slope.
• DO NOT stop when going up hill or down hill. If
machine stops going up hill, DISENGAGE mower
blades and back down slowly.
• DO NOT mow wet grass. Reduced traction could
cause sliding.
• DO NOT try to stabilize the machine by putting your
foot on the ground.
Keep Riders Off
• Only allow the operator on the machine. Keep
riders off.
• Riders on the machine or attachment may be struck
by foreign objects or thrown off the machine causing
serious injury.
• Riders obstruct the operator’s view resulting in the
machine being operated in an unsafe manner.
Operating Machine - Page 11
OPERATING MACHINE
M97164
A
Wear Appropriate Clothing
• Wear close fitting clothing and safety equipment
appropriate for the job.
• Loud noise can cause impairment or loss of hearing,
wear a suitable protective device such as earplugs.
Transport Safely
• Use safety lights and de vices . Slow mo ving machines
when driven on public roads are hard to see, especially
at night. Avoid personal injury or death resulting from a
collision with a vehicle.
• Whenever driving on public roads, use flashing
warning lights and turn signals according to local
regulations. Extra flashing warning lights may need to
be installed.
Adjusting Seat
1. Tip seat forward and loosen two knobs (A) to slide
seat assembly forward or rearward to most comfortable
OPERATOR position.
2. Tighten knobs after adjustment to keep seat in place.
Operating Machine - Page 12
OPERATING MACHINE
M97165
B
A
M97167
A
Using the Park Brake
CAUTION: The machine may begin to move
c
when engine is shut off and park brake is not
engaged. To avoid injury, always LOCK park
brake before getting off tractor or leaving
tractor unattended.
LOCKING PARK BRAKE:
1. Push brake pedal (A) all the way down.
2. Lift park brake lever (B) up.
3. Release pedal and park brake lever. Pedal should
stay down and park brake lever should stay LOCKED in
UP position.
UNLOCKING PARK BRAKE:
1. Push and hold brake pedal (A) down.
2. Push park brake lever (B) down to UNLOCK park
brake.
3. Release pedal.
Using Headlights
Picture Note: Model S2554 used for photo purposes.
Push top of light switch (A) to turn headlights ON.
Push bottom of light switch to turn headlights OFF.
Operating Machine - Page 13
M97167
B
A
C
M97167
B
A
C
D
OPERATING MACHINE
Checking Indicator Lights and Hour Meter
Picture Note: Model S2554 used for photo purposes.
b
•(
when throttle lever is moved to the HIGH IDLE/Mowing
(
several minutes while the battery is being charged.
•(
will come on when engine starts and should go out
within 5 seconds.
If indicator lights stay on longer than given time, STOP
engine.
• HOUR METER (C), on Model S2554 only, shows the
number of hours the engine has run. To display hours,
key must be in the “ON” position. Check the hour meter
daily to see what services need to be done.
) BATTERY DISCHARGE light (A) should go out
a
) position. The voltage light may remain on for
o
) OIL PRESSURE light (B), on Model S2554 only,
Starting Engine
CAUTION: Engine exhaust fumes can cause
c
sickness or death. • If it is necessary to run an
engine in an enclosed area, remove the
exhaust fumes from the area with an exhaust
pipe extension. • If you do not have an
exhaust pipe extension, open the doors and
get outside air into the area.
IMPORTANT: Do not operate starter more than 20
seconds at a time, or you may damage it. If engine
does not start: Wait two minutes before you try
again. See Troubleshooting section.
Picture Note: Model S2554 used for photo purposes.
1. Lock the park brake or depress brake pedal.
2. Push PTO switch (A) down to DISENGAGE.
k
3. Pull choke knob (B) out to the ON (
) position.
R
4. Move throttle lever (C) to the HALF-SPEED (
)
position.
5. Turn key (D) to START position.
6. When engine starts, release key to RUN position.
Operating Machine - Page 14
M97151
A
M97151
A
B
OPERATING MACHINE
7. Check starting conditions:
If engine is COLD:
•
the OFF position after the engine starts and warms
up.
If engine is WARM:
•
position as soon as the engine starts.
8. Let engine run for a couple of minutes to warm-up
before operating machine.
Warming and Idling Engine
WARMING ENGINE:
Picture Note: Model S2554 shown for photo purposes.
• Run Engine at half speed for 2–3 minutes.
IDLING ENGINE:
Gradually return the choke to
Return choke to the OFF
• Engine is air-cooled and needs a large volume of air
to keep cool. K eep air intake screen (A) on top of engine
clean.
• Avoid unnecessary engine idling.
