Samsung BN68-01517A-00 User Manual
Contact SAMSUNG WORLDWIDE
If you have any questions or comments relating to Samsung products,
please contact the SAMSUNG customer care centre.
Country
AUSTRIA 0800-SAMSUNG (726-7864) www.samsung.com/at
BELGIUM 0032 (0)2 201 24 18 www.samsung.com/be
CZECH REPUBLIC
DENMARK 70 70 19 70 www.samsung.com/dk
EIRE 0818 717 100 www.samsung.com/ie
FINLAND 030-6227 515 www.samsung.com/
FRANCE
GERMANY 01805 - SAMSUNG (726-7864) (€ 0,14/Min) www.samsung.com
HUNGARY 06-80-SAMSUNG (726-7864) www.samsung.com
ITALIA 800-SAMSUNG (726-7864) www.samsung.com
LUXEMBURG 0035 (0)2 261 03 710 www.samsung.com/be
NETHERLANDS 0900-SAMSUNG (726-7864) (€ 0,10/Min) www.samsung.com/nl
NORWAY 815-56 480 www.samsung.com/no
POLAND
PORTUGAL 80820-SAMSUNG (726-7864) www.samsung.com/pt
SLOVAKIA 0800-SAMSUNG (726-7864) www.samsung.com/sk
SPAIN 902 10 11 30 www.samsung.com
SWEDEN 0771-400 200 www.samsung.com/se
SWITZERLAND 0800-SAMSUNG (726-7864) www.samsung.com/ch
U.K 0845 SAMSUNG (7267864) www.samsung.com
TURKEY 444 77 11 www.samsung.com
ESTONIA 800-7267 www.samsung.ee
LATVIA 800-7267 www.samsung.com/lv
LITHUANIA 8-800-77777 www.samsung.lt
KAZAHSTAN 8-10-800-500-55-500 www.samsung.kz
KYRGYZSTAN 00-800-500-55-500 RUSSIA 8-800-555-55-55 www.samsung.ru
TADJIKISTAN 8-10-800-500-55-500 UKRAINE 8-800-502-0000 www.samsung.com
UZBEKISTAN 8-10-800-500-55-500 www.samsung.uz
Customer Care Centre
844 000 844 www.samsung.com/cz
Distributor pro Českou republiku:
Samsung Zrt., česka organizační složka Vyskočilova 4, 14000 Praha 4
3260 SAMSUNG (€ 0,15/Min)
08 25 08 65 65 (€ 0,15/Min)
0 801 801 881
022-607-93-33
Web Site
www.samsung.com
www.samsung.com/pl
LCD TV
user manual
BN68-01517A-00
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service, please register
your product at
www.samsung.com/global/register
Model Serial No.
Contact SAMSUNG WORLDWIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG
customer care centre.(See back cover for more information)
Precautions When Displaying a Still Image
A still image may cause permanent damage to the TV screen.
• Do not display a still image on the LCD panel for more than 2 hours as it can cause screen
image retention.
This image retention is also known as "screen burn".
To avoid such image retention, reduce the degree of brightness and contrast of the screen when
displaying a still image.
• Watching the LCD TV in 4:3 format for a long period of time may leave traces of
effect to the screen. Damages caused by the above effect are not covered by the Warranty.
• Displaying still images from Video games and PC for longer than a certain period of time may
produce partial after-images.
To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when displaying still images.
© 2008 Samsung Electronics Co., Ltd. All rights reserved.
