Rockwell Automation 2711p-RAK15, 2711p-RAT15 User Manual [en, de, es, fr, it]

Installation Instructions

Adapter Kit for PanelView 1400e Touch Terminal Cutout

Catalog Number 2711P-RAK15, 2711P-RAT15

Language Page

English 3

Français 7

Deutsch 11

Español 15

Italiano 19

Português 23

Publication 2711P-IN011C-MU-P - March 2007

2 Adapter Kit for PanelView 1400e Touch Terminal Cutout

Important User Information

Solid state equipment has operational characteristics differing from those of electromechanical equipment.
Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls (publication
SGI-1.1 available from your local Rockwell Automation sales office or online at
http://literature.rockwellautomation.com
equipment and hard-wired electromechanical devices. Because of this difference, and also because of the
wide variety of uses for solid state equipment, all persons responsible for applying this equipment must
satisfy themselves that each intended application of this equipment is acceptable.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages
resulting from the use or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many
variables and requirements associated with any particular installation, Rockwell Automation, Inc. cannot
assume responsibility or liability for actual use based on the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits,
equipment, or software described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell
Automation, Inc., is prohibited.

Throughout this manual, when necessary, we use notes to make you aware of safety considerations.

) describes some important differences between solid state

WARNING

IMPORTANT

ATTENTION

SHOCK HAZARD

BURN HAZARD

Identifies information about practices or circumstances that can cause an explosion in
a hazardous environment, which may lead to personal injury or death, property
damage, or economic loss.

Identifies information that is critical for successful application and understanding of
the product.

Identifies information about practices or circumstances that can lead to personal injury
or death, property damage, or economic loss. Attentions help you to identify a hazard,
avoid a hazard, and recognize the consequences.

Labels may be on or inside the equipment, for example, a drive or motor, to alert
people that dangerous voltage may be present.

Labels may be on or inside the equipment, for example, a drive or motor, to alert
people that surfaces may reach dangerous temperatures.

Publication 2711P-IN011C-MU-P - March 2007

Installation Instructions

Adapter Kit for PanelView 1400e
Touch Terminal Cutout

Catalog Numbers 2711P-RAK15, 2711P-RAT15

English

Topic Page

About This Publication 3

Package Contents 4

Tools Required 4

Disconnect Power to the Terminal 4

Remove the Existing Terminal 4

Attach the Adapter Plate to the Panel 5

Attach Terminal to the Adapter Plate 6

About This Publication

This document provides procedures on how to mount the following devices into an
existing PanelView 1400E cutout:

• PanelView Plus 1500

• PanelView Plus CE 1500

Cat. No. This New Terminal: Fits into Existing Cutout for:

2711P-RAK15 PanelView Plus 1500 Keypad, or Keypad and Touch

PanelView Plus CE 1500 Keypad, or Keypad and Touch

2711P-RAT15 PanelView Plus 1500 Touch

PanelView Plus CE 1500 Touch

The cutout adapter is designed to fit into an existing cutout using stud mounts.

Publication 2711P-IN011C-MU-P - March 2007

PanelView 1400e Keypad
2711E-K14xxx

PanelView 1400e Touch
2711E-T14xxx

4 Adapter Kit for PanelView 1400e Touch Terminal Cutout

Package Contents

The cutout adapter kit includes:

• cutout adapter plate with gasket and ball bearing spacers

• 18 #10-32 nuts with flat washers for 1500 keypad

• 12 #10-32 nuts with flat washers for 1500 touch

Tools Required

These tools are required for installation:

• socket driver with 3/8 inch socket

• slot or Phillips screwdriver

• torque wrench capable of 10 lb-in

Disconnect Power to the Terminal

1. Disconnect power at the source and remove the power cord from the

PanelView terminal.

2. Disconnect all communication cables from the terminal.

ATTENTION

Make sure the power cord of the PanelView terminal is disconnected and that
all cables have been disconnected from the terminal.

Remove the Existing Terminal

1. Remove the nuts and washers that secure the terminal in the panel and save

them for the adapter plate installation.

2. Slide the existing terminal out from panel.

Publication 2711P-IN011C-MU-P - March 2007

Adapter Kit for PanelView 1400e Touch Terminal Cutout 5

Attach the Adapter Plate to the Panel

1. Align the studs on the cutout adapter plate with the existing stud holes on

the front of the panel.

2. Place the adapter plate into the front of the panel cutout until the sealing

gasket material is firmly against the front of the panel.

Adapter Plate

Nut and Washer

Front of Panel or Enclosure

Inside of Panel or Enclosure

3. Using nuts with flat washers, fasten the cutout plate onto the studs until the

sealing gasket is slightly compressed against the front of the panel.

4. Using the torque wrench, tighten the nuts to not more than 1.92 Nm (17

lb-in) to maintain a NEMA Type 4X rating.

