Renault Captur (2023) Owner’s Manual

CAPTUR

vehicle user manual

Castrol,
exclusive
Renault
partner

Benefit from cutting-edge technology born out of competition to ensure the performance and longevity of your Renault
thanks to wide range of engine lubricants developed specially by Renault and Castrol.

renault.frRenault recommends

Welcome to your new vehicle

This driver’s handbook contains the information necessary:
– for you to familiarise yourself with your vehicle, to use it to its best advantage and to benefit fully from the all the functions and

the technical developments it incorporates.

– to ensure that it always gives the best performance by following the simple, but comprehensive advice concerning regular main-

tenance.
– to enable you to deal quickly with minor faults not requiring specialist attention.
It is well worth taking a few minutes to read this handbook to familiarise yourself with the information and guidelines it contains
about the vehicle and its functions and new features. If certain points are still unclear, our Network technicians will be only too
pleased to provide you with any additional information.

To help you, you will find the following symbols:

 and  These appear in the vehicle and indicate that you should consult the manual for detailed information and/or

limits on operations with respect to your vehicle’s equipment.

➥ anywhere in the manual indicates a transfer to a page.

anywhere in the manual indicates a hazard, danger or a safety recommendation.

The descriptions of the models given in this handbook are based on the technical specifications at the time of writing. This hand­book covers all items of equipment (both standard and optional) available for these models but whether or not these are
fitted to the vehicle depends on the version, options selected and the country where the vehicle is sold.
This handbook may also contain information about items of equipment to be introduced later in the model year.
The diagrams in the user manual are provided as examples.

Enjoy driving your new vehicle.

Translated from French. Copying or translation, in part or in full, is forbidden unless prior written permission has been obtained from the car manufacturer.

0.1

EXTERIOR

Electric windows ➥ 3.20
Wiper ➥ 1.101 and ➥ 1.106
Demisting ➥ 3.5 and ➥ 3.11

Rear view mirrors ➥ 1.90

Key/Remote control ➥ 1.2
Map ➥ 1.6
Locking/unlocking the doors

➥ 1.16

Lights: operation ➥ 1.93
Lights: replacement ➥ 5.15

0.2

Bodywork maintenance ➥ 4.16

Tyres ➥ 5.12

L Filling up with fuel/LPG ➥ 1.108

PASSENGER COMPARTMENT

Adjusting your driving po­sition ➥ 1.23

Front seats ➥ 1.21
Front headrests ➥ 1.92

Passenger compartment storage/fit­tings ➥ 3.29

Rear bench seat ➥ 3.35
Rear headrests ➥ 3.34

Child safety ➥ 1.37

Luggage compartment stor­age/fittings ➥ 3.39

0.3

DRIVER’S POSITION

Instrument panel ➥ 1.58

Exterior lighting ➥ 1.93

Cruise control ➥ 2.98
Stop and Go adaptive cruise

control ➥ 2.103
Speed limiter ➥ 2.94

GPL Command ➥ 4.2

Bonnet release ➥ 4.2

Steering wheel adjust­ment ➥ 1.88

Key ignition switch ➥ 2.4

Trip computer controls
➥ 1.71

Multimedia screen
➥ 3.17

Heated seat(s) ➥ 1.21

Heating/Air conditioning
system ➥ 3.5

Gearstick ➥ 2.24

Telephone charging zone
➥ 3.29

Parking brake ➥ 2.25

Engine start/stop button
➥ 2.6

0.4

DRIVING AIDS

ABS (anti-lock braking system)
ESC (electronic stability control)
Braking assistance
Hill start assistance
➥ 2.46

AUTOHOLD ➥ 2.29

Lane departure warning ➥ 2.51

Lane Keeping Assist ➥ 2.56

Active emergency braking ➥ 2.82

Blind spot warning ➥ 2.62

Stop and Start ➥ 2.12

Safe distance alert ➥ 2.69

Speed limiter ➥ 2.94

Detection of road signs ➥ 2.90

Cruise control ➥ 2.98
Stop and Go adaptive cruise con-

trol ➥ 2.103

Parking distance control ➥ 2.116

Reversing camera ➥ 2.123

360° camera ➥ 2.73

Parking exit warning ➥ 2.125

Assisted parking ➥ 2.129

Tyre pressure loss warning
➥ 2.40

0.5

SAFETY ON BOARD

Front Airbags ➥ 1.28

Side Airbags ➥ 1.35

Inhibiting the front pas­senger airbag ➥ 1.51

Curtain Airbags ➥ 1.35

0.6

Seat belts ➥ 1.23

IDENTIFYING A VEHICLE - LABELS

Vehicle identification
plate ➥ 6.2

Technical Information for the
emergency services ➥ 6.3

Engine identification ➥ 6.4

Review of a vehicle identification
number ➥ 6.2

Tyre pressure labels ➥ 2.40
➥ 4.11

0.7

THE ENGINE COMPARTMENT (routine maintenance)

Opening the bonnet
➥ 4.2

Coolant level ➥ 4.8

Engine oil filler cap ➥ 4.5
Engine oil dipstick ➥ 4.4

Windscreen washer fluid
➥ 4.8

0.8

Brake fluid ➥ 4.8

Battery ➥ 4.13

BREAKDOWN RECOVERY

Replacing windscreen wiper
blade(s) ➥ 1.101

Front towing point ➥ 5.36

Replacing the rear screen
wiper blade ➥ 1.106

Replacement of the direc­tion indicator lights ➥ 5.16

Rear towing point ➥ 5.36

Puncture:
Tools ➥ 5.7
Emergency spare

wheel ➥ 5.2
Changing a wheel

➥ 5.10

Fuses ➥ 5.31

0.9

0.10

CONTENTS

Sections

Getting to know your vehicle ...............................