borders displayed on the left, right and center of the screen caused by the difference
of light emission on the screen. Playing a DVD or a game console may cause a similar
Contents
CONNECTING AND PREPARING YOUR TV
List of Parts ........................................................ 2
Installing the Stand ............................................. 2
Installing the Wall Mount Kit ............................... 2
Viewing the Control Panel .................................. 3
Viewing the Connection Panel ........................... 4
Viewing the Remote Control ............................... 7
Installing Batteries in the Remote Control .......... 8
Switching On and Off ......................................... 8
Placing Your Television in Standby Mode........... 8
Viewing the Menus ............................................. 9
Using the TOOLS Button .................................... 9
Plug & Play ....................................................... 10
SETTING THE CHANNELS
Storing Channels Automatically ........................11
Storing Channels Manually .............................. 12
Adding / Locking Channels .............................. 13
Sorting the Stored Channels ............................ 14
Assigning Channels Names ............................. 14
Fine Tuning Channel Reception ....................... 15
LNA (Low Noise Amplier) ............................... 15
SETTING THE PICTURE
Changing the Picture Standard ........................ 16
Adjusting the Custom Picture ........................... 17
Resetting the Picture Settings to the Factory
Defaults ............................................................ 17
Changing the Picture Options .......................... 18
SETTING THE SOUND
Sound Features ................................................ 20
Selecting the Sound Mode ............................... 21
SETTING THE TIME
Setting and Displaying the Current Time .......... 22
Setting the Sleep Timer .................................... 22
Switching the Television On and Off
Automatically .................................................... 23
FUNCTION DESCRIPTION
Choosing Your Language ................................. 23
Melody / Energy Saving .................................. 24
Selecting the Source ........................................ 25
Editing the Input Source Names ...................... 26
USING THE DTV FEATURE
Previewing the DTV Menu System .................. 27
Updating the Channel List Automatically .......... 28
Updating the Channel List Manually ................ 28
Editing Your Favourite Channels ...................... 29
Selecting Channel List ..................................... 31
Displaying Programme Information .................. 31
Viewing the EPG (Electronic Programme Guide)
Information ....................................................... 32
Using the Scheduled List ................................. 33
Setting the Default Guide ................................. 33
Viewing All Channels and Favourite Channels 34
Adjusting the Menu Transparency .................... 34
Setting up the Parental Lock ............................ 35
Setting the Subtitle ........................................... 36
Setting the Subtitle Mode ................................. 36
Selecting the Audio Format .............................. 36
Selecting the Audio Description ....................... 37
Selecting the Digital Text (UK only) .................. 37
Selecting the Time Zone (Spain only) .............. 38
Viewing Product Information ............................ 38
Checking the Signal Information ...................... 39
Upgrading the Software ................................... 39
Viewing Common Interface .............................. 40
Selecting the CI (Common Interface) Menu ..... 40
Resetting .......................................................... 41
Selecting the Preferred Language (Subtitle,
Audio or Teletext) ............................................. 41
Preference ........................................................ 42
SETTING THE PC
Setting up Your PC Software
(Based on Windows XP) .................................. 43
Display Modes .................................................. 43
Setting up the TV with your PC ........................ 44
RECOMMENDATIONS FOR USE
Teletext Feature ............................................... 45
Using the Anti-Theft KENSINGTON LOCK
(depending on the model) .....................................46
Troubleshooting: Before Contacting Service
Personnel ......................................................... 47
Technical and Environmental Specications ... 48
English
English - 1
Symbol Press Note One-Touch
Button
List of Parts
Please make sure the following items are included with your LCD TV.
If any items are missing, contact your dealer.
M4XL16
Remote Control
& Batteries
(AAA x 2)
Owner’s Instructions Warranty card Safety Guide Registration Cards
Warranty card / Safety Guide /
➣
The stand and stand screw may not be included depending on the model.
➣
Power Cord Cover-Bottom
Registration Cards (Not available in all locations)
Stand Screw
X 4
Stand Cleaning Cloth
Installing the Stand
2
1
1. Connect your LCD TV and the stand.
Two or more people should carry the TV.
➣
Make sure to distinguish between the front and back of the stand when assembling them.
➣
2. Fasten two screws at position 1 and then fasten two screw at position 2.
Stand the product up and fasten the screws. If you fasten the screws with the LCD TV placed
➣
down, it may lean to one side.
The stand is installed for models with the screen size of 37 inch and above.
➣
Installing the Wall Mount Kit
Wall mount items (sold separately) allow you to mount the TV on
the wall.
For detailed information on installing the wall mount, see the
instructions provided with the Wall Mount items. Contact a
technician for assistance when installing the wall mounted bracket.
Samsung Electronics is not responsible for any damage to the
product or injury to yourself or others if you elect to install the TV on
your own.
Do not install your Wall Mount Kit while your TV is turned
on. It may result in personal injury due to electric shock.
Remove the stand and cover the bottom hole with a
➣
cap and fasten with two screws.
English - 2
Viewing the Control Panel
6 55
The product colour and shape may vary depending on the model.
Side Panel buttons
1
2
3
4
1 SOURCE
Toggles between all the available input
sources (TV, Ext., AV, Component, PC, HDMI1,
HDMI2, DTV). In the on-screen menu, use this
button as you use the ENTER button on the
remote control.
2 MENU
Press to see an on-screen menu of your TV’s
features.
