16
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always be
followed to reduce the risk of fire, electric shock, and/or injury to persons, including
the following:
1 Read all instructions and information in this instruction book and any other
literature included in this carton referring to this product before operating or using
this appliance.
2 Do not touch hot surfaces. Use handles or knobs.
3 To protect against fire, electric shock and personal injury do not immerse cord,
plugs or appliance in water or other liquid.
4 Close supervision is necessary when any appliance is used by or near children.
5 Unplug from outlet when not in use and before cleaning. Allow to cool before
putting on or taking off parts, and before cleaning the appliance.
6 Do not operate any appliance with a damaged cord or plug or after the appliance
malfunctions or has been damaged in any way. Return appliance to the nearest
authorized service centre for examination, repair or adjustment.
7 The use of accessory attachments not recommended by the appliance manufacturer
may result in fire, electric shock or personal injury.
8 Do not use outdoors.
9 Do not let cord hang over edge of table or counter, or touch hot surfaces.
10 Do not place on or near a hot gas or electric burner, or in a heated oven.
11 Always turn appliance “OFF”, then plug cord into the wall outlet. To disconnect,
turn switch to “OFF”, then remove plug from wall outlet.
12 Do not use appliance for other then intended household use.
13 Use extreme caution when using hot steam.
SAVE THESE INSTRUCTIONS
CAUTION
This appliance is for household use. Any servicing, other than cleaning and user
maintenance, should be performed by an authorized service centre. Do not immerse
base in water. To reduce the risk of fire or electric shock, do not disassemble the base.
There are no user serviceable parts inside. Repair should be done by authorized service
personnel only.
1 Check voltage to be sure that the voltage indicated on the nameplate agrees with
your voltage.
2 Never use warm or hot water to fill the water tank. Use cold water only.
3 Keep your hands and the cord away from hot parts of the appliance during
operation.
4 Never clean with scouring powders or hard implements. Simply use a soft cloth
dampened with water.
5 To avoid your coffee maker scaling up, use purified or bottled water.
INSTRUCTIONS FOR THE POWER SUPPLY CORD
A A short power-supply cord is provided to reduce risks of getting tangled up or
tripping over a longer cord.
B Longer extension cords are available and may be used if care is exercised in their use.
C If a long extension cord is used:
1 the marked electrical rating of the extension cord should be at least as great as
the electrical rating of the appliance.
2 if the appliance is of the grounded type, the extension cord should be a
grounding type
3 the cable does not hang from the table to avoid the risk of getting caught up in it.
17
GENERAL INFORMATION
The coffee machine is suitable to make espresso coffee using coffee beans and is
equipped with a device for the distribution of steam and hot water.
This elegantly styled machine is designed for household use only. It is not suitable
for continuous professional-type use.
Warning. The manufacturer shall accept no liability for damage or injury
caused by:
• improper use or use for other than the intended purposes;
• repairs carried out by anyone other than an authorised service centre;
• tampering with the power cord;
• tampering with any machine component;
• use of spare parts and accessories other than those supplied by the
manufacturer.
The warranty will be invalidated in such cases.
TO FACILITATE INTERPRETATION
A warning triangle draws attention to the instructions that are important for user safety. Please carefully abide by these instructions to
avoid serious injury!
HOW TO USE THESE OPERATING INSTRUCTIONS
Keep these operating instructions in a safe place and make them available to
anyone else who should use the coffee machine. For further information or an
explanation of problems not completely or sufciently addressed in these instructions, contact an authorised service centre.
TECHNICAL SPECIFICATIONS
• Voltage rating See rating plate on appliance
• Power rating See rating plate on appliance
• Casing material Metal
• Size (w x h x d) (mm) 285 x 375 x 400
• Weight (Kg) 9
• Cord length (mm) 1200
• Control panel Front (Digital)
• Water tank (lit.) 2 - Extractible
• Power supply See rating plate on appliance
• Pump pressure (bars) 15
• Boiler Stainless steel
• Coffee container capacity (g.) 300 of coffee beans
• Grinders Ceramic
• Quantity of ground coffee 8 g
• Dreg drawer capacity 13
• Safety devices Boiler pressure safety valve
safety thermostat
Subject to engineering and manufacturing changes as warranted by technological
developments.
