Samsung SND-3080, SND-3080P User Manual
SND-3080(P)
imagine the possibilities
Thanks you for purchasing this Samsung product.
To receive a more complete service, please visit
our website
User Manual
Network Camera
RoHS compliant
Our product complies with “The Restriction Of the use of certain Hazardous
Substances in electrical and electronic equipment”, and we do not use the
6 hazardous materials- Cadmium (Cd), Lead (Pb), Mercury (Hg), Hexavalent
Chromium (Cr
+6
), Poly Brominated Biphenyls (PBBs), Poly Brominated Diphenyl
Ethers (PBDEs)- in our products.
2_ overview
overview
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
CAUTION
:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol indicates that dangerous voltage consisting a
risk of electric shock is present within this unit.
This symbol indicates that there are important operating and
maintenance instructions in the literature accompanying this
unit.
WARNING
To reduce the risk of fire or electric shock, do not expose this appliance to
rain or moisture.
To prevent injury, this apparatus must be securely attached to the floor/
wall in accordance with the installation instructions.
If this power supply is used at 24V ac, a suitable plug adapter should be
used.
The camera is to be only connected to PoE networks without routing to
the outside plant.
WARNING
Be sure to use only the standard adapter that is specified in the
specification sheet.
Using any other adapter could cause fire, electrical shock, or damage to
the product.
Incorrectly connecting the power supply or replacing battery may cause
explosion, fire, electric shock, or damage to the product.
Do not connect multiple cameras to a single adapter. Exceeding the
capacity may cause abnormal heat generation or fire.
Securely plug the power cord into the power receptacle. Insecure
connection may cause fire.
When installing the camera, fasten it securely and firmly. The fall of
1.
2.
3.
4.
5.
English _3
● OVERVIEW
camera may cause personal injury.
Do not place conductive objects (e.g. screwdrivers, coins, metal parts,
etc.) or containers filled with water on top of the camera. Doing so may
cause personal injury due to fire, electric shock, or falling objects.
Do not install the unit in humid, dusty, or sooty locations. Doing so may
cause fire or electric shock.
If any unusual smells or smoke come from the unit, stop using the
product. In such case, immediately disconnect the power source and
contact the service center. Continued use in such a condition may
cause fire or electric shock.
If this product fails to operate normally, contact the nearest service
center. Never disassemble or modify this product in any way. (SAMSUNG
is not liable for problems caused by unauthorized modifications or
attempted repair.)
When cleaning, do not spray water directly onto parts of the product.
Doing so may cause fire or electric shock
Do not expose the product to the direct airflow from an air conditioner.
Otherwise, it may cause moisture condensation inside the Clear Dome
due to temperature difference between internal and external of the
dome camera.
If you install this product in a low-temp area such as inside a cold store,
you must seal up the wiring pipe with silicon, so that the external air can
not flow inside the housing.
Otherwise, external high, humid air may flow inside the housing, pooling
moisture or vapor inside the product due to a difference between
internal and external temperature.
CAUTION
Do not drop objects on the product or apply strong blows to it. Keep
away from a location subject to excessive vibration or magnetic
interference.
Do not install in a location subject to high temperature (over 50°C), low
temperature (below -10°C), or high humidity. Doing so may cause fire or
electric shock.
If you want to relocate the already installed product, be sure to turn off
the power and then move or reinstall it.
Remove the power plug from the outlet when there is a lighting storm.
Neglecting to do so may cause fire or damage to the product.
Keep out of direct sunlight and heat radiation sources. It may cause fire.
Install it in a place with good ventilation.
Avoid aiming the camera directly towards extremely bright objects such
as sun, as this may damage the CCD image sensor.
6.
7.
8.
9.
10.
11.
12.
1.
2.
3.
4.
5.
6.
7.
overview
4_ overview
Apparatus shall not be exposed to dripping or splashing and no objects
filled with liquids, such as vases, shall be placed on the apparatus.
The Mains plug is used as a disconnect device and shall stay readily
operable at any time.
When using the camera outdoors, moisture may occur inside the
camera due to temperature difference between indoors and outdoors.
For this reason, it is recommended to install the camera indoors. For
outdoor use, use the camera with built-in fan and heater.
FCC STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions :
1) This device may not cause harmful interference, and
2) This device must accept any interference received including interference that
may cause undesired operation.