3
Press to decrease or increase the volume.
In the on-screen menu, use the
buttons as you use the ◄ and ► buttons on
the remote control.
4
Press to change channels. In the on-screen
menu, use the buttons as you use
the ▲ and ▼ buttons on the remote control.
(Without the Remote Control, you can turn on
the TV by using the Channel buttons.)
English - 3
5 Speakers
6 (Power)
Press to turn the TV on and off.
Remote Control Sensor
Aim the remote control towards this spot on
the TV.
Power Indicator
Blinks and turns off when the power is on and
lights up in stand-by mode.
Viewing the Connection Panel
5
1
6
8
2
9
0
21 3 5 6
890
!
!
7
7
4
4 3
[TV Rear Panel]
[TV Side Panel]
Power Input
[TV Rear Panel]
[TV Side Panel]
Power Input
The product colour and shape may vary depending on the model.
➣
Whenever you connect an external device to your TV, make sure that power on the unit is turned off.
➣
When connecting an external device, match the colour of the connection terminal to the cable.
➣
English - 4
1 PC IN [PC] / [AUDIO]
Connect to the video and audio output jack on your PC.
-
2 COMPONENT IN
Connect component video cables (optional) to component connector ("PR", "PB", "Y") on the rear of
-
your set and the other ends to corresponding component video out connectors on the DTV or DVD.
If you wish to connect both the Set-Top Box and DTV (or DVD), you should connect the Set-Top Box to
-
the DTV (or DVD) and connect the DTV (or DVD) to component connector ("PR", "PB", "Y") on your set.
The PR, PB and Y connectors on your component devices (DTV or DVD) are sometimes labeled Y, B-Y
-
and R-Y or Y, Cb and Cr.
Connect RCA audio cables (optional) to [R - AUDIO - L] on the rear of your set and the other ends
-
to corresponding audio out connectors on the DTV or DVD.
3 HDMI IN 1, HDMI IN 2
Supports connections between HDMI-connection-enabled AV devices (Set-Top Boxes, DVD players)
-
No additional Audio connection is needed for an HDMI to HDMI connection.
-
When using an HDMI/DVI cable connection, you must use the HDMI IN 2 jack.
-
What is HDMI?
➣
“High Denition Multimedia interface” allows the transmission of high denition digital video data
-
and multiple channels of digital audio.
The HDMI/DVI terminal supports DVI connection to an extended device with the appropriate cable
-
(not supplied). The difference between HDMI and DVI is that the HDMI device is smaller in size, has
the HDCP (High Bandwidth Digital Copy Protection) coding feature installed, and supports
multi - channel digital audio.
DVI IN(HDMI2) [R-AUDIO-L]
DVI audio outputs for external devices.
-
Supported modes for HDMI/DVI and Component
➣
HDMI/DVI 50Hz
HDMI/DVI 60Hz
Component O O O O O O
480i 480p 576i 576p 720p 1080i
X X X O O O
X O X X O O
4 AUDIO OUT [R-AUDIO-L]
Connect RCA audio cables to AUDIO OUT [R-AUDIO-L] on the rear of your set and the other ends
-
to corresponding audio in connectors on the Amplier or DVD Home Theatre.
5 ANT IN
To view television channels correctly, a signal must be received by the set from one of the following
sources:
An outdoor aerial / A cable television network / A satellite network
-
6 SERVICE
Connector for SERVICE only.
-
English - 5
7 COMMON INTERFACE Slot
When CI Card isn’t inserted in some channels, "Scrambled
-
Signal" is displayed on the screen.
The pairing information containing a telephone number, CI Card
-
ID, Host ID and other information will be displayed in about 2~3
minutes. If an error message is displayed, please contact your
service provider.
When the channel information conguration has nished, the
-
message "Updating Completed" is displayed, indicating that
the channel list is now updated.
You must obtain a CI Card from a local cable service provider.
➣
Remove the CI Card by carefully pulling it out with your hands since dropping the CI Card may
cause damage to it.
Insert the CI-Card in the direction marked on it.
➣
The place of the COMMON INTERFACE Slot may be different depending on its model.
➣
8 DIGITAL AUDIO OUT (OPTICAL)
Connect to a Digital Audio Component.
-
When the HDMI IN jacks are connected, the DIGITAL AUDIO OUT (OPTICAL) jack on the TV
➣
outputs 2 channel audio only. If you want to hear 5.1 channel audio, connect the Optical jack on
the DVD player or Cable/Satellite Box directly to an Amplier or Home Theater, not the TV.