Machine in conformity with European Directive 89/336/EEC (Italian Legislative
Decree 476 of 04/12/92) concerning electromagnetic compatibility.
ENGLISH
SAFETY RULES
18
IN THE EVENT OF AN EMERGENCY
Immediately unplug the appliance.
THE APPLIANCE MAY ONLY BE USED
- In a closed place.
- To prepare coffee, dispense hot water, froth milk or heat beverages using
steam.
- For household use.
- By adults in full possession of their physical and mental capacities.
NEVER USE THE APPLIANCE
for purposes other than those indicated above to avoid hazards.
Never place any substances in the containers other than those specied in the
instruction manual. When you ll a container, make sure all nearby containers
are closed.
Fill the water tank only with fresh drinking water: hot water and/or other liquids
may damage the machine. Do not use carbonated water. The coffee grinder may
be adjusted only while it is running. Do not introduce your ngers or any material
other than coffee beans into the coffee grinder. Before attempting to access the
inside of the coffee grinder, switch OFF the machine and remove the plug from
the electric socket.
MAINS CONNECTION
Connect the coffee machine to a suitable electric socket. The voltage must match
the voltage specied on the appliance rating plate.
INSTALLATION
- Choose a perfectly level supporting surface. Do not place on a hot surface!
- Maintain a distance of 10 cm from walls and electric or gas burners.
- Do not keep at temperatures below 0 °C; the appliance may be damaged by
freezing.
- The electric socket must be accessible at all times.
- The power cord must not be damaged, secured with clamps, placed on very hot
surfaces etc.
- Do not let the power cord hang loosely (Warning: danger of tripping or of
causing the appliance to fall).
- Do not use the power cord to carry or pull the coffee machine.
HAZARDS
- The appliance must not be used by children or by individuals unacquainted with
the operating instructions.
- The appliance is dangerous for children. If left unattended it must be
switched off.
- Do not leave the materials used to pack the appliance within children’s reach.
- Do not direct a jet of hot steam and/or hot water toward yourself or others:
danger of scalding.
- Do not introduce any objects through the openings in the appliance (Electrical
hazard!).
- Do not touch the plug when your hands or feet are wet. Do not unplug the
appliance by yanking at the power cord.
- Warning: contact with hot water, steam or and hot water/steam nozzle may
cause burns.
FAULTS
- Do not use the appliance if it malfunctions or you suspect damage, e.g.
after a fall.
- Repairs must be performed by an authorised service centre.
- Do not use an appliance with a defective power cord. The cord may be replaced
exclusively by a service centre (Electrical hazard!).
- Switch off the appliance before opening the service door. Danger of burns!
CLEANING / DESCALING
- Before cleaning the appliance, unplug it and allow it to cool down.
- Avoid exposing the appliance to splashes of water. Do not immerge it in water.
- Do not dry machine components in a conventional or microwave oven.
SPARE PARTS
To guarantee safety, you should use only original spare parts and accessories.
DISPOSAL
- The packing materials can be recycled.
- Appliance: unplug the appliance and cut the power cord.
- Deliver the appliance and power cord to a service centre or public waste
disposal facility.
19
Coffee bean container
Cup plate
Control panel
Service door
SBS
Height and depth
adjustable brew unit
Drip tray + grill
Tray full indicator
Brew group
Dregs drawer
Swivel base
Coffee bean container lid
Water tank lid
Coffee temperature
ready indicator lights
“Aqua Prima” lter replacement light – see page 27
Steam indicator light
Water tank
Steam knob
Hot water/ steam tube
ON/OFF switch
Grind adjustment knob
Cleaning brush Brew group key
Cartridge lter
applicator
“Aqua Prima”
cartridge lter
Knob to adjust the quantity
of coffee in the cup
Selector button for 1 coffee
Selector button for 2 coffees
Alarm indicator light
Steam button
“Aqua Prima” lter alarm
reset
ENGLISH
INSTALLATION / CIRCUIT LOADING
20
The messages displayed by the machine during operation are shown
on pg.28.
