Samsung 797DF, 793MB, 795DF, 795MB, 793DF User Manual 2

...

SyncMaster 591S/793S/793DF/795DF/797DF/997DF/793MB/795MB

INDEX

Main Page

Safety Instructions

Notational

Power

nstallation

Cleaning

Other

Introduction

󰼿󰼿󰼿󰼿󰼿Unpacking

󰼿󰼿󰼿󰼿󰼿󰼿Front

󰼿󰼿󰼿󰼿󰼿󰼿Rear

󰼿󰼿󰼿󰼿󰼿󰼿Bottom

Setup

Troubleshooting

󰼿󰼿󰼿󰼿󰼿󰼿󰼿󰼿Check List

󰼿󰼿󰼿󰼿󰼿󰼿󰼿󰼿Q & A

󰼿󰼿󰼿󰼿󰼿󰼿

󰼿󰼿󰼿󰼿󰼿󰼿󰼿󰼿Self-Test Feature Check

Specifications

󰼿󰼿󰼿󰼿󰼿󰼿󰼿󰼿General Specifications

󰼿󰼿󰼿󰼿󰼿󰼿󰼿󰼿Preset Timing Modes

󰼿󰼿󰼿󰼿󰼿󰼿󰼿󰼿PowerSaver

Information

󰼿󰼿󰼿󰼿󰼿󰼿󰼿󰼿Service

󰼿󰼿󰼿󰼿󰼿󰼿󰼿󰼿Terms 󰼿󰼿󰼿󰼿󰼿󰼿󰼿󰼿Natural Color

󰼿󰼿󰼿󰼿󰼿󰼿󰼿󰼿Authority

󰼿󰼿󰼿󰼿󰼿󰼿Connecting Your Monitor

󰼿󰼿󰼿󰼿󰼿󰼿󰼿Installing the Monitor Driver

󰼿Automatic

󰼿Manual

Base Installation

Notational

Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment.

Prohibited Important to read and understand at all times

Do not disassemble Disconnect the plug from the outlet

Do not touch Grounding to prevent an electric shock

Power

When not used for extended periods of time, set your PC to DPMS. If using a screen saver, set it to the active screen mode.

If the size of your monitor is small, or if the same image is present for long

periods of time, you may see afterimages due to damage to the fluorescent substance on the inside of the CDT.

Do not use a damaged or loose plug.

This may cause an electric shock or fire.

Do not pull the plug out by the wire nor touch the plug with wet hands.

This may cause an electric shock or fire.

Use only a properly grounded plug and receptacle.

An improper ground may cause electric shock or equipment

damage.

Do not excessively bend the plug and wire nor place heavy objects upon them, which could cause damage.

Failure to do so may cause an electric shock or fire.

Disconnect the plug from the outlet during storms or lightening or if it is not used for a long period of time.

Failure to do so may cause an electric shock or fire.

Do not connect too many extension cords or plugs to an outlet.

This may cause a fire.

Installation

Do not cover the vents on the monitor cabinet.

Bad ventilation may cause a breakdown or fire.

Put your monitor in a location with low humidity and a minimum of dust.

An electric shock or fire could result inside the monitor.

Do not drop the monitor when moving it.

This may cause damage to the product or human body.

Place the monitor on a flat and stable surface.

The monitor can cause injury by falling.

Set down the monitor carefully.

It could be damaged or broken.

Do not place the monitor face down.

The CDT surface may be damaged.

Do not use the monitor without the monitor stand.

It could break down or cause a fire due to bad ventilation.

If the monitor must be used without the supplied stand, take steps

to insure proper ventilation.

Cleaning

When cleaning the monitor case or the surface of the CDT, wipe with a slightly moistened, soft fabric.

Do not clean Flat monitor with water. Use a water-diluted mild detergent.

(Some detergents contain significant amounts of alcohol-based solvents, which can damage (color change) or crack the monitor case. The antiglare/anti-static surface coating on the CDT may also be affected.)

Dilute the detergent (1:10 ratio) with water before using.

Do not spray detergent directly on the monitor.

Use the recommended detergent with a smooth cloth.

You can prevent the coated CDT from being damaged or the

monitor cabinet from being dissolved, cracked or discolored. You can buy a recommended detergent at any Samsung Service

Center.

If the connector between the plug and the pin is dusty or dirty, clean it properly with a dry cloth.

A dirty connector can cause an electric shock or fire.

Do not set a glass of water, chemicals or any small metal objects on the monitor.

This may cause damage, electric shock or a fire.

If a foreign substance gets into the monitor, disconnect the plug

and then contact a service center.

Other

Do not remove cover(or back). No user serviceable parts inside.

This may cause an electric shock or a fire.

Refer servicing to qualified service personnel.

If your monitor does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it immediately and contact an authorized dealer or service.

This may cause an electric shock or a fire.

Do not place any heavy objects on the monitor.

This may cause an electric shock or a fire.

For each hour of looking at the monitor, you should let your eyes rest for 5 minutes.

This will reduce eye fatigue.

Do not use or store inflammable substances near the monitor.

This may cause an explosion or fire.

Do not try to move the monitor by pulling on the wire or the signal cable.

This may cause a breakdown, electric shock or a fire due to

damage to the cable.

Do not move the monitor right or left by pulling only the wire or the signal cable.

This may cause a breakdown, electric shock or a fire due to

damage to the cable.

Never insert anything metallic into the monitor openings.

This may cause an electric shock, fire or injury.

