Schneider Electric XARS8L12W, XARS8L12H, XARS8D18H, XARS12D18W, XARS8D18W User Manual

...

XARS8D18p / XARS12D18p / XARS8L12p

Quick Start Guide

XARS8D18W / XARS8D18H / XARS12D18W / XARS12D18H XARS8L12W / XARS8L12H

Harmony eXLhoist

www.schneider-electric.com/control

www.schneider-electric.com

DANGER

HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH

p Disconnect all power from all equipment including connected devices, prior to removing any covers or doors, or installing or removing any accessories, hardware, cables, or wires except under the specific conditions specified in the appropriate hardware guide for this equipment. p Always use a properly rated voltage sensing device to confirm the power is off where and when indicated. p Replace and secure all covers, accessories, hardware, cables, and wires and confirm that a proper ground connection exists before applying power to the unit. p Use only the specified voltage when operating this equipment and any associated products.

Failure to follow these instructions will result in death or serious injury.

It is recommended to charge the battery once a week, for a duration of at least 4 hours.

Electrical equipment should be installed, operated, serviced, and maintained only by qualified personnel. No responsibility is assumed by Schneider Electric for any consequences arising out of the use of this material. You can download our technical user guide file as well as the eXLhoist configuration software from our website at www.schneider-electric.com.

UNINTENDED EQUIPMENT OPERATION

p Use appropriate safety interlocks where personnel and/or equipment hazards exist. p Install and operate this equipment in an enclosure appropriately rated for its intended environment.

p Do not disassemble, repair, or modify this equipment. p Do not connect any wiring to unused connections, or to connections

designated as Not Connected (N.C.).

Failure to follow these instructions can result in death, serious injury, or equipment damage.

WARNING

UNINTENDED EQUIPMENT OPERATION

Power line must be wired and protected with fuse or thermal magnetic switch (ex: Schneider-Electric GV2) in compliance with local and national regulatory requirements for the rated current and voltage of the particular equipment.

Failure to follow these instructions can result in death, serious injury, or equipment damage.

WARNING

UNINTENDED EQUIPMENT OPERATION

Put the remote into STOP mode when not operating the unit to avoid accidental operations of motions push buttons.

Failure to follow these instructions can result in death, serious injury, or equipment damage.

Note: You can decrease the "stand-by time out" value using the configuration software tool to reduce the time the remote is in run mode.

ZART8D ZARB18W

XARS8D18W

NHA45689 02 09 - 2016

ZART8D

XARS8D18H

ZART8L ZART8LZARB12W ZARB12H

XARS8L12W

ZARB18H

ZART12D ZART12D

XARS12D18W

ZARB18W

XARS12D18H

XARS8L12H

1/8

ZARB18H

XARS8D18p / XARS12D18p / XARS8L12p

Main characteristics

WARNING

UNINTENDED EQUIPMENT OPERATION

Install and operate this equipment according to the environmental conditions described in the operating limits.

Failure to follow these instructions can result in death, serious injury, or equipment damage.

Base station ZARBppp

272 (ZARBpW)

10.7

264,8 (ZARBpH)

in.

10.42

9.5

241,2

291

11.46

87,6

3.44

ZARB••H

ZARB••W

www.schneider-electric.com

STATUS

COM

POWER

356 12

STATUS

COM

POWER

1 : M12 for external antenna (covered by cap) 2 : Status LEDs 3 : M20 for the safeguarding function input wires (covered by cap) 4 : 62 pins connector 5 : M25 for output wires (covered by cable gland) 6 : M25 for detected applicative alarms input wires (covered by cap)

Specifications

Details Values

ZARB12H ZARB12W ZARB18H ZARB18W

Operating voltage Current consumption

(maximum current in connected or not connected state)

AC/DC power supply Min…max For 24V DC For 24V AC For 48V DC

24...48 V AC/DC ± 20%

24...240 V AC/DC ± 20%

For 48V AC For 240V DC For 240V AC

Operating temperature

For 24...48 V AC/DC power supply For 48...130 V AC/DC power supply For 130...240 V AC/DC power supply

Degree of protection IP65 / NEMA 4

--44 mA 44 mA

--250 mA 250 mA

-25...70°C (-13...158°F)

-25...50°C (-13...122°F)

Remote control ZARTppp

in.

323

12.72

3.62

111

4.37

Specifications

Operating radio range Operating temperature

Details Values

Free field

Operating temperature to charge battery 10...40°C (50...104°F)Office environment Degree of protection

- IP65 / NEMA 4

24...48 V AC/DC ± 20% 328 mA 535 mA 155 mA 312 mA

ZART8L ZART8D ZART12D

> 300 m

-20...60°C (-4...140°F)-

24...240 V AC/DC ± 20%

-25...70°C (-13...158°F)

-25...50°C (-13...122°F)

Charger for remote device

36,0 ± 1

1.42 ± 0.04

in.