Stopping Engine
1. STOP tractor travel.
2. Move throttle lever (A) MIDWAY between slow (
and fast (
r
) positions. Let the engine run a minimum of
15 seconds.
Picture Note: Model S2554 shown for photo purposes.
3. Turn key (B) to OFF position.
4. LOCK the park brake.
5. Remove key.
t
)
Operating Machine - Page 15
OPERATING MACHINE
M97165
B
A
C
Using and Stopping Automatic Transmission
CAUTION: TO AVOID INJURY:
c
• Before moving forward or rearward, make
sure area is clear of bystanders, especially
children.
• Disengage mower before backing up.
UNLOCK park brake.
To Travel Forward:
6.
• Slowly push down f orward pedal (A). Tractor will travel
faster the farther down you push the pedal.
• Release forward pedal, tractor will automatically
return to neutral and STOP.
To Travel in Reverse:
NOTE: The engine and any operating attachment
will stop as the REVERSE pedal is depressed with
attachment engaged.
1. Bring the vehicle to a stop.
2. Push PTO knob down to the OFF position to
disengage attachment.
3. Look behind the vehicle to be sure there are no
bystanders nearby.
4. Push down reverse pedal (B).
For Emergency Stopping:
• Release either travel pedal. Tractor will automatically
return to neutral and STOP.
• Push down on brake pedal (C). Tractor brakes will be
applied to assist in stopping.
Operating Machine - Page 16
OPERATING MACHINE
A
M97165
M97163
B
Pushing Machine
IMPORTANT: Avoid transmission damage, DO
NOT tow machine.
To move machine when engine is STOPPED:
• Unlock the park brake (A).
• Pull out on free-wheeling lever (B).
• Push machine to desired location.
NOTE: Push free-wheeling lever (B) in before
operating tractor.
Operating Machine - Page 17
OPERATING MACHINE
g
p
p
g
M96052
A
Using Reverse Implement Option
CAUTION: TO AVOID INJURY:
Before moving forward or rearward, make
c
sure area is clear of bystanders, especially
children.
NOTE: Operating the mower while backing up is
strongly discouraged. The Reverse Implement
Option should be used ONLY when operating
another attachment or when the operator deems it
necessary to reposition the machine with the mower
engaged.
1. Stop the machine FORWARD travel with the
attachment still engaged.
2. Look behind the vehicle to be sure there are
bystanders
3. Lift and hold the PTO knob (A) up past the PTO
engagement position to activate the reverse implement
position while depressing REVERSE foot pedal slightly.
NOTE:
re
ositioning the machine, return PTO knob to the
OFF
The En
4. As the machine begins to move backward, release
the PTO knob and reposition the machine.
5. Resume FORWARD travel. The attachment should
continue operating.
6. Repeat Steps 1 through 5 to reposition the machine
again.
.
If the en
osition and restart the machine. (See Starting
ine in this section.) Begin again with Step 2.
ine and attachment stop while
no
Daily Operating Checklist
• Test safety systems.
• Check tire pressure.
• Check fuel level.
• Check engine oil level.
• Remove grass and debris from machine.
Operating Machine - Page 18
OPERATING MACHINE
M97167
A
B
C
Testing Safety Systems
CAUTION: Engine exhaust fumes can cause
c
sickness or death. • If it is necessary to run an
engine in an enclosed area, remove the
exhaust fumes from the area with an exhaust
pipe extension. • If you do not have an
exhaust pipe extension, open the doors and
get outside air into the area.
NOTE: Your Tractor is equipped with a
ELECTRONIC SAFETY INTERLOCK. Engine will not
start unless: PTO switch is DISENGAGED; Brake
pedal is depressed OR parking brake is set.
Use the following checkout procedure to check for
normal operation of tractor.
If there is a malfunction during one of these procedures,
DO NOT operate tractor. (Contact your Authorized
Service Center for service.)
Perform these tests in a clear open area. Keep
bystanders away
.
Test 1
Check operation of indicator lights:
1. Turn key to RUN position.
Picture Note: Model S2554 used for photo purposes.
2. LOOK:
• Engine Oil Pressure Light (A), on Model S2554
Only, MUST light.
• Battery Discharge Light (B) will momentarily light,
this indicates the system is functioning properly. If the
light remains on start engine and move throttle to high
idle, the light should go out.
NOTE: The battery discharge light may remain on
for several minutes while the battery is being
charged.
3. If one indicator does not light, see Replacing Indicator
Light Bulb in Service – Electrical section.
4. If new indicator bulb does not light or no indicators
work, contact your Authorized Service Center for
service.