Driving ...................................................................

Your comfort .........................................................

Maintenance .........................................................

Practical advice ....................................................

Technical specifications ......................................

Alphabetical index ...............................................

1

2

3

4

5

6

7

0.11

0.12

Section 1: Getting to know your Vehicle

Key, radio frequency remote control: general information, use, deadlocking .................. 1.2

Card: general information, use, deadlocking ........................................... 1.6

Opening and closing the doors ..................................................... 1.14

Locking, unlocking the opening elements ............................................. 1.16

Automatic locking when driving ..................................................... 1.20

Seat belts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.23

Additional methods of restraint ..................................................... 1.28

in addition to the front seat belts .............................................. 1.28

to the rear seat belts ....................................................... 1.34

side ..................................................................... 1.35

Child safety: general information .................................................... 1.37

choosing a child seat mounting ............................................... 1.40

Fitting a child seat, general information ......................................... 1.43

Child seats: attachment by seat belt or by isofix system .................................. 1.45

Deactivating, activating the front passenger airbag ................................ 1.51

Driving position ................................................................. 1.54

Instrument panel ................................................................ 1.58

Displays and indicators ..................................................... 1.64

Trip computer ............................................................. 1.71

Vehicle settings personalisation menu .......................................... 1.83

Clock and outdoor temperature ..................................................... 1.86

Steering wheel, Power-assisted steering ............................................. 1.88

Rear view mirrors ............................................................... 1.90

Headrests - Seats ............................................................... 1.92

Exterior lighting and signals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.93

Audible and visual signals ......................................................... 1.99

Headlight beam adjustment ........................................................ 1.100

Washers, wipers ................................................................ 1.101

Fuel tank (filling with fuel) ......................................................... 1.108

Reagent tank ................................................................... 1.113

1.1

KEY, RADIO FREQUENCY REMOTE CONTROL: general information (1/2)

3

2

3

1

2

4

1

5

5

1 Locks all the opening elements.
2 Unlocks all the opening elements.
3 Driver’s door and ignition key.
5 Locking/unlocking the boot only.

Remote control with switchblade
key:

4 Locking/unlocking using the switch-

blade key. To release the insert from
its housing, press button 4, it comes
out automatically. Press button 4 and
guide the insert back into its housing.

Advice

Avoid leaving the remote control in
hot, cold or humid areas.

The key must not be used for any
function other than those described
in the handbook (removing the cap
from a bottle, etc.).

Driver’s responsibility
when parking or stopping
the vehicle

Never leave an animal,
child or adult who is not self-suffi­cient alone on your vehicle, even for
a short time.

They may pose a risk to themselves
or to others by starting the engine,
activating equipment such as the
electric windows or locking the
doors.

Also, in hot and/or sunny weather,
please remember that the tempera­ture inside the passenger compart­ment increases very quickly.

RISK OF DEATH OR SERIOUS
INJURY.

1.2

KEY, RADIO FREQUENCY REMOTE CONTROL: general information (2/2)

Radio frequency remote
control operating range

This varies according to the surround­ings: take care not to lock or unlock the
doors by inadvertently pressing the but­tons on the remote control.

Note: if a door or the boot is open or not
properly shut, locking is not carried out.
A beep sounds and the hazard warning
lights and side repeaters do not flash.

Interference

Interference by factors in the immediate
vicinity (external installations or the use
of equipment operating on the same
frequency as the remote control) may
affect the operation of the remote con­trol.

Replacement and additional keys
or remote controls.

You must only contact an approved
dealer:

– If you need to replace a key it will

be necessary to take the vehicle
and all of its keys to an approved
Dealer in order to initialise the
system.

– Depending on the vehicle, you

have the option of using up to
four remote controls.

Remote control unit failure

Make sure that the correct battery
type is being used, and that the
battery is in good condition and in­serted correctly. These batteries
have a service life of approximately
two years.

How to change the battery ➥ 5.22.

1.3

RADIO FREQUENCY REMOTE CONTROL: use

The remote control A can be used to
lock or unlock the doors and boot. It is
powered by a battery which can be re­placed. ➥ 5.22.

Locking the doors

Press locking button 1.
The hazard lights and side repeaters
flash twice to indicate that the doors
have locked and, on some vehicles,
the door mirrors fold in automatically.
Pressing the 1 button twice locks the
vehicle and enables the closure of the
front, rear windows and sunroof (de­pending on the vehicle).
Note: if a door or the boot is open or not
properly shut, locking is not carried out.
A beep sounds and the hazard warning
lights and side repeaters do not flash.

