RocketFish RF-TVMFM01 User Manual
RF-TVMFM01_10-0451_QSG_V2_EN_finalLR.pdf 1 8/23/2011 11:56:36 AM
QUICK SETUP GUIDE
RF-TVMFM01
1 Install the arm assembly
Option 1: Installing to a wood stud wall
Note: Any material covering the wall must not exceed 16 mm (5/8 in.).
1 Locate the stud. Verify the center of the stud with an awl or
thin nail or use an edge-to-edge stud nder.
2 Level the arm assembly (A) and mark the hole locations.
3 Drill pilot hole to a depth of 75 mm (3 in.) using a
5.5 mm (7/32 in.) diameter drill bit.
4 Align the arm assembly (A) with the
pilot holes, insert the coach screws (G)
through the holes in the arm
assembly, then tighten
the coach screws only until
they are pulled rmly
against the arm assembly.
CAUTION: Avoid potential
injuries or property damage!
DO NOT over-tighten the
coach screws (G).
<16 mm
(5/8 in.)
2 Attach the mounting hardware
Option 1: For TVs with inset mounting or that require extra space for wires
Install spacers (E), washers (D), and screws (C) into the top two holes in the back of the TV.
Leave a gap between the spacer and the washer and screw.
Note: Only install the hardware in the top two screw holes at this time. The remaining hardware
will be installed in Step 3.
Thank you for choosing the Rocketsh RF-TVMFM01.
The RF-TVMFM01 TV mount is designed to support a
at-panel TV weighing up to 15.8 kg (35 lbs.).
Package contents
A Arm assembly (1)
M4 bag
B M4 × 12 mm screws (4)
C M4 × 30 mm screws (4)
D M4 washers (4)
E M4 spacers (4)
Hex key bag
F 4 mm (5/32 in.) hex key (1)
Coach Screw bag
G 8 mm (5/16 in.)× 70 mm
(2 3/4 in.) coach screw (2)
H Concrete anchor (2)
M4 bag
M4 × 12 mm
M4 × 30 mm
Wall
203.2 mm
(8 in.)
8 in.
TV
139.7 mm
(5-1/2 in.)
TV shifts 139.7 mm (5-1/2 in.) in. from the
home position to full extension.
Option 2: Installing to a solid concrete or concrete block wall
1 Level the arm assembly (A) and mark the hole locations.
2 Drill pilot hole to a depth of 75 mm (3 in.) using a
9.5 mm (3/8 in.) diameter drill bit.
3 Insert the concrete wall anchors (H) into the pilot holes
and make sure that the anchors are seated ush with
the concrete surface.
4 Align the arm assembly (A) with the anchors, insert
the coach screws (G) through the holes in the arm assembly,
then tighten the coach screws only until they are pulled
rmly against the arm assembly.
CAUTION:
Avoid potential injuries or property damage!
DO NOT over-tighten the coach screws (G).
75 mm
(3 in.)
Gap
NOTE: If the hole pattern on
your TV is 75 mm x 75 mm the
washers (D) will not be used.
Option 2: For at backed TVs
Install washers (D), and screws (B) into the top two holes in the back of the TV.
Leave a gap between the back of the TV and the washer and screw.
Note: Only install the hardware in the top two screw holes at this time. The remaining hardware
will be installed in Step 3.
CAUTION: To prevent property
damage or personal injury, never
drill into mortar between blocks.
Mount wall plate directly onto the
concrete surface.
Cable ties
Hex key bag
4 mm
(5/32 in.)
Cable ties
Tools you will need:
• Stud nder
• Awl
• Pencil
• Level
• Tape measure
• Phillips screwdriver
• Hammer (concrete only)
Lag Bolt Bag
8mm (5/16 in.)× 70 mm (2 3/4 in.)
• Socket wrench with
12.7 mm (1/2 in.) socket
or adjustable wrench
• 5.5 mm (7/32 in.) wood drill bit
• 9.5 mm (3/8in.) masonry drill bit
(concrete only)
• Power drill
M4
M4
Gap
75 mm
(3 in.)
NOTE: If the hole pattern on
your TV is 75 mm x 75 mm the
washers (D) will not be used.
RF-TVMFM01_10-0451_QSG_V2_EN_finalLR.pdf 2 8/23/2011 11:56:42 AM
3 Mount the TV to the arm assembly
Option 1: For TVs with inset mounting or that require extra space for wires
1 Mount the TV by tting the top spacers, screws, and washers onto the
notches in the top of the arm assembly plate.
2 Install the bottom spacers (E), screws (C), and washers (D) into the bottom
holes.
3 Tighten all screws carefully until snug.
NOTE: If the hole pattern on
your TV is 75 mm x 75 mm the
washers (D) will not be used.
HEAVY! You will need
assistance with this step.
4 Adjust the angle of tilt
If necessary, adjust the tilt tension by hand or by using the hex key (F).
12°
20°
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
CAUTION: Do not use this product for any purpose not explicitly specied
by Rocketsh. Improper installation may cause property damage or
personal injury. If you do not understand these directions, or have doubts
about the safety of the installation, contact Customer Service or call a
qualied contractor. Rocketsh is not responsible for damage or injury
caused by incorrect installation or use.
The weight of your TV must not exceed 15.8 kg (35 lb. ). The wall must be
capable of supporting ve times the weight of the TV and wall mount
combined.
This product contains small items that could be a choking hazard if
swallowed. Keep these items away from young children!
E
Option 2: For at backed TVs
1 Mount the TV by tting the top screws and washers onto the notches
in the top of the arm assembly plate.
2 Install the bottom screws (B) and washers (D) into the bottom holes.
3 Tighten all screws carefully until snug.
5 Adjust the swivel tension
If necessary, adjust the swivel tension by using the hex key (F).
NOTE: If the hole pattern on
your TV is 75 mm x 75 mm the
washers (D) will not be used.
HEAVY! You will need
assistance with this step.
6 Manage the cables
Use cable ties (I) to bundle and secure the TV cables to the arm assembly.
5-year limited warranty
Visit www.rocketshproducts.com for details.
We’re here for you
www.rocketshproducts.com
For customer service, call:
0800 389 1120
© 2011 BBY Solutions, Inc., All Rights Reserved.
© 2011 Best Buy UK Distributions Limited. All rights reserved. Distributed
by Best Buy Europe Distributions Limited. 1 Portal Way, London W3 6RS
ROCKETFISH is a trademark of BBY Solutions, Inc. Registered in some
countries. All other products and
brand names are trademarks of their respective owners
6907-002029 <00>
UK ENGLISH 11-0451
Loading...