Sanyo DP42851 User Manual
2
Need help? www.sanyoctv.com 1-800-877-5032
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding-type plug has two
blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. If the provided
plug does not fit fully into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the
manufacturer.
12. Use only with the cart, stand, tripod,
bracket, or table specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination
to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when
unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects have
fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally,
or has been dropped.
15. If an outside antenna is connected to the television
equipment, be sure the antenna system is grounded so
as to provide some protection against voltage surges
and built up static charges. In the U.S. Selection 810-21
of the National Electrical Code provides information with
respect to proper grounding of the mast and supporting
structure, grounding of the lead-in wire to an antenna
discharge unit, size of grounding conductors, location of
antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrodes.
16. An outside antenna system should not be located in the
vicinity of overhead power lines or other electrical light
or power circuits, or where it can fall into such power
lines or circuits. When installing an outside antenna
system, extreme care should be taken to keep from
touching such power lines or circuits as contact with
them might be fatal.
EXAMPLE OF ANTENNA GROUNDING ACCORDING
TO NATIONAL ELECTRICAL CODE, ANSI/NFPA 70
“Note to CATV system installer:
This reminder is provided to call the CATV system installer’s
attention to Article 820-40 of the NEC that provides guidelines for
proper grounding and, in particular, specifies that the cable
ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.”
17. Wall or Ceiling Mounting—The product should be
mounted to a wall or ceiling only as recommended by
the manufacturer.
18. Apparatus shall not be exposed to dripping or splashing
and no objects filled with liquids, such as vases, shall be
placed on the apparatus.
19. When the MAINS plug is used as the disconnect device,
the disconnect device shall remain readily operable.
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN!
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A
RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT.
THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND
MAINTENANCE INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THIS
UNIT.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE.
IMPORTANT SAFETY INSTRUCTIONS
3
Need help? www.sanyoctv.com 1-800-877-5032
PC RESOLUTION CHART
FCC INFORMATION __________
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or
more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
CAUTION: FCC Regulations state that improper modifications or
unauthorized changes to this unit may void the user’s authority to
operate the unit.
As an Energy Star
®
Partner, Sanyo
Manufacturing Corporation has
determined that this product meets
the Energy Star
®
guidelines for energy
efficiency.
HDMI, the HDMI Logo and HighDefinition Multimedia Interface are
trademarks or registered trademarks of
HDMI Licensing LLC in the United
States and other countries.
This Class B digital apparatus complies with Canadian
ICES-003.
Manufactured under license from
Audyssey Laboratories. U.S. and
foreign patents pending. Audyssey
Dynamic Volume
®
is a registered
trademark of Audyssey Laboratories.
SPECIFICATIONS
Power Requirement: Source: AC 120V, 60Hz
AC Power Consumption: 126 watts
Weight: 33 lbs.
Dimensions:
MODEL WIDTH HEIGHT DEPTH
DP42851 40.0 26.4 9.2
w/o stand 40.0 24.4 4.0
NOTE: Dimensions are in inches
Adobe
®
, Adobe Flash®, and Flash
Lite®are either registered trademarks
or trademarks of Adobe Systems
Incorporated in the United States
and/or other countries.
TRADEMARKS
Manufactured under license from
Dolby Laboratories. Dolby and the
double-D symbol are trademarks of
Dolby Laboratories.