Depending on the vehicle, the door
mirrors fold in/out automatically
when the vehicle is locked/unlocked
➥ 1.90

A

2

1

2

1

Unlocking the doors

Pressing button 2 unlocks the doors
and tailgate.

The hazard lights and side repeaters
flash once to indicate that the doors
have unlocked and, on some vehicles,
the door mirrors fold out automatically.

Note: with the ignition on and the
engine running ➥ 2.3, buttons on the
remote control are not activated.

3

3

Locking/unlocking only the
boot

Press the button 3 to lock/unlock the
boot only.

Driver’s responsibility when parking or stopping the vehicle

Never leave an animal, child or adult who is not self-sufficient alone on
your vehicle, even for a short time.

activating equipment such as the electric windows or locking the doors.
Also, in hot and/or sunny weather, please remember that the temperature inside
the passenger compartment increases very quickly.

RISK OF DEATH OR SERIOUS INJURY.

They may pose a risk to themselves or to others by starting the engine,

1.4

RADIO FREQUENCY REMOTE CONTROL UNIT: deadlocking

If the vehicle is equipped with a dead­locking function, this allows you to lock
the opening elements and to prevent
the doors from being unlocked using
the interior handles (for example, by
breaking the window and then trying to

1

1

open the door from the inside).
To do this, press button 1 twice in quick

succession.
The hazard warning lights and side in-

dicator lights give two slow flashes and
three quick flashes to indicate locking.

Depending on the vehicle, the door mir­rors fold in automatically when the vehi­cle is locked ➥ 1.90.

Never use deadlocking if
someone is still inside the
vehicle.

1.5

CARD: general information (1/3)

1

4

2

3

Battery life

Make sure that the correct battery type

1

5

2

is being used, and that the battery is in
good condition and inserted correctly.
Its service life is approximately two
years: it should be replaced when the
message “Keycard Battery Low” ap­pears on the instrument panel ➥ 5.24.

3

Remote engine start-up

(depending on vehicle)
Press button 5 to activate the remote

engine start-up. ➥ 2.6.

1 Unlocking the doors and tailgate.
2 Locking all doors and tailgate.
3 Locking/unlocking the boot only.
4 Switching-on the lighting remotely,

or, depending on the vehicle,
5 Remote engine start-up.

1.6

The card is used for:

– locking/unlocking the doors and tail-

gate (doors, tailgate) and the fuel
filler flap (see the following pages);

– switching on the vehicle lighting re-

motely (refer to the following pages);

– automatic remote closing of the elec-

tric windows ➥ 3.20;

– starting the engine ➥ 2.6.

When the battery is flat, you can still
lock/unlock and start your vehicle.
➥ 1.16, ➥ 2.6.

card operating range

This varies according to the environ­ment: take care not to accidentally lock
or unlock the vehicle by inadvertently
pressing the buttons on the card.

Note: if a door or the boot is open or not
properly shut, locking is not carried out.
A beep sounds and the hazard warning
lights and side repeaters do not flash.

CARD: general information (2/3)

4

Distance lighting function

Pressing button 4 switches on the
dipped beam headlights and the exte­rior lighting for approximately 20 sec­onds. This can be used, for example,
to identify the vehicle from a distance
when parked in a car park.

Pressing and holding the 4 button for
approximately two seconds activates
the exterior lighting and a sound is
emitted.

Note: pressing button 4 again switches
off the lighting.

Advice

Avoid leaving the card in hot, cold or
humid areas.

Do not keep the card in a place
where it could be bent or dam­aged accidentally, such as in a back
pocket of a garment.

Replacement: need for an
additional card

If you lose your card or require an­other, you can obtain one from an
authorised dealer.

If a card is replaced, it will be neces­sary to take the vehicle and all its
cards to an approved Dealer to ini­tialise the system.

You may use up to four cards per
vehicle.

Interference

Interference by factors in the immediate
vicinity (external installations or the use
of equipment operating on the same
frequency as the card) may disrupt its
operation.

Driver’s responsibility

when parking or stopping

the vehicle

Never leave an animal,
child or adult who is not self-suffi­cient alone in your vehicle, even for
a short time.

They may pose a risk to themselves
or to others by starting the engine,
activating equipment such as the
electric windows or locking the
doors, for example.

Also, in hot and/or sunny weather,
please remember that the tempera­ture inside the passenger compart­ment increases very quickly.

RISK OF DEATH OR SERIOUS
INJURY.

1.7

CARD: general information (3/3)

5

A

6

7

8

Fitting a strap 7

Slide the rear casing 5 downwards
while pressing on zone A.

1.8

Insert the strap into the 8 component
and pass the end of the strap through
the buckle.

Position the strap at the 6 opening and
close the cartridge.

Note: check that the diameter of the 7
strap cord fits the 6 opening.

“HANDS-FREE” CARD: use (1/4)

Deactivating/activating the
«hands-free» mode

Depending on the vehicle, you can de-

1

2

Depending on the vehicle, there are two
to three ways to unlock/lock the vehicle:

– “hands-free”, when approaching and

moving away from the vehicle;

– “hands-free”, using the 2 button on

the 1 handle of one of the front doors;

– using the card in remote control

mode.

activate/activate:
– unlocking when approaching and

– locking and unlocking by pressing on

You can also disable/activate the sound
signal that is emitted upon locking when
moving away from the vehicle ➥ 1.83.

locking when moving away from the
vehicle;

the buttons on the door handle.

