Sargent IN220,Sargent IN220 Installation Instructions Manual

IN220

PoE

Cylindrical Lock Installation Instructions

A8203A 04/16

Copyright 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.

Table of Contents

Warning ...................................................................................3

General Description .................................................................4

Speciﬁcations ..........................................................................4

System Overview .....................................................................4

Parts Breakdown .....................................................................5

Installation Wiring ...................................................................7

Lock Installation ....................................................................11

Operational Check ................................................................23

Warning

FCC:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Changes or modiﬁcations to this device not expressly approved by ASSA ABLOY could void the user’s authority to operate the equipment.

Industry Canada:

This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations.

Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Cet appareillage numérique de la classe B répond à toutes les exigences de l’interférence canadienne causant des règlements d’équipement. L’opération est sujette aux deux conditions suivantes: (1) ce dispositif peut ne pas causer l’interférence nocive, et (2) ce dispositif doit accepter n’importe quelle interférence reçue, y compris l’interférence qui peut causer l’opération peu désirée. “This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.”

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d’un type et d’un gain maximal (ou inférieur) approuvé pour l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l’intention des autres utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessaire à l’établissement d’une communication satisfaisante.

Any retroﬁt or other ﬁeld modiﬁcation to a ﬁre rated opening can potentially impact the ﬁre rating of the opening, and SARGENT Manufacturing makes no representations or warranties concerning what such impact may be in any speciﬁc situation. When retroﬁtting any portion of an existing ﬁre rated opening, or specifying and installing a new ﬁre-rated opening, please consult with a code specialist

or local code ofﬁcial (Authority Having Jurisdiction) to ensure compliance with all applicable codes and ratings.

To avoid possible damage from electrostatic discharge (ESD), some basic precautions should be used when handling electronic components:

• Minimize build-up of static by touching and/or maintaining contact with unpainted metal surfaces such as

Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.

door hinges, latches, and mounting plates especially when mounting electronic components such as readers and controllers onto the door

• Leave components (reader and controller) protected in their respective anti-static bags until ready for installation

• Do not touch pins, leads or solder connections on the circuit boards

02/28/16

1-800-810-WIRE • www.sargentlock.com • A8203A

IN220 Cylindrical Lock

General Description

The SARGENT IN220 Cylindrical lock combines superior aesthetics with the energy efﬁciency and streamlined architecture of Power-over-Ethernet (PoE) access control. PoE-enabled access control allows facilities to leverage existing network infrastructure for enhanced security and easier, more cost-effective installations. Featuring multiCLASS SE

technology, it supports multiple credential

types, including mobile devices, for a future-proof solution that is convenient and secure.

Hardware Specifications

• Complete lockset with on-board memory

• ADA compliant

• Easily retroﬁts existing (cylindrical lock) door preps

• Latch - 1/2” standard 3/4” throw ﬁre-rated double doors (optional) (41- preﬁx)

• Lock furnished for 1-3/4” doors. For other thicknesses, consult factory.

• May be used for indoor and outdoor applications

• ANSI/BHMA A156.25 Listed Grade 1 Compliant

• Outside lever controlled by contactless reader or mechanical cylinder

• Deadlocking latch - Stainless steel, non handed

NOTE: A weather-protective gasket is required for outdoor applications.

Electronic Specifications

• HID® multiCLASS SE® technology offers support for the following credentials:

• 2.4 GHz credential compatibility:

™

• Secure Identity Object Mobile IDs (Bluetooth Smart)

• 13.56 MHz credential compatibility:

• iCLASS®

• iCLASS SE® (SIO-enabled)

• iCLASS Seos

• SIO on MIFARE® Classic

• SIO on MIFARE® DESﬁre® EV1

• MIFARE® Classic

(SIO) on

• Input Power: PoE Class 1 Device, as deﬁned by IEEE 802.3af, requires less than 3.84 watts over structured cabling

• Multiple time zone and holiday access scheduling

• First-in unlock or automatic unlock conﬁguration, based on speciﬁed time schedule

• 2,400 users per lock; 10,000 event audit trail

• Privacy button

• Power Requirements: 55VDC, 90mA

• UL Listed* - UL 294 Indoor Use

• CUL Listed - S319: Class 1

• UL 294 Access Control Performance Ratings:

• DESﬁre® EV1

• NFC-enabled mobile phones

Destructive Attack Level I

Line Security Level I

• 125 kHz credential compatibilty:

• HID Prox

Endurance Level IV

Standby Power Level I

*UL testing was conducted on product powered by UL Listed model 9001GR/AC injector; manufactured by Microsemi Corp.

Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.

04/30/16

4 1-800-810-WIRE • www.sargentlock.com • A8203A

IN220 Cylindrical Lock

Parts Breakdown

PART NO./ORDER

ITEM

1 IN-220-EM01-[B*]IP-B Reader assembly - black plastic 1

STRING

IN-220-EM01-[B*]IP-W Reader assembly - white plastic

DESCRIPTION

QTY.