4
Need help? www.sanyoctv.com 1-800-877-5032
CONTENTS
IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . 2
FCC INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
TRADEMARKS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
PC RESOLUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
PROTECTING THE LCD SCREEN . . . . . . . . . . . . . . . . . . . . .4
HANDLING PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . .4
POSITIONING THE LCD HDTV . . . . . . . . . . . . . . . . . . . . . . .4
STAND ASSEMBLY / WALL MOUNTING . . . . . . . . . . . . . 5
GETTING STARTED—
Remote Control Battery Installation . . . . . . . . . . . . . . . .5
Antenna Connections for off-air or cable . . . . . . . . . . .5
BACK PANEL JACKS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
A/V CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
REMOTE CONTROL OPERATION . . . . . . . . . . . . . . . . . . . . .8
POWER CONNECTION / INITIAL CHANNEL SEARCH . . .9
ON-SCREEN MENU OPERATION—
Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Menu Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Digital Caption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Clock Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
AV Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
- Video 2 Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
- HDMI CEC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
No Signal Shut-off . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Mode (Home/Store) . . . . . . . . . . . . . . . . . . . . . . . . . .10
Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
V-Chip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Channel Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Channel Scan Memory . . . . . . . . . . . . . . . . . . . . . . .11
Picture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Manual Picture Settings . . . . . . . . . . . . . . . . . . . . . .12
Energy Saver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Light Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
H-Size and V-Size . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Pix-Size Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
aaManual Sound Settings . . . . . . . . . . . . . . . . . . . .13
3D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
PHOTO/VIDEO VIEWER . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
PC CONNECTIONS AND SETTINGS . . . . . . . . . . . . . . . . .16
WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
GNU GENERAL PUBLIC LICENSE . . . . . . . . . . . . . . . . . . .19
POSITIONING THE HDTV
•
Always use a firm and flat surface when positioning
your HDTV.
•
Do not position the unit in a confined area.
•
Allow adequate space for proper ventilation.
•
Do not position the HDTV where it is easily reachable
by small children and may present risk of injury.
•
Once HDTV is positioned, remove the protective film
covering the front cabinet.
NOTE: Button area on bottom right hand corner will be
more accessible once film is removed.
“The American Academy of Pediatrics discourages
television viewing for children younger than two years
of age”
PROTECTING THE LCD SCREEN
CAUTION: The screen can be damaged if it is not
maintained properly.
•
Do not use hard objects such as hard cloth or paper to
clean the screen.
•
Do not use excessive pressure when cleaning the
screen; excessive pressure can cause permanent
discoloration or dark spots.
•
NEVER spray liquids on the screen.
•
The use of a damp microfiber cloth is recommended.
HANDLING PRECAUTIONS
•
Handle by the cabinet only.
•
Handling by two or more people is recommended.
•
Never touch the screen when handling.
•
Handling damage is not covered under warranty.
•
Do not remove the protective film covering the front
cabinet while handling the HDTV.
Please read before
operating your HDTV!
CONTAINS MERCURY LAMPS,
DISPOSE OF PROPERLY
RECYCLING OF SANYO TELEVISIONS:
SANYO television customers should contact
MRM Recycling at 888-769-0149 or visit their
website at www.mrmrecycling.com regarding
SANYO’s waste management plan.
5
Need help? www.sanyoctv.com 1-800-877-5032
Hook up your antenna or your cable service to the
HDTV’s ANT terminal with the use of a 75 OHM
coaxial cable.
NOTE: Keep your indoor antenna at least 3 ft. away
from the television set and any other electronic
equipment.
The tuner in this HDTV can receive:
•
Digital and Analog off air signals from an antenna
• Analog or ClearQAM cable channels from a direct
Cable TV connection.
GETTING STARTED
Install two (2) “AA” batteries in the remote control.
(Not included)
To ensure safe operation, please observe
the following precautions:
• Replace both batteries at the same time. Do not use
a new battery with a used battery.
• There’s a risk of explosion if a battery is replaced
by an incorrect type.
• Do not expose the Remote Control unit to moisture
or heat.
• Be sure to match the “+” and “–” signs on the
batteries with marks inside the remote control.
ANTENNA CONNECTION FOR
OFF-AIR SIGNALS OR CABLE
ANTENNA
CABLE
ANALOG / DIGITAL
ANTENNA IN
BATTERY INSTALLATION
Wall mounting of the HDTV must be performed
by a skilled person.
If stand base disassembly is required:
1
Place HDTV face down
on a padded or cushioned
flat surface to protect the screen and finish.