Check that all components
are correctly placed.
Move the ON/OFF switch
to “I” to turn on the
machine.
Fill the coffee bean container
with coffee beans.
The machine is warming
up; lights are ashing.
The “Aqua Prima” lter can
be installed (see pg.27).
Place a container beneath
the steam tube.
Important warning for using the “Aqua Prima Filter” can be found at
page 28.
See rating plate
Fill the tank with fresh drinking water.
Turn the knob counterclockwise to start loading the
circuit.
Note: You must load the circuit before starting up the
machine for the first time, if it has been inoperative for a
lengthy period or if the water tank has been completely
emptied. The circuit must be also loaded each time
the light is steadily lit:
Insert the plug into a suitable electric socket.
Wait until a steady stream
of water ows out from the
nozzle.
Turn the knob clockwise
to terminate the circuitloading process.
Remove the container.
When lights remain steadily
lit, the machine is ready
for use.
Check the dater on “Aqua Prima” filter; if filter is past its
date, replace it with a new one.
ADJUSTMENT
COFFEE GRINDER
The neness of the grind may be
adjusted using the knob.
Coffee ows out too slowly.
Press and turn.
Coffee ows out too fast.
Press and turn.
ADJUSTMENTS
Adjustment may be made only while the coffee grinder is
operating.
Use coffee bean blends for espresso coffee makers. If you do not obtain
the desired result, try using different coffee blends. Store coffee in a cool
place, in a hermetically sealed container.
You will note a change after dispensing 1 - 2 coffees.
If you set the grinder on too ne a grind (knob turned all the way
anticlockwise) and the SBS control on “strong” (toward the right), coffee
may ow out in a slow trickle or not at all.
21
ENGLISH
COFFEE IN CUPS - You must adjust the dose before dispensing coffee.
This adjustment will have an immediate effect on the coffee brewed.
COFFEE IN CUPS
To adapt the quantity of coffee
brewed to the dimensions of cups.
For machines provided with SBS only. - To adjust the strength and consistency of brewed coffee.
The adjustment can also be made while brewing the coffe. This adjustment will have an immediate
effect on the coffee brewed.
Short coffee Weak black coffee
SBS
Espresso coffee
Strong black coffeeCafé crème
BIG CUPS
To place the brew unit again in its position, pull it until it ts in.
BIG CUPS
To use big cups, press the button and push the brew
unit until the end.
COFFEE DISPENSING / HOT WATER
22
Warning! Hot water and steam may cause burns! Direct the steam tube toward the drip tray.
1 COFFEE
COFFEE BEANS
Make sure that the machine is ready.
Position a warm coffee cup
beneath the brew unit.
2 COFFEES
COFFEE BEANS
Make sure that the machine is ready.
Position the warm coffee
cups beneath the brew
unit.
Press the button to brew
1 coffee.
Press the button to brew 2
coffees.
To stop brewing sooner,
press the button or turn the
knob.
To stop brewing sooner,
press the button or turn the
knob.
When the machine stops
making the coffee, remove
the cup.
When the machine stops
making the coffee, remove
the cups.
HOT WATER
Place a container beneath
the steam tube.
Turn the knob counterclockwise to start dispensing
water.
Wait. When you reach the
desired amount, close the
knob.
Remove the container.
Warning! Hot water and steam may cause burns! Direct the steam tube toward the drip tray.
CAPPUCCINO
23
CAPPUCCINO
Fill a cup to 1/3 with cold
milk.
Position the cup containing
milk beneath the steam
tube.
