Rivera Primo 1097-000 User Manual
INSTRUCTIONS
12450 Whittier Blvd. Whittier Ca. 90602
(562)907-2600 Fax: (562)907-2606
www.riveraprimoinc.com
Kit Number
SPEEDO TWEAK TOOL
1097-0001
FOR ELECTRIC SPEEDOMETERS
hanging the gear ratio on some models will make the speedometer read
incorrectly. When the speedo reads incorrectly it can incapacitate the 6th gear
C
an electronic speedometer with the stock electric speed sensors to the correct reading.
The 1097-0001 has an adjustable range of correction from x2.84 times (more than
double) to x0.502 times (half). Calibration is set using the two button switches.
Press the UP button to increase the speed. Press the DOWN button to decrease
the speed. The 1097-0001 has an internal memory that stores the calibration when the
bike is off, or if the 1097-0001 is unplugged.(Unit must remain on vehicle after recalibration.)
indicator light and cruise control. The 1097-0001 will make it possible to adjust
Scan with your smart
phone to access
www.riveraprimoinc.com
Calibration
1a. In 6th gear. Press and hold the UP or DOWN
button while you are riding until the 6th gear
indicator light comes on. Your bike must be
moving to adjust the speedometer.
1b. Follow a vehicle going at a set speed or time
yourself riding one mile so you know what
your speed is. A GPS or Dyno are other good
ways to determine your speed.
2. Press and hold the UP or DOWN
button while you are riding to change the
reading on the speedometer until the accurate
speed is displayed. Your bike must be moving
to adjust the speedometer.
3. After the 1097-0001 has detected that no
buttons have been pushed for 10 seconds,
a new calibration will be stored.
Note:2004 and up Big Twin Motorcycles use a data bus to send information to the speedometer. The
1097-0001 needs to correct speed information before it goes into the ECM. To correct a speedometer
on a 2004 or newer bike, the 1097-0001 needs to be connected between the speed sensor and the
ECM to function properly .
Installation
2004 & up Sportsters and
all other models 2007 & up
1. Find the speed sensor wires coming from the
sensor. (The speed sensor is below the battery at
the back of the transmission nearly centered in the bike.)
2. After locating the speed sensor, follow the wires
up to the ECM. At an accessible point, cut the
wires and solder in the 1097-0001 as shown in
the diagrams on the following pages.
3. For 2007 model bikes with cruise control
You have to make the cut prior to where the white/
green wire is Teed into the cruise control module,
this is usually located about 3-4” after the speed
sensor plug at the sensor.
(see the wiring diagrams on next pages)
2006-09 Dyna, 2007 Touring & 2007-09 Softail
Before
Cruise
Control
ECM
White with
green stripe
White with
green stripe
Factory
installed split
Red with
White stripe
Black with
green stripe
White with
green stripe
VSS
Cut Here
After installing 1097-0001
Cruise
Control
ECM
White with
green stripe
White with
green stripe
Factory
installed split
Red with
White stripe
Black with
green stripe
White with
green stripe
Solder Joints
Black
Red
1097-0001
Red with
White stripe
Yellow
White with
green stripe
Black
Red
White
VSS
2008-2013 Touring
Before
Approx.
1.5”
ECM
White with
green stripe
Brown with
orange stripe
Black with
yellow stripe
Cut Here
After installing 1097-0001
Brown with
orange stripe
Solder Joints
Black
Black
Red
White
Red
Yellow
1097-0001
ECM
White with
green stripe
Brown with
orange stripe
Black with
yellow stripe
VSS
White with
green stripe
Black with
yellow stripe
Black
Red
Yellow
Black
Red
White
VSS
VSS wire color codes found on different models
VSS ground VSS signal VSS power
Softail
Dyna
Touring
Sportster
*Both red wires come from the same source.
**VSS= Vehicle speed sensor, ECM= Electronic control module
Limited Warranty
This product is covered by a limited warranty that it is free from defects in material and
workmanship, and against excessive wear for a period of one year. Our obligation under this
warranty is limited to the repair of replacement of its product only, and it is not responsible
for incidental and consequential damages, property damage or personal injury damages tot
he extent permitted by law. (Some states do not allow warranty limitation, so the above may
not apply to you). There is absolutely no warranty on any parts used in racing applications,
or on products that have been physically altered, improperly installed or maintained, used
in improper applications, abused or not used in conjunction with the proper parts. To make
a warranty claim, you must return the product freight prepaid to: Rivera Primo Inc., 12450
Whittier Blvd., Whittier, CA 90602 • 562-907-2600.
Black-Green White-Green or Lt Green-Yellow Red-White
Black or Black-Green White-Green Red-White
Black-Green or Black-Yellow White-Green
Red-White or Brown-Orange
Black Black-Blue Black-Red
1108-0032
Loading...