Safety precautions are important for your own security. Please read the safety precautions thoroughly.
1. Use the anti-static handing procedures included with the anti-static mat to ensure that there is no electrostatic
discharge and component damage.
2. Static electricity is the biggest danger to the PCB parts you are about to disassemble or assemble. It’s important to
use your anti-static wrist strap to prevent damage to these components.
3. Using excessive force during disassembly and assembly can damage locking parts. Use care when handling
“Locking parts” to avoid damage to FPCB or wire. Apply pressure only at the points designated in the maintenance
instructions.
4. Due to increasing environmental concerns, a number of restrictions have been placed on the material content
of electronic components and electronic assemblies. It requires utilizing Lead-Free (Pb-free) Soldering.
5. The following precautions must be observed when handling such components below.
<Table 1-1>
ComponentPrecautions
FPCB
CCD (CMOS)
IR CUT Filter,
LCD, LENS
PCBUse an anti-static mat as well as an anti-static wrist strap to avoid ESD damage to PCB.
CONNECTOR
FPCB is brittle material. It can be easily damaged thus it should be handled with care.
It is recommended to use wooden or plastic tweezers for manual placement.
-The device will be forced to turn off after 3 seconds.
approx. 160 min.approx. 300 min.
approx. 160 min.approx. 300 min.
2-4
Copyrightⓒ 1995-2013 SAMSUNG. All rights reserved.
3. Disassembly and Assembly
3-1 Disassembly
* SCREW SIZE INFROMATION
(M 1.7 X 4 B)
(SCREW TYPE)
M : MACHINE
T : TAPTYPE
(SCREW SIZE)
ASSY RIGHT
1. Remove the three screws.
M1.7 X L9
(SCREW COLOR)
B : BLACK
W : WHITE
S : SILVER
M.SCREW
Fig. 3-1
2. Remove the three screws on the bottom side of the camcorder.
Fig. 3-2
Copyrightⓒ 1995-2013 SAMSUNG. All rights reserved.
M.SCREW
3-1
Disassembly and Assembly
3. Remove the screw from the battery compartment.
M.SCREW
Fig. 3-3
3-2
Copyrightⓒ 1995-2013 SAMSUNG. All rights reserved.
4. After removing the two screws from the COVER LEFT, remove the COVER LEFT.
①②
COVER LEFT
Fig. 3-4
Disassembly and Assembly
5. Remove the two screws.
M.SCREW
Fig. 3-5
Copyrightⓒ 1995-2013 SAMSUNG. All rights reserved.
3-3
Disassembly and Assembly
6. Run a pry tool around the groove to release the locking park. Slightly wiggle it to widen the gap.
You'll have to apply a little force to remove it. Lift it up and set it aside.
Fig. 3-6
7. Remove the wire in the direction of the arrow as illustrated in image A.
(Take care not to pull the wire, which could damage it.)
CAUTION
Use extra care when removing the wire from the connector.
3-4
Image A
Fig. 3-7
Copyrightⓒ 1995-2013 SAMSUNG. All rights reserved.
8. Remove the ASSY RIGHT.
Disassembly and Assembly
Fig. 3-8
ASSY RIGHT
Copyrightⓒ 1995-2013 SAMSUNG. All rights reserved.
3-5
Disassembly and Assembly
ASSY TOP
1. Remove the FPC as illustrated in image A. Then remove the ASSY TOP.
CAUTION
①
Use extra care when removing the FPC from the connector.
Image A
3-6
ASSY TOP
②
Fig. 3-9
Copyrightⓒ 1995-2013 SAMSUNG. All rights reserved.
Disassembly and Assembly
ASSY FRONT
1. Remove the FPC in the direction of the arrow as illustrated in image A. Then remove the ASSY FRONT.
(Take care not to pull the wire, which could damage it.)
CAUTION
Use extra care when removing the FPC from the connector.
Image A
ASSY FRONT
Fig. 3-10
Copyrightⓒ 1995-2013 SAMSUNG. All rights reserved.
3-7
Disassembly and Assembly
ASSY LEFT
1. Remove the two screws.
M.SCREW
3-8
Fig. 3-11
Copyrightⓒ 1995-2013 SAMSUNG. All rights reserved.
2. Remove the FPC as illustrated in image A and B.
Disassembly and Assembly
CAUTION
Use extra care when removing the FPC from the connector.
Image A
Remove the FPC from the connector.
1. Open
FPCB
FPCB
Image B
Fig. 3-12
CONNECTOR
2. Remove
Copyrightⓒ 1995-2013 SAMSUNG. All rights reserved.
3-9
Loading...
+ 37 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.