Sagem PHOTO EASY 155 User Guide

SAGEM

PHOTO EASY 155

Livret d’utilisation

Bedienungsanleitung

Manual del usuario

Manuale dell'utente

Gebruiksaanwijzing

User guide

1WELCOME 1

2DISCOVER YOUR PHOTO EASY 155 PRINTER 2

3PREPARE YOUR PHOTO EASY 155 PRINTER 3

Connect the mains supply 3 First ribbon installation 4 To change the ribbon 5 Loading paper 6

4PRINTING FROM A MEMORY CARD 7

Insert a memory card 7

5USER INTERFACE 9

Print your photographs 10 Rapid printing 10 Example of rapid printing from a memory card 11 Create a contact sheet (index) 13 Prepare a series of photographs for printing (shopping trolley mode) Print from a camera (PictBrigde mode) 16 Print in DPOF (Digital Print Order Format) mode 17 Printing from a GSM mobile phone camera 18 Print starting from a bluetooth peripheral (optional) 19 Print from a PC (Personal Computer) 21

6REPLACEMENT OF CONSUMABLES 23

7MAINTENANCE 24

Cleaning the print head 24 Paper jam 25 Problems 26 Error messages 27 Technical data 29

ENGLISH

FRANÇAIS

DEUTSCH

ESPAÑOL

8GARANTEE 30

- I -

ITALIANO

NEDERLANDS

- II -

1WELCOME

You have just acquired a SAGEM PHOTO EASY 155 printer, and we thank you for choosing our product. With this high quality printer you can get the most out of your digital photos. In a few simple steps you can produce photo prints identical to those from a professional developer, for your personal use or to share with friends and family.

The easy-to-follow steps in this user guide will walk you through:

1. Switching on your PHOTO EASY 155 printer

2. Printing photographs stored on a memory card

3. Printing photographs transferred from a camera in a GSM mobile phone

4. Installing the image processing software and printer driver on a PC

5. Maintenance and troubleshooting of your PHOTO EASY 155 printer

The CD-ROM included with your kit contains an additional guide with instructions for using the image processing software and printer driver on your PC.

Safety instructions and recommendations

• Do not install your PHOTO EASY 155 printer in a humid room (bathroom, laundry, kitchen, etc.), or within 1.50 m of a tap or water source, or outside. The printer should be operated within an ambient temperature range of 10 °C to 35 °C.

• Do not install your printer in a location where there is a noticeable amount of dust floating in the air. Such dust can degrade the print quality of your photos.

• Only the power supply provided with the printer should be used. Connect this to the mains in accordance with the installation instructions in this user guide and the information on the identification label affixed to the power supply (voltage, current, mains frequency). As a precaution, in case of danger, the mains adapters act as a disconnecting mechanism for the 230V power supply. They should be placed near the device and should be easily accessible.

• Never open the cover of the film cartridge compartment during printing. This could break the film and cause printer malfunction.

• Only use SAGEM consumables, if not you are likely to damage the equipment and invalidate the guarantee. To obtain the references of the consumables (Refer to paragraph Repla- cement of consumables, page -23).

• The CE marking certifies that the product meets the main requirements of the European Parliament and Council directive 1999/5/CE on telecommunications terminal equipment, regarding safety and health of users, and regarding electromagnetic interference.

ENGLISH

FRANÇAIS

DEUTSCH

ESPAÑOL

ITALIANO

The declaration of compliance can be consulted on the site www.sagem.com category "support", or can be requested at the following address:

E - Customer relations department

4 rue du petit albi - 95800 Cergy Saint-Christophe - FRANCE

- 1 -

NEDERLANDS

2DISCOVER YOUR PHOTO EASY 155 PRINTER

PHO

EASY

155

Place the box in front of you, open the packaging and check that you have received the items listed below:

1 PHOTO EASY 155 printer

2 User manual

3 CD-ROM with its applications

4 Film cartridge *

5 Photo paper (2 packs of 20 sheets)*

6USB cable

7 Paper tray

8 Power supply unit

9 Mains cable

10 xD card adapter

GEM

EASY 155

PHO

e id u

g r e

io t a

l i t

u t i

ivret

u s

'ut l

d e l

jzing

a M

saa ik

u ebr G

depending on model

- 2 -

3PREPARE YOUR PHOTO EASY 155 PRINTER

CONNECT THE MAINS SUPPLY

ENGLISH

Remark: When installing your printer near a wall or some other object, keep an open space of at least 4 inches at the

back of the printer, to make sure the movement of the sheet of paper being printed is not obstructed.

 Please refer to the safety instructions at the beginning of this user guide before making any

connections.

 Insert one end of the mains lead into the corresponding socket of the power supply.

 Connect the power supply to the printer as shown in the illustration below.

 Plug the other end of the power supply mains lead into a wall socket.  Switch on the printer by pressing the " I " on the on/off switch located at the back of the

printer. The green light comes on and three lines are displayed on the screen.

 Your printer features a SCSI Mass storage master USB connector (A) and a slave USB

connector (B). The latter is used for connection with a master terminal (PC, etc.).

