Samsung DV17MSSANR User Manual

SyncMaster 770TFT SyncMaster 870TFT SyncMaster 170T

TFT-LCD Monitor

Owner’s Instructions

Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co., Ltd. is strictly forbidden.

Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.

The

Samsung logo Microsoft, Windows DPMS

and

SyncMaster

and

DDC

are registered trademarks of Video Electronics Standard Association; the

are registered trademarks of Samsung Electronics Co., Ltd.;

Windows® NT

are registered trademarks of Microsoft Corporation;

VESA,

NERGY STAR

name and logo are registered trademarks of the U.S. Environmental Protection Agency (EPA). As an E

NERGY STAR

TAR

Partner, Samsung Electronics Co., Ltd. has determined that this product meets the E

NERGY

guidelines for energy efﬁciency. All other product names mentioned herein may be the trademarks

or registered trademarks of their respective owners.

Table of Contents

Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Unpacking Your LCD Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Setting up Your LCD Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Setting up an Ergonomic Workstation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Monitor location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Workstation height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Viewing angle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Kensington Security Slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Connecting Your LCD Monitor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Getting Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Plug and Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Auto Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Installing the Video Driver. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Windows® 98. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Windows® 95. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Self-Test Feature Check (STFC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Adjusting Your LCD Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

User Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Automatic Save . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Direct-Access Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Brightness. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Auto Adjustment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

OSD Lock/Unlock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

On Screen Display (OSD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Accessing the Menu System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

PowerSaver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Speciﬁcations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Display Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Changing the Stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Removing the Stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Attaching an Arm-Type Stand or Wall Mount Hanger . . . . . . . . . . . . . . . . . . . . . . .25

Maintenance of Your LCD Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . inside back cover

FrançaisDeutschEspañolPortuguese EnglishItaliano

English 1

Safety Instructions

Before connecting the AC power cord to the DC adapter outlet, make sure the voltage

designation of the DC adapter corresponds to the local electrical supply. Never insert anything metallic into the openings in the cabinet of the Liquid Crystal

Display (LCD) monitor; doing so may create the danger of electric shock. To avoid electric shock, never touch the inside of the LCD Monitor. Only a qualiﬁed

technician should open the case of the LCD Monitor. Never use your LCD Monitor if the power cord has been damaged. Do not allow anything

to rest on the power cord, and keep the cord away from areas where people can trip over it.

Be sure to hold the plug, not the cord, when disconnecting the LCD Monitor from an

electric socket. Openings in the LCD Monitor cabinet are provided for ventilation. To prevent overheating,

these openings should not be blocked or covered. Also, avoid using the LCD Monitor on a bed, sofa, rug, or other soft surface. Doing so may block the ventilation openings in the bottom of the cabinet. If you put the LCD Monitor in a bookcase or some other enclosed space, be sure to provide adequate ventilation.

Put your LCD Monitor in a location with low humidity and a minimum of dust

Do not expose the LCD Monitor to rain or use it near water (in kitchens, near swimming

pools, etc.). If the LCD Monitor accidentally gets wet, unplug it and contact an authorized dealer immediately. You can clean the LCD Monitor with a damp cloth when necessary, but be sure to unplug the LCD Monitor ﬁrst.

Place the LCD Monitor on a solid surface and treat it carefully. The screen is made of thin

glass with a plastic front surface and can be damaged if dropped, hit or scratched. Do not clean the front panel with keton-type materials (e.g., acetone), ethyl alcohol, toluene, ethyl acid, methyl, or chloride – these may damage the panel.

Locate your LCD Monitor near an easily accessible AC outlet.

If your LCD Monitor does not operate normally – in particular, if there are any unusual

sounds or smells coming from it – unplug it immediately and contact an authorized dealer or service center.

High temperature can cause problems. Don’t use your LCD Monitor in direct sunlight, and

keep it away from heaters, stoves, ﬁreplaces, and other sources of heat. Unplug the LCD Monitor when it is going to be left unused for an extended period of time.

Unplug your LCD Monitor from the AC outlet before any service.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER

(OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

English 2

Unpacking Your LCD Monitor

Please make sure the following items are included with your monitor. If any items are missing, contact your dealer.

