All rights reserved, including translations into foreign languages. It is prohibited to copy, reproduce and distribute this docu-
ment or any excerpts thereof in any manner – including electronic means – without rst obtaining the publisher ’s written
consent. All of the information, technical data, pictures and illustrations in this manual are based on the most current data
available at the time of printing. Schaerer Ltd. reserves the right to make changes at any time without issuing a separate
notication. All pictures, illustrations and display messages in this manual serve only as examples. Due to a variety of possible options, your machine may differ from the devices shown in this manual. In the event, for any reason, of disaccord, the
German (DE) document shall be authoritative for Schaerer Ltd..
Observe the safety instructions and the chapter liability in the user manual
Schaerer Coffee Art, Schaerer Coffee Art Plus & Schaerer Coffee Vito!
User safety
DANGER!
Electrocution!
ATTENTION!
Health hazard!
ATTENTION!
Risk of burns!
● Only skilled electricians may carry out work on electrical systems!
The device must be connected to a secured circuit. (We recommend us- ●
ing an earth leakage circuit breaker in the connection).
All relevant guidelines on low voltage and/or country-specic or local ●
safety regulations and laws must be observed.
The connection must be grounded according to regulations and safe- ●
guarded against electrocution.
The voltage must correspond to the data on the device’s serial plate●● ●
Never insert the power plug into the socket while it is wet or touch it ●
with wet hands!
Never touch energized parts! ●
Before carrying out service work, always switch off the main switch ●
and/or disconnect the device from the power supply system.
The power cord may only be replaced by a qualied service technician. ●
Built-in safety devices must never be altered!●
● Children and persons under the inuence of alcohol, drugs or medica-
tion or those with physical, sensory or mental impairments may not use
the device except under supervision..
The coffee machine must be installed by the operator so that there are ●
no impediments to care and maintenance. In both self service and full
service applications, trained personnel must supervise the machine in
order to ensure that the care instructions are observed and personnel
are available for questions regarding use.
● Do not touch hot device components! The stainless steel shelves be-
come hot! The cup warmer has to cool down before cleaning!
Page 6
6 / 16 Operating instructions / V03 / 01.2010
Risk of damage to the machine
ATTENTION!
Risk of damage to
the machine
● The device must be set on a at, level and secure surface!
Do not expose the device to frost! This machine is not for outdoor use! ●
Do not spray the machine with water. The maximum relative humidity ●
should not exceed 80%; do not allow dewing.
For insurance reasons always ensure that, at the end of operation, the ●
mains power switch is switched off or the machine is unplugged!
Never spray the device with water or any other uid (e.g. steam clean- ●
er)!
Never immerse the device in water or in any other uid! ●
Maintenance work and repairs must only be performed by Schaerer Ltd. ●
service personnel using original spare parts!
We recommend damage prevention measures: – e.g. installing smoke ●
detectors.
If the coffee machine and/or auxiliary devices are transported at tem- ●
peratures below 10°C, the coffee machine and/or auxiliary devices must
remain for 3 hours at room temperature before being connected to a
power supply and switched on. If this recommendation is not observed,
there is a risk of short circuits or damage to the electrical components
as a result of condensation.
Page 7
Operating instructions / V03 / 01.20107 / 16
MAX.
OFF
1
FACTORY
SETTING
Operation
Cup warmer
Switch on the cup warmer
Plug in the mains plug. ►
Switch on the cup warmer using the ON/OFF switch ►
The switch lights up. The cup warmer is heated up after ± 60 minutes. ;
Adjust cup plate temperature
Mark the ground position of the switch on the backside of the machine! If the
temperature should be to high or to low, the switch can always be turned back to
its ground position.
Turn the adjustment screw clock wise on the backside of the machine. ►
The cup plate temperature increases. ;
Turn the adjustment screw counterclockwise wise on the backside of the ma- ►
chine.
The cup plate temperature decreases. ;
Filling the cup warmer
Carefully place the desired cups or pots with their openings downward in the ►
cup warmer.
1
.
Switch off the cup warmer
If this is not observed,
the warranty is invali-
dated in the event of
any resultant damage.
Switch off the cup warmer using the ON/OFF switch ►
The switch will no longer be illuminated. ;
► Remove the plug from the power supply.
1
.