FRANÇAIS

DEUTSCH

ESPAÑOL

ITALIANO

Remarque : To obtain the list of devices compatible with this USB port (A), visit the site www.sagem.com.

- 3 -

NEDERLANDS

FIRST RIBBON INSTALLATION

Remarque : Use DSR400 or DSR400T consumables only. These are specially designed to provide you with optimum print

rendering.

Switch on the printer. Wait 10 seconds for the printhead to lift, then:

1. Open the external flap located on the right-hand side of the printer.

2. Remove the protective foam.

3. Take the new ribbon out of its packaging and make sure that the film is stretched after removing the card (A).

4. Install the ribbon in the position shown in the illustration below.

5. Lift the locking lever and push in the film cartridge until it touches the back of the compartment the locking lever must be locked after insertion.

6. Close the external flap.

Warning - Never touch the film cartridge with your fingers. Make sure the cartridge is completely

inserted into the printer. Check that the green locking lever is correctly lowered.

Remarque : In the event of any difficulty, check that there are no foreign objects in the film cartridge compartment.

- 4 -

TO CHANGE THE RIBBON

Remarque : Use DSR400 or DSR400T consumables only. These are specially designed to provide you with optimum

Remark: If this last operation is not carried out, you will not be able to use the printer.

print rendering. For this purpose, the printer must read the chip card delivered with each consumable kit after any new kit installation.

Switch on the printer. Wait 10 seconds for the printhead to lift, then:

1. Take the SIM card delivered with the ribbon and the photo paper. Insert it in the drive located on the front panel of the printer. The SIM card is identified and read by the printer. At the end of the procedure, "40 or 120" is displayed on the screen.

2. Remove the SIM card.

3. Take the new ribbon out of its packaging and make sure that the film is stretched after removing the card (A).

4. Open the external flap located on the right-hand side of the printer.

5. Lift the locking lever and remove the used ink ribbon.

6. Install the ribbon in the position shown in the illustration below.

7. Lift the locking lever and push in the film cartridge until it touches the back of the compartment the locking lever must be locked after insertion.

8. Close the external flap.

ENGLISH

FRANÇAIS

DEUTSCH

ESPAÑOL

7 8

Warning - Never touch the film cartridge with your fingers. Make sure the cartridge is

completely inserted into the printer. Check that the green locking lever is correctly lowered.

Remark: In the event of any difficulty, check that there are no foreign objects in the film cartridge compartment.

- 5 -

ITALIANO

NEDERLANDS

LOADING PAPER

Protection sheet

1 - Pull the paper tray out of the printer.

2 - Open a pack of paper with the protection sheet on the top, insert it in the paper tray, making sure the

rectangle reserved for postage stamps is on the outside of the tray, that is, towards you.

3 - Remove the protection sheet.

4 - Line up the tray with its compartment and push it in slowly until the locking system clicks.

Warning - handle paper sheets by their pre-cut edges, never allow your fingers to come into contact

with the shiny surface before printing.

Your SAGEM PHOTO EASY 155 printer is now ready to print your digital photographs.

Warning - protect consumable items against prolonged exposure to light, humidly, heat and dust.

Respect the operation conditions set out (Refer to paragraph Technical data, page -29).Only use SAGEM brand consumable items designed for this printer. Make sure that a previously printed photograph has not been slipped inadvertently into a packet of blank pages; this could damage the ribbon of your printer.

Warning - Make sure that a previously printed photograph has not been slipped inadvertently into

a packet of blank pages; this could damage the ribbon of your printer.

- 6 -

4PRINTING FROM A MEMORY CARD

Your SAGEM PHOTO EASY 155 printer is designed to be used with or without a computer. This chapter describes printer operation without a computer.

Refer to the technical data table at the end of thi user manual to check whether your memory card is compatible with the printer. In the event of incompatibility, use a computer and the image processing software supplied on the CD-ROM.

Warning - Small sized images, less than 80,000 pixels, cannot be printed from memory cards

(for example: an image size 320 x 240, equivalent to 76,800 pixels, will not be included in the index). On the other hand, these photographs may be printed from a PC or by means of a wireless IR link (or Bluetooth optional equipment).

INSERT A MEMORY CARD

Insert your memory card into the corresponding slot, as shown in the illustrations below. Into the case of a xD card, introduce initially the adapter provided into the left slit then insert the card in the adapter.

Warning - SmartMedia, CONTACTS FACING UPWARDS.

Warning - The memory cards do not enter fully in the reader slot.

DO NOT USE FORCE UNDER ANY CIRCUMSTANCES. If a card does not enter properly, remove it and check that you are introducing it in the correct slot and with the right orientation.

ENGLISH

FRANÇAIS

DEUTSCH

ESPAÑOL

Slot compatible with

Smart Media (SM),

Memory Stick (MS),

Standard Digital (SD)

Multi Media Card (MMC) formats

XD card with its adapter

- 7 -

Slot compatible with Compact Flash format

ITALIANO

NEDERLANDS

+ 23 hidden pages