Never leave your vehicle

with the card inside.

Driver’s responsibility

when parking or stopping

the vehicle

Never leave an animal,
child or adult who is not self-suffi­cient alone in your vehicle, even for
a short time.

They may pose a risk to themselves
or to others by starting the engine,
activating equipment such as the
electric windows or locking the
doors, for example.

Also, in hot and/or sunny weather,
please remember that the tempera­ture inside the passenger compart­ment increases very quickly.

RISK OF DEATH OR SERIOUS
INJURY.

Do not store the card anywhere it
may come into contact with other
electronic equipment (computer,
phone etc.) as this could hinder its
operation.

1.9

“HANDS-FREE” CARD: use (2/4)

3

Hands-free unlocking, when
approaching the vehicle;

With the card in access zone 3, the ve­hicle will unlock. Unlocking is indicated
by one flash of the hazard warning
lights and the indicator lights.

Depending on the vehicle, the door
mirrors fold in/out automatically
when the vehicle is locked/unlocked
➥ 1.90.

4

Hands-free locking when
moving away from the
vehicle

With the card on you, doors and lug­gage compartment door closed, move
away from the vehicle: it will lock auto­matically once you have left the access
zone 3.

Note: the distance at which the vehicle
locks depends on the surroundings.

To indicate that the vehicle has been
locked, the hazard warning lights
flash twice and then light up for ap­proximately four seconds, and a beep
sounds in confirmation.

5

If the card has been within the detec­tion area 3 for approximately 15 min­utes, remote locking is disabled. To lock
the vehicle, press the 5 button on the
card or, depending on the vehicle, the 2
button on the handle 1.

The vehicle cannot be remotely locked
if the card is within the area 4.

1.10

“HANDS-FREE” CARD: use (3/4)

The hazard warning lights flash twice
to indicate that the vehicle is locked
and, depending on the vehicle, the door
mirrors automatically fold in.

1

2

“Hands-free” unlocking/
locking using button 2

(depending on the vehicle)
With the card in zone 3 and the vehi-

cle locked, press the button 2 on the
handle 1 of one of the two front doors:
the vehicle unlocks. Press the button 2
also unlocks all the doors and the tail­gate.
The hazard lights and side repeaters
flash once to indicate that the doors
have unlocked and, on some vehicles,
the door mirrors fold out automatically.
Pressing the 2 button again locks the
vehicle.

Special features of the
unlocking system

Under certain circumstances, approach
unlocking is deactivated:

– after eight days of no use of the vehi-

cle;

– if the card remains close to the 3

area of the vehicle for approximately
five minutes after the vehicle has
been locked;

– after several passes in the vicinity of

the 3 area of the vehicle and without
the door being unlocked.

Use the remote control card or, depend­ing on the vehicle, press the 2 button on
the door handle 1 to unlock the vehicle
and reactivate hands-free mode.

4

Special features relating to
“hands-free” locking

After locking in “hands-free” mode, you
have to wait approximately three sec­onds to be able to unlock the vehicle
again. During these three seconds, the
door handles can be tried to make sure
that the vehicle is locked properly.

Note: if a door or the boot is open or not
properly shut, locking is not carried out.
A beep sounds and the hazard warning
lights and side repeaters do not flash.

1.11

“HANDS-FREE” CARD: use (4/4)

Locking using the card

With the doors and boot closed, press

7

5

6

Using the card as a remote
control

Unlocking with the card

Press button 7.
The hazard lights and side repeaters
flash once to indicate that the doors
have unlocked and, on some vehicles,
the door mirrors fold out automatically.

button 5: the vehicle locks.
The hazard warning lights flash twice

to indicate that the vehicle is locked
and, depending on the vehicle, the door
mirrors automatically fold in.

Pressing the 5 button twice locks the
vehicle and enables the closure of the
front and rear windows (depending on
the vehicle).

Note:

– the maximum distance at which the

– if a door or the boot is open or not

vehicle locks depends on the sur­roundings;

properly shut, locking is not carried
out. A beep sounds and the hazard
warning lights and side repeaters do
not flash.

4

If, while the engine is running, a door
is opened and closed, and the card is
no longer in the zone 4, the message
“Keycard Not Detected” indicates that
the card is not inside the vehicle. This
will, for example, prevent you from driv­ing away after dropping off a passenger
who has kept the card on them.

The warning disappears when the card
is detected again.

The card buttons are deactivated
when the engine is running.

1.12

Locking/unlocking only the
boot

Press the button 6 to lock/unlock the
boot only.

“HANDS-FREE” CARD: DEADLOCKING

If the vehicle is equipped with a dead-

1

locking function, this allows you to lock
the opening elements and to prevent
the doors from being unlocked using
the interior handles (for example, by
breaking the window and then trying to
open the door from the inside).

To do this, press button 1 twice in quick
succession.

Locking is confirmed by two slow
flashes and three quick flashes of
the hazard warning lights and indicator
lights.