CAUTION
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of FCC Rules. These limits are
designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct
the interference at his own expense.
IC Compliance Notice
This Class A digital apparatus meets all requirements of the
Canadian Interference.-Causing Equipment Regulations of
ICES-003.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
8.
9.
10.
English _5
● OVERVIEW
IMPORTANT SAFETY INSTRUCTIONS
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
Do not install near any heat sources such as radiators, heat registers, or other apparatus
(including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding-type plug.
A polarized plug has two blades with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide blade or the third prong is
provided for your safety. If the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
Only use attachments/accessories specified by the manufacturer.
Use only with the cart, stand, tripod, bracket, or table specified by
the manufacturer, or sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus combination to avoid
injury from tip-over.
Unplug this apparatus during lightning storms or when unused for
long periods of time.
Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as powersupply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate normally, or has been dropped.
Apparatus shall not be exposed to dripping or splashing and no objects
filled with liquids, such as vases, shall be placed on the apparatus
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
overview
6_ overview
overview
2
5 Important Safety Instructions
8 Product Features
8 Recommended PC Specifications
9 What’s Included
10 At a Glance
CONTENTS
installation &
connection
14
14 Removing the covers
15 Connecting With Other Device
17 Installation
camera setup
20
20 How to use the Keyboard
controller
21 Main Menu
21 Profile
22 Camera Setup
26 Privacy Zone
27 Others
28 System Info
28 Language
network connection
and setup
29
29 Connecting the Camera to an
IP Router with the xDSL/Cable
Modem
30 Connecting the Camera to
an IP Router with Local area
Networking
31 Connecting the Camera Directly
to a DHCP-Based xDSL/Cable
Modem
32 Connecting the Camera Directly
to Local area Networking
33 IP Address Setup
34 Static IP Setup
37 Dynamic IP Setup
38 Port Range Forward
(Port Mapping) Setup
38 Connecting to the Camera from a
Shared Local PC
39 Connecting to the Camera from a
Remote PC via the Internet
English _7
● OVERVIEW
web viewer
40
40 Connecting to the Camera
41 Login
42 Installing ActiveX
43 Using the Live Screen
44 Backup
setup screen
46
46 Accessing the Setup Screen
47 Default Setup
51 System Setup
54 Overlay Setup
55 Event Setup
60 Network Setup
appendix
62
62 Profile
63 Terminology
64 Specifications
68 Frame Rate (NTSC)
74 Frame Rate (PAL)
80 Troubleshooting
overview
8_ overview
PRODUCT FEATURES
Support various communication protocols
Supports TCP/IP, UDP, RTP/RTSP, SMTP for email, and FTP protocols as well as various
internet protocols such as ARP, HTTP, HTTPS and DHCP.
Web Browser-based Monitoring
Using the Internet web browser to display the image in a local network environment.
Automatic Local IP Setup
Even a network novice can install it with minimum operations.
Alarm
If the camera equipped with an alarm sensor senses any motion, it will send a notification
to a user FTP/email account (SMTP) or send the corresponding signal to the Alarm Out
terminal.
Motion Detection
If the camera with a specified motion area detects a motion in that area, it will send a
notification to a user FTP/email account (SMTP) or send the corresponding signal to the Alarm
Out terminal.
RECOMMENDED PC SPECIFICATIONS
CPU : Pentium4 / 2.4GHz or higher
Operating System : Windows XP(Service Pack2, Service Pack3) / Windows Vista / Windows 7
Resolution : 1024X768 pixels or higher
RAM : 512MB or higher
Web Browser : Internet Explorer 6.0 or higher
Video Card : Radeon, Nvidia
Video Memory: 128MB
DirectX 8.1 or higher
Compatible IP Routers
Linksys
D-Link
Netgear
Compatible PoE Switches
Linksys SRW224G4P
D-Link DES-1316
SMC SMCPWR-INJ3
English _9
● OVERVIEW
WHAT’S INCLUDED
Please check if your camera and accessories are all included in the product package.
Camera
User Manual/
IP INSTALLER DVD
User Manual
+
(For the iron plate)
Test Monitor Cable Screw Dust-proof Plate
The Test Monitor Cable is connected to a portable displayer and used for testing the camera.
