RKI Instruments GX-94 User Manual

Installation/Data Retrieval Instructions

GX-94/Eagle Data Retrieval Software, For Eagle

System Requirements

• PC-compatible computer which runs Windows 95, Windows 98, or
Windows NT

• CD-ROM drive

• 16 MB RAM minimum, 32 MB RAM recommended

Installation

1. Insert the GX-94/Eagle Data Retrieval Software CD into the CD-ROM
drive.

2. At the default Windows screen, click the Start button in the lower left
corner and select Run.

3. When the Run dialog box appears, enter D:\setup.exe in the Open
field and click OK. The Data Retrieval Software installation will begin.

NOTE: If your CD-ROM drive is designated as a drive other than D:\,

type in that drive when entering the file name. For example,
E:\setup.exe.

4. Follow instructions on the screen during the installation process.
When the installtion is complete, you may either launch the program or
return to the default Windows screen.

NOTE: The installation software installs the program in C:\Program

Files\RKI INSTRUMENTS\GX-94-EAGLE unless otherwise
specified. If you changed the destination or file folder names
during installation, please note this when starting the program
in Retrieving Data, item 4 below.

Retrieving Data

NOTE: Turn Eagle off before connecting the Data Retrieval Cable.

1. Connect the Data Retrieval Cable from a serial port on the computer,
either COM 1,COM 2, COM 3, or COM 4, to the datalogger port on the

Eagle.

2. Turn on the Eagle. The instrument will perform the battery voltage
check. Wait until the following message appears on the display
screen: PC TRANSMIT STAND BY OK.

3. At the default Windows screen, click the Start button in the lower left
corner.

RKI Instruments, Inc. Page 1 of 3

4. Select Programs and then GX-94 from the pop up menus to start the
program. The Main Screen appears. Alternatively, you can double
click GX94.exe where the program resides.

5. Once the program starts, click the UPLOAD button. The Upload
Screen appears.

6. Select the COM port you want to use to retrieve data in the Serial Line
Select box.

7. Select Eagle in the Instrument Select box.
NOTE: The software will put the data in the C:\Program Files\RKI

INSTRUMENTS INC\GX-94-EAGLE folder by default. If you
want to send the retrieved data to another folder, exit the
software and see the Storing Data to Different Folders section
below.

8. Click the START UPLOAD button to retrieve data from the Eagle.

9. When data retrieval is complete, click the CLOSE button. The Main
Screen appears with a list of all sessions retrieved from the Eagle.

10. Double click a session to view the Summary Screen for that Session.

11. At the Summary Screen, click the DETAILS button to see the Details
Screen. This screen shows all the data and events for a particular
session. It also allows graphing and printing.

- Click the GRAPH button to display the Detail Graph screen. This

screen shows a graph of the data. To print the graph, click the
PRINT button.

- Click the PRINT button to print the data in tabular form.

- Click the EXPORT button to export a fixed width format text file of

the data for the session. The file is sent to the same folder that the
data is sent. It can be opened by a spread sheet program such as
Microsoft Excel.

12. To exit the program, click the CLOSE button on each screen until you
reach the Main Screen. Then click the EXIT button to exit the program.

13. Turn off the Eagle. After the GOOD-BYE on the display screen
disappears, disconnect the data logging cable from the Eagle.

Storing Data to Different Folders

As mentioned above, the default location for retrieved data is in the
C:\Program Files\RKI INSTRUMENTS INC\GX94-EAGLE folder. If you
want to store the retrieved data in a different location, do the following:

1. Either by using My Computer or Windows Explorer, go to the
C:\Program Files\RKI INSTRUMENTS INC\GX94-EAGLE folder where

the software resides. Right click on GX94.exe.

RKI Instruments, Inc. Page 2 of 3