Special note: deadlocking is not pos­sible if the hazard warning lights or the
side lights are lit.

Never use deadlocking if
someone is still inside the
vehicle.

Depending on the vehicle, the door
mirrors fold in automatically when
the vehicle is locked ➥ 1.90.

1.13

OPENING AND CLOSING THE DOORS (1/2)

3

1

Opening the doors from the
outside

Front doors

With the doors unlocked or the card on
you, hold the 1 handle and pull towards
you.

2

Rear doors

With the doors unlocked or the card on
you, hold the 2 handle and pull towards
you.

Opening from the inside

Pull handle 3.
Depending on the vehicle, it may be

necessary to pull handle 3 twice: the
first time to unlock the door, the second
time to open it.

As a safety precaution,

the doors should only be

opened or closed when the

vehicle is stationary.

1.14

OPENING AND CLOSING THE DOORS (2/2)

Lights-on reminder buzzer

If you have switched off the ignition
and left the lights switched on, a re­minder buzzer will sound when a door
is opened.

Door/tailgate open buzzer

When the vehicle is stationary, the 2

warning light appears on the instrument
panel accompanied by a warning light
indicating which of the opening ele­ments (door(s), luggage compartment)
are open or incorrectly closed.

Once the vehicle reaches a speed
of approximately 6 mph (10 km/h), a
warning light indicates if the door(s) or
luggage compartment are open or not
properly closed, along with the mes­sage “Tailgate open” or “WARNING:
Door Open” and a beep will sound for
around 40 seconds or until the door/
luggage compartment is closed.

4

Child safety

Move lever 4 and check from the inside
that the doors are securely locked, to
prevent the rear doors being opened
from the inside.

Driver’s responsibility

when parking or stopping

the vehicle

Never leave an animal,
child or adult who is not self-suffi­cient alone on your vehicle, even for
a short time.
They may pose a risk to themselves
or to others by starting the engine,
activating equipment such as the
electric windows or locking the
doors.
Also, in hot and/or sunny weather,
please remember that the tempera­ture inside the passenger compart­ment increases very quickly.

RISK OF DEATH OR SERIOUS
INJURY.

1.15

LOCKING, UNLOCKING THE DOORS (1/4)

If the remote control or,
depending on the vehicle, the
card does not work

In some cases, the radio frequency

remote control or the card may not
work:
– card or radio frequency remote con-

trol battery worn or run flat, vehicle
battery flat etc;

– use of appliances operating on the

same frequency as the card (mobile
phone, etc.);

– vehicle located in a high electromag-

netic radiation zone.

It is then possible:
– to use the radio frequency remote

control or the emergency key inte­grated in the card (depending on the
vehicle) to unlock the driver’s door;

– to use the interior door locking/un-

locking control (refer to the following
pages).

The card’s built-in key

The 2 integrated key can be used to
lock or unlock the driver’s door when
the card is not working.

Access with key 2

Slide the rear casing 1 downwards
while pressing on zone A.

1

2

A

1.16

LOCKING, UNLOCKING THE DOORS (2/4)

3

B

4

2

Using the key integrated in
the card

– Pull handle 3;
– press the cover B on the driver’s

door down;

– insert the end of the key 2 in the

notch 4 at the bottom of the cover B;

– rotate it upwards to remove the

cover B;

– insert the key 2 into the lock of the

driver’s door, lock or unlock.

Once you are inside the vehicle, put the
key back in its casing in the card.

B

3

4

5

Vehicles with key/remote
control

Using the key

– Pull handle 3;
– press the cover B on the driver’s

door down;

– insert the end of the key 5 in the

notch 4 at the bottom of the cover B;

– rotate it upwards to remove the

cover B;

– insert the key 5 into the lock of the

driver’s door, lock or unlock.

1.17

LOCKING, UNLOCKING THE DOORS (3/4)

6

5

Locking the doors manually

Turn screw 5 with the door open (using
the end of the key) and close the door.

This means that the doors are then
locked from the outside.

The doors may then only be opened
from the inside or by using the key in
the driver’s door.

1.18

Interior locking/unlocking
door control

Switch 6 controls the doors, the boot
and the fuel filler flap simultaneously.

If a door or the tailgate is open or not
closed properly, the doors and tailgate
lock/unlock quickly.

If transporting an object with the tail­gate open, you can still lock the doors:
with the engine stopped, press and
hold switch 6 to lock the other doors.

LOCKING, UNLOCKING THE DOORS (4/4)

Door and tailgate status
indicator

When the ignition is on, the 6 switch

warning light indicates the locking
status of the opening elements:

– indicator light on, the doors and tail-

gate are locked;

– indicator light off, the doors and tail-

gate are unlocked.

When you lock the doors, the indicator
light remains lit and then goes out.

Driver’s responsibility

If you decide to keep the
doors locked when you are

driving, remember that it
may be more difficult for those as­sisting you to gain access to the
passenger compartment in the
event of an emergency.

Locking the opening
elements without the card or
the key

For example, in the event of a dis­charged battery or the card or key tem­porarily not working etc.