2
Remove the four (4) screws securing the foot stand.
CAUTION: Hold the stand firmly as you remove the
last screw.
Use the screws you would use to attach the stand base
to secure the HDTV to a wall mounting kit.
NOTE: Wall mounting kit is not included.
VESA standard interface: 400 x 400
Mounting screws measurements:
M6 (6mm) Diameter, Length—12mm (maximum)
WALL MOUNTING (OPTIONAL)
Wall Mounting
Inserts
NOTE: Skip these steps if you are wall mounting the TV.
1
Place HDTV face down on a padded or cushioned
flat surface to protect the screen and finish.
2
Carefully insert the stand base to the bottom of the
HDTV and secure the base by inserting 4 screws as
indicated in the diagram below.
NOTE: Stand base screws are located in the literature
package.
3
Position the HDTV on a firm and flat surface with
adequate space for proper ventilation.
STAND ASSEMBLY ___________
6
Need help? www.sanyoctv.com 1-800-877-5032
GETTING STARTED
HDTV INPUT/OUTPUT REFERENCE
HDTV BACK PANEL
6
3
4
USB Input
View pictures or video files stored in a USB flash drive.
ETHERNET port
Hook up your HDTV to the internet with the use of an appropriate ethernet cable and a correct internet setup.
NOTE: Please refer to the Internet Ready HDTV Guide for the
proper connection methods.
HDMI (INPUT1, INPUT2, & INPUT3)
An all digital Audio/Video interface that can accept uncompressed video signals up to 1080p for the very best picture
possible with the use of a single HDMI cable.
NOTE: A DVI connection is possible via the HDMI (DVI) INPUT1
using an appropriate adapter and connecting the audio to
the stereo mini AUDIO jack.
PC Input
Monitor RGB (D-SUB)
AUDIO mini stereo jack (3.5mm)
For AUDIO signal from PC or DVI device.
Analog / Digital Antenna Input
Component AV Input (VIDEO2 or VIDEO3)
Green (Y), blue (Pb), and red (Pr) Video inputs plus the white
and red Audio inputs.
NOTE: A composite connection is possible via VIDEO INPUT2
using the Y (VIDEO) jack and the L/R audio jacks. (See
Video2 Setting on page 10.)
Composite AV Input (VIDEO1)
Yellow (Video), plus white and red (Audio) input jacks.
Digital Audio Output (Coaxial)
Analog Stereo Audio Out (L/R) Jacks
1
2
3
4
5
6
7
8
Composite
Component
NOTE: Composite, Component, and DVI video connections need their appropriate audio connections.
High Definition image available from HD signals and HD equipment.
Standard Definition
High Definition
Optimum
High Definition
H D M I
(or DVI to HDMI
cable/adapter)
8
7
1
5
9
10
9
2
10
7
Need help? www.sanyoctv.com 1-800-877-5032
GETTING STARTED
AUDIO / VIDEO CONNECTIONS
DVD PLAYER
(or similar device)
VCR
(or analog device)
MULTICHANNEL
RECEIVER
NOTE: Audio/Video cables
are not supplied
Component connections will accept SDTV,
EDTV and HDTV video signals. Use them
for great image quality from digital
devices.
NOTE: Always match the color of your
device’s output jack, the connector
and the HDTV’s input jack.
SATELLITE RECEIVER
(or similar device)
USB FLASH
DRIVE
HDMI (DVI) INPUT1 can be used to
hookup a DVI device with the use of an
appropriate DVI to HDMI cable or adapter.
(AUDIO DVI jack needs to be hooked up to
the DVI device as well.)
NOTE: HDMI INPUT1 may also be used to
hookup any digital device with an
HDMI output, without the use of
the AUDIO (DVI) jack.
USB input jack is used to connect a USB mass
storage device (not included) to display digital images or
video files on your HDTV.
DVI
HDMI INPUT1, 2 & 3 are used to hookup HD digital
devices such as a Blu-ray player, HD Cable Box, HD
Satellite Receiver or Video-game System.