If you intend to use it for an actual monitoring camera, use the BNC cable instead.
M
overview
10_ overview
AT A GLANCE
Appearance
Item Description
Dome Cover Case cover used to protect the lens and the main unit.
Main Unit
Consists of: lens, switch board, PCB and screws.
Power Port
Used to plug in the power cable.
Video Output Port
Used to connect the Video In connector of the monitor, from which the video
signal of the camera outputs.
Network Port Used to connect the PoE or LAN cable.
Wipe out a dirty surface of the lens softly with a lens tissue or cloth to which you have applied
ethanol.
M
English _11
● OVERVIEW
Inside
Item Description
Alarm I/O Port
Consists of two different ports:
- ALARM IN : Used to receive the alarm input signal.
- ALARM OUT : Used to output the alarm output signal.
- GND : Used for earth-grounding.
Reset Button
Restores all camera settings to the factory default. Press and hold it for
about 3 seconds to turn off the system indicator and restart the system.
J
After resetting the camera, you must run the IP Installer program to
change the basic network settings such as IP address, Subnet mask,
Gateway, etc., before you can connect to the network.
overview
12_ overview
Components
4 5
6
Lens
1
2
3
9
7
8
English _13
● OVERVIEW
Item Description
Inner Cover Cover used to protect the main unit.
Wing-Side Hook Tap on either end to remove the inner cover.
Monitor Out
The Test Monitor Cable is connected to a portable displayer and used for
testing the camera.
Zoom Lever Used to adjust or fix the zoom factor of the lens.
Focus Lever Turn it to the left or right to adjust the focus; turn it clockwise to fix the focus.
Tilt Screw Used to adjust or fix the tilt of the lens.
Bracket Used to install the camera on the wall or ceiling with the screws.
Wiring Cover
If you drill a hole in the wiring cover for wiring,
remove the cover and attach the provided dustproof plate to it, and arrange the cables through the
plate.
The dust-proof plate is to prevent outside dust from
inflow to the wiring compartment.
Release Lock
If you want to remove the bracket from the main unit or remove the camera
from the bracket, push this out and turn the main unit in the <UNLOCK>
direction.
14_ installation & connection
installation & connection
REMOVING THE COVERS
If you want to connect the Alarm I/O connectors, you must remove the dome cover and lens
cover beforehand.
Turn the dome cover counter-clockwise.
Remove the dome cover by lifting it up.
Tap on either end of the lens cover to remove it.
1.
2.
3.
English _15
● INSTALLATION & CONNECTION
CONNECTING WITH OTHER DEVICE
Power Supply
Connect the power adaptor to the power input port.
Be careful not to reverse the polarity when you connect the power cable.
You can also use a router featuring PoE (Power over Ethernet) to supply power to the camera.
Connecting to the monitor
Connect the [V_OUT] port of the camera to the video input port of the monitor.
Network Connection
Connect the Network cable to the local network or to the Internet.
J
Monitor
Power
Network
installation & connection
16_ installation & connection
Connecting to the I/O port box
Connect the Alarm I/O cable to the corresponding port of the inner port box.
ALARM IN 1, 2 : Used to connect the alarm input signal.
GND : Used for earth-grounding.
ALARM OUT 1, 2 : Used to connect the alarm output signal.
Alarm I/O Wiring Diagram
1
ALARM IN 1
ALARM OUT 1
ALARM OUT 2
ALARM IN 2
GND
2
3
4
5
External Relay
External Relay
ALARM IN
ALARM OUT
GND
English _17
● INSTALLATION & CONNECTION
INSTALLATION
Precautions before installation
Ensure you read the following instructions before installing the camera:
Select an installation site (ceiling or wall) that can endure at least 5 times of the camera
weight.
Stuck-in or peeled-off cables can cause damage to the product or a fire.
For safety purposes, keep anyone else away from the installation site. And put aside
personal belongings from the site, just in case.
Installing the camera
Hold down the bottom lock lever while
removing the cover with the other hand.
Removing the cover reveals the main unit
and inner cover.
To fix the camera position, hold down either
hook of the inner cover and lift it up.
Push the release lock out while turning the
main unit in the <UNLOCK> direction to remove
the bracket.
If this doesn't work, use the hole on the bottom
of the bracket to turn the bracket in the <LOCK>
direction.
