Samsung EJMT820I User Manual

a

QUICK
START
GUIDE

EJ-MT820I

1. Turn the mouse over and remove the protective
tape from the bottom of the mouse.

2. Loosen and remove the two screws.

3. From the side of the sliding cover, use a flat­edged tool to pry open the bottom part of
the cover.

4. Slide the cover open. Then, loosen and remove
the three screws on the metal connection.

5. Lift the metal connection plate off the two
locating pins and remove the top part of the
sliding cover.

6. Turn the mouse back over and from the front of
the mouse use a flat-edged tool to pry open the
button panel.

7. Loosen and remove the six screws along the
border of the mouse.

8. Pry open the cover to gain access to the circuit
board.

9. Use wire cutters to cut the wires between the
battery and the circuit board.

10. Pry the batter y cover loose from the two
connection points and remove the battery.

Printed in Korea

A00448 Rev.1.0
E Type 04/2015

b

c

d

e

f

g

Copyright © 2015 Samsung Electronics

English

Bluetooth® is a registered trademark of Bluetooth
SIG, Inc. worldwide.

•

Please read this manual before using the device to
ensure safe and proper use.

•

Images may differ in appearance from the actual
product. Content is subject to change without
prior notice. You can access the full user manual
for more information. Visit
to view device information, the user manual,
and more.

•

The mouse is compatible with mobile devices
and computers running Android 4.1 or higher or
Windows 7 or higher.

www.samsung.com

Device layout

Scroll wheel Sliding cover

Right button Charging port

Notification light CONNECT button

Left button

Charging the battery

Before using the mouse for the first time, you must
charge the battery.

Open the charging port cover and connect the
mouse to a computer or the USB power adaptor via
the USB cable.

•

You can charge the device using the
charger (sold separately).

•

The charger should remain close to the
electric socket and easily accessible while
charging.

•

The socket-outlet shall be installed
near the equipment and shall be easily
accessible.

Turning the mouse on and off

Turn on the mouse by sliding the cover open. Close
the cover to turn it off.

When you turn on the mouse for the first
time, it enters Bluetooth pairing mode.

Connecting to another device

1. Press and hold the CONNECT button for more
than three seconds.
The notification light flashes red, green, and
blue and then the mouse enters Bluetooth
pairing mode.

2. On your other device, activate the Bluetooth
feature and tap Samsung Bluetooth Mouse

Slide from the list.

Safety information

Read all safety information before using the device
to ensure safe and proper use. To view the full safety
information, refer to the Samsung website.

Use manufacturer-approved batteries, chargers,
accessories, and supplies

Do not touch the device with wet hands
Do not drop or cause an impact to the charger

or the device
Do not store your device in very hot or very cold

areas. It is recommended to use your device at
temperatures from 5°C to 35°C

Prevent the multipurpose jack and the small
end of the charger from contact with conductive
materials, such as liquids, dust, metal powders,
and pencil leads

Do not allow children or animals to chew or suck
the device

Do not disassemble, modify, or repair your
device

Correct disposal

This marking on the product,
accessories or literature indicates
that the product and its electronic
accessories (e.g. charger, headset,
USB cable) should not be disposed of
with other household waste.

This product is RoHS compliant.

This marking on the battery, manual
or packaging indicates that the
batteries in this product should not
be disposed of with other household
waste.

Removing the battery

•

To remove the battery, you must visit an
authorised service centre with the provided
instructions.

•

For your safety, you must not attempt to remove
the battery. If the battery is not properly removed,
it may lead to damage to the battery and device,
cause personal injury, and/or result in the device
being unsafe.

•

Samsung does not accept liability for any damage
or loss (whether in contract or tort, including
negligence) which may arise from failure to
precisely follow these warnings and instructions,
other than death or personal injury caused by
Samsung’s negligence.

Declaration of Conformity

Product details

For the following

Product :
Model(s) : EJ-MT820I

Declaration & Applicable standards

We hereby declare, that the product above is in compliance with
the essential requirements of the R&TTE Directive (1999/5/EC) by
application of:

EN 301 489-1 V1.9.2 EN 301 489-3 V1.4.1
EN 301 489-17 V2.2.1 EN 55013 : 2001 / A1 : 2003 / A2 : 2006
EN 55020 : 2007 / A11 : 2011 EN 300 328 V1.8.1
EN 302 291-1 V1.1.1 EN 302 291-2 V1.1.1

EN 60950-1 : 2006 + A11 : 2009 + A1 : 2010 + A12 : 2011
and the Directive (2011/65/EU) on the restriction of the use of certain
hazardous substances in electrical and electronic equipment by
application of EN 50581:2012.
The conformity assessment procedure referred to in Article 10 and
detailed in Annex[IV] of Directive 1999/5/EC has been followed with
the involvement of the following Notified Body(ies):

TÜV SÜD BABT, Octagon House, Concorde Way, Fareham,

Hampshire, PO15 5RL, UK*

Identification mark: 0168

Representative in the EU

Samsung Electronics Euro QA Lab. (YEAR TO

Blackbushe Business Park BEGIN AFFIXING

Saxony Way, Yateley, Hampshire CE MARKING 2015

Yateley, Hampshire, GU46 6GG, UK

2014.XX.XX Stephen Colclough / EU Representative

(Place and date of issue) (Name and signature of authorised person)

* This is not the address of Samsung Ser vice Centre. For the address or the

phone number of Samsung Service Centre, see the warranty card or contact
the retailer where you purchased your product.

FCC ID: A3LEJMT820I

FCC Part 15.19
This device complies with part 15 of the FCC
Rules. Operation is subject to the following
two conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.

FCC Part 15.21
Any changes or modifications (including the
antennas) to this
device that are not expressly approved by the
manufacturer
may void the user's authority to operate the
equipment.

IC: 649E-EJMT820I
This device complies with Industry Canada
licence-exempt RSS standard(s).
Operation is subject to the following two
conditions: (1) this device may not cause
interference, and (2) this device must accept
any interference, including interference that
may cause undesired operation of the device.

Le présent appareil est conforme aux CNR
d'Industrie Canada applicables aux appareils
radio exempts de licence.
L'exploitation est autorisée aux deux
conditions suivantes : (1) l'appareil ne doit
pas produire de brouillage, et (2) l'utilisateur
de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le
fonctionnement.