Connect your digital device’s HDMI output to any of
the three (3) HDMI inputs on your HDTV with the use
of an HDMI cable.
Audio Output L/R jacks are used to
hookup an external stereo Amplifier.
(Do not connect external speakers
directly to the HDTV.)
STEREO
AMPLIFIER
Composite connections are used to hookup analog
equipment such as a VCR or an older DVD player.
NOTE: Always match the color of your device’s
output jack, the connector, and the HDTV’s
input jack.
Digital Audio Output is used to
hookup a multichannel receiver
with the use of a phono-type digital
audio cable.
DVD PLAYER
(or similar device)
8
Need help? www.sanyoctv.com 1-800-877-5032
REMOTE CONTROL OPERATION
Selects the video source to view.
Turns your HDTV On or Off.
Switch viewing mode between 2D and 3D.
Pressing it twice restores your HDTV to
its factory settings. All user customized
settings will be cleared.
Cycles through the available aspect
ratios. The different settings either
stretch, zoom, or fill the image on your
screen. Bars may appear on top and bottom of your screen (or on left and right
sides) depending on the broadcasted signal or program. (See page 13)
Cycles through the available Caption
modes (when available.)
Allows for the direct selection of digital
subchannels. For example: to select
channel 39.1 press the 3 and 9 keys,
followed by the dash ––, and 1 keys.
Increases or decreases the audio level.
Select channels directly.
For channels 100 and up, press and hold
the first number, then enter the remaining
two numbers.
Switch between current channel and last
selected channel or input.
Displays or hides the on-screen menu.
Scan through the channels in the memory
database.
Move the on-screen cursor in the
desired direction, press the ENTER key
to select highlighted options.
Operate playback functions when viewing
video files from a USB flash drive or from
an internet application.
Displays on-screen Help menu.
Access the VUDU app directly.
(Internet access requiered.)
Exits the on-screen menu.
Mute or restore the sound.
Use the on-screen QUIK menu to access
Video and Sound modes directly, or the
AUDIO (stereo, mono, SAP) and Sleep
Timer features.
Opens the Sanyo Net Apps menu screen.
9
Need help? www.sanyoctv.com 1-800-877-5032
1. PLUG IN AC POWER CORD
120V AC, 60Hz
2. TURN ON TV (PRESS POWER BUTTON)
Wait for on-screen instructions to set an Initial Energy
Saving Mode, and perform an Initial Channel/Signal
Search.
3. TV SET LOCATION SELECTION:
Select “Home Mode” to set the HDTV’s backlight to
an Energy Star qualified level, or select “Store
Mode”to set the backlight to a retail display level.
Press ENTER on the desired option to continue.
4. CHANNEL AND AV SIGNAL SEARCH:
Select the Signal Search option and press ENTER to
perform a channel search from an Antenna or a direct
Cable connection, and a signal search from devices
hooked up to the HDTV’s AV input jacks.
5. CHANNEL AND SIGNAL SETUP SCREEN
The final setup screen displays analog and digital
channels found as well as AV inputs detected.
Select Finish Setup and press ENTER to go to one of
your HDTV’s inputs.
NOTE: If you wish to repeat the Signal Search
process select Repeat.
GETTING STARTED
INITIAL CHANNEL SEARCH
Before proceeding, please make sure to hook up
your antenna or cable connection and all AV
equipment correctly to your HDTV.
AV INPUT SELECTION
Press the INPUT key to select the correct AV input for the
video source you wish to watch.
NOTE: Unused AV inputs may be disabled with the Skip
Setting feature (see INPUTS.)
INPUTS ___________________________
ON-SCREEN MENU OPERATION
Choose between English, Spanish and French for your
On Screen menu’s display language.
Press ENTER on the desired language.
Menu Language
SETUP
_______________________
Captioning is textual information transmitted along with
the picture and sound. Turning Captioning ON (by
pressing the CAPTION key during normal TV viewing)
causes the HDTV to open these captions (digital or analog) and superimpose them on the screen.