Do not overtighten.

Publication 2711P-IN011C-MU-P - March 2007

6 Adapter Kit for PanelView 1400e Touch Terminal Cutout

Attach Terminal to the Adapter Plate

1. Insert the new terminal into the front of the enclosure until the terminal

gasket is flush with the adapter plate.

2. Install the 8 mounting clips (2 top, 2 bottom, 2 on each side).

The ends of the mounting clips slide into the slots on the terminal. The top
or bottom clips tighten directly to the adapter plate.

Adapter Plate

Mounting Clip

3. Tighten the screws on the mounting clips by hand until the gasket seal

contacts the mounting surface uniformly.

4. Using the torque wrench, tighten the screws on the mounting clips to the

proper torque rating provided in the installation instructions for the new
terminal.

This is necessary to maintain a NEMA Type 4X rating. Do not overtighten.

ATTENTION Tighten the mounting clips to the specified torque to provide a proper seal and

to prevent potential damage to the product. Allen-Bradley assumes no
responsibility for water or chemical damage to the product or other equipment
within the enclosure because of improper installation.

Publication 2711P-IN011C-MU-P - March 2007

Notice d’installation

Kit d’adaptation de découpe pour terminal
PanelView 1400e à dalle tactile

Catalog Numbers 2711P-RAK15, 2711P-RAT15

Français

Pour les informations suivantes Voir page

Description 7

Contenu du kit 8

Outils nécessaires 8

Déconnexion du terminal 8

Retrait du terminal existant 8

Fixation de la plaque d’adaptation sur le panneau 9

Fixation du terminal sur la plaque d’adaptation 10

Description

Ce document indique comment monter les équipements suivants dans une
découpe existante prévue pour un PanelView 1400e.

• PanelView Plus 1500 ;

• PanelView Plus CE 1500.

Réf. Ce nouveau terminal S’insère dans une découpe

2711P-RAK15 PanelView Plus 1500 à clavier ou à clavier et dalle tactile

PanelView Plus CE 1500 à clavier ou à clavier et dalle
tactile

2711P-RAT15 PanelView Plus 1500 à dalle tactile

PanelView Plus CE 1500 à dalle tactile

Ce kit d’adaptation se monte dans une découpe existante à l’aide de goujons.

Publication 2711P-IN011C-MU-P - March 2007

destinée au

PanelView 1400e à clavier
2711E-K14xxx

PanelView 1400e à dalle tactile
2711E-T14xxx

8 Kit d’adaptation de découpe pour terminal PanelView 1400e à dalle tactile

Contenu du kit

Le kit d’adaptation contient les éléments suivants :

• plaque d’adaptation pour découpe avec joint d’étanchéité et espaceurs à
roulement à billes ;

• 18 écrous n° 10-32 avec rondelles plates pour les terminaux 1500 à clavier ;

• 12 écrous n° 10-32 avec rondelles plates pour les terminaux 1500 à dalle

tactile.

Outils nécessaires

Vous aurez besoin des outils suivants pour monter la plaque d’adaptation :

• une clé à douille avec douille de 3/8 pouce ;

• un tournevis plat ou cruciforme ;

• une clé dynamométrique.

Déconnexion du terminal

1. Déconnectez l’alimentation à la source et débranchez le cordon

d’alimentation du terminal PanelView.

2. Déconnectez tous les câbles de communication du terminal.

ATTENTION

Assurez-vous que le cordon d’alimentation du terminal PanelView est
déconnecté et que tous les autres câbles sont déconnectés du terminal.

Retrait du terminal existant

1. Retirez les écrous et les rondelles qui maintiennent le terminal sur le

panneau et mettez-les de côté : vous les réutiliserez pour installer la plaque
d’adaptation.

2. Retirez le terminal du panneau.

Publication 2711P-IN011C-MU-P - March 2007

Kit d’adaptation de découpe pour terminal PanelView 1400e à dalle tactile 9

Fixation de la plaque d’adaptation sur le panneau

1. Alignez les goujons de la plaque d’adaptation sur les trous existants sur le

panneau.

2. Placez la plaque d’adaptation dans la découpe du panneau jusqu’à ce que le

joint soit bien positionné contre l’avant du panneau.

Plaque d’adaptation

Ecrou et rondelle

Avant du panneau ou de
l’armoire

Intérieur du panneau ou
de l’armoire

3. Fixez la plaque d’adaptation sur les goujons à l’aide des écrous et des

rondelles plates en les serrant jusqu’à ce que le joint d’étanchéité soit
légèrement comprimé contre le panneau.

4. Utilisez la clé dynamométrique pour serrer les écrous avec un couple de

serrage d’1,92 Nm maximum pour rester conforme à la classification NEMA
type 4X.

Veillez à ne pas trop les serrer.

Publication 2711P-IN011C-MU-P - March 2007