Samsung 798MBPLUS User Manual

SyncMaster 798MB / 798MBplus

Install drivers Install programs

Notational

Failure to follow directions noted by this symbol could result in bodily harm or damage to
equipment.

Prohibited Important to read and understand at all times

Do not disassemble Disconnect the plug from the outlet

Do not touch Grounding to prevent an electric shock

Power

When not used for extended periods of time, set your computer to a screen
saver.

z

If the same image is present for long periods of time, Phosphor Burnt can be

occured, or the screen may be blurred.

Do not use a damaged or loose plug.

z This may cause an electric shock or fire.

Do not pull the plug out by the wire nor touch the plug with wet hands.

z This may cause an electric shock or fire.

Use only a properly grounded plug and receptacle.

z An improper ground may cause electric shock or equipment damage.

Insert the power plug firmly so that it does not come loose.

Installation

A bad connection may cause fire.

z

Do not excessively bend the plug and wire nor place heavy objects upon
them, which could cause damage.

z This may cause an electric shock or fire.

Do not connect too many extension cords or plugs to an outlet.

z This may cause fire.

Be sure to contact an authorized Service Center when installing your set in a
location with heavy dust, high or low temperatures, high humidity, and chemical
substances, or where it will be operated for 24 hours continuously such as an
airport, train station or etc.

Failure to do so may cause serious damage to your set.

Put your monitor in a location with low humidity and a minimum of dust.

z Failure to do so may cause an electric shock or fire inside the monitor.

Do not drop the monitor when moving it.

z This may cause damage to the product or human body.

Install the monitor base in a showcase or shelf so that the end of the
base does not protrude from the showcase or shelf.

z Dropping the product may cause damage to the product or personal

injury.

Do not place the product on an unstable or small surface area.

z Place the product on an even, stable surface, as the product may fall

and cause harm to someone walking by, specifically children.

Do not place the product on the floor.

z Someone, specifically children could trip over it.

Keep any flammable objects such as candles, insecticides or cigarettes
away from the product.

z Otherwise, this may cause a fire.

Keep any heating devices away from the power cable.

z A melted coating may lead to electric shock or fire.

Do not install the product in places with poor ventilation, for instance, a
bookshelf, closet, etc.

z Any increase in internal temperature may cause fire.

Set down the monitor carefully.

z The monitor could be damaged or broken.

Do not place the monitor face down.

The CDT surface may be damaged.

z

Do not use the monitor without the monitor stand.

z It could break down or cause fire due to bad ventilation.
z If the monitor must be used without the supplied stand, take steps to

insure proper ventilation.

When installing the product, make sure to keep it away from the wall
(more than 10cm/4inch) for ventilation purposes.

z Poor ventilation may cause an increase in the internal temperature of

the product, resulting in a shortened component life and degraded
performance.

Clean

When cleaning the monitor case or the surface of the CDT, wipe with a slightly
moistened, soft fabric.

Do not clean Flat monitor with water. Use a water-diluted mild detergent.

(Some detergents contain significant amounts of alcohol-based solvents, which
can damage (color change) or crack the monitor case. The antiglare/anti-static
surface coating on the CDT may also be affected.)

Dilute the detergent (1:10 ratio) with water before using.

Do not spray water or detergent directly on the monitor.

Use the recommended detergent with a smooth cloth.

z You may prevent the coated CDT from being damaged or the monitor

cabinet from being dissolved, cracked or discolored.

z You may buy a recommended detergent at any Service Center.

If the connector between the plug and the pin is dusty or dirty, clean it
properly with a dry cloth.

z A dirty connector may cause an electric shock or fire.

Make sure to unplug the power cord before cleaning the product.

z Otherwise, this may cause electric shock or fire.

Unplug the power cord from the power outlet and wipe the product using
a soft, dry cloth.

z Do not use any chemicals such as wax, benzene, alcohol, thinners,

insecticide, air freshener, lubricant or detergent.

Contact the Service Center or Customer Center for interior cleaning once
a year.

z Keep the product's interior clean. Dust which has accumulated in the

interior over an extended period of time may cause malfunction or fire.

Others

Do not remove cover(or back).

z This may cause an electric shock or fire.
z Refer servicing to qualified service personnel.

If your monitor does not operate normally - in particular, if there are any
unusual sounds or smells coming from it - unplug it immediately and

contact an authorized dealer or service

z This may cause an electric shock or fire.

.

Keep the product away from places exposed to oil, smoke or moisture;
do not install inside a vehicle.

z This may cause malfunction, an electric shock or fire.
z Especially avoid operating the monitor near water or outdoors where the

monitor could be exposed to snow or rain.

If the monitor is dropped or the casing is damaged, turn the monitor off
and unplug the power cord. Then contact the Service Center.

z The monitor may malfunction, causing an electric shock or fire.

Disconnect the plug from the outlet during storms or lightening or if it is
not used for a long period of time.

z Failure to do so may cause an electric shock or fire.

Do not try to move the monitor by pulling only the wire or the signal
cable.

z This may cause a breakdown, electric shock or fire due to damage to the

cable.

Do not move the monitor right or left by pulling only the wire or the
signal cable.

This may cause a breakdown, electric shock or fire due to damage to the

z

cable.

Do not cover the vents on the monitor cabinet.

z Bad ventilation may cause a breakdown or fire.

Do not place water containers, chemical products or small metal objects
on the monitor.

z This may cause malfunction, an electric shock or fire.
z If a foreign substance enters the monitor, unplug the power cord and

contact the Service Center .

Do not place any heavy objects on the monitor.

z This may cause an electric shock or fire.

Keep the product away from combustible chemical sprays or
inflammable substances.

z This may cause an explosion or fire.

Never insert anything metallic into the monitor openings.

z This may cause an electric shock, fire or injury.

Keep the monitor away from any magnetic substances.

z This may cause discoloring or distortion of the image.

Watching the monitor continuously at a too close angle may result in
eyesight damage.

To ease eye strain, take at least a five-minute break after every hour of
using the monitor.

Do not install the product on an unstable, uneven surface or a location
prone to vibrations.

z Dropping the product may cause damage to the product or personal

injury. Using the product in a location prone to vibrations may shorten
the lifetime of the product or may catch fire.

When moving the monitor, turn off and unplug the power cord.
Make sure that all cables, including the antenna cable and cables
connected to other devices, are disconnected before moving the
monitor.

z Failure to disconnect a cable may damage it and lead to fire or an

electric shock.

Place the product out of children's reach, as they could damage it by
hanging onto it.

z A falling product could cause physical damage even death.

When not using the product for an extended time period, keep the
product unplugged

z Otherwise, this may cause heat emission from the accumulated dirt or

degraded insulation, leading to electric shock or fire.

Do not place children's favorite objects (or anything else that may be
tempting) on the product.

z Children may try to climb on the product to retrieve an object. The

product could fall, causing physical damage or even death.

Unpacking

Monitor and Stand

Please make sure the following items are included with your monitor.

If any items are missing, contact your dealer.

(Some models include a stand attached.)

Manual

Cable

Quick Setup Guide

Warranty Card

(Not available in all

locations)

User's Guide,

Monitor Driver,

Natural Color software,

MagicTune™ software,

Highlight Zone III 3.5

software

)

Power Cord

Stand

Stand

For Multimedia model (Option)

Manual

User Guide

Cable

Sound Cables(2each

DC Power Cord

Stand

Multimedia Speaker Stand

Front

MENU button

Adjust buttons [ ]

Enter button [ ]

Opens the OSD menu. Also used to exit the OSD menu or
return to the previous menu.

These buttons allow you to highlight and adjust items in the
menu.

Used to select the OSD menu.

Power button[ ]

Power indicator

See PowerSaver described in the manual for further information regarding power saving
functions. For energy conservation, turn your monitor OFF when it is not needed, or when
leaving it unattended for long periods.

Rear

Use this button for turn the monitor on and off.

This light glows green during normal operation, and blinks green
once as the monitor saves your adjustments.

(The configuration at the back of the monitor may vary from product to product.)

Power port

Signal Cable

See Connecting the Monitor for further information regarding cable connections.

Connect the power cord for your monitor to the power port on

the back of the monitor.

Connect the signal cable to the video port on your computer.
(video board, video card, or graphics card)

Bottom

Tilt/Swivel Base

You can separate the base from the monitor.

Connecting the Monitor

Setup-For Multimedia model | Multimedia Speaker Stand

1.

2-1.

2-2.

2-3.

3.

Connect the power cord for your monitor to the power port on the back of the monitor.
Plug the power cord for the monitor into a nearby outlet.

Connecting to a computer
Connect the signal cable to the 15-pin, D-sub connector on the back of your computer.

Connecting to a new Macintosh
Connect the monitor to the Macintosh computer using the D-SUB connection cable.

Connecting to an old Macintosh
Connect your monitor to the Macintosh using the adapter for Macintosh (sold separately).

Turn on your computer and monitor. If your monitor displays an image, installation is
complete.

Setup-For Multimedia model

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

Turn off your computer and unplug the power cord.

Connect the end of the signal cable to your computer's video port(video board, video card or
graphics card).

Connect one end of the other sound cable to the Mic Input jack on your sound card or
computer.Connect the other end of this cable to the Mic By-pass jack on the back of the
monitor stand.

Plug the DC power cord from the stand into a nearby outlet.

Connect the power cord for your monitor to the power port on the back of the monitor.

Plug the power cord for the monitor and the power cord for your computer into a nearby
outlet.

Turn on your computer and monitor.

Turn up or down the On-Off control terminal on the stand of the monitor until it clicks.

Execute a sound program, music or sound effect in your computer and then adjust the volume
by turning up or down until the sound volume is appropriate.

Adjust the treble and bass.

Sound distortion may occur when the monitor is placed on top of a mostly hollow cabinet
such as your computer. If this occurs, place a pad or magazine beneath the monitor stand.
High sound volume may also cause sound distortion; lower the volume.