Power Cord

DC-Adapter

EXIT MENUAUTO EXIT

MENUAUTO A B

FrançaisEspañolDeutschItaliano EnglishPortuguese

Manual

Warranty Card

(not available everywhere)

Monitor and Base

Coloriﬁc & Driver

Pivot software

(optional)

15-pin D-Sub Signal Cable

DVI-I Signal Cable (Optional)

(SyncMaster 170T only)

English 3

Setting up Your LCD Monitor

Setting up an Ergonomic Workstation

Consider the advice given below before you install your monitor.

Monitor location

Choose a position that exposes you monitor to the least reﬂection from lights or windows, usually at a right angle to any window.

Workstation height

Place your LCD Monitor so that the top of the screen is slightly below your eye level when you are comfortably seated.

Viewing angle

Tilt the screen backward or forward to a comfortable viewing position.

U T

M E

N U

Figure 1. Tilt the screen

Kensington Security Slot

This monitor offers you the opportunity to secure your monitor using a Kensington-type security device. Kensington lock not included. Refer to your locking device documentation for installation instructions.

Figure 2. Kensington-type security slot location

English 4

Setting up Your LCD Monitor

Connecting Your LCD Monitor

This monitor offers a method for connection to both a PC and a workstation. One or both types of signal cables can be connected to the monitor simultaneously. Determine which connection method(s) you need and refer to the instructions below.

FrançaisEspañolDeutschItaliano EnglishPortuguese

Figure 3.1 Cable Connection (Analog)

Turn off your computer and unplug its power cord.

Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor.

Connect the signal cable to the video port on your computer, video board, video card,

or graphics card. Connect the power cord for your monitor to the DC adapter and connect the adapter

jack to the DC power port on the back of your monitor. Plug the computer and monitor power cords into a nearby power mains outlet.

Turn your computer and monitor on. If your monitor displays an image, it has been

successfully installed. If necessary, install the video driver for this monitor (see “Installing the Video Driver”

on page 7). After your monitor has been fully installed, run Auto Adjustment (see page 12).

English 5

Setting up Your LCD Monitor

(b)

(a)

Figure 3.2 DVI-I Cable Connection (SyncMaster 170T only)

Turn off your computer and unplug its power cord.

Connect the signal cable to the DVI-I connector (1) on the back of your monitor.

Connect the other end of the cable to the video port on the back of your computer. Connect the power cord for your monitor to the power port on the power adapter.

Secure the power adapter cord and the signal cable(s) under the metal prong.

Insert the tab on each side of the hinge cover (b) then attach the stand of the monitor .

Plug the power cords of your computer and your monitor into a nearby outlet.

Turn on your computer and monitor. If your monitor displays an image, installation is

complete. Perform the auto adjustment procedure as described in “Auto Adjustment” on page 7.

(1)

English 6

Setting up Your LCD Monitor

Getting Help

If your monitor does not display an image, check your cable connections and refer to “Troubleshooting” on page 18. If you experience difﬁculties with the quality of the displayed image, run auto adjustment again and refer to “Adjusting Your LCD Monitor” on page 10 or “Troubleshooting” on page 18.

Plug and Play

Our adoption of the new VESA® Plug and Play solution eliminates complicated and time consuming setup. It allows you to install your monitor in a Plug and Play compatible system without the usual hassles and confusion. Your PC system can easily identify and conﬁgure itself for use with your display. This monitor automatically tells the PC system its Extended Display Identiﬁcation (EDID) data using Display Data Channel (DDC) protocols so the PC system can automatically conﬁgure itself to use the LCD Monitor.

Auto Adjustment

Even though your computer system can recognize your new LCD Monitor system, the auto adjustment function will optimize the display settings for use with your computer. Auto Adjustment can be accessed through the On Screen Display, see “Image Lock:” on page 14 or use the direct access instructions below:

FrançaisEspañolDeutschItaliano EnglishPortuguese

Turn on your computer and monitor.

Push the

The screen will dim and you may notice small changes to the screen image.

AUTO

button to open the Auto Adjustment OSD.

Installing the Video Driver

When prompted by the operating system for the monitor driver, insert the Driver diskette included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions as appropriate for the operating system you have.

English 7

+ 21 hidden pages