9 EXT
Connector
EXT
-Inputs or outputs for external devices, such as VCR, DVD, video game device or video disc players.
0 AV IN [VIDEO]/[R-AUDIO-L]
Connect RCA cable to an appropriate external A/V device such as VCR, DVD or Camcorder.
-
Connect RCA audio cables to [R-AUDIO-L] on your set and the other ends to corresponding audio
-
Video Audio (L/R) RGB Video + Audio (L/R)
Input Output
O O O
Only TV or DTV output is available.
out connectors on the A/V device.
! KENSINGTON LOCK (depending on the model)
The Kensington lock (optional) is a device used to physically x the system when used in a public place.
-
If you want to use a locking device, contact the dealer where you purchased the TV.
-
The location of the kensington lock may be different depending on its model.
-
English - 6
TOOLS
Viewing the Remote Control
1 Television Standby button
2 Selects the TV and DTV
mode directly
3 Number buttons for direct
channel access
4
One/Two-digit channel selection
5 +: Volume increase
: Volume decrease
6 Temporary sound switch-off
7 Use to quickly select
frequently used functions.
8 Use to see information on
the current broadcast
9 Colour buttons :
Use these buttons in the
Channel list, etc.
! Electronic Program Guide
(EPG) display
@ Available source selection
# Previous channel
$ P : Next channel
P : Previous channel
% Returns to the previous
menu
^ Control the cursor in the menu
& Exit the on-screen menu
* Picture size selection
( Displays the main on-screen
menu
) Displays the Channel List on
screen
a Digital subtitle display
Teletext Functions
2 Exit from the teletext display
7 Teletext size selection
8 Teletext reveal
9 Fastext topic selection
0 Alternately select Teletext,
Double, or Mix.
! Teletext store
@ Teletext mode selection
(LIST/FLOF)
# Teletext sub page
$ P : Teletext next page
P : Teletext previous page
% Teletext hold
& Teletext cancel
( Teletext index
The performance of the remote control may be affected by bright light.
➣
English - 7
Installing Batteries in the Remote Control
1. Lift the cover at the back of the remote control upward as shown in the
figure.
2. Install two AAA size batteries.
Make sure to match the "+" and "–" ends of the batteries with the
➣
diagram inside the compartment.
3. Replace the cover.
Remove the batteries and store them in a cool, dry place if you won’t
➣
be using the remote control for a long time.
If the remote control doesn’t work, check the following:
➣
1. Is the TV power on?
2. Are the plus and minus ends of the batteries reversed?
3. Are the batteries drained?
4. Is there a power outage, or is the power cord unplugged?
5. Is there a special uorescent light or neon sign nearby?
Switching On and Off
The mains lead is attached to the rear of your set.
1. Plug the mains lead into an appropriate socket.
The standby indicator lights up on your set.
➣
2. Press the button on your set.
You also can press the POWER button or the TV/DTV button on the remote control to turn
➣
the TV on.
The channel that you were watching last is reselected automatically.
➣
3. Press the numeric button (0~9) or channel up/down ( / ) button on the remote control or
button on your set.
When you switch the set on for the very rst time, you will be asked to choose language in which the
➣
menus are to be displayed.
4. To switch your set off, press the POWER button again.
Placing Your Television in Standby Mode
Your set can be placed in standby mode in order to reduce the power consumption. The standby
mode can be useful when you wish to interrupt viewing temporarily (during a meal, for example).
1. Press the POWER button on the remote control.
The screen is turned off and a red standby indicator appears on your set.
➣
2. To switch your set back on, simply press the POWER , numeric buttons (0~9), TV/DTV button or
channel up/down ( / ) button again.
Do not leave your set in standby mode for long periods of time (when you are away on holiday,
➣
for example).
It is best to unplug the set from the mains and aerial.
English - 8
TOOLS
Viewing the Menus
TOOLS
1. With the power on, press the MENU button.
The main menu appears on the screen. The menu’ s left side
has icons: Picture, Sound, Channel, Setup, Input, Digital Menu.
2. Press the ▲ or ▼ button to select one of the icons.
Then press the ENTER button to access the icon’s sub-
menu.
3. Press the EXIT button to exit.
The on-screen menus disappear from the screen after about
one minute.