NOTE: Local broadcasters decide which caption signals
to transmit.
Use the CURSOR and keys to modify Font,
Background, and Foreground of digital caption text.
Display the On Screen menu and use the CURSOR
keys to select Setup. Press ENTER.
Digital Caption
Display the On Screen menu and use the CURSOR
keys to select Inputs. Press ENTER.
Inputs allows the direct selection of any AV input and
the removal of unused inputs from the AV input loop.
Use the CURSOR keys to select the desired AV input
and press ENTER.
To manage the available inputs press the 1 key to enter
the Skip Setting screen. Use the CURSOR keys to
select an AV input and press ENTER to disable
(uncheck) or enable (check) the highlighted input.
10
Need help? www.sanyoctv.com 1-800-877-5032
Video 2 Setting - Use this feature to establish either
a Component or Composite connection to the VIDEO
INPUT 2 jacks on your HDTV.
Use the CURSOR keys to select the type of connection you’ll use in VIDEO INPUT 2.
Press ENTER, a blue mark will appear next to the selected option indicating it is the active option.
HDMI CEC - Use the HDMI-CEC Function to enable or
disable all available CEC functions.
HDMI Power ON Sync and Power OFF Sync enable
specific features including the automatic power ON
process and power OFF process.
This feature allows you to set a Current Time for your
HDTV and enable a Switch On Time for the HDTV to
turn on at a specific time of day.
When On Timer Function is set to ON, the TV will
automatically turn on at the previously set Switch on
Time.
Clock timer
SETUP
(CONTINUED) __________________
ON-SCREEN MENU OPERATION
AV Connections
Use this feature to automatically block programs with
content you deem inappropriate for viewing by children.
NOTE: This feature is designed to comply with the
United States of America’s FCC V-Chip regulations. Therefore, it may not function with broadcasts that originate in other countries.
ADJUSTING THE V-CHIP RATINGS
Select ON and press ENTER. Select Adjust (Standard)
and press ENTER.
NOTE: Blocking a rating will automatically block all
higher ratings. Unblocking a rating will automatically unblock all lower ratings.
V-Chip (parental control)
When No Signal Shut-off feature is set to ON, it will
allow the HDTV to automatically turn off when no
video and/or audio signals are being received.
NOTES: By factory default, this feature is set to ON.
TV will automatically turn off if no AV signals
are received in a time span of 15 minutes.
Use the CURSOR keys to select On or OFF and
press ENTER.
No Signal Shut-Off
Use the Mode (Home/Store) option if you would like to
change the initial Energy Saving Mode chosen at
HDTV’s first power on.
Home Mode - Configured for saving energy and power
consumption reduction.
Store Mode - Configured for high brightness and
contrast for display at retailer store.
NOTE: Only Home Mode qualifies for Energy Star.
Press ENTER on the desired mode.
Mode (Home/Store)
Use the Network option to configure your HDTV’s setup
to your Local Area Network (LAN) and enjoy internet
based content directly on your TV.
A subscription to an Internet Service Provider is needed.
Use your HDTV’s wireless capabilities or the Ethernet
port to connect to a modem or router.
Please refer to the Internet Ready HDTV Guide for more
information.
Network
11
Need help? www.sanyoctv.com 1-800-877-5032
CHANNEL _________________________
Auto – Search the detected mode, Cable or Air.
Cable – Search for analog and unscrambled (ClearQAM)
digital cable channels.
Air (Antenna) – Search for analog and digital off-air
channels.
Digital Add-On – Search for digital channels adding newly
found digital channels to the channel map database.
NOTE: Digital Add-On option is not available when the
current mode is Cable.
Channel Search
Display the On Screen menu and use the CURSOR
keys to select Channel. Press ENTER.
ON-SCREEN MENU OPERATION
Channel Scan Memory lists all Analog and Digital channels found. It also lists Analog channels that were not
found, which can be added.