Other

Keep the monitor away from any magnetic substances.

This may cause discoloring or distortion of the image.

Unpacking

Monitor and Stand

(Some models include a stand attached. )

Please make sure the following items are included

with your monitor. If any items are missing,

contact your dealer.

Power Cord

Stand

Quick Setup Guide

Warranty Card

(Not available in all locations)

For Multimedia model

Multimedia Speaker Stand

User's Guide and

Driver Installation CD

Sound Cables(2each)

DC Power Cord (Option)

User Guide

Front

1. Menu button

2. Adjust buttons

3. Enter button

4. Power button

5. Power indicator

See PowerSaver described in the manual for further information regarding power saving

Note:

functions. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods.

Opens the OSD menu. Also used to exit the OSD menu or return to the previous menu.

These buttons allow you to highlight and adjust items in the menu.

Used to select the OSD menu.

Use this button to turn the monitor on and off.

This light glows green during normal operation, and blinks green once as the monitor saves your adjustments.

Rear

General

SyncMaster 591S/793S/793DF/795DF

/797DF/997DF/793MB/795MB

(The configuration at the back of the monitor may vary from product to product.)

1. Power port

2. Signal Cable

BNC Connectors (Option)

Connect the power cord for your monitor to the power port on the back of the monitor.

Connect the signal cable to the video port on your computer, video board, video card, or graphics card.

SyncMaster 997DF

(The configuration at the back of the monitor may vary from product to product.)

1. Power port

2. Signal port

3. BNC Connectors (Option)

Note:

See Connecting Your Monitor for further information regarding cable connections.

Connect the power cord for your monitor to the power port on the back of the monitor.

Connect the signal cable to the 15-pin D-sub connector on the back of your monitor.

Connect the signal cable to the BNC signal port on the back of your monitor.

Bottom

1. Signal Cable

2. Power port

3. Tilt/Swivel Base

Connect the signal cable to the video port on your computer, video board, video card, or graphics card.

Connect the power cord for your monitor to the power port on the back of the monitor.

You can separate the base from the monitor.

Connecting Your Monitor

SyncMaster 591S/793S/793DF/795DF

General

1. Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet.

2. Connect the signal cable to the video port on your computer, video board, video card, or graphics card.

3. If you are using a Macintosh computer, connect the cable to a Macintosh adapter, and set the pins on your adapter(Adapter not included). A PC-compatible computer does not need an adapter.

4. Turn on your computer and monitor. If your monitor displays an image, installation is complete.

/797DF/997DF/793MB/795MB

BNC Connectors (Option)

SyncMaster 997DF

1. Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet.

2. Connect the end of the signal cable to your computer's video port(video board, video card or graphics card).

3. If you are using a Macintosh computer, connect the cable to a Macintosh adapter, and set the

Connecting Your Monitor

pins on your adapter(Adapter not included). A PC-compatible computer does not need an adapter.

4. When you use a BNC connector. Connect the signal cable to the BNC signal port on the back of your monitor/computer.

5. Turn on your computer and monitor. If your monitor displays an image, installation is complete.

Opstilling-For multimedia-model

1. Sluk for computeren og fjern strømkablet.

2. Tilslut signalkablet til din computers videoport (videoboard, videokort eller grafikkort).

3. Tilslut den ene ende af et lydkabel til stereo output jacket på lydkort eller computer. Tilslut den anden ende af kablet til stereo input jacket bag på monitorens fod. Tilslut den ene ende af det andet lydkabel til linie output jacket på lydkort eller computer. Tilslut den anden af kablet til Mic By-Pass jacket bag på monitorens fod.

4. Tilslut DC strømkablet (jævnstrøm) fra fodstykket til den nærmeste stikkontakt.

5. Tilslut monitorens strømkabel til strømporten bag på monitoren.

6. Tilslut monitorens strømkabel og computerens strømkabel til et stik i nærheden.

7. Tænd for computer og monitor.

8. Drej op eller ned på ON-OFF knappen på monitorens fod, indtil den klikker.

9. Start et lydprogram, musik eller lydeffekt på din computer og juster lydstyrken ved at skrue op eller ned til den ønskede lydstyrke.

10. Juster diskant og bas.

BEMÆRK:

Lydforvrængning kan forekomme, hvis monitoren er placeret oven på et stort set hult kabinet, som f.eks. din computer. Hvis det sker, kan du anbringe en skriveblok eller et blad under monitorens fod. Høj lydstyrke kan også resultere i forvrængning af lyden; skru ned for lyden.

Connecting Your Monitor

Fodstykke for Multimedia højttaler

Mic by-pass jack

For transmission af din stemme, tilslut et lydkabel fra mic by-pass jack til mic in jack på lydkortets slot i din computer.

Stereo input jack

Tilslut et lydkabel fra input kilden (lydkort, computer, CD-ROM drev).

DC strømkabel

Tilsluttes til monitorens DC 12V output jack.

Strømindikator

Lyser grøn, når der er tændt for højttalerne.

On/Off lydstyrke

Tænder/slukker og justerer lydstyrken

Diskant kontrolknap

Bruges til kontrol af høje frekvenser.

Bas kontrol knap

Bruges til kontrol af lave frekvenser.

Mic input jack

For transmission af din stemme, tilslut en mikrofon til dette jack.

Jack til øretelefoner

Øretelefoner kan tilsluttes her.

10.

Aftagelig overdel til fodstykke.

+ 35 hidden pages