Sanyo DTA-120 Instruction Manual
INSTRUCTIONS MANUAL
Audio System
DTA-120
-11-
PRECAUTIONS
CAUTION
THIS PRODUCT CONTAINS A LOW POWER LASER DEVICE, TO
ENSURE CONTINUED SAFETY DO NOT REMOVE ANY COVERS
OR A TTEMPT TO GAIN ACCESS TO THE INSIDE OF THE PRODUCT.
REFER ALL SERVICING TO QUALIFIED PERSONNEL.
CLASS 1 LASER PRODUCT
LUOKAN 1 LASERLAITE
KLASS 1 LASERAPPARAT
- The apparatus shall not be exposed to dripping or splashing.
- Do not use where there are extremes of temperature (below 5°C or
exceeding 35°C) or where direct sunlight may strike it.
- Because of the CD player’s extremely low noise and wide dynamic
range, there might be a tendency to set the volume on the amplifier
unnecessarily high. Doing so may produce an excessively large
output from the amplifier which could damage your speakers.
IMPORTANT
If the plug supplied with this equipment is not suitable for the socket
outlets in your home it should be cut off and replaced with the correct
type.
Disposal of Plug
If the non rewireable plug is to be cut off, the removed plug should be
disposed of carefully as there is a shock hazard should the plug be
inserted into a live socket.
Replacing Fuse
The detachable fuse cover must be replaced after changing the fuse.
Only a 3A fuse should be used and should comply with BS1362 and
should carry the ASTA mark .
- Sudden changes in the ambient temperature may cause condensation to form on the optical lens inside the unit. If this happens, take out
the disc, leave the unit for about 1 hour, and then proceed to operate.
- The system’s speakers use powerful magnets. Do not place timepieces,
credit cards, cassette tapes or video tapes, etc. near the speakers.
- Do not install this equipment in a confined space, such as a book case
or built in cabinet.
- No object filled with liquids, such as vase, shall be placed on the
apparatus.
The wires in the mains lead are coloured in accordance with the following code;
Blue Neutral
Brown Live
The wires in the mains lead must be connected to the terminals in the
plug as follows;
Wire colour Plug terminal marking
Blue N or Black or Blue
Brown L or Red or Brown
Do not connect either wire to the earth terminal.
If the mains plug contains a fuse this should be 3A, if a plug without a
fuse is used the distribution board fuse should not be greater than 5A.
The unit is not disconnected from the mains unless it is unplugged from the AC outlet
-1-
FM ANT.
Stereo headphones
(not supplied)
CONNECTIONS
VIDEO equipment
Note:
- Do not connect the AC adaptor to an AC outlet until all connections
have been made.
POWER SUPPLY
Plug one end of the AC adaptor into the EXT. DC socket, then plug the
other end into an AC outlet.
- Use only the supplied AC adaptor.
- The system is not completely disconnected from the mains when
the z/ON button is set to the z position.
Video equipment
Connect audio leads (not supplied) from an audio output sockets of a
video equipment to the LINE IN sockets.
Headphones
Connect stereo headphones (not supplied) to the PHONES socket for
monitoring or for private listening. The speakers are automatically disconnected when headphones are connected.
Speaker
Connect the speaker wire to the speaks “L” and “R” socket.
You can open the back door of the speakers and pull the seakers wire
out to make a preparation for detach them.
-2-
Detach the speakers
1. Push the left and right slide slices (at the bottom) towards the unit.
2. Pull the speakers upwards to seperate from the main unit.
Attach the speakers
1. Put the speakers downwards to mount at the side of the main unit.
2. Push the slide slices to the speakers.
To hang the speakers and/or main unit on the wall
You can hang up the speaker and/or main unit through the water-drop
style holes at the back of the unit (speakers) on the wall where there
was proper nails or hooks.
• For a perfect amount effect, you had better detach the sustain foot of the unit first.
-3-
Loading...