Multimedia Speaker Stand

1. Mic By-pass Jack

To transmit your voice,connect a sound cable from
the Mic By-pass jack to the mic in jack on the sound
card slot in your computer.

2. Stereo Input Jack

Connect a sound cable from the input source(sound
card,computer,CD-ROM drive).

3. DC Power Cord

g

y

Connect DC power cord to monitor DC 12V output
jack.

4. Power Indicator

Glows green when the speakers are turned on.

5. On/Off Volume

Turns On/Off and adjusts the output volume.

6. Treble Control

Use to control high frequencies.

7. Bass Control

Use to control low frequencies.

8. Mic Input Jack

To transmit your voice,connect a microphone to this
jack.

9. Headphone Jack

To listen in privacy,connect headphones here.

10.
Detachable Stand Top

Base Installation

Tilt/Swivel Base

With the built-in pedestal, you can tilt and/or swivel the monitor for the most comfortable
viewin

angle.

Tilt/Swivel Base | Attaching and Removing the Base

The base is detachable.

Attaching and Removing the Base

our monitor was supplied with the base detached, attach the base as follows.

If

g

g

Remove the twist-tie before attaching the base to the monitor.

Attachin

1. Place the monitor upside-down on a flat work surface.

2. Align the tabs on the base with the corresponding slots on the bottom of the monitor.

3. Press the base onto the monitor until the tabs are fully engaged in the slots.

4. Push the base toward the front of the monitor until the release latch clicks into the locked

Removin

5. Squeeze and pull up on the release latch on the base.

6. Push the base toward the back of the monitor and lift up to remove the base.

the Base

position.
* Do not bend the snap.

the Base

The base will align with the monitor slots in only one position.

Installing the Monitor Driver(Automatic)

When prompted by the operating system for the monitor driver, insert the CD-ROM

included with this monitor. Driver installation is slightly different from one operating
system to another. Follow the directions appropriate for the operating system you
have.

Prepare a blank disk and download the driver program file at the Internet web site shown
here.

z Internet web site : http://www.samsung.com/ (Worldwide)

http://www.samsung.com/monitor (U.S.A)
http://www.sec.co.kr/monitor (Korea)

http://www.samsungmonitor.com.cn/ (China)

Windows ME

1. Insert CD into the CD-ROM drive.

2. Click

"Windows ME Driver"

.

3. Choose your monitor model in the model list, then click the

"OK"

button.

4. Click the

5. Monitor driver installation is completed.

Windows XP/2000

1. Insert CD into the CD-ROM drive.

2. Click

3. Choose your monitor model in the model list, then click the

"Install"

button in the

"Windows XP/2000 Driver"

"Warning"

window.

"OK"

button.

4. If you can see following message window, then click the
Then click

"OK"

button.

"Continue Anyway"

button.

This monitor driver is under certified MS logo and this installation doesn't
damage your system. The certified driver will be posted on Samsung
Monitor homepage.

http://www.samsung.com/.

5. Monitor driver installation is completed.

Installing the Monitor Driver(Manual)

Windows XP | Windows 2000 | Windows Me | Windows NT | Linux

When prompted by the operating system for the monitor driver, insert the CD-ROM
included with this monitor. Driver installation is slightly different from one operating
system to another. Follow the directions appropriate for the operating system you
have.

Prepare a blank disk and download the driver program file at the Internet web site shown
here.

z Internet web site : http://www.samsung.com/ (Worldwide)

http://www.samsung.com/monitor (U.S.A)
http://www.sec.co.kr/monitor (Korea)

http://www.samsungmonitor.com.cn/ (China)

Microsoft® Windows® XP Operating System

1. Insert CD into the CD-ROM driver.

2. Click "

Start

" —> "

Control Panel

" then click the "

3. Click "

Display

" icon and choose the "

Appearance and Themes

Settings

" tab then click "

Advanced..

".

" icon.

4. Click the "

Properties

" button on the "

Monitor

" tab and select "

Driver

" tab.

5. Click "

6. Select "

Update Driver..

Don't search ,I will..

" and select "

Install from a list or..

" then click "

Next

" then click "

" and then click "

Have disk

Next

" button.

".

7. Click the "
model list and click the "

Browse

" button then choose A:(D:\Driver) and choose your monitor model in the

" button.

Next

K

8. If you can see following message window, then click the "
click "OK" button.

This monitor driver is under certified MS logo and this installation doesn't
damage your system. The certified driver will be posted on Samsung
Monitor homepage.

http://www.samsung.com/.

9. Click the "

" button, then click "OK" button continually.

Close

Continue Anyway

" button. Then

10. Monitor driver installation is completed.

Microsoft

®

Windows® 2000 Operating System

When you can see "Digital Signature Not Found" on your monitor, follow these steps.

1. Choose "OK" button on the "

2. Click the "

Browse

" button on the "

Insert disk

" window.

File Needed

" window.

3. Choose A:(D:\Driver) then click the "Open" button and then click "

" button.

O

How to install

1. Click "

2. Double click the "

3. Choose the "

4. Choose "

Case1:If the "Properties" button is inactive, it means your monitor is properly configured.

Case2:If the "Properties" button is active, click the "Properties" button then follow next steps

5. Click "

6. Choose "

specific driver

7. Click the "

8. Click the "

9. Choose your monitor model and click the "

10. Click the "

" , "

Start

Driver

Setting

Settings

Monitor

Please stop installation

continually.

" and then click on "

Display a list of the known drivers for this device so that I can choose a

Browse
Open

Finish

" , "

Control Panel

Display

".

" then click "

" button, then click "OK" button.

" button then the "

" Icon.

" tab and then click "

Update Driver..

" and then click "

" button then choose A:(D:\Driver).

Next

Close

".

Advanced..

Next

" button.

".

" then click on the "Next" button.

Have disk

" button then click "

".

Next

" button.

If you can see the "
And click the "

Microsoft® Windows® Millennium Operating System

1. Click "

2. Double click "

3. Select the "

4. Select the "

5. Click the "

6. Choose "

7. Choose "

8. Click the "

9. Specify A:\(D:\driver) then click "OK" button.

10. Select "
connected to your computer and click "OK".

11. Continue choosing "
dialogue box.

Microsoft® Windows® NT Operating System

1. Click

2. In Display Registration Information window, click Settings Tab and then click

Modes

3. Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency)
and then click OK.

4. Click
not normal, change to a different mode (lower mode of resolution, colors or frequency).

Linux Operating System

To execute X-Window, you need to make the X86Config file, which is a type of system setting file.

1. Press Enter at the first and the second screen after executing the X86Config file.

2. The third screen is for

3. Set a mouse for your computer.

4. The next screen is for

5. Set a Keyboard for your computer.

6. The next screen is for

7. First of all, set a
directly.)

8. Set a

9. Enter the
of X-Window.

10. You have

Execute

" , "

Start

Settings
Monitor

Change
Specify the location of the driver
Display a list of all the driver in a specific location..

Have Disk

Show all devices

Start, Settings, Control Panel

.

Apply

If there is no Mode at
frequency by referring to the Preset Timing Modes in the user guide.

vertical frequency

model name of your monitor

finished

X-Window after setting other requested hardware.

Digital Signature Not Found

" button then the "

Finish

Setting

Display

button if you see the screen working normally after clicking

" , "

Control Panel

" icon.

" tab and click "

" tab.

" button in the "

" button

" and choose the monitor that corresponds to the one you

" button and "OK" button until you close the Display Properties

Close

All Display Modes

setting your mouse

selecting a keyboard

setting your monitor

horizontal frequency

for your monitor. (You can enter the frequency directly.)

setting up your monitor.

Close

".

Advanced Properties

Monitor Type

, and then double-click

for your monitor. (You can enter the frequency

. This information will not affect the actual execution

" window then click the "

" button.

" button.

" area.

".

" then click "

Display

, select the level of resolution and vertical

.

.

.

Yes

icon.

Test

"button.

" button.

Next

All Display

. If the screen is

[

]

Natural Color

Natural Color Software Program

One of the recent problems in using a computer is that the color of the images printed out by a
printer or other images scanned by a scanner or a digital camera are not the same as those
shown on the monitor.
The Natural Color S/W is the very solution for this problem. It is a color administration system
developed by Samsung Electronics in association with Korea Electronics &
Telecommunications Research Institute (ETRI).
This system is available only for Samsung monitors and makes the color of the images on the
monitor the same as the printed or scanned images.
For more information, refer to Help (F1) in the software program.

How to install the Natural Color software

Insert the CD included with the Samsung monitor into the CD-ROM Drive. Then, the initial
screen of the program Natural Color will be executed. Click Natural Color on the initial screen
to install the Natural Color software.
To install the program manually, insert the CD included with the Samsung monitor into the CD­ROM Drive, click the
Enter D:\color\eng\setup.exe and then press the
(If the drive where the CD is inserted is not D:\, enter the applicable drive.)

How to delete the Natural Color software program

Select

[Setting]/[Control Panel]

program]

Select Natural Color from the list and then click the

.

button of Windows and then select

[Start]

on the

<Enter>

menu and then double-click

[Start]

key.

Add/Delete

[Execute]

button.

.

[Add/Delete a

Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu.

These buttons allow you to highlight and adjust items in the menu.

Use to select the OSD menu.

MagicBright2™ is a new feature providing optimum viewing environment depending on the
contents of the image you are watching.

The Highlight Zone ensures clear images on TVs, video conferencing systems or photos by
emphasizing a certain area on the screen.

Brightness

Menu Description

When OSD is not on the screen, push the button to adjust brightness.

MagicBright2™

Menu Description

MagicBright2™

Then push the MagicBright2™ button again to circle through available
preconfigured modes.