With the engine switched off and a
door or tailgate open, press and hold

the 6 switch for more than five seconds.
When the door is closed, all the doors

and the tailgate will be locked.
Note: unlocking the vehicle from the

outside is only possible with the card in
the vehicle’s access zone or using the
key.

Never leave your vehicle
with the key or card inside.

1.19

AUTOMATIC LOCKING WHEN DRIVING

1

Operating principle

After the vehicle is started, the system
automatically locks the doors when you
are driving at approximately 6 mph (10
km/h) and over.

The door can be unlocked:
– by pressing the central door unlock-

ing switch 1;

– at a standstill, by opening a front

door from inside the vehicle.

NB: if a door is opened or closed, it
will automatically lock again when the
vehicle reaches a speed of 6 mph (10
km/h).

Activating/deactivating the
function

To activate: with the vehicle station-

ary and the engine running, press the 1
switch until a beep sounds.

To deactivate: with the vehicle station­ary and the engine running, press the
switch 1 until you hear two beeps.

The function can also be activated and
deactivated via the multimedia screen
(depending on the vehicle). ➥ 1.83.

Operating faults

If you experience an operating fault
(no central locking, the indicator light 1
does not light up when trying to lock the
doors and luggage compartment etc.),
make sure that central locking has not
been deactivated by mistake and check
that the doors and luggage compart­ment are properly closed. If they are
properly closed, contact an approved
dealer.

Driver’s responsibility

If you decide to keep the
doors locked when you are

driving, remember that it
may be more difficult for those as­sisting you to gain access to the
passenger compartment in the
event of an emergency.

1.20

FRONT SEATS (1/2)

5

4

2

1

Adjusting the seat position

To move the seat forwards or back

Move the 1 switch forwards or back­wards or, depending on the vehicle,
lift and hold the 3 handle to unlock the
seat. Release the handle once the seat
is in the correct position and ensure
that the seat is locked.

To raise or lower the seat base

Move the 1 switch up or down or, de­pending on the vehicle, move the 4
lever as many times as necessary up­wards or downwards to the desired po­sition.

3

Adjusting the seatback

To tilt the seatback

Activate the 2 switch forwards or back­wards, or depending on the vehicle, lift
the 5 handle and tilt the seatback to the
desired position. Release the handle at
the desired position and make sure that
it is locked.

After making adjustments,

make sure that the seat-

backs are correctly locked

in place.

For safety reasons, carry

out any adjustments

when the vehicle is not

being driven.

We would advise you not to recline
the seatbacks too far to ensure that
the effectiveness of the seat belts is
not reduced.

Nothing should be placed on the
floor (area in front of driver) as such
objects may slide under the pedal
during braking manoeuvres, thus
obstructing its use.

1.21

FRONT SEATS (2/2)

6

Central armrest 6

(depending on the vehicle)
To adjust the position of the central arm-

rest 6, slide it forwards or backwards.

To adjust the seat’s lumbar
position

Lower handle 7 to increase the support
and lift it to decrease it.

1.22

7

Heated seats

With the ignition on:
– Pressing the switch 8 on the required

seat for the first time activates the
heating system on high. Both inte­grated switch warning lights come
on;

– pressing the switch for the second

time changes the heating to low. One
integrated warning light comes on;

– pressing for the third time turns the

heating off.

8

Operating faults

When an operating fault is detected,
the warning light of the 8 switch for the
seat concerned switches-off after ap­proximately five seconds.

Consult an approved dealer.

SEAT BELTS (1/5)

Always wear your seat belt when trav­elling in your vehicle. You must also
comply with the legislation of the par­ticular country you are in.

Before starting, first adjust your driv­ing position, then ask all occupants
to adjust their seat belts to ensure
optimum protection.

Adjusting your driving
position

– Sit well back in your seat (having

first removed your coat or jacket).
This is essential to ensure your back
is positioned correctly;

– adjust the distance between the

seat and the pedals. Your seat

should be as far back as possible
while still allowing you to depress
the clutch pedal fully. The seatback
should be adjusted so that your arms
are slightly bent when you hold the
steering wheel;

– adjust the position of your head-

rest. For maximum safety, your head

must be as close as possible to the
headrest;

– adjust the height of the seat. This

adjustment allows you to select the
seat position which offers you the
best possible view;

– adjust the position of the steering

wheel.

Make sure that the rear bench seat
is locked in position correctly so that
the rear seat belts will operate cor­rectly. ➥ 3.35.

Incorrectly adjusted or

twisted seat belts may

cause injuries in the event

of an accident.
Use one seat belt per person,

whether child or adult.
Even pregnant women should wear

a seat belt. In this case, ensure that
the lap belt is not exerting too much
pressure on the abdomen, but do
not allow any slack.

1.23

SEAT BELTS (2/5)

1

5

2

Locking

Unwind the belt slowly and smoothly
and ensure that buckle 3 locks into
catch 5 (check that it is locked by pull­ing on buckle 3).

If the belt jams, allow it to return slightly
before attempting to unwind it again.

If your seat belt is completely jammed,
pull slowly, but firmly, so that just over

3

4

5

3 cm unwinds. Allow it to return slightly
before attempting to unwind it again.

If there is still a problem, contact an ap­proved dealer.