Press the button to restore the
machine to normal operation.
Lights are ashing.
Press the button to select
the function.
The light is ashing.
Open the knob to release
steam.
Place a container beneath
the steam tube.
When the light is steadily
lit, the machine is ready to
release steam.
Move the cup in a circular
fashion to heat the milk
evenly.
Open the knob and dispense hot water.
Open the knob to discharge
any residual water.
After frothing the milk,
close the knob.
When lights remain steadily
lit, close the knob and
remove the lid.
ENGLISH
When only steam comes
out, close the knob.
Remove the cup.
Dispense coffee into the
cup to prepare a delicious
cappuccino.
24
STEAM
Warning! Hot water and steam may cause burns! Direct the steam tube toward the drip tray.
STEAM
Check the machine status. Press the button to select
Take and place the
container beneath the hot
water/steam tube.
Press the button to restore the
machine to normal operation.
Lights are ashing.
the function.
The light is ashing.
Open the knob to release
steam.
Place a container beneath
the steam tube.
When the light is steadily
lit, the machine is ready to
release steam.
Move the container in a
circular fashion to heat
evenly.
Open the knob and dispense hot water.
Open the knob to discharge
any residual water.
After you have nished,
close the knob.
When lights remain steadily
lit, close the knob and
remove the lid.
When only steam comes
out, close the knob.
Remove the container.
The machine is ready to
brew coffee or dispense
hot water.
DESCALING
25
Warning! Never use vinegar as a descaling agent. You can use any
commercially available non-toxic, non-harmful descaling product for coffee
machines. We recommend using a Saeco descaling agent.
The machine must be
descaled every 2 months.
Remove the lter, see
page 27.
Dispense the descaling
solution into the receptacle.
Switch off the machine. Place a large receptacle
After about 30 seconds
close the knob.
Fill the water tank with the
descaling solution.
Switch off the machine and
remove the receptacle.
Descaling is necessary every 2 months; should water be very hard, descale the
machine more frequently. The machine must be on; it automatically controls the
distribution of the descaling solution.
beneath the steam
tube.
Whether there is
descaling solution
Switch on the machine.
A
Open the knob.
The descaling process
starts.
in the tank.
Check
Whether the tank is
empty.
After 10 minutes, follow
instructions (A) or (B)
B
Switch on the machine.
circuits must be rinsed. Type “B” routing.
Rinse out the tank and ll it
with fresh drinking water.
If the descaling cycle is interrupted,
the water tank and internal machine
ENGLISH
Place a large receptacle
beneath the steam tube.
Open the knob to rinse.
If the receptacle lls,
empty it.
When no water is left, turn
the knob to close the valve.
Remove the container.
After descaling the machine, reload the
machine circuit. Install the cartridge filter
again in the water tank.
CLEANING AND MAINTENANCE
26
Do not dry the machine and/or its components in a microwave and/or
conventional oven.
BASIC
CLEANING
Turn the machine off.
Unplug the machine.
Remove the brew unit and
wash it with water.
Wash the water tank.
Wash the lter inside it.
Clean the machine, its components, and the brew group
once a week at least.
Do not immerge the machine in water and do not place any of its
components in a dishwasher.
Remove the drip tray, empty it out and wash it.
Remove the dregs drawer,
empty it out and wash it.
Remove the “pannarello”
and clean it.
BREW GROUP
Open the front door. Remove the drip tray and
the dregs drawer.
Press the PUSH button to
release the brew group.
Unscrew the upper lter
and wash it.
Fit the lter back in place
when clean.
Wash the unit, dry it and
t it back in place. Do not
press the “PUSH” button.
Set all machine components
back in position.
Close the door.
“AQUA PRIMA” CARTRIDGE FILTER
The filter must be replaced when signalled by the machine, see page 28. Before descaling, remove the filter from the tank.
27
INSTALLATION
Remove the lter from the
packing container.