Page 8
8 / 16 Operating instructions / V03 / 01.2010
MAX.
OFF
MAX.
1
OFF
FACTORY
SETTING
2
FACTORY
SETTING
Cup & Cool
Switch on the Cup & Cool
Plug in the mains plug. ►
Switch on the cup warmer using the ON/OFF switch ►
The switch lights up. The cup warmer is heated up after ± 60 minutes. ;
Switch on the refrigerator using the ON/OFF switch ►2 .
The switch lights up. After ± 60 minutes the refrigerator is on operating ;
temperature.
Adjust cup plate temperature
Mark the ground position of the switch on the backside of the machine! If the
temperature should be to high or to low, the switch can always be turned back to
its ground position.
Turn the adjustment screw clock wise on the backside of the machine. ►
The cup plate temperature increases. ;
Turn the adjustment screw counterclockwise wise on the backside of the ma- ►
chine.
The cup plate temperature decreases. ;
Adjust the refrigerator temperature
Mark the ground position of the switch on the backside of the machine! If the
temperature should be to high or to low, the switch can always be turned back to
its ground position.
Turn the adjustment screw clock wise on the backside of the machine. ►
The refrigerator temperature decreases. ;
Turn the adjustment screw counterclockwise wise on the backside of the ma- ►
chine.
The refrigerator temperature increases. ;
1
.
Filling the Cup & Cool
Carefully place the desired cups or pots with their openings downward in the ►
Cup & Cool.
Page 9
Operating instructions / V03 / 01.20109 / 16
Never top up milk
and always clean the
container thoroughly
before relling!
If this is not observed,
the warranty is invali-
dated in the event of
any resultant damage.
Fill the milk container
Open the refrigerator door. ►
Pull out the milk container. ►
Push the cover of the milk container back. ►
► Pour precooled milk (3 – 5°C) into the milk container.
Place the cover back on the container. ►
Push the milk container back in carefully. ►
Insert the adapter on the milk hose into the connection on the milk cover. ►
Close the refrigerator door. ►
Switch off the Cup & Cool
Switch off the cup warmer using the ON/OFF switch ►
The switch will no longer be illuminated. ;
Switch off the refrigerator using the ON/OFF switch ►
The switch will no longer be illuminated. ;
► Remove the plug from the power supply.
1
.
2
.
Page 10
10 / 16 Operating instructions / V03 / 01.2010
ATTENTION!
Risk of damage to
the machine!
ATTENTION!
Risk of damage to
the machine!
1
2
Change appliance fuse
Switch off the cup warmer / Cup & Cool using the ON/OFF switch(es) ►.
The switch(es) will no longer be illuminated. ;
R ► emove the plug from the power supply.
Cup warmer:
► Carefully lay the cup warmer on the side 1.
Cup & Cool:
► Carefully tilt the Cup & Cool until the fuse tray is accessible.
Remove the fuse tray ►2 using a screw driver.
Remove and replace the fuses ►3 (refer to technical data, page 13).
Place the fuse tray back in. ►
Carefully move the cup warmer / Cup & Cool back to its origin position. ►
► Plug in the mains plug.
3
Page 11
Operating instructions / V03 / 01.201011 / 16
ATTENTION!
Do not use any
abrasives!
ATTENTION!
The cup plates
become hot!
ATTENTION!
Do not use any
abrasives!
ATTENTION!
The cup plates
become hot!
Cleaning
Cup warmer
Cleaning the cup plates
Switch off the cup warmer using the ON/OFF switch ►
The switch will no longer be illuminated. ;
► Clean the cold device using a damp cloth. After wipe dry using a ne cloth or
chamois leather.
Cup & Cool
Cleaning the cup plates
Switch off the cup warmer using the ON/OFF switch ►
The switch will no longer be illuminated. ;
Switch off the refrigerator using the ON/OFF switch ►
The switch will no longer be illuminated. ;
► Clean the cold device using a damp cloth. After wipe dry using a ne cloth or
chamois leather.
1
.
1
.
2
.
Cleaning the milk container
The milk container
and milk hose must
be cleaned every
Do not kink the
day!
ATTENTION!
milk hose!
► Open the refrigerator door.
Unplug the milk hose with the milk nozzle and adapter from the milk container ►
cover.