Highlight III

Menu Description

The Highlight Zone ensures the clear and sharp display of animated

Highlight III

Select an icon that you want to know from the OSD menu to display a text or animation
explanation of that icon.

multimedia or photo images by enhancing the brightness of a certain area on
the screen.

Menu Description Play/Stop

You can use the on-screen menus to change the brightness
according to personal preference.

Direct Access Feature

push the button to adjust brightness.

You can use the on-screen menus to change the contrast
according to personal preference.

A "Moiré" pattern can appear on your screen, looking like a
series of concentric circles or arcs. To eliminate this pattern,
use the horizontal moire adjustments.

A "Moiré" pattern can appear on your screen, looking like a
series of concentric circles or arcs. To eliminate this pattern,
use the vertical moire adjustments.

The Degauss feature will remove color impurities caused by
magnetic fields.

Use the recall feature to reset these monitor settings to their
original levels: Position, Size, Pincushion, Trapezoid,
Parallelogram, Pinbalance, Rotation, H-Moire,and V-Moire.

If you have selected "Yes", all settings listed above will

Note:

be reset. All other settings will remain the same.

: When OSD is not on the screen,

Menu Description Play/Stop

Color temperature is a measure of the 'warmth' of the image
colors. (6500k / 9300k)

Use to adjust the monitor color setting.(Red)

Use to adjust the monitor color setting.(Green)

Use to adjust the monitor color setting.(Blue)

Standard Red Green Blue (sRGB) is a defined default color
space. If a monitor, printer and scanner are all calibrated to
the sRGB color characteristics, then you can find color
matching from each peripheral. When the monitor is in the
sRGB mode, Brightness / Contrast / MagicBright2™ /
Highlight III adjustment is not available.

Menu Description Play/Stop

Follow these instructions to change the horizontal position of
the monitor's entire display.

Follow these instructions to change the vetical position of the
monitor's entire display.

Follow these instructions to change the horizontal size of the
monitor's entire display.

Follow these instructions to change the vertical size of the
monitor's entire display.

Adjust the pincushion setting when the sides of the display
are bowed in or bowed out.

Adjust the pinbalance setting when the sides of the display
are bowed towards the left or right.

Adjust the trapezoid setting when the top or bottom of the
display is too large or small.

Adjust the parallelogram setting when the display is leaning
left or right.

Adjust the rotation setting when the entire display is tilted left

or right.

OSD Description Play / Stop

Use to turn the Highlight Zone features on or off.

: When "OFF" is selected, the user cannot choose any

Note

other Highlight Zone features.

This function is to move the Highlight Zone horizontally.

This function is to move the Highlight Zone vertically.

This function is to adjust the horizontal size of the Highlight
Zone.

This function is to adjust the vertical size of the Highlight
Zone.

This function is to execute the Highlight Zone.

This function is to use the contrast of the Highlight Zone.

This function is to adjust the sharpness of the Highlight Zone.

You can see the frequency (user control mode) used by the user, the polarity of the operational
signals, the default frequency (default mode) set when you buy the monitor and the resolution
level.

: These screens do not allow any changes to the settings, they are for information only.

Note

Overview | Installation | OSD Mode | Uninstall | Troubleshooting

Overview

What is MagicTune™?

Monitor performance can vary due to the graphics card, host computer lighting conditions and other
environmental factors. In order to get the best image on a monitor requires you to adjust it for your unique
setting. Unfortunately, the manual controls available to tune the image often prove to be challenging. Proper
adjustment (tuning) requires an easy to use program that goes through a step-by-step process to obtain the
best overall picture quality.

In most cases even simple adjustments to Brightness, or Contrast require navigation of the multi-level, on­screen display (OSD) menus that are not easy to understand. Furthermore, there is no feedback to assist in
correctly setting the controls of the monitor. MagicTune is a software utility that guides you through the tuning
process with easy to understand instructions and back ground patterns designed for each monitor control. The
display settings for each user can be saved, providing an easy way to select display characteristics in a multi­user environme or having a single user have multiple defined presets based on content and ambient lighting.

Basic Functionality

MagicTune is a software utility that allows monitor adjustment and color tuning using the Display Data

Channel Command Interface (DDC/CI)

to eliminate the need to use the monitor on-screen display (OSD).
MagicTune supports Windows™ 98 SE, Me, 2000, XP Home, and XP Professional.

It is recommended using MagicTune in Windows™ 2000 or later.

MagicTune allows for quick accurate tuning of the display with the ability to easily save and use monitor
configurations that are best suited for you.

protocol. All adjustments to the display are controlled via software

OSD Mode

The OSD mode allows easy adjustment of monitor settings without taking pre-defined steps. You can access the
desired menu item to set with ease.

Overview | Installation | OSD Mode | Uninstall | Troubleshooting

Installation

1. Insert the installation CD into the CD-ROM drive.

2. Click the MagicTune™ installation file.

3. Select installation Language, Click "Next".

4. When the InstallationShield Wizard window appears, click "Next."

5. Select "I agree to the terms of the license agreement" to accept the terms of use.

6. Choose a folder to install the MagicTune program.

7. Click "Install."

8. The "Installation Status" window appears.

9. Click "Finish."

10. When the installation is complete, the MagicTune executable icon appears on your desktop.

Double-click the icon to start the program.

Magictune execution icon may not appear depending on specification of computer
system or monitor. If that happens, press F5 Key.

Installation Problems

The installation of MagicTune™ can be affected by such factors as the video card, motherboard and the network
environment.

"Troubleshooting" if you have trouble during installation.

See

System Requirements

OS

z

Windows™ 98 SE

z

Windows™ Me

z Windows™ 2000
z Windows™ XP Home Edition

z

Windows™ XP Professional

Hardware

z 32MB Memory above

z

25MB Hard disk space above

It is recommended using MagicTune in Windows™ 2000 or later.

* For more information, visit the MagicTune

website.

Overview | Installation | OSD Mode | Uninstall | Troubleshooting

MagicTune allows for quick accurate tuning of the display with the ability to easily
save and use monitor configurations that are best suited for you.

z OSD mode may appear inconsistent with the explanation in

z MagicTune control mode will be different according to monitor models.

guidance book depending on specification of each monitor.

OSD Mode

The OSD mode makes the adjustment of settings on all monitors easy. When selected , each tab on top of the
control window displays the general descriptions of the sub-menu items for adjustment.
When selected, each tab displays a list of menus. For quick adjustment of the monitor settings, the OSD mode
allows easy and convenient access to all tabs and sub-menu items.

Button Tab Definition

OK

Reset

Cancel

Applies any changes made and exits MagicTune.

Restores the display settings to the factory settings.

Exits MagicTune without applying the changes made. If you have not made any changes
in the control window, clicking "Cancel" does not cause any actions.

Picture Tab Definition

Allows the user to adjust the screen settings to the desired values.

Brightness Contrast MagicBright

nmlkji nmlkj nmlkj

Brightness

Contrast

MagicBright™

Makes the entire screen brighter or darker. The detailed data of the images in the dark
areas can be lost if the brightness is not adjusted to the proper level. Adjust the
brightness for best viewing conditions.

Adjusts the difference in brightness between the bright and dark areas on screen.
Determines the crispness of the images.

MagicBright™ is a new feature providing the optimum viewing environment depending on
the contents of the image you are watching. Currently four different mod es are available:
Text, Internet,Game, Sport, Movie and Custom. Each mode has its own pre-configured
brightness value. You can easily select one of six settings by simply pressing MagicBright
control buttons.

z 19" or above

1. Text: For documentations or works involving heavy text.

2. Internet: For working with a mixture of images such as text and graphics.

3. Game: For watching motion pictures such as a Game.

4. Entertain: For watching motion pictures such as a DVD or VCD.

z

Less than 19"

1. Text: For documentations or works involving heavy text.

2. Internet: For working with a mixture of images such as text and graphics.

3. Entertain: For watching motion pictures such as a DVD or VCD.

Color Tab Definition

Adjusts the "warmth" of the monitor background or image color.

Color Tone Color Control

nmlkji nmlkj

The tone of the color can be changed.

z

Color Tone

5000K - 6500K - 9300K

z Reset

Adjusts of the monitor image color.

Color Control

You can change the monitor color to your desired color.

z

R- G - B

z sRGB

Image Tab Definition

Adjusts the Position, Size and Rotation values.

Geometry 1

Rotation Size Position

nmlkji nmlkj nmlkj

Geometry 2

Pincushion Pinbalance Trapezoid Parallelogram

nmlkj nmlkj nmlkj nmlkj

Other

Moire Degauss Sidepin Corner Top Sidepin Corner Bottom

nmlkj nmlkj nmlkj nmlkj

Pinbalance Corner Top Pinbalance Corner Bottom

nmlkj nmlkj

Adjusts the Position, Size and Rotation values.

Geometry 1

z Position

z

Size

z Rotation

Adjusts the Pincushion, Pinbalance, Trapezoid and Parallelogram values.

Geometry 2

z

Pincushion

z

Pinbalance

z Trapezoid

z

Parallelogram

Adjusts the Moire, Degauss, Sidepin Corner, and Pinbalance Corner values.

z

Other

Moire

z Degauss

z

Sidepin Corner Top

z

Sidepin Corner Bottom

z Pinbalance Corner Top

z

Pinbalance Corner Bottom

Option Tab Definition

You can configure MagicTune using the following options.

Loads the Preferences Dialog Box. Preferences in use will have an "V" in the check box. To
turn on or off any Preference, position the cursor over the box and click.

Preferences

z

Enable task tray menu .

- To access the MagicTune menus, click the icon on the [task tray menu].
The menus are not displayed if the [Enable System Tray] is deselected in
[Options] ' [Basic Settings].

z Select Language - The language chosen affects only the language of the OSD.

Support Tab Definition

Shows the Asset ID and the version number of the program, and allows you to use the Help feature.

