Sargent IN120 Installation Instructions Manual

IN120

WiFi

Mortise Lock Installation Instructions

A8151D 03/15

Copyright 2015, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.

Table of Contents

Warning ...................................................................................2

General Description .................................................................3

Speciﬁcations ..........................................................................3

System Overview .....................................................................3

Parts Breakdown .....................................................................4

Lock Installation ......................................................................6

Operational Check ................................................................19

Warning

Changes or modiﬁcations to this device not expressly approved by ASSA ABLOY could void the user’s authority to operate the equipment.

FCC:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Industry Canada:

This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Cet appareillage numérique de la classe B répond à toutes les exigences de l’interférence canadienne causant des règlements d’équipement. L’opération est sujette aux deux conditions suivantes: (1) ce dispositif peut ne pas causer l’interférence nocive, et (2) ce dispositif doit accepter n’importe quelle interférence reçue, y compris l’interférence qui peut causer l’opération peu désirée. “This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.”

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d’un type et d’un gain maximal (ou inférieur) approuvé pour l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l’intention des autres utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessaire à l’établissement d’une communication satisfaisante.

Any retroﬁt or other ﬁeld modiﬁcation to a ﬁre rated opening can potentially impact the ﬁre rating of the opening, and SARGENT Manufacturing makes no representations or warranties concerning what such impact may be in any speciﬁc situation. When retroﬁtting any portion of an existing ﬁre rated opening, or specifying and installing a new ﬁre-rated opening, please consult with a

code specialist or local code ofﬁcial (Authority Having Jurisdiction) to ensure compliance with all applicable codes and ratings.

To avoid possible damage from electrostatic discharge (ESD), some basic precautions should be used when handling electronic components:

Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.

3/31/15

1-800-810-WIRE • www.sargentlock.com • A8151D

• Minimize build-up of static by touching and/or maintaining contact with unpainted metal surfaces such as door hinges, latches, and mounting plates especially when mounting electronic components such as readers and controllers onto the door.

• Leave components (reader and controller) protected in their respective anti-static bags until ready for installation

• Do not touch pins, leads or solder connections on the circuit boards

IN120 Mortise Lock

General Description

The IN120 WiFi lock offers the ease and ﬂexibility of WiFi in a streamlined design, setting a new standard for aesthetics and performance. The IN120 uses IEEE 802.11 WiFi communication and a ﬂexible feature set for easier, more cost-effective installations, allowing facilities to leverage their IT infrastructure to expand access control coverage to more doors. Featuring HID® multiCLASS SE® technology, it supports heightened identity security and multiple credentials, including NFC-enabled mobile phones.

This product is operated by six (6) “AA” alkaline batteries, or can be hard-powered using an optional 12-24VDC power supply connected by a harness through the door. SARGENT mortise locks are designed with quality components to provide high security, performance and durability.

Hardware Specifications

• Complete lockset with on-board memory

• ADA compliant

• Easily retroﬁts existing door preps (mortise)

• Latch - Stainless steel

• Optional deadbolt - Hardened steel

• Guardbolt - Stainless steel, non handed

• Handing (RH/RHR/LH/LHR) must be speciﬁed, but is easily ﬁeld-reversible without opening the lock case

Electronic Specifications

• Input Power: DC 9V, 1.5A (6 AA alkaline batteries)

• Optional hard-power 12VDC to 24VDC

• HID® multiCLASS SE® technology offers support for the following credentials:

• High Frequency (13.56 MHz):

• HID iCLASS

• HID iCLASS SE® (SIO-enabled)

• HID iCLASS

• HID MIFARE® SE

• HID DESﬁre® EV1 SE

• MIFARE Classic

• DESﬁre EV1

• FeliCa

• Low Frequency (125 kHz):

• HID Prox

Seos

™

• Case - 12 gauge heavy duty wrought steel

• Cylinder retracts latchbolt (and deadbolt)

• Inside lever retracts latch and deadbolt simultaneously

• Lock furnished for 1-3/4” doors. For other thicknesses, consult factory.

• UL Listed (3 hr.)

• Outside lever controlled by any combination of contactless reader or mechanical cylinder

• WiFi (IEEE 802.11 b/g/n)

• Multiple time zone and holiday access scheduling

• First-in unlock or automatic unlock conﬁguration, based on speciﬁed time schedule

• Support for most advanced wireless encryption and authentication standards such as WEP, WPA, WPA2 and 802.1x*

• 2,400 users per lock; 10,000 event audit trail

• Privacy button

• 8200 lock body offers monitoring of deadbolt REX

and provides integrated monitoring of door position

*For speciﬁc security information, please contact your local ASSA ABLOY Door Security Solutions sales consultant or call 800-810-WIRE.