Pull out the milk container and empty completely. ►Stir 5 ml of the Daypure (order no. 071300) from the measuring bottle into a ►
bucket containing 500 ml of warm water.
Use the cleaner solution to wipe out the milk container. ►
Wipe again using clean water. ►
Rub dry using a soft cloth. ►
► Re-plug the milk hose with the milk container and place the container back into
the refrigerator.
Close the refrigerator door. ►
Page 12
12 / 16 Operating instructions / V03 / 01.2010
ATTENTION!
Do not use any
abrasives!
Cleaning the refrigerator
► Open the refrigerator door and pull out the milk container.
Stir 5 ml of the Daypure (order no. 071300) from the measuring bottle into a ►
bucket containing 500 ml of warm water.
Use the cleaner solution to wipe out the inside of the refrigerator. Wipe again ►
using clean water.
Rub dry using a soft cloth. ►
Place the milk container back into the refrigerator. ►
Close the refrigerator door. ►
Defrosting the refrigerator
Defrost the refrigerator weekly, or as soon as the ice layer is thicker than 3 mm.
Never remove the ice layer with sharp or pointed objects. The surface of the cooling compartment can be damaged.
1
Switch off the refrigerator using the ON/OFF switch ►1 .
The switch will no longer be illuminated. ;
Leave the front door open. ►
Wipe away the water from melting ice with a soft cloth. ►
Close the front door before switching on again. ►
Page 13
Operating instructions / V03 / 01.201013 / 16
Technical data
We reserve the right to make technical
* For special models see model label, val-
ues given above are for the basic model.
modication!
Cup warmerCup & Cool
Power rating *210 W180 W
Mains connection
On-site power connection
On-site fuses1 x 10A
Appliance fuses2 x 2A (surge-proof)
Number of cup plates43
Cup capacity per cup plate
Shelf temperaturemax. 95°Cmax. 80°C
Milk capacity4 Liter
Width:
Height:
Depth:
Empty weight± 18.5 kg.± 27 kg.
1/N/PE | 50–60 Hz |
230 V
3 x 1,5² (earthed socket outlet)
Espresso
Ø 60mm
72364422
Coffee
Ø 90mm
1/N/PE | 50 Hz |
Espresso
Ø 60mm
272 mm
524 mm
385 mm
230 V
Coffee
Ø 90mm
Troubleshooting
ErrorRemedy
Refrigerator is iced up
The mains switch is not illuminated
The refrigerator is not
cooling
Cup(s) not getting warmRefer to “The mains switch is not illuminated”!
The cups are at a different temperature
Check: Is the door always closed? ●
Check: Is the seal OK? ●
Check: Is the cooling set too low? ●
Check: Switch on device? ●
Check: Is the mains plug plugged in? ●
Check: Is the local fuse defective? ●
Check: Is appliance fuse defective? ●
Refer to "The mains switch is not illuminated"!
Check: Not waited for the required cooling ●
time?
Check: Is the door seal defective? ●
Check: Has warm milk been poured in? ●
Check: Is appliance fuse defective? ●
The various containers require different heat- ●
ing times.
EN 60335-1: 2002 ●
EN 60335-1 /A1:2004 ●
EN 60335-1 /A2:2006 ●
EN 60335-1 /A11:2004 ●
EN 60335-1 /A12:2006 ●
EN 60335-1 /A13:2008 ●
EN 60335-2-49:2003-03 ●
EN 60335-2-49/A1:2008-09 ●
EN 60335-2-89:2002-12 ●
EN 60335-2-89/A1:2005-04 ●
EN 60335-2-89/A11:2004-07 ●
EN 60335-2-89/A2:2007-03 ●
EN 61000-6-3:2007-01: ●
EN 61000-3-2:2006-04 ●
EN 61000-4-3:2006-05 ●
EN 61000-4-4:2004-12 ●
EN 61000-4-5:2006-11 ●
EN 61000-4-11:2004-08 ●
EN 55022:2006-09 ●
The stated manufacturer declares herewith that this machine complies with all
relevant stipulations of the specied EU directives. In case of any modications of
the units that have not been approved by Schaerer, this declaration is rendered
invalid. A quality management system certied by Bureau Veritas, in accordance
with SN EN ISO 9001: 2008, has been used to ensure the proper adherence to