Using the TOOLS Button
You can use the TOOLS button to select your frequently used
functions quickly and easily. The “Tools” menu change depending on
which external input mode you are viewing.
1. Press the TOOLS button.
The “Tools” menu will appear.
2. Press the ▲ or ▼ button to select a menu.
3. Press the ▲/▼/◄/►/ENTER buttons to display, change, or
use the selected items. For a more detailed description of each
function, refer to the corresponding page.
• Picture Mode, see page 16
• Sound Mode, see page 20
• Sleep Timer, see page 22
• SRS TS XT, see page 20
• Energy Saving, see page 24
• Dual l-ll, see page 21
• Auto Adjustment, see page 44
TV
Mode : Standard
Backlight 7
Contrast 95
Brightness 45
Sharpness 50
Colour 50
Tint G 50 R 50
Picture Options
Reset : OK
Move Enter Return
Picture Mode ◄ Standard ►
Sound Mode : Custom
Sleep Timer : Off
SRS TS XT : Off
Energy Saving : Off
Dual l-ll : Mono
Move Adjust Exit
Picture
Tools
English - 9
Plug & Play
When the TV is initially powered on, several basic settings
proceed automatically and subsequently. The following
settings are available.
Any functions related to Digital TV (DVB) will only work in
countries or areas where DVB-T (MPEG2) digital terrestrial
signals are broadcasted. Please confirm with your local
dealer if you can receive DVB-T signals. Although this TV set
follows the DVB-T specification, maintaining compatibility with
the future coming DVB-T digital terrestrial broadcasts is not
guaranteed. Several functions may not be available in some countries.
1. Press the POWER button on the remote control.
The message "Start Plug & Play." is displayed with "OK" selected.
2. Select the appropriate language by pressing the ▲ or ▼ button.
Press the ENTER button to confirm your choice.
3. Press the ◄ or ► button to select “Store Demo” or “Home Use”, then the ENTER button.
We recommend setting the TV to "Home Use" mode for the best picture in your home
environment.
"Store Demo" mode is only intended for use in retail environments.
If the unit is accidentally set to “Store Demo” mode and you want to return to “Home Use”
(Standard): Press the Volume button on the TV. When the volume OSD is displayed, press and
hold the MENU button on the TV for 5 seconds
4. The message "Check antenna input." is displayed with "OK" selected.
Press the ENTER button.
Please check that the antenna cable is connected correctly.
5. Select the appropriate country by pressing the ▲ or ▼ button.
Press the ENTER button to confirm your choice.
6. The message “Some DTV functions may not be available. Digital Scan?” is displayed.
Press the ◄ or ► button to select “Yes” or “No”, then press the ENTER button.
Plug & Play
Start Plug & Play.
OK
Enter
Yes
:
First an Analogue TV search is performed and then a Digital TV ch. auto search is performed.
No: Only an Analogue TV search is performed.
This function is supported for all countries except for the following countries: France, Germany,
Italy, Netherlands, Spain, Switzerland, United Kingdom, Austria.
7.
The "Auto Store" menu is displayed with the "Start" selected. Press the
ENTER button.
The channel search will start and end automatically.
The DTV channel scan menu appears and the DTV channel is automatically updated.
If the DTV channel is updated, the Source in the source list of the Input menu is automatically
changed to DTV.
After all the available channels are stored, the "Clock Set" menu appears.
Press the ENTER button at any time to interrupt the memorization process.
For detailed descriptions about DTV channel update, refer to page 28 of this manual.
After all the available digital channels are stored, the screen to select a time zone is displayed
depending on the country.
8. Press the ENTER button.
Select the "Month", "Day", "Year", "Hour", or "Min" by pressing the ◄ or ► button.
Set the "Month", "Day", "Year", "Hour", or "Min" by pressing the ▲ or ▼ button.
You can also set the “Month”, “Day”, “Year”, “Hour” and "Min" by pressing the number buttons on
the remote control.
English - 10
9. Press the ENTER button to confirm your setting. The message “Enjoy your viewing” is displayed.
When you have finished, press the ENTER button.
Even if the ENTER button is not pressed, the message will automatically disappear after
several seconds.
Language
Country
Auto Store
Clock Set
: Select your language.
: Select your country.
: Automatically scans for and stores channels available in the local area.
: Sets the current time for the TV clock.
If you want to reset this feature...
1. Press the MENU button to display the menu.
Press the ▲ or ▼ button to select "Setup" then press the
ENTER button.