IN-220-EM01-[B*]IP-MB-xxx** Reader assembly - black plastic with metal trim

IN-220-EM01-[B*]IP-MW-xxx** Reader assembly - white plastic with metal trim

IN-220-EM01-[B*]IPS-B Reader assembly - black plastic

IN-220-EM01-[B*]IPS-W Reader assembly - white plastic

IN-220-EM01-[B*]CP-B Reader assembly - FeliCa - black plastic

IN-220-EM01-[B*]CP-W Reader assembly - FeliCa - white plastic

IN-220-EM01-[B*]CP-MB-xxx** Reader assembly - FeliCa - black plastic with metal trim

IN-220-EM01-[B*]CP-MW-xxx** Reader assembly - FeliCa - white plastic with metal trim

IN-220-EM01-[B*]IPS-MB-xxx** Reader assembly - black plastic with metal trim

IN-220-EM01-[B*]IPS-MW-xxx** Reader assembly - white plastic with metal trim

2 IN-220-EM04 Mounting plate assembly 1

2a Through-bolts (#8-32 x 1 1/4”) 2

3 IN-220-EM03 Controller assembly 1

4 IN-220-EM02-B Inside cover assembly - black plastic 1

IN-220-EM02-W Inside cover assembly - white plastic

IN-220-EM02-MB-xxx** Inside cover assembly - black plastic with metal trim

IN-220-EM02-MW-xxx** Inside cover assembly - white plastic with metal trim

*Specifying B indicates Bluetooth® Smart option when ordering

Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.

** Specify ﬁnish

04/30/16

5 1-800-810-WIRE • www.sargentlock.com • A8203A

Parts Breakdown (Continued)

IN220 Cylindrical Lock

PART NO./ORDER

ITEM

1 --- Outside Lever (Reference Catalog for Available Styles) 1

2 10-0043 Lever Retainer Key (In Screw Pack 10-2052) 1

3 --- Cylinder Assembly (Reference Catalog for Available Cylinders) 1

4 --- Rose (Reference Catalog for Avalable Styles) 2

5 10-0792 Spacer Bushing 2

6 10-3049 Outside Rose Spring Assembly 1

7 10-3407 Lock body Assembly 10G77 (Standard Cylinder) 1

8 10-0847 Adapter Plate/Spacer (Only Included With 1-3/8” Thick Doors) 1

9 10-3192 Latch Assembly 1

10 10-2052 Screw Pack 2

11 10-3048 Inside Rose Spring Assembly 1

12 --- Inside Lever (Reference Catalog for Available Styles) 1

13 52-5373 DPS (Door Position Switch) Kit 1

14 A8203A Instructions (this manual) 1

*Adapter Plate/Spacer (10-0847) is only shipped with orders that specify 1-3/8” doors.

Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.

STRING

10-3412 Lock body - LFIC

10-3417 Lock body - SFIC

DESCRIPTION

Tools Required:

• #2 Phillips screwdriver

• Flat head screwdriver

• Security allen wrench

QTY.

04/30/16

6 1-800-810-WIRE • www.sargentlock.com • A8203A

Installation Wiring

Overview

SARGENT IN220 PoE Typical Application

Network Switch (802.3af)

IN220 Cylindrical Lock

Network Cable

Surface Mount RJ45

LMT: Lock Management Tool

A. PoE frame harness assembly B. PoE data hinge from McKinney

(patent pending) C. PoE door harness* from McKinney D. IN220 PoE Lock E. DPS: Door Position Switch

(Needed on Cylindrical and Exits only) * Door width determines length

Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.

04/30/16

7 1-800-810-WIRE • www.sargentlock.com • A8203A

Installation Wiring (Continued)

IN220 Cylindrical Lock

Supplied by CI

Crimp Connector

Ceiling

24AWG

Stranded

Drain

Wire for

Earth

Ground in

15' Frame

Harness

Frame-Side

Harness

Assembly

(15' length)

Cable

drain wire concealed in shrink tubing

B-Splice

RJ45-M

24 AWG , 100ohm

Cable: Cat 5e or higher

Molex-M

Molex-F

Certiﬁed Integrator (CI) supplies and terminates

the B-Splice connector and the

male RJ45 connector from harness to

end user provided facility cable

To building or electrical ground

RJ45-F Jack

Cable: Cat 5e or higher

24 AWG

Cable: Cat 5e,

26 AWG stranded,

100ohm

Molex-F

Molex-M

Ring Terminal

Secured to Lock

Mounting Plate

Ground

RJ45-M

Patch Cable

Patch Panel to

PoE Switch

PoE

Lock

Supplied by End User

PoE Switch

PoE Switch is Terminated to Earth Ground

Patch Panel

Approved Software

Notes:

• Connectors go on only one way. They cannot be placed in an incorrect position.

• Do not force and do not offset connectors.

• Be sure they are completely seated (ﬂush).

• PoE power source cannot be connected to a receptacle controlled by a switch

Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.

04/30/16

8 1-800-810-WIRE • www.sargentlock.com • A8203A

Wiring to TIA/EIA 568-B Standard

+ 16 hidden pages

Sargent IN220,Sargent IN220 Installation Instructions Manual

Specifications and Main Features

Frequently Asked Questions

User Manual