Help

Asset ID

Visit the MagicTune website or click to open the Help files (User Manual) if you need any
help installing or running MagicTune. The User Manual opens within a basic browser
window.

you can use the server to control the Client monitor.
(Server program should be installed to use this program as Client)

User Name

Shows the user name that is registered in PC.

User ID

Server IP

Department

Location

Version

Displays the version of MagicTune.

Shows the user ID that is register in PC.

Write down the server IP .

Write down the department.

Write down the location.

Overview | Installation | OSD Mode | Uninstall | Troubleshooting

Uninstall

The MagicTune program can be removed only by using the "Add or Remove Programs" option of the
Windows™ Control Panel.

Perform the following steps remove MagicTune.

1. Go to [Task Tray] ' [Start] ' [Settings] and select [Control Panel] in the menu. If the program runs on
Windows™ XP, go to [Control Panel] in the [Start] menu.

2. Click the "Add or Remove Programs" icon in Control Panel.

3. In the "Add or Remove Programs" screen, scroll down to find "MagicTune." Click on it to highlight it.

4. Click the "Change/Remove" button to remove the program.

5. Click "Yes" to begin the uninstall process.

6. Wait until the "Uninstall Complete" dialog box appears.

website

Visit the MagicTune
software upgrades.

for technical support for MagicTune, FAQs (questions and answers) and

Overview | Installation | OSD Mode | Uninstall | Troubleshooting

Troubleshooting

The current computing system is not compatible with MagicTune.

Please press OK and click on the "Shortcut to the MagicTune site" to view our home page

for further reference.

An error may occur when your video/graphic card is not in the 'Available' list.

(The latest or oldest video cards may not be compatible.)

Please visit our homepage to see the Troubleshooting section.

An error may occur if the card maker has modified the video card driver or the

graphics chip even when the video card is in the list.

Please visit our homepage to see the Troubleshooting section.

Check if your monitor is manufactured by Samsung.

Products from other manufacturers may cause errors.

Only Samsung products are able to support this feature.

An error may occur even when your monitor is manufactured by Samsung but is

out of date.

Check if your monitor is able to support MagicTune.

This feature is only supported by those monitors that are registered on our homepage.

Check for the monitor before purchasing it as out-of-date models are not supported.

An error occurs when no information on EDID (Extended Display Identification

Data) exists for the current monitor.

This happens when from your desktop, Start > Setup > Control Panel > System >

Hardware > Device Manager > Monitor is selected, the current "Plug-and-play

monitor" is removed and new hardware is searched for but the system couldn't find

any "Plug-and-play monitor".

Please visit our homepage to see the Troubleshooting section.

An error occurs when replacing the monitor with a new one when the system

power is off but the system has not been restarted.

Please restart the system each time the monitor is replaced before using MagicTune.

An error occurs when the video card driver is not installed properly.

This happens when the current video card list is not displayed normally. You can

check this via Start > Setup > System > Hardware > Device Manager > Display

Adapter.

Visit the video card maker's homepage and download and install the latest driver.

For more information about the video card, contact the card manufacturer.

To ensure normal operation, please restart your system.

An error occurs when the system is not restarted after installing MagicTune.

(This is for Win98SE and WinMe only.)

Restart the system before use.

For the best performance of MagicTune, adjust to the optimal resolution. Refer to the User

Guide for the optimal resolution.

If you do not adjust to the optimal resolution and perform Color Calibration, the

monitor cannot be adjusted to the optimal condition.

Refer to the manual for the optimal resolution.

This video card does not support MagicTune.

Please install a new video card driver.

An error occurs when the video card driver is not installed properly.

This happens when the current video card list is not displayed normally. You can

check this from Start > Setup > System > Hardware > Device Manager > Display

Adapter.

Visit the video card manufacturer's homepage and download and install the latest

driver.

For more information about the video card, contact the card manufacturer.

As the Highlight program uses the communication lines,

please exit the Highlight program before you can access MagicTune.

Some of Samsung CDT monitors support the Highlight feature.

When using both the Highlight feature and MagicTune simultaneously, conflicts

occur, which cause errors.

Make sure to turn OFF Highlight before using MagicTune.

Troubleshooting

z

MagicTune may not work in case monitor is replaced or driver of graphic card is updated while
MagicTune is operating. If so, please restart the system.

Symptom Check List Solutions

Check when
MagicTune does not
function properly.

MagicTune feature is found
only on PC (VGA) with
Window OS that supports
Plug and Play.

* To check whether your PC is available for
MagicTune feature, follow the
steps below (When Windows™ is XP);

Control Panel -> Performance and Maintenance

-> System -> Hardware -> Device Manager ->
Monitors -> After deleting Plug and Play
monitor, find 'Plug and Play monitor' by
searching new Hardware.

MagicTune is an additional software for the
monitor. Some graphic cards may not support
your monitor. When you have a problem with

the graphic card, visit our website to check the
compatible graphic card list provided.

http://www.samsung.com/monitor/magictune

MagicTune™ doesn't
work properly.

Have you changed your PC
or video graphic card?

Download the latest program. The program can
be downloaded

http://www.samsung.com/monitor/magictune.

z Visit the MagicTune website for technical support for MagicTune, FAQs (questions and answers) and

software upgrades.

z

Visit the MagicTune

website

and download the installation software for MagicTune MAC.

The Highlight Zone ensures the clear and sharp display
of animated multimedia or photo images by enhancing
the brightness of a certain area on the screen.

Highlight Zone III features a combination of the circuitry
and the program built on the proprietary technology of
SEC.

This offers an easy-to-use interface that highlights the
video-playing portion of your multimedia program by
automatically detecting and highlight the desired area
by dragging.

The Highlight Zone provides optimal display of moving
pictures. So, text may appear blurry in the Highlight
Zone.

Automatic detect

Manual detect

Exit Program

Auto Detect

Picture Setting

Full Screen

Highlight Off

Other Features

g

Automatic detect

Manual detect

Exit Program
Auto Detect
Picture Setting
Full Screen
Highlight Off

Other Features

Automatic detect

1. When the Highlight program is running, the monitor automatically detects the video-playing portion of your multimedia program and activates the
Highlight Zone feature. No selection is necessary.

Major multimedia programs: Windows Media Player, RealPlayer 8.0, video players on the broadcasters¡¯ websites, etc.
However, Automatic Detect may not work with a DVD player. (In this case, change the setting to Manual Detect mode to create a Highlight Zone.)
Select 'Off' in Auto Detect menu when you wish to deactivate the Automatic Detect feature.
Since this disables the Auto Detect capability of the monitor, the monitor does not automatically create a Highlight Zone.
(When you first install the program, Automatic Detect is set to 'On'.)

Note 1 : When OSD is selected while the Auto Detect is running, Highlight Zone turns off temporarily not to disturb adjustment of display conditions

such as bri

htness and color.

(

)

g

(

)

(

)

Automatic detect

Manual detect

Exit Program

Auto Detect

Picture Setting

Full Screen

Highlight Off

Other Features

Manual detect

In Manual Detect mode, you can either select a window or use the Drag function to create a Highlight Zone.

1. Selecting a window: Click the Highlight icon( )on the Windows taskbar once to activate( )the cursor.
Move the cursor onto the window of your choice and click once to Highlight the window.

2. Drag: Click the Highlight icon( )on the Windows taskbar once to activate( )the cursor.
Click and hold the left mouse button, then drag the cursor to create a rectangle that covers the desired area. This rectangle becomes the Highlight Zone.

Note 1 :

When the mouse cursor is activated( )and it is necessary to de-activate it to use it for other tasks, right click your mouse,
or put the activated cursor

Note 2 :

You can determine whether the Hi

Note 3 : When OSD is selected while the Manual Detect is running, Highlight Zone turns off temporarily, as it does when Auto detect is running.

on the taskbar and click. When de-activated, the icon on the screen changes back to the one shown before activation.

hlight feature is on/off by the appearance of the icon on the taskbar. On

, Off

g

Exit Program

1. Exits the Hi

hlight program.

Automatic detect

Manual detect

Exit Program

Auto Detect

Picture Setting

Full Screen

Highlight Off

Other Features

(V)

Automatic detect

Manual detect

Exit Program

Auto Detect

Picture Setting

Full Screen

Highlight Off

Other Features

Auto Detect

1. Allows user to disable Auto Detect when necessary.
Once selected, this function saves the selection and keeps it in the memory regardless of exiting or restarting the program.
When selected, a check mark

appears.

ging

Automatic detect

Manual detect

Exit Program

Auto Detect

Picture Setting

Full Screen

Highlight Off

Other Features

Picture Setting

1. Can be selected only when the Highlight Zone function is on. When selected, a menu window appears which can be used to adjust Contrast
and Sharpness within the Highlight Zone.
After chan

the setting, select OK to save the changes, or Cancel to return to the previous setting.

g

(

)

Full Screen

1. Full Screen: Place the cursor on the Hi

hlight icon

Automatic detect

Manual detect

Exit Program

Auto Detect

Picture Setting

Full Screen

Highlight Off

Other Features

on the Windows taskbar and right click your mouse once. Then select Full Screen from the menu.

g

Highlight Off

1. Cancels the selection of a Hi

hlight Zone and reverts to the original screen.

Automatic detect

Manual detect

Exit Program

Auto Detect

Picture Setting

Full Screen

Highlight Off

Other Features

y

(

)

Automatic detect

Manual detect

Exit Program

Auto Detect

Picture Setting

Full Screen

Highlight Off

Other Features

Other Features

The Highlight Zone function remembers the variables of the selected areas in Automatic and Manual Detect modes, respectively.

1. If the window selected as a Highlight Zone is moved or its size changed, the Highlight Zone changes accordingly.

2. If an un-selected window overlaps the window selected as a Highlight Zone, the Highlight Zone of the selected window turns off.
However, it does not turn off the Zone completely and only makes the window shift to standby mode while the settings are saved. When the window is re­activated, the Highlight Zone turns on again with the settings unchanged.