Operating Machine - Page 19
M97167
A
M97167
A
M97167
A
B
OPERATING MACHINE
Test 2
Picture Note: Model S2554 used for photo purposes.
1. Operator on seat.
2. UNLOCK the park brake.
3. Push PTO switch (A) down to DISENGAGE.
4. Try to start engine.
5. Engine MUST NOT start. If engine starts, there is a
problem with your safety interlock circuit.
Test 3
Picture Note: Model S2554 used for photo purposes.
1. Operator on seat.
2. LOCK the park brake.
3. Pull PTO switch (A) up to ENGAGE.
4. Try to start engine.
5. Engine MUST NOT start. If engine starts, there is a
problem with your safety interlock circuit.
Test 4
Picture Note: Model S2554 used for photo purposes.
1. Operator on seat.
2. LOCK the park brake.
3. Push PTO switch (A) down to DISENGAGE.
4. Start engine and move throttle lever (B) to HALF-
R
SPEED (
5. Pull PTO switch (A) up to ENGAGE.
6. Move throttle lever (B) to FAST (
7. Raise up off of seat. DO NOT get off tractor.
) position.
r
) speed position.
8. Engine MUST stop. If engine does not stop, there is a
problem with your safety interlock circuit.
Operating Machine - Page 20
M97165
A
C
M97167
B
D
M97167
A
B
A
M97165
OPERATING MACHINE
Test 5
1. Operator on seat.
2. Push brake pedal (A) down.
Picture Note: Model S2554 used for photo purposes.
3. Push PTO switch (B) down to DISENGAGE.
4. Release forward travel pedal (C) to N (NEUTRAL)
position.
5. Start engine and move throttle lever (D) to FAST (
r
speed position.
6. Release brake slowly.
7. Raise up off of seat. DO NOT get off tractor.
8. Engine MUST stop. If engine does not stop, there is a
problem with your safety interlock circuit.
Test 6
1. Operator on seat.
2. Lock the park brake.
Picture Note: Model S2554 used for photo purposes.
3. Push PTO switch (A) down to DISENGAGE.
r
4. Start engine and move throttle lever (B) to FAST (
speed position.
)
)
5. Raise up off of seat. DO NOT get off tractor.
6. Engine MUST remain running. If engine does stop,
there is a problem with your safety interlock circuit.
Test 7
1. LOCK the park brake (A).
2. Pull out free-wheeling lever.
3. Try to push machine manually.
4. Park brake MUST prevent machine from moving. If
machine moves, parking brake needs to be adjusted.
Operating Machine - Page 21
OPERATING MACHINE
Test 8
CAUTION: TO AVOID INJURY: Before moving
c
rearward, make sure area is clear of
bystanders, especially children.
Test Reverse Implement Option:
1. Start engine.
2. Engage PTO to start attachment.
3. Look behind the vehicle to be sure there are no
bystanders.
4. Begin REVERSE travel by depressing REVERSE foot
pedal.
5. Attachment and engine should stop operation. If
attachment or engine continues to operate while tractor
travels in REVERSE, do not continue to operate
attachment. See your Authorized service center for
service.
Avoid Damage to Plastic and Painted Surfaces
• DO NOT wipe plastic parts unless rinsed first. (See
Correct Cleaning Care in Service-Miscellaneous
section.)
• Insect repellent spray may damage plastic and
painted surfaces. Do not spray insect repellent near
machine.
• Be careful not to spill fuel on machine. Fuel may
damage surface. Wipe up spilled fuel immediately.
Operating Machine - Page 22
OPERATING MACHINE
Avoid Using Ground Engaging Equipment (Model S2048 Only)
IMPORTANT: Your S2048 tractor is NOT intended
for use with ground engaging equipment. Use of
such equipment could result in damage to
transmission components.
Tractor Model S2048 is not intended for use with ground
engaging equipment such as a rear tiller, disk, dirt blade
or plow.
Using Front Weights
CAUTION: Tractor front wheel weights
c
improve stability in most slope operation. To
avoid injury, add front wheel weights for
better front-end stability and steering when
using a rear mounted attachment or pulling a
cart.
NOTE: Before installing wheel weights on your
machine, MAKE SURE that the tire valve stems are
facing the inside.
Install front wheel weights for better stability and
steering control when you use equipment such as the
rear-mounted grass bagger or dumpcart.
Remove front wheel weights when not required.
Using Rear Wheel Weights
IMPORTANT: When adding weight to rear of
tractor, use wheel weights only.
34 kg (75 lbs.) MAX. each wheel.
Use of rear wheel weights is recommended when an
attachment, such as snowthrower or snow blade is
used.
Operating Machine - Page 23
Loading...