To comply with “Fire Listed” doors, the batteries must be replaced with alkaline batteries only.

1-800-810-WIRE • www.sargentlock.com • A8151D 3

Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.

3/31/15

IN120 Mortise Lock

Parts Breakdown

PART NO./ORDER

ITEM

1 IN-EM01-IPS-B Reader assembly - black plastic 1

2 IN-120-EM04 Mounting plate assembly 1

2a Through-bolts (#8-32 x 1 1/4”) 2

3 IN-120-EM03 Controller assembly 1

4 N/A AA battery 6

5 IN-EM02-B Battery cover assembly - black plastic 1

STRING

IN-EM01-IPS-W Reader assembly - white plastic

IN-EM01-CP-B Reader assembly - FeliCa - black plastic

IN-EM01-CP-W Reader assembly - FeliCa - white plastic

IN-EM01-IPS-MB-xx* Reader assembly - black metal

IN-EM01-IPS-MW-xx* Reader assembly - white metal

IN-EM01-CP-MB-xx* Reader assembly - FeliCa - black metal

IN-EM01-CP-MW-xx* Reader assembly - FeliCa - white metal

IN-EM02-W Battery cover assembly - white plastic

IN-EM02-MB-xx* Battery cover assembly - black metal

IN-EM02-MW-xx* Battery cover assembly - white metal

* Specify ﬁnish

DESCRIPTION

QTY.

Tools Required:

• #2 Phillips screwdriver

• Flat head

• T20 Torx® driver

• Security allen wrench (provided)

Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.

3/31/15

4 1-800-810-WIRE • www.sargentlock.com • A8151D

IN120 Mortise Lock

Parts Breakdown (Continued)

ITEM

1 Consult Factory #41 Mortise cylinder 1

2 13-2131 97 Ring 1

3 IN-120-7976-hand-ﬁn Lock body with deadbolt with cylinder 1

4 77-4081 130W Turn lever 1

5 79-2162 Trim pack 1

6 Consult Factory Rose

7 Consult Factory Inside lever 1

8 79-0035 Without deadbolt 1

9 52-5373 Door Position Switch (DPS) pack 1

10 77-4236 Mortise screw pack - specify ﬁnish (includes: wood and metal lock

11 Consult Factory Outside trim 1

12 A8150 Field prep template (not shown) 1

13 4713 Door manufacturers template (not shown) 1

14 A8151 Instructions (this manual) 1

STRING

IN-120-7977-hand-ﬁn Lock body with deadbolt without cylinder

IN-120-7978-hand-ﬁn Lock body without deadbolt with cylinder

IN-120-7979-hand-ﬁn Lock body without deadbolt without cylinder

IN-120-82276-hand-ﬁn* Lock body with deadbolt with cylinder (not shown)

IN-120-82277-hand-ﬁn* Lock body with deadbolt without cylinder (not shown)

IN-120-82278-hand-ﬁn Lock body without deadbolt with cylinder (not shown)

IN-120-82279-hand-ﬁn Lock body without deadbolt without cylinder (not shown)

79-0036 With deadbolt (shown)

body screws, faceplate screws, and strike screws)

PART NO/ORDER

DESCRIPTION

QTY

Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.

*Required for Escape Return functionality (a residential requirement in Canada)

1-800-810-WIRE • www.sargentlock.com • A8151D 5

3/31/15

Lock Installation

1 Prepare Door

A. Verify Hand and Bevel of Door

Stand on outside of locked door when determining door hand.

IN120 Mortise Lock

Left Hand

Hinges Left

Open Inward

B. Door Preparation

Prior to installation, all holes must be free of burrs, debris and sharp edges.

Prepare door according to appropriate template (see website www.intelligentopenings.com).

• Field Template: A8150 (ships with product)

• Door Manufacturer’s Template: 4713

Cable Hole

Outside Cylinder Hole

(only with cylinder

installation)

LHRB

Left Hand

Reverse Bevel

Hinges Left

Open Outward

Fig. 1A

Outside of Door Inside of Door

Through-bolt Hole

External DPS

Hole

Through-bolt Hole

Right Hand Hinges Right Open Inward

RHRB

Right Hand

Reverse Bevel

Hinges Right

Open Outward

Cable Hole

Inside of Lock body Wire Hole

Thumb Turn Lever Hole

Lever Holes

Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.

3/31/15

6 1-800-810-WIRE • www.sargentlock.com • A8151D

Mortised

Fig. 1B

Pocket

Lever Holes

+ 14 hidden pages

Sargent IN120 Installation Instructions Manual

Specifications and Main Features

Frequently Asked Questions

User Manual