3. If another un-overlapped window beside one with a Highlight Zone is selected as a Highlight Zone, Highlight Zone function is activated for the two
separate windows simultaneously. (Up to eight windows can be selected as a Highlight Zone and if another window is selected as a Highlight Zone, the
Highlight Zone of the previous windows turns off.)
When the Highlight Zone is created using the Drag function, the Zone functions independently of the above since it uses a random portion of the screen
instead of a particular window.

Note 1 : How to cancel the saved variables of a selected window.

1) When a window selected in Automatic Detect mode is replaced with another window also selected in Automatic Detect mode,
the last selection is saved, and the Highlight Zone function is de-activated for the previous windows.

onl

2) In Manual Detect mode, only the window (or the frame window) created last is saved, and the Highlight Zone function is de-activated for the

previous windows.
The Highlight Zone is de-selected when the program used to create the selected window is closed. The variables of the Highlight Zone created using
the Drag function are not saved.

Note 2 : The changes saved under Picture Setting of the Highlight Zone menu remain effective even after the program is closed using Exit Program.

The next time you start the Highlight Zone program, the settings are shown as previously saved.

Before calling for service, check the information in this section to see if you can remedy any
problems yourself. If you do need assistance, please call the phone number on the

Information section or contact your dealer.

Symptom Check List Solutions

No images on the
screen. I cannot turn
on the monitor.

Is the power cord
connected properly?

Can you see
on the screen?

If the power is on,
reboot the computer to
see the initial screen
(the login screen),
which can be seen.

Can you see
the screen?

There is no image on
the screen.
Is the power indicator
on the monitor blinking
at 1 second intervals?

""

""

on

Check the power cord connection
and supply.

Check the signal cable connection.

If the initial screen (the login screen)
appears, boot the computer in the
applicable mode (the safe mode for
Windows ME/XP/2000) and then
change the frequency of the video
card.
(Refer to the Preset Timing Modes)

Note: If the initial screen (the login
screen) does not appear, contact a

service center or your dealer.

You can see this message when the
signal from the video card exceeds
the maximum resolution and
frequency that the monitor can
properly handle.

Adjust the maximum resolution and
frequency that the monitor can
handle properly.

The monitor is in PowerSaver mode.

Press any key on the keyboard to
activate the monitor and restore the
image on the screen.

The image on the
screen is shaking.

Check the monitor
configuration to see if
it is in Interlace Mode.
(Interlace Mode:
Vertical frequency
43Hz, 87Hz(i), etc)

Are there any Move the monitor away from

The signal from the video card
exceeds the maximum resolution
and frequency of the monitor.

magnetic products
such as a power
adapter, speaker or a
high voltage wire near
by?

Is the voltage stable? The screen image can appear to

The screen image can also appear to shake or vibrate if there is a problem
with the video card or the computer's main board.

anything that can create a strong
magnetic field.

shake or vibrate at a particular time
of day due to low supply voltage.

The screen shows
strange colors or just
black and white.

The screen suddenly
has become
unbalanced.

The screen is out of
focus or OSD cannot
be adjusted.

Is the screen
displaying only one
color as if looking at
the screen through a
cellophane paper?

Have the screen
colors become strange
after running a
program or due to a
crash between
applications?

Has the video card
been set properly?

Have you changed the
video card or the
driver?

Have you adjusted the
resolution or
frequency on the
monitor?

The screen can be unbalanced due to the cycle of the video card signals.
Readjust Position by referring to the OSD.

Have you adjusted the
resolution or
frequency on the
monitor?

Check the signal cable connection.

Make sure the video card is fully
inserted in it's slot.

Reboot the computer.

Set the video card by referring to the
video card manual.

Adjust screen image position and
size using the OSD.

Adjust the resolution and frequency
of the video card.
(Refer to the Preset Timing Modes).

Adjust the resolution and frequency
of the video card.
(Refer to the Preset Timing Modes).

The screen is partially
distorted.

LED is blinking but no
images on the screen.

There are only 16
colors shown on the
screen.
The screen colors
have changed after
changing the video
card.

There is a message
that reads
"Unrecognized
monitor, Plug & Play
(VESA DDC) monitor

Are there any
magnetic products
such as an adapter,
speaker or a high
voltage wire near the
monitor?

Is the frequency
properly adjusted
when checking the
Display Timing on the
menu?

Have the Windows
colors been set
properly?

Has the video card
been set properly?

Have you installed the
monitor driver?

See the video card
manual to see if the
Plug & Play (VESA

Enter the OSD and perform a
"Degauss".

Keep the monitor away from any
magnetic products.

Adjust the frequency properly by
referring to the video card manual
and the Preset Timing Modes.

(The maximum frequency per
resolution may differ from product to
product.)

Windows ME/2000/XP:
Set the colors properly at the

Control Panel → Display →
Settings

Set the video card by referring to the
video card manual.

Install the monitor driver according
to the Driver Installation Instructions.

Install the monitor driver according
to the Driver Installation Instructions.

.

found". DDC) function can be

supported.

Check when
MagicTune does not
function properly.

MagicTune feature is
found only on PC
(VGA) with Window
OS that supports Plug
and Play.

* To check whether your PC is
available for MagicTune feature,
follow the
steps below (When Windows is
XP);

Control Panel -> Performance and
Maintenance -> System ->
Hardware -> Device Manager ->
Monitors -> After deleting Plug and
Play monitor, find 'Plug and Play
monitor' by searching new
Hardware.

MagicTune is an additional software
for the monitor. Some graphic cards
may not support your monitor. When
you have a problem with the graphic
card, visit our website to check the
compatible graphic card list
provided.

http://www.samsung.com/monitor/magictune

MagicTune™ doesn't
work properly.

Have you changed
your PC or video
graphic card?

Download the latest program. The
program can be downloaded

http://www.samsung.com/monitor/magictune.

Visit the MagicTune™ website and download the installation software for MagicTune™
MAC.

Check the following items if there is trouble with the monitor.

1. Check if the power cord and the video cables are properly connected to the computer.

2. Check if the computer beeps more than 3 times when booting.
(If it does, request an after-service for the main board of the computer.)

3. If you installed a new video card or if you assembled the PC, check if the installed adapter (video)
driver and the monitor driver.

4. Check if the scanning ratio of the video screen is set at 50Hz or 160Hz .
(Do not exceed 65Hz when using the maximum resolution.)

5. If you have problems in installing the adapter (video) driver, boot the computer in Safe Mode,
remove the Display Adapter at the "

Control Panel→System→Device Administrator

" and then

reboot the computer to reinstall the adapter (video) driver.

Tips for Highlight Zone

1. To protect CDT against the screen brightness, the Highlight Zone function persists for three
hours and then automatically stops. So please reset it to continue.

2. Once the Highlight Zone has been switched off, you can't select any of the other menus within
the Hightlight Zone.

3. When the Highlight Zone function is operated, the surrounding brightness of screen may become
dark.

4. Depending on the video card you use, a color saturation phenomenon may occur in the Highlight
Zone . In this case, slightly lower the contrast of the Highlight Zone and the color saturation will
be reduced.

If problems repeatedly occur, contact an authorized service center.

Q & A

Question

Answer

How can I change the
frequency?

How can I adjust the resolution? Windows ME/XP/2000 : Set the resolution at the

How can I set the Power Saving
function?

The monitor makes a sound
when it is turned on.

How can I clean the outer
case/Picture tube?

Highlight Zone III 3.5 Q & A

Question

Frequency can be changed by reconfiguring the video card.

Note that video card support can vary, depending on the version
of the driver used. (Refer to the computer or the video card
manual for details.)

Panel→Display→Settings

* Contact the video card manufacturer for details.

Windows ME/XP/2000 : Set the function at BIOS-SETUP of the
computer or the screen saver. (Refer to Windows/Computer
Manual).

This is normal as some sound may be generated when the metal
case and the electromagnet, which are installed to block any
electromagnetic waves, interact with each other.

Disconnect the power cord and then clean the monitor with a soft
cloth, using either a cleaning solution or plain water.

Do not leave any remains of the detergent nor scratch the case.
Do not allow any water to go inside the monitor.

.

Answer

Control

The program does not function
properly.

Started a multimedia program
but the Highlight Zone function
does not automatically activate.

Changed the setting to Highlight
Zone in Manual Detect mode
but the Highlight Zone feature
has not been activated

Highlight Zone III 3.5 features a combination of circuitry and
software built on proprietary technology of SEC. Therefore, the
Highlight Zone III 3.5 feature is found only on SEC monitors that
support the feature.
Check if your monitor supports the Highlight Zone III 3.5 feature.

If not, the Highlight Zone III 3.5 icon will show a message saying,
"No Connection" ( )Connect the monitor properly before using it.

Neither Automatic Detect or nor Manual Detect function while the
icon shows the message, "No Connection". You can only exit the
program.

Check the Highlight Zone III 3.5 menu and see if Disable Auto
Detect is selected.
When selected, the Highlight Zone function is not automatically
activated.

The function may not be activated automatically for some
multimedia programs.
In this case, use Manual Detect instead.
See Manual Detect under (Highlight Zone III 3.5 )

Check the color settings and see if sRGB is selected.
When sRGB is selected, the Highlight Zone function remains de­activated in order to maintain the sRGB color attributes.

Check the color setting of the monitor and see if sRGB is
selected.
When sRGB is selected, the Highlight Zone function remains de­activated in order to maintain the sRGB color attributes.
Some of the windows may not be selected when Highlight Zone
function is on.

Want to turn the Auto Detect
function off.

Don¡¯t know whether the Check the icon on the taskbar.

