Sanyo DSP10 Specifications

SANYO Electric Co.,Ltd. Semiconductor Company

TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN

Ordering number : ENN6512

DSP10

Silicon Diffused Junction Type

DSP10

Power Rectifier

Features

•

Facilitates automatic mounting and
miniaturization in end products.

• Peak reverse voltage : V

• Average rectified current : I

Specifications

RM

=600V.

=1.0A.

O

Package Dimensions

unit : mm

1300

1.0

0.5

[DSP10]

1.8

1.4

1.0

2.8

Cathode mark

3.9

1.0

1.0

1.8

SANYO : SHP

Absolute Maximum Ratings at Ta=25°C

Peak Reverse Voltage V
Average Rectified Current I

Surge Forward Current I

Junction T emperature Tj 150 °C
Storage T emperature T stg --55 to +150 °C

Parameter Symbol Conditions Ratings Unit

RM

50Hz sine wave, mounted on an alumina board 1.0 A

O

Load resistor (solder pad size 4mm2✕20µmt)
Mounted PCB 0.64 A
Load resistor (solder pad size 4mm2✕20µmt)
Mounted PCB 0.80 A
Load resistor (solder pad size 4mm2✕20µmt)

FSM

50Hz sine wave 25 A
non-repetitive, 1cycle peak value

600 V

Electrical Characteristics at Ta=25°C

Parameter Symbol Conditions min typ max Unit
Forward Voltage V
Reverse Current I
Thremal Resistance θi-l Junction-Lead 20 °C/W

F

R

θi-a Junction-Ambient, mounted on an 108 °C/W

IF=1.0A 1.1 V
VR=V

RM

alumina board
(solder pad size 4mm2✕20µmt)
Mounted on PCB 186 °C/W
(solder pad size 4mm2✕35µmt)
Mounted on PCB 142 °C/W
(solder pad size 16mm

2

✕35µmt)

10 µA

Any and all SANYO products described or contained herein do not have specifications that can handle
applications that require extremely high levels of reliability, such as life-support systems, aircraft's
control systems, or other applications whose failure can be reasonably expected to result in serious
physical and/or material damage. Consult with your SANYO representative nearest you before using
any SANYO products described or contained herein in such applications.

SANYO assumes no responsibility for equipment failures that result from using products at values that
exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other
parameters) listed in products specifications of any and all SANYO products described or contained
herein.

40700 GI IM

No.6512-1/2

10

7
5

3

-- A

2

F

1.0
7
5

3

Forward Current, I

2

I

Ta=150°C

F

-- V

25°C

DSP10

I

F

1.2

1.0

-- A

Alumina board

O

0.8

PCB board 1

PCB board 2

0.6

0.4

0.2

Average Rectified Current, I

O

-- Ta

When mounted on
an alumina board.

Solder pad size 2mm
PCB board 1
Solder pad size 4mm
PCB board 2
Solder pad size 2mm

Sine wave
Load resistor

0.1

0.6 0.8 1.00.4

Forward Voltage, V

50

40

-- A

FSM

30

20

10

Surge Foward Current, I

0

1.0 10

2

357 2357

Number of Cycles at 50Hz, n

Specifications of any and all SANYO products described or contained herein stipulate the performance,
characteristics, and functions of the described products in the independent state, and are not guarantees
of the performance, characteristics, and functions of the described products as mounted in the customer’s
products or equipment. To verify symptoms and states that cannot be evaluated in an independent device,
the customer should always evaluate and test devices mounted in the customer’s products or equipment.

SANYO Electric Co., Ltd. strives to supply high-quality high-reliability products. However, any and all
semiconductor products fail with some probability. It is possible that these probabilistic failures could
give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire,
or that could cause damage to other property. When designing equipment, adopt safety measures so
that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective
circuits and error prevention circuits for safe design, redundant design, and structural design.

In the event that any or all SANYO products(including technical data,services) described or
contained herein are controlled under any of applicable local export control laws and regulations,
such products must not be exported without obtaining the export license from the authorities
concerned in accordance with the above law.

No part of this publication may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying and recording, or any information storage or retrieval system,
or otherwise, without the prior written permission of SANYO Electric Co. , Ltd.

Any and all information described or contained herein are subject to change without notice due to
product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification"
for the SANYO product that you intend to use.

Information (including circuit diagrams and circuit parameters) herein is for example only ; it is not
guaranteed for volume production. SANYO believes information herein is accurate and reliable, but
no guarantees are made or implied regarding its use or any infringements of intellectual property rights
or other rights of third parties.

I

FSM

-- n

50Hz

F

-- V

IT02088

IT02090

1.81.2 1.4 1.6

100

0

0

Ambient Temperature, Ta -- °C

16020 40 60 80 100 120 140

IT02089

This catalog provides information as of April, 2000. Specifications and information herein are subject to
change without notice.

No.6512-2/2

PS