NHA45689 02 09 - 2016

53,0 ± 1

2.09 ± 0.04

99,0 ± 1

102,0 ± 1

3.90 ± 0.04

4.02 ± 0.04

900 - 1000

35.43 - 39.37

Output Plug :

Ø 5.5 x Ø 2.5 x 11.0 mm

Inner Positive

8,0 ± 1

0.31 ± 0.04

Specifications

Operating voltage Operating temperature Degree of protection

2/8

Details Values

Office environment

110 / 240 VAC

0...40°C (32...104°F) IP20

XARS8D18p / XARS12D18p / XARS8L12p

Wiring

WARNING

UNINTENDED EQUIPMENT OPERATION

p Use shielded cables wherever specified for inpunts and outputs connections. p Properly ground the cable shields as indicated in the related documentation. p Route I/O cables separately from power cables.

Failure to follow these instructions can result in death, serious injury, or equipment damage.

Base station terminal wiring

ZARB18W

Q0B_1

Q0B_2

Q0A_1

AC_Neutral /-

AC_Phase /+

Q0A_2

CC_X

CT_1

CT_3

CT_2

CC_Y

CT_4

CT_6

www.schneider-electric.com

WARNING

UNINTENDED EQUIPMENT OPERATION

Connect the Base Station protective earth ground connection to the machine ground.

Failure to follow these instructions can result in death, serious injury, or equipment damage.

IN_COM

S2_S3

IN0

CT_8

CT_9

CT_7

CC_Z

CT_5

CC_10

CC_11

CT_10

CT_11

CT_12

CC_12

CT_13

CC_13

CT_14

CC_14

CT_15

CC_15

CT_16

CC_16

CT_17

CC_17

CT_18

CR_17

IN_COM

IN0

CC_18

IN_COM

S2_S3

IN14

CR_18

IN18

IN13

IN10

IN17

IN9

IN11

IN15

IN12

IN7

IN16

IN8

IN4

IN6

IN2

IN5

IN3

IN1

ZARB12W

Base station ZARBppH - Connector pin out

A : Pin number B : ZARB18H description C : ZARB12H description

10 11 12 13 14 15 16

CR_18 - -

CC_18

CT_18

CT_13

CR_17

CC_17

CT_17

CC_13

CT_14

CC_12 CT_11 CC_10 CC_14 CT_12 CC_11 CT_10

CC_12 CT_11 CC_10

CT_12 CC_11 CT_10

CT_16

CT_15

S2/S3 S2/S3 20 21

CC_16

CC_15 23 24 25

CT_9 26

CT_8 27

CT_5 28

IN_COM

CC_Z 30

CT_6 31

CT_4 32

IN3

IN2

IN0

Q0B_1

Q0B_2

Q0A_1

Q0A_2

AC_Neutral /-

AC_Phase /+

CT_9 CT_8 CT_5

CC_Z CT_6 CT_4

IN0

CT_3

CT_1

CC_X

33 34 35 36

37 38 39 40 41 42 43 44 45 46 47 48

CT_6

CT_4

CC_Y

CT_2

CT_7 CT_7 CC_Y CC_Y CT_2 CT_2

IN1 Q0A_1 Q0A_1 Q0A_2 Q0A_2

CT_3 CT_3

IN4 Q0B_1 Q0B_1 Q0B_2 Q0B_2

CT_1 CT_1

IN5

PE PE

CC_X CC_X

IN6

CT_5

CC_Z

17 18 19 20

CT_7

13 14 15 16

CT_9

9 10 11 12

CT_8

CT_12

CC_12

CT_11

CC_11

CT_10

CC_10

49 - 50 51 52

53 54 55 56 57 58 59 60

AC_Neutral 61 62

AC_Phase

AC_Neutral

AC_Phase

Cable length maximum 50 m (164 ft)

DANGER

FIRE HAZARD

Use only the recommended wire sizes for I/O channels and power supplies.

Failure to follow these instructions will result in death or serious injury.

0.28

in.

AWG

Ø 3,5 mm (0.14 in.)

NHA45689 02 09 - 2016

0.2…2.5

24…14

0.2…2.5

24…14

0.25…2.5

23...14

0.25…2.5

23...14

N•m

lb-in

2 x 0.2…1

2 x 24…17

0.5...0.6

4.42...5.31

NOTICE

INOPERABLE EQUIPMENT

Do not tighten screw terminals beyond the specified maximum torque (Nm / lb-in.).

Failure to follow these instructions can result in equipment damage.

2 x 0.2…1.5

2 x 24…16

3/8

2 x 0.25…1

2 x 23…17

2 x 0.5...1.5

2 x 20...16

+ 5 hidden pages