Set Disable Auto Detect to off from the Highlight Zone III 3.5
menu.
See (Highlight Zone III 3.5 functions)

Highlight program is running.

( ) indicates the function is activated and ( )shows it has been
deactivated.

When a Highlight Zone is on,
the rest of the screen dims.

The Highlight Zone appears too
dark.

Want to adjust the position and
size of the Highlight Zone .

Cannot select Picture Setting. The Picture Setting feature can be selected only when the

Self-Test Feature Check

Self-Test Feature Check | Warning Messages | Environment | Useful Tips

Your monitor provides a self test feature that allows you to check whether your monitor is
functioning properly.

Self-Test Feature Check

1. Turn off both your computer and the monitor.

2. Unplug the video cable from the back of the computer.

3. Turn on the monitor.
If the monitor is functioning properly, you will see a box in the illustration below.

Monitors with the Highlight Zone feature are equipped with an
Automatic Beam Control function. When activated, this may cause
slight dimming of the surrounding screen. However, this does not
indicate a malfunction of any kind, and it is safe to continue to use
the product.

Check the Contrast value in Picture Setting and adjust it for your
ideal viewing.

You can change the position and/or the size of the Highlight Zone
easily using the Manual Detect function.
See (Highlight Zone III 3.5 functions)

Highlight Zone function is on.
Turn the Highlight Zone function on before selecting Picture
Setting.

This box appears during normal operation if the video cable becomes disconnected or
damaged.

4. Turn off your monitor and reconnect the video cable; then turn on both your computer and the
monitor.
If your monitor screen remains blank after using the previous procedure, check your video
controller and computer system; your monitor is functioning properly.

Warning Messages

If there is something wrong with the input signal, the message below appears on the screen
or the screen goes blank although the power indicator LED is still on. The message may
indicate that the monitor is out of scan range or that you need to check the signal cable.

Environment

The location and the position of the monitor may influence the quality and other
features of the monitor.

1. If there are any sub woofer speakers near the monitor, unplug and relocate the woofer
to another room.

2. Remove all electronic devices such as radios, fans, clocks and telephones that are
within 3 feet (one meter) of the monitor.

3. Degauss the monitor if any devices were removed from the area.

Useful Tips

z A monitor recreates visual signals received from the computer. Therefore, if there is trouble with

the computer or the video card, this can cause the monitor to become blank, have poor coloring,
noise, unavailable video mode, etc. In this case, first check the source of the problem, and then
contact a service center or your dealer.

z

Judging the monitor's working condition

If there is no image on the screen or a

message comes up, disconnect the cable from the

""

computer while the monitor is still powered on.

{ If there is a message coming up on the screen or if the screen goes white, this means the

monitor is in working condition.

{ In this case, check the computer for trouble.

General

General

SyncMaster 798MB

Model Name SyncMaster 798MB

Picture Tube

Type 17"(16.0" Viewable)

Deflection angle 90 °

Dot Pitch 0.20mm (Horizontal)

Screen type Aluminized tri-color phosphor dot trio with black matrix.

Anti-doming invar shadow mask.
Multi-layer coated with anti-static.

Resolution

Optimum resolution 1024 x 768 @ 85Hz

Maximum resolution 1280 x 1024 @ 65Hz

Active Display

Horizontal 312 ± 4 mm

Vertical 234 ± 4 mm

Synchronization

Horizontal 30 ~ 70 kHz

Vertical 50 ~ 160 Hz

Input Signal Definition

Video Signal RGB, Analog 0.7 Vpp positive at 75Ω

Sync Signal Separate H/V sync, TTL level, positive or negative

Display Color

Unlimited

Maximum Pixel Clock

120 MHz

Power Supply

AC90~264VAC,50/60Hz

Power Consumption

72W (nominal)

Dimensions (WxDxH) / Weight

401 x 414 x 378 mm / 15.8 X 16.3 X 14.9 inch (with Basic Stand)/ 13.8kg

Environmental considerations

Operating Temperature 32°F ~ 104°F(0°C ~ 40°C)

Humidity 10% ~ 80%, non-condensing

Storage Temperature -4°F ~113°F (-20°C ~ 45°C)

Humidity 5% ~ 95%, non-condensing

Plug and Play Capability

This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and
computer systems will provide the best operating conditions and monitor settings. In most cases,
monitor installation will proceed automatically, unless the user wishes to select alternate settings.

Note: Design and specifications are subject to change without prior notice.

PowerSaver

This monitor has a built-in power management system called PowerSaver. This system saves energy
by switching your monitor into a low-power mode when it has not been used for a certain amount of
time. The monitor automatically returns to normal operation when you press a key on the keyboard. For
energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for
long periods. The PowerSaver system operates with a VESA DPMS compliant video card installed in
your computer. Use a software utility installed on your computer to set up this feature.

State

Normal Operation

Power-off mode

EPA/ENERGY 2000

Power Indicator Green Green, Blinking

Power Consumption 72W (nominal) Less than 1W

This monitor is EPA E

NERGY STAR

®

compliant and ENERGY2000
compliant when used with a computer equipped with VESA DPMS
functionality.

As an E

NERGY STAR

product meets the E

®

Partner, SAMSUNG has determined that this

NERGY STAR

®

guidelines for energy efficiency.

Preset Timing Modes

If the signal transferred from the computer is the same as the following Preset Timing Modes, the
screen will be adjusted automatically. However, if the signal differs, the screen may go blank while
the power LED is on. Refer to the video card manual and adjust the screen as follows.

Horizontal

Display Mode

VESA, 640 x 480 37.500 75.000 31.500 -/-

VESA, 800 x 600 53.700 85.100 56.250 +/+

VESA, 1024 x 768 68.700 85.000 94.500 +/+

Frequency

(kHz)

Horizontal Frequency

The time to scan one line connecting the right edge to the left edge of
the screen horizontally is called Horizontal Cycle and the inverse
number of the Horizontal Cycle is called Horizontal Frequency. Unit:
kHz

Vertical Frequency

Like a fluorescent lamp, the screen has to repeat the same image
many times per second to display an image to the user. The
frequency of this repetition is called Vertical Frequency or Refresh
Rate. Unit: Hz

Vertical

Frequency

(Hz)

Pixel Clock

(MHz)

Sync Polarity

(H/V)

General

General

SyncMaster 798MBplus

Model Name SyncMaster 798MBplus

Picture Tube

Type 17"(16.0" Viewable)

Deflection angle 90 °

Dot Pitch 0.20mm (Horizontal)

Screen type Aluminized tri-color phosphor dot trio with black matrix.

Anti-doming invar shadow mask.
Multi-layer coated with anti-static.

Resolution

Optimum resolution 1024 x 768 @ 85Hz

Maximum resolution 1280 x 1024 @ 65Hz

Active Display

Horizontal 312 ± 4 mm

Vertical 234 ± 4 mm

Synchronization

Horizontal 30 ~ 70 kHz

Vertical 50 ~ 160 Hz

Input Signal Definition

Video Signal RGB, Analog 0.7 Vpp positive at 75Ω

Sync Signal Separate H/V sync, TTL level, positive or negative

Display Color

Unlimited

Maximum Pixel Clock

120 MHz

Power Supply

AC90~264VAC,50/60Hz

Power Consumption

72W (nominal)

Dimensions (WxDxH) / Weight

401 x 414 x 378 mm / 15.8 X 16.3 X 14.9 inch (with Basic Stand)/ 13.8kg

Environmental considerations

Operating Temperature 32°F ~ 104°F(0°C ~ 40°C)

Humidity 10% ~ 80%, non-condensing

Storage Temperature -4°F ~113°F (-20°C ~ 45°C)

Humidity 5% ~ 95%, non-condensing

Plug and Play Capability

This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and
computer systems will provide the best operating conditions and monitor settings. In most cases,
monitor installation will proceed automatically, unless the user wishes to select alternate settings.

Note: Design and specifications are subject to change without prior notice.

PowerSaver

This monitor has a built-in power management system called PowerSaver. This system saves energy
by switching your monitor into a low-power mode when it has not been used for a certain amount of
time. The monitor automatically returns to normal operation when you press a key on the keyboard. For
energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for
long periods. The PowerSaver system operates with a VESA DPMS compliant video card installed in
your computer. Use a software utility installed on your computer to set up this feature.

State

Normal Operation

Power-off mode

EPA/ENERGY 2000

Power Indicator Green Green, Blinking

Power Consumption 72W (nominal) Less than 1W

This monitor is EPA E

NERGY STAR

®

compliant and ENERGY2000
compliant when used with a computer equipped with VESA DPMS
functionality.

As an E

NERGY STAR

product meets the E

®

Partner, SAMSUNG has determined that this

NERGY STAR

®

guidelines for energy efficiency.

Preset Timing Modes

If the signal transferred from the computer is the same as the following Preset Timing Modes, the
screen will be adjusted automatically. However, if the signal differs, the screen may go blank while
the power LED is on. Refer to the video card manual and adjust the screen as follows.

Horizontal

Display Mode

VESA, 640 x 480 37.500 75.000 31.500 -/-

VESA, 800 x 600 53.700 85.100 56.250 +/+

VESA, 1024 x 768 68.700 85.000 94.500 +/+

Frequency

(kHz)

Horizontal Frequency

The time to scan one line connecting the right edge to the left edge of
the screen horizontally is called Horizontal Cycle and the inverse
number of the Horizontal Cycle is called Horizontal Frequency. Unit:
kHz

Vertical Frequency

Like a fluorescent lamp, the screen has to repeat the same image
many times per second to display an image to the user. The
frequency of this repetition is called Vertical Frequency or Refresh
Rate. Unit: Hz

Vertical

Frequency

(Hz)

Pixel Clock

(MHz)

Sync Polarity

(H/V)

SyncMaster 798MB

Service

The address and phone number of the company can be changed without previous notice.