1.
2.
3.
installation & connection
18_ installation & connection
Use the provided screws (x3) to fix the
bracket to a desired position (ceiling or wall).
Ensure that the <CAMERA FRONT> label on the
bracket faces the direction for camera monitoring.
Arrange the cables through the bracket to the ceiling or wall.
If you drill a hole in the ceiling cover for wiring, press hard to remove the cover and
attach the dust-proof plate to it, and arrange the cables through the plate. If you
intend to arrange the cables without drilling a hole, use the empty area opposite to
the <CAMERA FRONT> label side for the wiring purpose.
Mount the main unit onto the bracket.
Align the marking hole of the main unit with the <CAMERA FRONT> label of the
bracket, and turn the unit in the <LOCK> direction.
Adjust the lens in a desired direction.
For adjusting the lens direction, refer to "Adjusting the monitoring direction for the
camera".
Secure the inner cover to the main unit.
Fit the two holes of the wing-side locks on the inner cover into the corresponding
hole of the main unit, and press it down until you hear a click.
Fix the cover to the main unit.
Fit the protruding part inside the cover into the corresponding hole of the main unit,
and turn the cover to fix it.
4.
5.
6.
7.
8.
9.
Wiring Cover
English _19
● INSTALLATION & CONNECTION
Adjusting the monitoring direction for the camera
You can adjust the camera direction only when the camera is fixed on the ceiling.
Then, turning the camera to the left or right is referred to as "Panning", while tilting the angle
is "Tilting". For panning, the panning limit is 220˚ for the clockwise, and 120˚ for the counterclockwise, a total of 340˚ enabled; further rotation is stopped by the stopper.
Panning
Tilting
Lens rotation
20_ camera setup
camera setup
You can configure the camera settings using the Web Viewer.
For accessing the Web Viewer, refer to "Network Connection and Setup". (page 29)
HOW TO USE THE KEYBOARD CONTROLLER
Follow the steps below if you run the Web Viewer for setting the menus.
Launch the Web Viewer.
From the [Camera OSD] menu in the left
pane, click [Menu].
The <MAIN MENU> screen appears.
Click the Up/Down (
$%
) buttons to move to a
desired item.
Click
the four direction (
$%_ +
) buttons to navigate through the menu items.
To change the value of a selected item, click the Left/Right (
_ +
) buttons.
Click [ ].
Your changes will be applied.
: Exits the menu setup screen.
Before exiting the setup screen, select [SAVE] to save your settings, or [QUIT] to
cancel them.
: Saves your settings and returns to the previous screen.
: Returns to the main menu.
: Use this icon if you want to save your settings after you specified the mask area and
privacy area, etc.
Once you saved your settings, the changes remain intact even if you select [QUIT] on
exit.
: Use this icon if you want to delete a mask, or privacy area, etc.
Once you deleted your settings, the deletions remain valid even if you select [QUIT] on
exit.
: This arrow appears next to a menu that contains sub items.
For the items with the "*" mark on the right, You can get help from "Terminology". (page 63)
M
1.
2.
3.
4.
5.
6.
English _21
● CAMERA SETUP
MAIN MENU
You can configure the camera settings to your preference.
PROFILE
You can select a mode that is appropriate to the
camera installation environment.
CAMERA SET
Configure the camera functions and settings.
PRIVACY ZONE
You can configure the privacy settings.
OTHER SET
You can configure more settings including
FACTORY DEFAULTS.
SYSTEM INFO
Shows the camera version and type.
LANGUAGE
Select a preferred one from the supported languages.
PROFILE
You can select one from the pre-determined modes as appropriate to your specific camera installation
environment.
Your selection on each item in PROFILE will affect all other settings of the camera. For the
setting, refer to "PROFILE". (page 62)
For selecting and saving each menu item, refer to "How to use the keyboard controller". (page 20)
STANDARD
Automatically optimizes the camera settings to
the normal environment.
ITS
This setting enables you to analyze the traffic
situation and take the traffic information at a glance.
BACKLIGHT
This setting enables you to view a sharp background
and object even in a severe backlight scene.
DAY/NIGHT
Automatically optimizes the camera settings to the day and night scene.
GAMING
This automatically configures the settings so that you can work in a stable illumination
condition as indoors.