The reference must be
positioned in correspondence with the groove.
Open the knob and dispense water.
Adjust the dater to the
current month.
Press until the end limit. Turn the applicator coun-
Empty the water tank out at
intervals.
Insert the applicator and
turn it clockwise to secure
it to the lter.
ter-clockwise and remove
it from the tank.
When the tank is empty, ll
it again with fresh drinkable
water.
Check where the lter
positioning and reference
mark is.
Fill the tank with fresh
drinkable water.
Press the button. When
the light ashes, release
the button.
ENGLISH
Put the lter into the empty
tank.
Position a container beneath the steam tube and
turn the machine on.
It is possible to use the
machine without lter,
Saeco suggests its
use. If lter is not used,
the machine must be
descaled more frequently.
You can now use your
coffee machine.
DISPLAY MESSAGES - NOTES ON THE AQUA PRIMA CARTRIDGE FILTER
28
The control panel display guides users and helps them to use the machine correctly.
Fill the coffee bean container with coffee
Steadily lit
Important note: the dregs drawer may be emptied only when the machine
is on. The drawer must be removed for at least 5 seconds. If you empty the
drawer with the machine off, you will not be able to dispense coffee the next
time you switch the machine on.
Flashing
Steadily lit
beans and start the coffee brewing cycle.
Fill the water tank with fresh drinking water
and load the circuits.
Load the circuit.
Empty the dregs drawer.
Fit the brew unit properly in place.
Fit the drip tray and dregs drawer properly
in place.
Close the front door.
Replace the water lter in the tank.
After replacing the lter in the tank, reset the
alarm by pressing the button for 5 seconds
until the light goes off.
ADDITIONAL INFORMATION FOR CORRECTLY USING
THE “AQUA PRIMA” FILTER.
Please follow these simple instructions to correctly use the “Aqua prima” lter:
1. Keep the “Aqua prima” lter cool and away from sunlight; the room temperatu-
re should be between +5°C and +40°C;
2. Do not use the lter in temperatures over 60°C.
3. If the coffee machine is not used for 3 days, we recommend washing the
“Aqua prima” lter;
4 If the coffee machine is not used for more than 20 days, it is advisable to
replace the lter.
5. To store an already opened lter, seal it in a nylon bag and keep in the fridge;
do not store it in the freezer to avoid damaging the lter properties.
6. Before using the lter, leave it to soak in the water tank for 30 minutes.
7. Once it is taken out of its pack, do not keep the lter in the open air.
8. The lter must be replaced 90 days after opening the packing or after treating
60 litres of drinking water.
Flashing
Too high boiler temperature, load the circuit.
Let water ow out.
PROBLEMS - CAUSES - REMEDIES
29
PROBLEMS CAUSES REMEDIES
The machine does not
turn on.
The coffee is not hot
enough.
The machine does not
brew coffee.
No hot water or steam is
dispensed.
A noise can be heard
coming from the steam
tube of the machine.
The machine is not
connected to the power
supply.
The cups are cold. Warm up the cups.
Knob positioned on too
low a setting
The tube nozzle is clogged.
Move the main switch to ON.
Check the plug and the
connection
Turn the knob clockwise to a
higher setting.
Clean the nozzle opening with
a needle.
closed and the machine
must be off.
During this operation,
the knob must be
PROBLEMS CAUSES REMEDIES
Coffee ows out in slow
trickle or not at all.
Excessively ne grind
and SBS control turned
to the right.
Adjust to a coarser grind (turn
the knob clockwise).
Turn the SBS control toward
the left.
ENGLISH
The machine takes a long
time to warm up.
The brew unit cannot be
removed.
Excessive scale has
built up.
The unit has stopped in
the wrong position.
Descale the machine.
Close the door and switch on
the machine; the brew unit will
move back into position.
30
WICHTIGE VORSICHTSMASSNAHMEN
Bei der Verwendung von Elektrogeräten empfiehlt es sich, sich an einige Vorsichtsmaßnahmen
zu halten, um die Gefahr von Brand, elektrischen Schlägen und Unfällen einzuschränken.
