Samsung SYNCMASTER SWA5000, SWA-5000 User Manual

Wireless Receiver Module

Model : SWA-5000

Thank you for purchasing this product (SWA-5000).

For more detailed information on how to connect and use the
Wireless Receiver Module (SWA-5000), refer to the Owner's
Manual of Samsung Home Cinema (with TX Card port).

If the main unit doesn't make wireless connection, the system needs ID Setting between main unit and
wireless receiver module. With the main unit turned off, press remote control's number button "0"

 "5", then between the main unit and the wireless receiver module are ready for pairing.

With the wireless receiver module turned on, press "ID SET" button on the back of the unit for 5 seconds.

Accessories

 "1"  "3"

Wireless Receiver Module

a The TX card will be not provided for a home theater model that has no TX CARD

CONNECTION(WIRELESS JACK) port installed.

Specifications

Power Consumption 50W

Weight 1.1 Kg

Dimensions (W x H x D) 76.2 x 228 x 152 mm

Operating Temperature Range +5

Operating Humidity Range 10% ~ 75%

Output Refer to the Owner’s Manual of the Samsung product.

Frequency range 20Hz~20KHz

S/N Ratio 65dB

SWA-5000-ENG_0607.indd 1SWA-5000-ENG_0607.indd 1 2010-06-07  3:27:342010-06-07  3:27:34

°C

TX Card

~ +35

Speaker Cable (2EA)

°C

Safety Warnings

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE REAR COVER. NO USER
SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.

WARNING:

To reduce the risk of fire or electric shock, do not expose this appliance to rain or

This symbol indicates that dangerous
voltage which can cause electric
shock is present inside this unit.

This symbol alerts you to important
operating and maintenance
instructions accompanying the unit.

moisture.

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE

SLOT, FULLY INSERT.

Wiring the Main Power Supply Plug(UK Only)

IMPORTANT NOTICE

The main lead on this equipment is supplied with a moulded plug incorporating a fuse. The value of the fuse is indicated on the
pin face of the plug and if it requires replacing, a fuse approved to BS1362 of the same rating must be used.

Never use the plug with the fuse cover removed. If the cover is detachable and a replacement is required, it must be of the same
colour as the fuse fitted in the plug. Replacement covers are available from your dealer.

If the fitted plug is not suitable for the power points in your house or the cable is not long enough to reach a power point, you
should obtain a suitable safety approved extension lead or consult your dealer for assistance.

However, if there is no alternative to cutting off the plug, remove the fuse and then safely dispose of the plug. Do not connect
the plug to a main socket as there is a risk of shock hazard from the bared flexible cord.

Never attempt to insert bare wires directly into a main socket. A plug and fuse must be used at all times.

IMPORTANT

The wires in the main lead are coloured in accordance with the following code:–

BLUE = NEUTRAL BROWN = LIVE

As these colours may not correspond to the coloured markings identifying the terminals in your plug, proceed as
follows:–
The wire coloured BLUE must be connected to the terminal marked with the letter N or coloured BLUE or BLACK.
The wire coloured BROWN must be connected to the terminal marked with the letter L or coloured BROWN or RED.

WARNING: DO NOT CONNECT EITHER WIRE TO THE EARTH TERMINAL WHICH IS

MARKED WITH THE LETTER E OR BY THE EARTH SYMBOL

, OR

COLOURED GREEN OR GREEN AND YELLOW.

SWA-5000-ENG_0607.indd 2SWA-5000-ENG_0607.indd 2 2010-06-07  3:27:372010-06-07  3:27:37