TV
Plug & Play
Language : English
Time
Melody : Off
Energy Saving : Off
Setup
2. Press the ENTER button again, to select "Plug & Play".
For further details on setting up options, refer to the page 10.
The “Plug & Play” feature is only available in the TV mode.
➣
Move Enter Return
Storing Channels Automatically
You can scan for the frequency ranges available to you (and
availability depends on your country).
Automatically allocated programme numbers may not correspond
to actual or desired programme numbers. However, you can sort
numbers manually and clear any channels you do not wish to
watch.
TV
Country : United Kingdom
Auto Store
Manual Store
Channel Manager
Sort
Name
Fine Tune
LNA : Off
1. Press the MENU button to display the menu.
Press the ▲ or ▼ button to select "Channel", then press the
ENTER button.
Move Enter Return
2. Press the ENTER button to select "Country".
3. Select the appropriate country by pressing the ▲ or ▼ button.
Press the ENTER button to confirm your choice.
Even though you have changed the country setting in this menu, the country setting for DTV is
➣
not changed. (Refer to page 28)
4. Press the ▲ or ▼ button to select "Auto Store", then press the ENTER button.
5. Press the ENTER button.
The TV will begin memorizing all of the available channels.
➣
Press the ENTER button at any time to interrupt the memorization process and return to the
➣
"Channel" menu.
6. After all the available channels are stored, the "Sort" menu appears. (refer to page 14)
Channel
English - 11
Storing Channels Manually
Not available in DTV or external input mode.
You can store television channels, including those received
via cable networks.
When storing channels manually, you can choose:
♦ Whether or not to store each of the channels found.
♦ The programme number of each stored channel which you wish
TV
Country : United Kingdom
Auto Store
Manual Store
Channel Manager
Sort
Name
Fine Tune
LNA : Off
Channel
to identify.
1. Press the MENU button to display the menu.
Press the ▲ or ▼ button to select "Channel", then press the
ENTER button.
2. Press the ▲ or ▼ button to select "Manual Store", then press
the ENTER button.
3. Select the required option by pressing the ▲ or ▼ button,
Move Enter Return
TV
Programme : P 1
Colour System : Auto
Sound System : BG
Channel : S 6
Search : 140 MHz
Store : ?
Manual Store
then press the ENTER button.
4. When you are satisfied with your setting, press the
ENTER button.
5.
Press the EXIT button to exit.
Move Enter Return
♦ Programme (Programme number to be assigned to a channel)
− Press the ▲ or ▼ button until you find the correct number.
You can also select the channel number directly by pressing the numeric buttons (0~9).
♦ Colour System: Auto/PAL/SECAM/NTSC4.43
− Press the ▲ or ▼ button to select the required colour standard.
♦ Sound System: BG/DK/I/L
− Press the ▲ or ▼ button to select the required sound standard.
♦ Channel (When you know the number of the channel to be stored)
− Press the ▲ or ▼ button to select C (Air channel) or S (Cable channel).
− Press the ► button, then press the ▲ or ▼ button to select the required number.
You can also select the channel number directly by pressing the numeric buttons (0~9).
If there is abnormal sound or no sound, re-select the sound standard required.
♦ Search (When you do not know the channel numbers)
− Press the ▲ or ▼ button to start the search.
− The tuner scans the frequency range until the first channel or the channel that you selected is
received on the screen.
♦ Store (When you store the channel and associated programme number)
− Set to "OK" by pressing the ENTER button.
Channel mode
− P (Programme mode): When completing tuning, the broadcasting stations in your area have been
assigned to position numbers from P00 to P99. You can select a channel by entering the position
number in this mode.
− C (Air channel mode): You can select a channel by entering the assigned number to each air
broadcasting station in this mode.
− S (Cable channel mode): You can select a channel by entering the assigned number for each
cable channel in this mode.
English - 12
Adding / Locking Channels
TOOLS
Not available in DTV or external input mode.
➣
Using the Channel Manager, you can conveniently lock or add
channels.
1. Press the MENU button to display the menu.
Press the ▲ or ▼ button to select "Channel", then press the
ENTER button.
2. Press the ▲ or ▼ button to select "Channel Manager",
then press the ENTER button.
♦ Adding channels
Using the Channel List, you can add channels.
3. Select "Channel List" by pressing the ENTER button.
4. Move to the ( ) field by pressing the ▲, ▼, ◄ or ►
button, select a channel to be added, and press the
ENTER button to add the channel.