CUSTOM
Your change to any of the PROFILE settings will switch the display to CUSTOM.
** MAIN MENU **
PROFILE
CAMERA SET
PRIVACY ZONE
OTHER SET
SYSTEM INFO
LANGUAGE
◄
PROFILE
►
*STANDARD
ITS
BACKLIGHT
DAY/NIGHT
GAMING
CUSTOM
22_ camera setup
camera setup
CAMERA SETUP
You can configure the general settings of the camera module.
Use the four direction (
$%_ +
) buttons to select a desired item.
CAMERA ID
Provide the ID and position for a camera that displays on the screen.
For selecting and saving each menu item, refer to "How to use the keyboard controller". (page 20)
Select <CAMERA SET> - <CAMERA ID>.
Use the four direction (
$%_ +
) buttons to
select a desired character.
In the lower input box of the screen, the
selected character will be entered.
You can enter up to 54 characters including letters,
numbers and special characters..
When done, continue to select <LOCATION>
to specify the display position of the camera ID.
IRIS
You can set the iris to control the intensity of radiation incoming to the camera.
For selecting and saving each menu item, refer to "How to use the keyboard controller". (page 20)
Select <CAMERA SET> - <IRIS>.
Use the left/right (
_ +
) buttons to select <ALC>.
LEVEL : Select an overall brightness level.
BACKLIGHT :
Select either <BLC> or <WDR>.
WDR : Specify the synthesis level in
the WEIGHT, and shutter speed in the
WDR LEVEL, or select <OUTDOOR> or
<INDOOR> in the WHITE BAL.
BLC : Set the <BLC> area by specifying the
<SIZE> and <POSITION>.
If the iris is set to <ALC>, fixing the iris is your priority when you adjust AE and the shutter speed.
1.
2.
3.
1.
2.
-
-
M
CAMERA ID
ABCDEFGHIJKLMNOPQRSTUVWXYZO
123456789
: ?_+* ()/
SP►► ◄◄ SP LOCATION
- - - - - - - - - - - - - - - - - - - - - - - - -
- - - - - - - - - - - - - - - - - - - - - - - - -
ALC
LEVEL [ 00] ---- I ----
BACKLIGHT OFF
English _23
● CAMERA SETUP
MOTION
You can specify a level of AGC for controlling the
camera motion.
Select F.FAST if you want to monitor a very fast
moving object in a low contrast scene, and S.SLOW
if monitoring a very slow moving, inanimate object in
the same condition.
As long as DAY/NIGHT is set to AUTO, the
<MOTION> menu is not available.
DNR
Reduces the noise on the screen.
This is useful, especially for a noisy screen.
Set it to <USER>, you can specify the level.
SHUTTER
The SHUTTER menu is used to set the fixed fast
electronic shutter or auto fast electronic shutter.
SENS-UP
If the brightness of the video signal is too low, the Slow Shutter function will be activated.
Slow Shutter can collect the individual max frame rate to adjust the setting.
FLICKERLESS
If set to <ON>, the shutter speed will be fixed to 1/100 second. This will prevent possible
screen distortion due to a mismatch between the vertical sync frequency and the blinking
frequency of the lighting.
If SHUTTER is set to AUTO, FIX, EXT mode / SENSE UP to FIX / AGC to FIX, the <DIS> menu will be
disabled.
XDR
This will correct a brightness difference between different scenes for the optimal visibility.
The higher the value is, the higher the correction level is.
DIS
Automatically compensates for the flicker on the screen.
If set to <ON>, the image will be enlarged with digital zoom as much area as
compensated.
◄
CAMERA SET
►
CAMERA ID ON
IRIS ALC
MOTION (F.FAST)
--DNR MID
SHUTTER OFF
SENS-UP AUTO X4
FLICKERLESS OFF
XDR MID
DIS OFF
DAY/NIGHT AUTO
WHITE BAL
DIGITAL ZOOM OFF
DETAIL
[2]
AGC COLOR SUP MID
REVERSE OFF
POSI/NEGA +
PIP OFF
24_ camera setup
camera setup
DAY/NIGHT
You can specify a recording mode according to the scene.
For selecting and saving each menu item, refer to "How to use the keyboard controller". (page 20)
Select <CAMERA SET> - <DAY/NIGHT>.