Adjusting the seat belts

Sit with your back firmly against the
seatback.

Shoulder strap 1 should be as close as
possible to the base of the neck but not
on it.

Lap belt 2 should be worn flat over the
thighs and against the pelvis.

The belt should be worn so that it is
as close as possible to your body, i.e.:
avoid wearing heavy clothing or keep­ing bulky objects under the belts, etc.

1.24

Unlocking

Press button 4 and the seat belt will be
rewound by the inertia reel. Guide the
belt.

SEAT BELTS (3/5)

ß

cle, front passenger seat belt re­minder

This appears on the central display
when the ignition is switched on and
if the driver’s and/or front passenger’s
seat belt(s) (if the passenger seat is
occupied) is not fastened. Depending
on the vehicle, if the seat is occupied
and one of these seat belts is not fas­tened or becomes unfastened while
the vehicle is moving at a speed over
approximately 12 mph (20 km/h), the

Driver’s seat belt reminder
and, depending on the vehi-

™ warning light flashes and a beep

sounds for approximately 120 seconds.
Note: an object placed on the passen-

ger seat may activate the warning light
in some cases, depending on the ve­hicle.

Rear seat belt reminder (depending
on the vehicle)

The 6 graphic is displayed on the in­strument panel when the ignition is
switched on. This informs the driver of
the fastening status of each of the rear
seat belts every time:
– the ignition is switched on;
– a door is opened;
– fastening or unfastening of a rear

seat belt.

6

playback of 6 graphic:
– indicator green: seatbelt fastened;
– indicator in red: the seat is occupied

and the seat belt is not fastened;

– indicator grey: seat not occupied.

Depending on the vehicle, the
warning light on the central display also
appears when the ignition is switched
on, if a rear seat is occupied and the
seat belt is not fastened.
When the vehicle speed is less than
approximately 12 mph (20 km/h), the

™

™ warning light on the central dis-

play appears if a rear seat belt is un­fastened.

It is accompanied by the 6 symbol which
appears for approximately 60 seconds
each time one of the rear seat belts is
fastened or unfastened.

When the vehicle speed reaches or ex­ceeds 12 mph (20 km/h), if one of the
rear seat belts is or becomes unfas­tened during the journey:

– the

™ warning light flashes on

the central display;
and
– a beep is emitted for 30 to 120 sec-

onds (depending on the version);
and
– the 6 symbol is displayed for at least

approximately 60 seconds and

the symbol for the seat concerned

changes to red.
Always make sure that the rear pas-

sengers are properly fastened and that
the number of fastened seat belts in­dicated corresponds to the number of
rear seats occupied.

Note: in some cases the warning light
may be activated if an object is placed
on one of the rear seats, depending on
the vehicle.

1.25

SEAT BELTS (4/5)

7

Adjusting the height of the
front seat belts

Use button 7 to adjust the seat belt
height so that the shoulder strap is worn
as shown previously. Press the button 7
and raise or lower the seat belt. Make
sure that the seat belt is locked in posi­tion correctly after you have adjusted it.

9

8

10

11

Rear side seat belts 8

The belts are locked, unlocked and
adjusted in the same way as the front
belts.

Check that the rear seat
belts are positioned and
operating correctly each
time the rear bench seat is

moved.

9

10

12

11

13

Rear centre seat belt

Slowly unwind belt 9.
Click buckle 10 into black catch 11.
Fasten the tongue 12 in the red

buckle 13.

Ensure that you always leave the
tongue 10 fastened in the buckle 11
even if no passenger is present in
the centre seat.

1.26

SEAT BELTS (5/5)

The following information applies to the vehicle’s front and rear seat belts.

– No modification may be made to the component parts of the originally fitted restraint system: seat belts, seats and

their mountings. For special operations (e.g. fitting child seats), contact an authorised dealer.

– Do not use devices which allow any slack in the belts (e.g. clothes pegs, clips, etc.): a seat belt which is worn too

loosely may cause injury in the event of an accident.
– Never wear the shoulder strap under your arm or behind your back.
– Never use the same belt for more than one person and never hold a baby or child on your lap with your seat belt around

them.
– The belt should never be twisted.
– Following an accident, have the seat belts checked and replaced if necessary. Always replace your seat belts as soon as

they show any signs of wear.
– When the rear bench seat is being put back, make sure that the seat belts and buckles are correctly positioned so that they

can be used properly.
– Make sure that the buckle is inserted into the appropriate catch.
– Ensure that no objects are placed in the area around the seat belt catch as they could prevent it from being properly secured.
– Make sure the seat belt catch is properly positioned (it should not be hidden away, crushed or flattened by people or ob-

jects).

1.27

METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (1/6)

Depending on the vehicle, they will con­sist of:

– seat belt inertia reel pretension-

ers;

– central seat belt pretensioners;

– chest-level load limiters;
– airbags driver and passenger

front.

These systems are designed to act in­dependently or together when the vehi­cle is subjected to a frontal impact.

Depending on the severity of the
impact, the system can trigger:

– seat belt locking;
– the seat belt inertia reel pretensioner

(which engages to correct seat belt
slack);

– lap seat belt pretensioners to hold

the occupant in their seat;

– the front airbag.