AUSTRALIA :

Samsung Electronics Australia Pty Ltd.
Customer Response Centre
7 Parkview Drive, Homebush Bay NSW 2127
Tel : [phone]

http://www.samsung.com.au/

BRAZIL :

Samsung Eletronica da Amazonia Ltda.
R. Prof. Manoelito de Ornellas, 303, Terro B
Chacara Sto. Antonio, CEP : 04719-040
Sao Paulo, SP
SAC : 0800 124 421

http://www.samsung.com.br/

CANADA :

Samsung Electronics Canada Inc.,
Samsung Customer Care
55 Standish Court
Mississauga, Ontario L5R 4B2
1-800-SAMSUNG (1-800-726-7864)

http://www.samsung.ca/

CHILE :

SONDA S.A.
Teatinos 550, Santiago Centro, Santiago, Chile
Fono: 56-2-5605000 Fax: [phone]
56-2-800200211

http://www.sonda.com/
http://www.samsung.cl/

COLOMBIA :

Samsung Electronics Colombia
Cra 9 No 99A-02 Of. 106
Bogota, Colombia
Tel.: [phone]
Fax: (571) 618 - 2068

http://www.samsung-latin.com/

e-mail : [e-mail]

ESPAÑA :

Samsung Electronics Comercial Iberica, S.A.
Ciencies, 55-65 (Poligono Pedrosa) 08908
Hospitalet de Llobregat (Barcelona)
Tel. : [phone]
Fax. : [phone]

http://samsung.es/

FRANCE :

SAMSUNG ELECTRONICS FRANCE Service
Paris Nord 2
66 rue des Vanesses
BP 50116 Villepinte
95950 Roissy CDG Cedex
Tel : [phone]
Fax : [phone]

http://www.samsungservices.com/

GERMANY :

TELEPLAN Rhein-Main GmbH
Feldstr. 16
64331 Weiterstadt
T. 06151/957-1306
F. 06151/957-1732
* EURO 0.12/Min

http://www.samsung.de/

HUNGARY :

Samsung Electronics Magyar Rt.
1039, Budapest, Lehel u. 15-17.
Tel: [phone]
Fax: [phone]

http://www.samsung.hu/

ITALY :

Samsung Electronics Italia S.p.a.
Via C. Donat Cattin, 5
20063 Cernusco s/Naviglio (MI)
Servizio Clienti: 199.153.153

http://www.samsung-italia.com/

MÉXICO :

SAMSUNG ELECTRONICS MÉXICO. S.A. DE C.V.
Vía Lopez Portillo No. 6, Col. San Fco. Chilpan
Tultitlán, Estado de México, C.P. 54940
Tel: [phone]
Fax: [phone]
RFC: SEM950215S98

http://www.samsung.com.mx/

IMPORTADO POR: SAMSUNG ELECTRONICS MÉXICO. S.A. DE C.V.

EXPORTADO POR: Samsung Electronics CO.,LTD.

NETHERLANDS/BELGIUM/LUXEMBOURG :

Samsung Electronics Benelux B. V.
Fleminglaan 12 2289 CP Rijiswijk, NEDERLANDS
Service and informatielijn ;
Belgium :0800-95214, http://www.samsung.be/
Netherlands : 0800-2295214, http://www.samsung.nl/

Vía Lopez Portillo No. 6, Col. San Fco. Chilpan
Tultitlán, Estado de México, C.P. 54940
Tel: [phone]

416, Mae tan-3dong, Yeongtong - gu,
Suwon City, Gyeonggi-do Korea

PANAMA :

Samsung Electronics Latinoamerica( Z.L.) S.A.
Calle 50 Edificio Plaza Credicorp, Planta Baja
Panama
Tel. : [phone]
Tel : [phone](FAST)

http://www.samsung-latin.com/

PERU :

Servicio Integral Samsung
Av.Argentina 1790 Lima1. Peru
Tel: [phone]
Fax: [phone]

http://www.samsungperu.com/

PORTUGAL :

SAMSUNG ELECTRONICA PORTUGUESA S.A.
Rua Mário Dioniso, N

o

2 - 1º Drt. 2795-140 LINDA-A-VELHA
Tel. [phone] Fax. [phone]
Free Line 800 220 120

http://www.samsung.pt/

SOUTH AFRICA :

Samsung Electronics,5 Libertas Road, Somerset Office Park,
Bryanston Ext 16. Po Box 70006, Bryanston,2021, South Africa
Tel : [phone]
Fax : [phone]

http://www.samsung.co.za/

SWEDEN/DENMARK/NORWAY/FINLAND :

Samsung Electronics AB
Box 713
S-194 27 UPPLANDS VÄSBY
SVERIGE
Besöksadress : Johanneslundsvägen 4
Samsung support Sverige: 020-46 46 46
Samsung support Danmark : 8088-4646
Samsung support Norge: 8001-1800
Samsung support Finland: 0800-118001
Tel [phone]
Fax [phone]

http://www.samsung.se/

THAILAND :

HAI SAMSUNG SERVICE CENTER
MPA COMPLEX BUILDING,1st-2nd Floor
175 SOI SUEKSA VIDHAYA SATHON SOI 12
SILOM ROAD ,SILOM,BANGRAK
BANGKOK 10500
TEL : [phone]
FAX : [phone]

UKRAINE :

SAMSUNG ELECTRONICS REPRESENTATIVE OFFICE IN UKRAINE
4 Glybochitska str.
Kiev, Ukraine
Tel. [phone]
Fax [phone]
Toll-free 8-800-502-0000

http://www.samsung.com.ua/

United Kingdom :

Samsung Electronics (UK) Ltd.
Samsung House, 225 Hook Rise South

Surbiton, Surrey KT6 7LD
Tel. : [phone]
Fax. : [phone]
< European Service Center & National Service >
Stafford Park 12 Telford, Shropshire, TF3 3BJ
Tel. : [phone]
Fax. : [phone]

http://samsungservice.co.uk/

U.S.A :

Samsung Electronics America
Service Division
400 Valley Road, Suite 201
Mount Arlington, NJ 07856
1-800-SAMSUNG (1-800-726-7864)

http://samsung.com/monitor/

Terms

Dot Pitch

The image on a monitor is composed of red, green and blue dots. The closer the dots, the
higher the resolution. The distance between two dots of the same color is called the 'Dot
Pitch'. Unit: mm

Vertical Frequency

The screen must be redrawn several times per second in order to create and display an image
for the user. The frequency of this repetition per second is called Vertical Frequency or
Refresh Rate. Unit: Hz

Example: If the same light repeats itself 60 times per second, this is regarded as 60 Hz.

Horizontal Frequency

The time to scan one line connecting the right edge to the left edge of the screen horizontally
is called Horizontal Cycle. The inverse number of the Horizontal Cycle is called Horizontal
Frequency. Unit: kHz

Interlace and Non-Interlace Methods

Showing the horizontal lines of the screen from the top to the bottom in order is called the
Non-Interlace method while showing odd lines and then even lines in turn is called the
Interlace method. The Non-Interlace method is used for the majority of monitors to ensure a
clear image. The Interlace method is the same as that used in TVs.

Plug & Play

This is a function that provides the best quality screen for the user by allowing the computer
and the monitor to exchange information automatically. This monitor follows the international
standard VESA DDC for the Plug & Play function.

Resolution

The number of horizontal and vertical dots used to compose the screen image is called
'resolution'. This number shows the accuracy of the display. High resolution is good for
performing multiple tasks as more image information can be shown on the screen.

Example: If the resolution is 1024 X 768, this means the screen is composed of 1024

Highlight Zone III 3.5

Highlight Zone is an enhancement feature to increase luminance in a certain area of the
monitor for brighter and sharper images/photos. Highlight Zone III 3.5 is carried by Samsung’s

horizontal dots (horizontal resolution) and 768 vertical lines (vertical resolution).

unique circuit technology and a powerful combination of programs in order to implement the
Highlight Zone feature. This is a user friendly program that automatically highlights a certain
video area or enables users to specify an area of their choice to be highlighted.

MagicBright™

MagicBright is an advanced monitor that boasts more than twice the brightness and sharpness
compared to conventional models, and which provides a contextual display environment
depending on word processing, internet, game or video purposes. The user can use the front
button panel to control the screen at four different levels of brightness and sharpness for their
preference.

Authority

Information in this document is subject to change without notice.
© 2005 Samsung Electronics Co., Ltd. All rights reserved.

Reproduction in any manner whatsoever without the written permission of Samsung Electronics
Co., Ltd. is strictly forbidden.

Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or
consequential damages in connection with the furnishing, performance, or use of this material.

Samsung is the registered trademark of Samsung Electronics Co., Ltd.; Microsoft, Windows and
Windows NT are registered trademarks of Microsoft Corporation; VESA, DPMS and DDC are
registered trademarks of Video Electronics Standard Association; the E

NERGY STAR® name and

logo are registered trademarks of the U.S. Environmental Protection Agency (EPA). As an ENERGY
STAR® Partner, Samsung Electronics Co., Ltd. has determined that this product meets the
ENERGY STAR® guidelines for energy efficiency. All other product names mentioned herein may be
the trademarks or registered trademarks of their respective owners.

Class B

This device is a Class B digital apparatus. For Safety and EMC compliance guide, you may refer
to "Regulatory" Guide.

SyncMaster 798MBplus

Service

The address and phone number of the company can be changed without previous notice.

