RISCO Group AC500R11 User Manual
Access Control Reader
W
W
R
R
+
+
B
G
G
G
D
-
W
D
-
D
S
S
O
G
G
B
R
R
Y
B
B
B
H
H
V
C
C
G
-
S
P
-
S
L
O
O
Model: AC500R11
RISCO Group’s Access Control Reader employs advanced RFID technology in a rugged
and stylish enclosure. The reader is compatible with 13.56 MHz RFID read-only tags,
read/write tags and smart encrypted data tags. Suitable for indoor and outdoor
installation with a rugged polycarbonate enclosure and molten epoxy for vandal
resistance. The reader is compatible to work with any standard access control system or
with RISCO Access Control (AxesPlus™ V1.19 and higher) using RS232 serial
communication.
Installation
1. The Access Control Reader can be mounted indoors or outdoors on any surface
(wood, metal, concrete, etc.).
2. Remove the cover from the reader.
3. Choose the required location and mark the installation holes and the wiring
passage hole while using the reader base as a template.
4. Drill a 12 mm hole for the cable passage and two installation holes, 4mm each.
5. Secure the reader to the surface using the supplied screws.
6. Route the cable to the controller and wire according to the Wiring section.
7. Replace the cover.
Wiring
Wire the reader to the controller according to the following wiring table and the controller installation
instructions.
ire
ed
lack
reen
hite
rain
range
rown
ellow
lue
iolet
ray
ink
ight Blue
iegand
DC
ND
ata0
ata1
hield GND
reen LED control
ed LED control
uzzer
old
ard present
-------------
------------ptional
LED & Buzzer Testing
The following table indicates the default LEDs and buzzer indications.
Operation Indication
Start Up Short LED blink and Buzzer beep will indicate successful device startup
Stand by mode Red LED will blink shortly every 5 sec to show that the reader is ON
Card present Buzzer will beep shortly for recognized cards only
Note:
Wiring buzzer control input (Yellow wire) to ground during device power on will put it in silent mode (except power on beep).
The buzzer is returned to its normal operation after restarting device with floating control input (Yellow wire).
Buzzer control input (Yellow wire) can be used for other purposes, for example “Door open too long” indication.
Once connected to the Access Controller, the LED and Buzzer operation will be controlled by the controller software.
S-232
DC
ND
-------------
------------hield GND
reen LED
ed LED
uzzer
old
ard present
erial TX
erial RX
ptional
Page 1
U
T
t
T
supp
B
T
supp
B
T
supp
P
T
supp
I
T
supp
F
T
supp
U
T
supp
C
T
supp
I
T
supp
Important Product Specifications
Input Voltage 8V to 28VDC
Current Consumption Average - 60mA Maximum - 150mA
Transmit Frequency 13.56MHz
Reading Distance
Up to 2.25 cm for card. Up to 1.2 cm for tag
Interface Wiegand, RS232
Audio/Visual Indication Internal Bi-Color LED and Buzzer
Operating Temperature -30°C to 65°C (-22°F to 149°F)
Storage Temperature -40°C to 85°C (-40°F to 185°F)
Operating Humidity 5% to 95% Non condensing
RFID protocols supported ISO14443A (DESFire)/ EV1
Default Wiegand output: Chip Serial Number (CSN) in 37bits format following specification of
HID (H10302) and STID (3F)
Physical characteristics
Material Polycarbonate
Dimensions (W x H x D) 60 x 80 x 20 mm (2.3 x 3.2 x 0.8 inch)
Maximum distance to Controller Wiegand: 60 m (200 ft)
RS232: 15 m (50 ft)
Recommended cable is ALPHA 1295 (22 AWG) 5 conductor stranded
with overall shield or equivalent
RTTE Compliance Statement
Hereby, RISCO Group declares that this equipment is in compliance with the essential requirements and other relevant
provisions of Directive 1999/5/EC. For the CE Declaration of Conformity please refer to our website: www.riscogroup.com.
RISCO Group Limited Warranty
RISCO Group and its subsidiaries and affiliates ("Seller") warrants its products to be free from defects in materials and
workmanship under normal use for 24 months from the date of production. Because Seller does not install or connect the
product and because the product may be used in conjunction with products not manufactured by the Seller, Seller can not
guarantee the performance of the security system which uses this product. Sellers' obligation and liability under this warranty is
expressly limited to repairing and replacing, at Sellers option, within a reasonable time after the date of delivery, any product not
meeting the specifications. Seller makes no other warranty, expressed or implied, and makes no warranty of merchantability or
of fitness for any particular purpose. In no case shall seller be liable for any consequential or incidental damages for breach of
this or any other warranty, expressed or implied, or upon any other basis of liability whatsoever. Sellers obligation under this
warranty shall not include any transportation charges or costs of installation or any liability for direct, indirect, or not be
compromised or circumvented; that the product will prevent any persona; injury or property loss by intruder, robbery, fire or
otherwise; or that the product will in all cases provide adequate warning or protection. Buyer understands that a properly
installed and maintained alarm may only reduce the risk of intruder, robbery or fire without warning, but is not insurance or a
guaranty that such will not occur or that there will be no personal injury or property loss as a result. Consequently seller shall
have no liability for any personal injury, property damage or loss based on a claim that the product fails to give warning.
However, if seller is held liable, whether directly or indirectly, for any loss or damage arising from under this limited warranty
or otherwise, regardless of cause or origin, sellers maximum liability shall not exceed the purchase price of the product, which
shall be complete and exclusive remedy against seller. No employee or representative of Seller is authorized to change this
warranty in any way or grant any other warranty.
WARNING: This product should be tested at least once a week.
Contacting RISCO Group
RISCO Group is committed to customer service and product support. You can contact us through our website
(www.riscogroup.com) or at the following telephone and fax numbers:
nited Kingdom
el: +44-161-655-5500
echnical@riscogroup.co.uk
taly
el: +39-02-66590054
ort@riscogroup.it
Spain
el: +34-91-490-2133
ort-es@riscogroup.com
rance
el: +33-164-73-28-50
ort-fr@riscogroup.com
elgium
el: +32-2522-7622
ort-be@riscogroup.com
SA
el: +1-631-719-4400
ort-usa@riscogroup.com
razil
el: +1-866-969-5111
ort-br@riscogroup.com
hina
el: +86-21-52-39-0066
ort-cn@riscogroup.com
oland
el: +48-22-500-28-40
ort-pl@riscogroup.com
srael
el: +972-3-963-7777
ort@riscogroup.com
All rights reserved.
No part of this document may be reproduced in any form without prior written permission from the publisher.
© RISCO Group 02/2013 5IN2021
Page 2
Loading...