If you press the ENTER button again, the ( ) symbol
➣
next to the channel disappears and the channel is not
added.
" " is active when "Child Lock" is selected to "On".
➣
♦ Locking channels
This feature allows you to prevent unauthorized users, such
as children, from watching unsuitable programmes by muting
out video and audio.
5. Press the ▲ or ▼ button to select "Child Lock", then press
the ENTER button.
6. Select "On" by pressing the ▲ or ▼ button, then press the
ENTER button.
7. Press the ▲ or ▼ button to select "Channel List",
then press the ENTER button.
8. Move to the " " field by pressing the ▲, ▼, ◄ or ► button,
select a channel to be locked, and press the ENTER
button.
If you press the ENTER button again, the ( ) symbol
➣
next to the channel disappears and the channel lock is
cancelled.
A blue screen is displayed when "Child Lock" is activated.
➣
9. Press the EXIT button to exit.
Select "On" or "Off" in "Child Lock" to easily turn the
➣
channels which selected on " " to be active or inactive.
TV
Country : United Kingdom
Auto Store
Manual Store
Channel Manager
Sort
Name
Fine Tune
LNA : Off
Move Enter Return
TV
Channel List
Child Lock : Off
Move Enter Return
P 1 C3
Prog.
0 C-1 C3
2 BBC 1
3 C74
4 C75
5 C76
6 S3
7 S4
8 S6
9 S7
Add Lock
Move Enter
Page Return
Channel
Channel Manager
Channel List
1 / 10
You can select these options by simply pressing the CH LIST
button on the remote control.
English - 13
Sorting the Stored Channels
This operation allows you to change the programme numbers
of the stored channels.
This operation may be necessary after using the auto store.
Not available in DTV or external input mode.
➣
1. Press the MENU button to display the menu.
Press the ▲ or ▼ button to select "Channel", then press the
ENTER button.
2. Press the ▲ or ▼ button to select "Sort", then press the
ENTER button.
3. Select the channel number that you wish to change by
pressing the ▲ or ▼ button.
Press the
➣
ENTER
button.
The selected channel number and name are moved to
right side.
4. Select the number of the programme to which the channel is to
be moved by pressing the ▲ or ▼ button.
5. Press the
ENTER
button. The channel is moved to its new
position and all other channels are shifted accordingly.
6. Repeat steps 3 to 5 for another channel to be sorted.
7. Press the EXIT button to exit.
Assigning Channels Names
Channel names will be assigned automatically when channel
information is broadcast. These names can be changed,
allowing you to assign new names.
Not available in DTV or external input mode.
➣
1. Press the MENU button to display the menu.
Press the ▲ or ▼ button to select "Channel", then press the
ENTER button.
2. Press the ▲ or ▼ button to select "Name", then press the
ENTER button.
3. If necessary, select the channel to be assigned to a new
name by pressing the ▲ or ▼ button. Press the ENTER
button.
The selection bar is displayed around the name box.
➣
4.
To...
Select a letter, number or symbol
Move on the next letter
Move back the previous letter
Confirm the name
The following characters are available: Letters of the alphabet (A~Z) / Numbers
➣
(0~9) / Special characters (+, -, *, /, space)
5. Repeat steps 3 to 4 for each channel to be assigned to a new name.
6. Press the EXIT button to exit.
Then...
Press the ▲ or ▼ button
Press the ► button
Press the ◄ button
Press the ENTER button
TV
Country : United Kingdom
Auto Store
Manual Store
Channel Manager
Sort
Name
Fine Tune
LNA : Off
Move Enter Return
TV
Prog. Ch. Name
0 C-- ---- 1 C23 -----
2 S06 ---- 3 S07 ---- 4 S09 ---- 5 S12 ---- 6 S13 ---- 7 S14 ---- 8 S17 ---- 9 C21 -----
Move Enter Return
TV
Country : United Kingdom
Auto Store
Manual Store
Channel Manager
Sort
Name
Fine Tune
LNA : Off
Move Enter Return
TV
Prog. Ch. Name
0 C-- -----
1 C23 -----
2 S06 ---- 3 S07 ---- 4 S09 ---- 5 S12 ---- 6 S13 ---- 7 S14 ---- 8 S17 ---- 9 C21 -----
Move Enter Return
Channel
Channel
Sort
Name
English - 14
Loading...