Select a screen transition mode according to the
illumination, and set options as appropriate.
DAY : Fixed to DAY mode, regardless of the
scene.
NIGHT : Fixed to NIGHT mode, regardless
of the scene.
If BURST is set to <ON>, the burst signal will
output.
AUTO : According to the luminance, this will
switch DAY to NIGHT mode, or vice versa.
DAYNIGHT / NIGHTDAY : If set to
<AUTO>, you can specify the brightness
level triggering the mode switch between
DAY and NIGHT as well as the interval.
MASK AREA : If there exists a bright spot
light source in a night scene, you can specify
the size and position as needed.
Any excessively bright area in a night scene
will be masked.
WHITE BAL
If you need to adjust the screen brightness, use the WHITE BALANCE function.
For selecting and saving each menu item, refer to "How to use the keyboard controller". (page 20)
Select <CAMERA SET> - <WHITE BAL>.
Select a mode where you set the balance.
DAY : You can set the RED, and BLUE value
in DAY mode.
NIGHT : You can adjust the <WHITE BAL>
according to the ambient luminance.
1.
2.
1.
2.
AUTO
BURST OFF
DAYNIGHT
BRIGHTNESS MID
DWELL TIME 2S
NIGHTDAY
BRIGHTNESS MID
DWELL TIME 5S
MASK AREA 1 2
WHITE BAL
DAY/NIGHT DAY
MODE ATW2
RED
[ 00] ----
I
----
BLUE
[ 00] ----
I
----
MASK AREA
<SIZE>
<LOCATION>
English _25
● CAMERA SETUP
According to the specified recording mode,
select a WHITE BAL mode with necessary
options.
BRIGHTNESS : Specify a brightness level
triggering the switch from DAY to NIGHT
mode.
MODE : According to the selected mode, you
can adjust the RED and BLUE color level.
RED : Adjust the strength of the red color.
BLUE : Adjust the strength of the blue
color.
R-GAIN/B-GAIN : Specify the current color temperature manually.
You can set the R-GAIN, and B-GAIN value only in AWC mode.
DIGITAL ZOOM
You can set the digital zoom factor and position.
When the zoom factor and position are defined, the digital zoom function will operate.
If you set the digital zoom to a larger factor than the actual enlargement for compensation, the DIS
function will be disabled.
DETAIL
You can adjust the vertical and horizontal sharpness, respectively.
AGC COLOR SUP
This will adjust the color scheme according to the AGC value.
REVERSE
This will reverse the signal left to right, top to bottom, or a combination of the preceding.
POSI/NEGA
This will display the video brightness signal either normally or reversely.
PIP
You can view a main image with a sub image on the same screen.
3.
-
-
-
WHITE BAL
DAY/NIGHT NIGHT
BRIGHTNESS MID
MODE AWC
RED
[ 00] ----
I
----
BLUE
[ 00] ----
I
----
R-GAIN
[
0040]
B-GAIN
[
0133]
26_ camera setup
camera setup
PRIVACY ZONE
You can set up to 12 privacy zones that will be hided for privacy of the subject when recording.
For selecting and saving each menu item, refer to "How to use the keyboard controller". (page 20)
ZONE SETUP
Select <MAIN MENU> - <PRIVACY ZONE>.
Use the four direction (
$%_ +
) buttons to
select a desired number.
The Zone setup screen appears.
Select the <PIXEL LEVEL>.
Specify the pixel unit level for the POSITION setting.
Select <POINT>.
You will see dots on the screen.
Use the four direction (
$%_ +
) buttons to specify
the position for each of the four dots.
Select <POSITION> and use the four direction
(
$%_ +
) buttons to specify the position for each
of the four dots.
Save the changes and move to the previous screen and select the <STYLE>.
Select <COLOR> and pick a desired color.
Setting one or more privacy zone and enabling privacy function will disable the PIP function.
1.
2.
3.
4.
5.
6.
7.
M
PRIVACY ZONE SET 1
PIXEL LEVEL
[4]
<POINT>
<POSITION>
◄
PRIVACY ZONE
►
1 2 3 4 5 6
7 8 9 10 11 12
PRIVACY SET
ON
STYLE
MOSAIC1
English _27
● CAMERA SETUP
OTHERS
You can reset the camera, or select the OSD font color to your preference.