Use the CURSOR keys to move the channel select
bar through all enabled and disabled channels.
NOTE: You may use the
CH
keys to change page.
Press ENTER to enable or disable the selected channel.
Channel Scan Memory
For V-Chip (Movie) ratings select Movie and press
ENTER, and then select the desired MPAA rating limit.
Press the EXIT key to close the V-Chip menu.
For V-Chip (TV) ratings select TV and press ENTER. Use
the CURSOR keys to select a rating and press
ENTER. Use the CURSOR keys to set the rating’s
status as Blocked or Viewable. Once ratings are set,
press the EXIT key to close the V-Chip menu.
NOTE: Some TV ratings offer more detailed settings
such as Dialogue, Language, Sexual, and
Violence.
ADVANCED V-CHIP SYSTEM (RRT5)
RRT5 (V-Chip Regional Ratings 5) is an advanced V-Chip
ratings system for over the air digital channels. When the
HDTV detects compatible RRT5 data, it’s downloaded &
stored in memory, and the Setup V-Chip screen is then
modified to show the Adjust (Advanced) option.
Use the CURSOR and keys to highlight the
different options, and use the ENTER key to block or
unblock the selected rating.
NOTE: When vertical scroll bars appear, press
CURSOR
to gain access to the additional ratings.
MORE INFORMATION
Additional information about MPAA (Motion
Picture Association of America) and V-Chip rating
can be found at: www.mpaa.org and www.vchip.org, respectively.
NOTE: For information on local digital channels, visit
www.antennaweb.org
12
Need help? www.sanyoctv.com 1-800-877-5032
PICTURE _________________________
ON-SCREEN MENU OPERATION
Display the On Screen menu and use the CURSOR
keys to select Picture. Press ENTER.
You may choose a Picture Mode between Standard,
Vivid, Theater, and Stadium which have predetermined
picture parameter values, or choose the Custom option
for personalized picture settings.
NOTE: Each AV input can have its own picture mode
(predetermined or custom.)
MANUAL (CUSTOM) PICTURE SETTINGS
Custom parameters to adjust include:
•
Color
•
Tint
•
Contrast
•
Brightness • Sharpness• Color Temperature
The Advanced Control option allows for the adjustment
of additional parameters such as:
•
Signal Balancer• Noise Reduction
•
White Balance• Dynamic Contrast
CUSTOMIZING PICTURE SETTINGS
Use the CURSOR keys to highlight the picture parameter you wish to adjust. Press the ENTER key to enter the
value adjustment screen. Modify the selected parameter’s
value by pressing the CURSOR keys.
NOTE: CURSOR keys select the next/previous
parameter without returning to the previous
menu screen.
Once adjustments are complete, press the EXIT key to
return to normal TV viewing.
ADDITIONAL PICTURE OPTIONS:
Select Picture Options to access power consumption
reduction features such as ECO and Light Sensor, as
well as horizontal and vertical stretch parameters.
ECO (ENERGY SAVER)
ECO settings control the LCD backlight brightness to
reduce power consumption.
• Level 1: Energy Saver feature is off.
• Level 2: Lower power consumption.
• Level 3: Lowest power consumption.
Press ENTER on the desired level.
NOTE: ECO key on remote may also be used as a short-
cut to modify the Energy Saver settings.
LIGHT SENSOR
This feature detects ambient room light brightness and
uses that reading to control the panel brightness level
and picture parameters to reduce the HDTV’s power
consumption.
NOTE: When room lighting is dark, the panel bright-
ness and/or the picture setting parameters such
as brightness and contrast are lowered. When
room lighting is bright, parameters are affected
opposite.
H-SIZE & V-SIZE
H-Size function adjusts the screen’s horizontal dimensions, while the V-Size function adjust’s the screen’s
vertical dimensions.
Once adjustments are complete, press the EXIT key to
return to normal TV viewing.
Loading...