1 Alle in diesem oder jedem anderen in der Verpackung enthaltenen Heft
angegebenen Anweisungen und Informationen aufmerksam durchlesen, ehe die
Espressomaschine eingeschaltet oder benutzt wird.
2 Keine heißen Flächen berühren.
3 Netzkabel, Stecker oder den Maschinenkörper nicht in Wasser oder andere
Flüssigkeit tauchen, um Brand, elektrische Schläge und Unfälle zu vermeiden.
4 Im Beisein von Kindern die Espressomaschine mit besonderer Vorsicht handhaben.
5 Den Stecker aus der Steckdose ziehen, sobald die Maschine nicht mehr benutzt
wird oder gereinigt wird. Bevor Teile entnommen oder eingesetzt werden sowie vor
der Reinigung die Maschine abkühlen lassen.
6 Keine kaputten oder defekten Geräte oder Geräte mit beschädigtem Netzkabel
oder –stecker verwenden. Das schadhafte Gerät beim nächsten Händler oder
Kundendienst prüfen, reparieren oder neu einstellen lassen.
7 Die Verwendung nicht vom Hersteller empfohlenen Zubehörs kann Brand,
elektrische Schläge und Unfälle verursachen.
8 Die Espressomaschine nicht im Freien verwenden.
9 Das Kabel darf nicht vom Tisch herunterhängen oder heiße Flächen berühren.
10 Die Espressomaschine nicht in der Nähe von heißen Küchenherden oder Backöfen
verwenden.
11 Prüfen, ob die Maschine sich in Stellung „0” befindet, bevor man den Stecker einsteckt.
Zum Ausschalten auf „0” stellen, dann den Stecker aus der Steckdose ziehen.
12 Die Maschine nur im Haushalt verwenden.
13 Bei Verwendung von heißem Dampf mit äußerster Vorsicht verfahren.
DIESE ANWEISUNGEN GUT AUFBEWAHREN
HINWEISE
Diese Espressomaschine wurde ausschließlich für den Haushalt entwickelt. Sämtliche
Eingriffe mit Ausnahme der Reinigung oder normalen Wartung dürfen ausschließlich durch
den autorisierten Kundendienst vorgenommen werden. Das Gerät nicht in Wasser tauchen.
Reparaturen dürfen nur durch Fachpersonal des autorisierten Kundendienstes erfolgen.
1 Sicherstellen, dass die auf dem Datenschild des Geräts angegebene Spannung mit
der Ihres Netzanschlusses übereinstimmt.
2 Nie lauwarmes oder heißes Wasser in den Wasserbehälter füllen. Ausschließlich
kaltes Wasser verwenden.
3 Während des Betriebs nie die heißen Teile oder das Netzkabel der Maschine berühren.
4 Keine Schleif- oder Scheuermittel zum Reinigen verwenden. Es genügt ein weicher
Lappen mit Wasser.
5 Zur Vermeidung von Kalkablagerungen kohlensäurefreies Mineralwasser verwenden.
BETRIEBSANLEITUNGEN ZUM NETZKABEL
A Das mitgelieferte Netzkabel ist relativ kurz, damit es sich nicht verdrehen kann
oder Sie darüber stolpern.
B Längere Netzkabel können verwendet werden, doch sollte man dabei mit grösste
Vorsicht vorgehen.
C Sollte ein längeres Netzkabel verwendet werden, folgendes überprüfen:
1 dass die auf der Verlängerungsschnur vermerkte Spannung mindestens der des
Elektrogerätes entspricht;
2 dass es einen Stecker mit drei Stiften (Erdung) hat, falls das Netzkabel des
Elektrogerätes ebenfalls drei hat;
3 Das Netzkabel darf nicht am Tisch herunterhängen; Sie könnten darüber
stolpern.
Loading...