AUSTRALIA :

Samsung Electronics Australia Pty Ltd.
Customer Response Centre
7 Parkview Drive, Homebush Bay NSW 2127
Tel : [phone]

http://www.samsung.com.au/

BRAZIL :

Samsung Eletronica da Amazonia Ltda.
R. Prof. Manoelito de Ornellas, 303, Terro B
Chacara Sto. Antonio, CEP : 04719-040
Sao Paulo, SP
SAC : 0800 124 421

http://www.samsung.com.br/

CANADA :

Samsung Electronics Canada Inc.,
Samsung Customer Care
55 Standish Court
Mississauga, Ontario L5R 4B2
1-800-SAMSUNG (1-800-726-7864)

http://www.samsung.ca/

CHILE :

SONDA S.A.
Teatinos 550, Santiago Centro, Santiago, Chile
Fono: 56-2-5605000 Fax: [phone]
56-2-800200211

http://www.sonda.com/
http://www.samsung.cl/

COLOMBIA :

Samsung Electronics Colombia
Cra 9 No 99A-02 Of. 106
Bogota, Colombia
Tel.: [phone]
Fax: (571) 618 - 2068

http://www.samsung-latin.com/

e-mail : [e-mail]

ESPAÑA :

Samsung Electronics Comercial Iberica, S.A.
Ciencies, 55-65 (Poligono Pedrosa) 08908
Hospitalet de Llobregat (Barcelona)
Tel. : [phone]
Fax. : [phone]

http://samsung.es/

FRANCE :

SAMSUNG ELECTRONICS FRANCE Service
Paris Nord 2
66 rue des Vanesses
BP 50116 Villepinte
95950 Roissy CDG Cedex
Tel : [phone]
Fax : [phone]

http://www.samsungservices.com/

GERMANY :

TELEPLAN Rhein-Main GmbH
Feldstr. 16
64331 Weiterstadt
T. 06151/957-1306
F. 06151/957-1732
* EURO 0.12/Min

http://www.samsung.de/

HUNGARY :

Samsung Electronics Magyar Rt.
1039, Budapest, Lehel u. 15-17.
Tel: [phone]
Fax: [phone]

http://www.samsung.hu/

ITALY :

Samsung Electronics Italia S.p.a.
Via C. Donat Cattin, 5
20063 Cernusco s/Naviglio (MI)
Servizio Clienti: 199.153.153

http://www.samsung-italia.com/

MÉXICO :

SAMSUNG ELECTRONICS MÉXICO. S.A. DE C.V.
Vía Lopez Portillo No. 6, Col. San Fco. Chilpan
Tultitlán, Estado de México, C.P. 54940
Tel: [phone]
Fax: [phone]
RFC: SEM950215S98

http://www.samsung.com.mx/

IMPORTADO POR: SAMSUNG ELECTRONICS MÉXICO. S.A. DE C.V.

EXPORTADO POR: Samsung Electronics CO.,LTD.

NETHERLANDS/BELGIUM/LUXEMBOURG :

Samsung Electronics Benelux B. V.
Fleminglaan 12 2289 CP Rijiswijk, NEDERLANDS
Service and informatielijn ;
Belgium :0800-95214, http://www.samsung.be/
Netherlands : 0800-2295214, http://www.samsung.nl/

Vía Lopez Portillo No. 6, Col. San Fco. Chilpan
Tultitlán, Estado de México, C.P. 54940
Tel: [phone]

416, Mae tan-3dong, Yeongtong - gu,
Suwon City, Gyeonggi-do Korea

PANAMA :

Samsung Electronics Latinoamerica( Z.L.) S.A.
Calle 50 Edificio Plaza Credicorp, Planta Baja
Panama
Tel. : [phone]
Tel : [phone](FAST)

http://www.samsung-latin.com/

PERU :

Servicio Integral Samsung
Av.Argentina 1790 Lima1. Peru
Tel: [phone]
Fax: [phone]

http://www.samsungperu.com/

PORTUGAL :

SAMSUNG ELECTRONICA PORTUGUESA S.A.
Rua Mário Dioniso, N

o

2 - 1º Drt. 2795-140 LINDA-A-VELHA
Tel. [phone] Fax. [phone]
Free Line 800 220 120

http://www.samsung.pt/

SOUTH AFRICA :

Samsung Electronics,5 Libertas Road, Somerset Office Park,
Bryanston Ext 16. Po Box 70006, Bryanston,2021, South Africa
Tel : [phone]
Fax : [phone]

http://www.samsung.co.za/

SWEDEN/DENMARK/NORWAY/FINLAND :

Samsung Electronics AB
Box 713
S-194 27 UPPLANDS VÄSBY
SVERIGE
Besöksadress : Johanneslundsvägen 4
Samsung support Sverige: 020-46 46 46
Samsung support Danmark : 8088-4646
Samsung support Norge: 8001-1800
Samsung support Finland: 0800-118001
Tel [phone]
Fax [phone]

http://www.samsung.se/

THAILAND :

HAI SAMSUNG SERVICE CENTER
MPA COMPLEX BUILDING,1st-2nd Floor
175 SOI SUEKSA VIDHAYA SATHON SOI 12
SILOM ROAD ,SILOM,BANGRAK
BANGKOK 10500
TEL : [phone]
FAX : [phone]

UKRAINE :

SAMSUNG ELECTRONICS REPRESENTATIVE OFFICE IN UKRAINE
4 Glybochitska str.
Kiev, Ukraine
Tel. [phone]
Fax [phone]
Toll-free 8-800-502-0000

http://www.samsung.com.ua/

United Kingdom :

Samsung Electronics (UK) Ltd.
Samsung House, 225 Hook Rise South

Surbiton, Surrey KT6 7LD
Tel. : [phone]
Fax. : [phone]
< European Service Center & National Service >
Stafford Park 12 Telford, Shropshire, TF3 3BJ
Tel. : [phone]
Fax. : [phone]

http://samsungservice.co.uk/

U.S.A :

Samsung Electronics America
Service Division
400 Valley Road, Suite 201
Mount Arlington, NJ 07856
1-800-SAMSUNG (1-800-726-7864)

http://samsung.com/monitor/

Terms

Dot Pitch

The image on a monitor is composed of red, green and blue dots. The closer the dots, the
higher the resolution. The distance between two dots of the same color is called the 'Dot
Pitch'. Unit: mm

Vertical Frequency

The screen must be redrawn several times per second in order to create and display an image
for the user. The frequency of this repetition per second is called Vertical Frequency or
Refresh Rate. Unit: Hz

Example: If the same light repeats itself 60 times per second, this is regarded as 60 Hz.

Horizontal Frequency

The time to scan one line connecting the right edge to the left edge of the screen horizontally
is called Horizontal Cycle. The inverse number of the Horizontal Cycle is called Horizontal
Frequency. Unit: kHz

Interlace and Non-Interlace Methods

Showing the horizontal lines of the screen from the top to the bottom in order is called the
Non-Interlace method while showing odd lines and then even lines in turn is called the
Interlace method. The Non-Interlace method is used for the majority of monitors to ensure a
clear image. The Interlace method is the same as that used in TVs.

Plug & Play

This is a function that provides the best quality screen for the user by allowing the computer
and the monitor to exchange information automatically. This monitor follows the international
standard VESA DDC for the Plug & Play function.

Resolution

The number of horizontal and vertical dots used to compose the screen image is called
'resolution'. This number shows the accuracy of the display. High resolution is good for
performing multiple tasks as more image information can be shown on the screen.

Example: If the resolution is 1024 X 768, this means the screen is composed of 1024

Highlight Zone III 3.5

Highlight Zone is an enhancement feature to increase luminance in a certain area of the
monitor for brighter and sharper images/photos. Highlight Zone III 3.5 is carried by Samsung’s

horizontal dots (horizontal resolution) and 768 vertical lines (vertical resolution).

unique circuit technology and a powerful combination of programs in order to implement the
Highlight Zone feature. This is a user friendly program that automatically highlights a certain
video area or enables users to specify an area of their choice to be highlighted.

MagicBright™

MagicBright is an advanced monitor that boasts more than twice the brightness and sharpness
compared to conventional models, and which provides a contextual display environment
depending on word processing, internet, game or video purposes. The user can use the front
button panel to control the screen at four different levels of brightness and sharpness for their
preference.

MagicGreen

The MagicGreen CDT monitor has adopted a Well-Being CDT that is coated with a Vital &
Pure coating, which radiates far infrared and anion and provides antibacterial and deodorizing
effects.

z

Vital Coating

Radiates far infrared and anion by applying a specialized ceramic on the

surface of the CDT funnel.

z

Pure Coating

Provides antibacterial deodorizing effects by treating the surface with

photocatalyst TiO2 and Nano Silver.

Authority

Information in this document is subject to change without notice.
© 2005 Samsung Electronics Co., Ltd. All rights reserved.

Reproduction in any manner whatsoever without the written permission of Samsung Electronics
Co., Ltd. is strictly forbidden.

Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or
consequential damages in connection with the furnishing, performance, or use of this material.

Samsung is the registered trademark of Samsung Electronics Co., Ltd.; Microsoft, Windows and
Windows NT are registered trademarks of Microsoft Corporation; VESA, DPMS and DDC are
registered trademarks of Video Electronics Standard Association; the E

NERGY STAR® name and

logo are registered trademarks of the U.S. Environmental Protection Agency (EPA). As an E
S

TAR® Partner, Samsung Electronics Co., Ltd. has determined that this product meets the

ENERGY STAR® guidelines for energy efficiency. All other product names mentioned herein may be
the trademarks or registered trademarks of their respective owners.

Class B

This device is a Class B digital apparatus. For Safety and EMC compliance guide, you may refer
to "Regulatory" Guide.

NERGY

Correct Disposal of This Product
(Waste Electrical & Electronic Equipment) - Europe only

(Applicable in the European Union and other European countries with
separate collection systems)

This marking shown on the product or its literature, indicates that it should not
be disposed with other household wastes at the end of its working life. To
prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources.

Household users should contact either the retailer where they purchased this
product, or their local government office, for details of where and how they
can take this item for environmentally safe recycling.

Business users should contact their supplier and check the terms and
conditions of the purchase contract. This product should not be mixed with
other commercial wastes for disposal.