For selecting and saving each menu item, refer to "How to use the keyboard controller". (page 20)
FACTORY DEFAULT
Select <MAIN MENU> - <OTHER SET>
- <FACTORY DEFAULTS>.
The FACTORY DEFAULTS setup screen
appears.
Select <OK>.
All the settings will be restored to the factory
default.
However, the language setting will not be
restored.
OSD COLOR
You can set the font color of the user interface.
1.
2.
◄
OTHER SET
►
FACTORY DEFAULTS
OSD COLOR BW
FACTORY DEFAULTS
OK
CANCEL
28_ camera setup
camera setup
SYSTEM INFO
You can check the system information.
For selecting and saving each menu item, refer to "How to use the keyboard controller". (page 20)
Select <MAIN MENU> - <SYSTEM INFO>.
The current system information is displayed.
The camera type may different, depend on the video
signal.
LANGUAGE
You can select a language to your preference.
For selecting and saving each menu item, refer to "How to use the keyboard controller". (page 20)
Select <MAIN MENU> - <LANGUAGE>.
Select your preferred language using the
up/down (
▲▼
) buttons.
Supported language may different.
1.
2.
M
1.
2.
M
◄
SYSTEM INFO
►
TYPE 3_IPV_N
CAMERA VER. v1.00_090724
◄
LANGUAGE
►
*ENGLISH
FRANÇAIS
DEUTSCH
ESPAÑOL
ITALIANO
English _29
●
NETWORK CONNECTION AND SETUP
network connection and setup
You can set up the network settings according to your network configurations.
Before installing or while using this program, visit the Samsung website www.samsungsecurity.com
and download and upgrade with the latest S/W version available.
CONNECTING THE CAMERA TO AN IP ROUTER WITH THE
XDSL/CABLE MODEM
This is for a small network environment such as homes, SOHO and ordinary shops.
Configuring the network settings of the local PC connected to an
IP router
Configuring the network settings of the local PC connected to an IP router, follow the
instructions below.
Select : <Network Neighborhood> <Properties> <Local Area Connection>
<Properties> <General> <Internet Protocol (TCP/IP)> <Properties>
<Obtain an IP address automatically> or <Use the following IP address>.
Follow the instructions below if you select <Use the following IP address>:
ex1) If the address (LAN IP) of the IP router is 192.168.1.1
IP address: 192.168.1.100
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.1.1
ex2) If the address (LAN IP) of the IP router is 192.168.0.1
IP address: 192.168.0.100
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.0.1
M
로컬PC
IP공유기
xDSL 또는
Cable 모뎀
xDSL 또는
Cable 모뎀
외부 원격 PC
DDNS 서버
(Data Center, KOREA)
SND-3080
SND-3080
Local PC
IP Router
xDSL or
Cable Modem
xDSL or
Cable Modem
External Remote PC
DDNS Server
(Data Center, KOREA)
INTERNET
30_ network connection and setup
network connection and setup
ex3) If the address (LAN IP) of the IP router is 192.168.xxx.1
IP address: 192.168.xxx.100
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.xxx.1
For the address of the IP router, refer to the product’s documentation.
Checking if the IP router is connected to the xDSL/Cable modem properly
Select <Status> from the Settings menu of the IP Router
If it is properly connected, <IP Address>, <Subnet Mask> and <Gateway>
provided by your ISP are displayed. Please remember these values because they
are required so that an external remote computer of the IP router connects to the
camera. However, note that certain ISPs change the settings of <IP Address>,
<Subnet Mask> and <Gateway> on a regular basis
If the IP router is not properly connected, press the [Connect] button to try to recon-
nect or check if the settings of the IP router are correct.
CONNECTING THE CAMERA TO AN IP ROUTER WITH
LOCAL AREA NETWORKING
This is for a large network environment such as corporate office, building, public office and factory.
Configuring the network settings of the local PC connected to an
IP router
Configuring the network settings of the local PC connected to an IP router, follow the
instructions below.
M
로컬 PC
방화벽
IP 공유기
외부 원격 PC
DDNS 서버
(Data Center, KOREA)
SND-3080
SND-3080
Local PC
IP Router External Remote PC
DDNS Server
(Data Center, KOREA)
Local PC
Firewall
INTERNET
Switch
HUB
Loading...