2

1

Pretensioners

The pretensioners hold the seat belt
against the body, holding the occupant
more securely against the seat, thus in­creasing the seat belt’s efficiency.

In the event of a severe frontal impact
and if the ignition is switched on, the
system may engage the following de­pending on the force of the impact:

– the seat belt inertia reel preten-

sioner 1 which instantly retracts the
seat belt;

– the lap seat belt inertia reel preten-

sioner 2 on the front seats.

– Have the entire restraint

system checked following
an accident.

– No operation whatso­ever is permitted on any part
of the system (pretensioners,
airbags, computers, wiring) and
the system components must not
be reused on any other vehicle,
even if identical.

– Only qualified personnel from our

Network may work on the airbags;
otherwise the system may trigger
accidentally and cause injury.

– The electric trigger system may

only be tested by a specially
trained technician using special
equipment.

– When the vehicle is scrapped,

contact an approved dealer for
disposal of the pretensioner and
airbags gas generators.

1.28

METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (2/6)

Load limiter

Above a certain severity of impact, this
mechanism is used to limit the force of
the belt against the body so that it is at
an acceptable level.

driver and passenger front
Airbags

Fitted to the driver and passenger
sides.

A symbol on the lower section of the
windscreen indicates if this equipment
is present (depending on the vehicle).

Each airbag system consists of:
– an airbag and gas generator fitted on

the steering wheel for the driver and
in the dashboard for the passenger;

– an electronic unit for system monitor-

ing which controls the gas generator
electrical trigger system;

– remote sensors;

– a single warning light

instrument panel.

å on the

The airbag system uses py-

rotechnic principles. This

explains why, when the

airbag inflates, it will gener-

ate heat, produce smoke (this does
not mean that a fire is about to start)
and make a banging noise. In a situ­ation where an airbag is required, it
will inflate immediately and this may
cause some minor, superficial graz­ing to the skin or other problems.

1.29

METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (3/6)

Operating faults

å This warning light comes on

when the engine is started and then
goes out after approximately three sec­onds.

If it does not come on when the ignition
is switched on or if it stays on, there is a
fault in the system.

Contact your approved Dealer as soon
as possible.

Your protection will be reduced until this
fault is rectified.

Operation

This system is only operational when
the ignition is switched on.

In a severe frontal impact, the airbags
inflate rapidly, cushioning the impact
of the driver's head and chest against
the steering wheel and of the front pas­senger against the dashboard. The air
bags then deflate immediately so that
the passengers are not in any way hin­dered from leaving the vehicle.

1.30

METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (4/6)

The following conditions will trigger
the pretensioners or airbags.

In a frontal impact against a rigid

(non-deformable) surface at an impact
speed equal to or greater than 16 mph

(25 km/h).

In a frontal impact with another vehi-

cle of an equivalent or higher category,
with an impact area equal to or greater
than 40%, where the speed of both ve­hicles is equal to or greater than 25 mph

(40 km/h).

In a side impact with another vehicle

of an equivalent or higher category, at
an impact speed equal to or greater
than 31 mph (50 km/h).

1.31

METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (5/6)

In the following examples, the pre­tensioners or the airbags could op­erate:

– impact under vehicle such as pave-

ment;
– potholes;
– drop or hard landing;
– stones;
– ...

1.32

In the following examples, there is a
risk that pretensioners orairbags may

not be triggered:

– rear impact, however severe;
– the vehicle overturning;

– side impact to the front or rear of the

vehicle;

– frontal impact, under the tail of a

lorry;

– frontal impact against an obstacle

with a sharp angle;

– ...

METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (6/6)

All of the warnings below are given so that the airbag is not obstructed in any way when it is inflated and also to prevent
the risk of serious injuries caused by items which may be dislodged when it inflates.

Warnings concerning the driver’s airbag

– Do not modify the steering wheel or the steering wheel boss.

– Do not cover the steering wheel boss under any circumstances.
– Do not attach any objects (badge, logo, clock, telephone holder, etc.) to the steering wheel boss.
– The steering wheel must not be removed (except by qualified personnel from our Network).
– Do not sit too close to the steering wheel when driving: sit with your arms slightly bent (see “Adjusting your driving position”

➥ 1.23). This will allow sufficient space for the airbag to deploy correctly and be fully effective.

Warnings concerning the passenger airbag

– Do not attach or glue any objects (badge, logo, clock, telephone holder, etc.) to the dashboard on or near the airbag.
– Do not place anything between the dashboard and the passenger (pet, umbrella, walking stick, parcels, etc.).
– The passenger must not put his or her feet on the dashboard or seat as there is a risk that serious injuries may occur. In

general, parts of the body should be kept away from the dashboard (knees, hands, head, etc.).

– The devices in addition to the front passenger seat belt should be reactivated as soon as a child seat is removed, to ensure

the protection of the passenger in the event of an impact.

A REAR-FACING CHILD SEAT MUST NOT BE FITTED TO THE FRONT PASSENGER SEAT UNLESS THE

RESTRAINT SYSTEMS IN ADDITION TO THE FRONT PASSENGER SEATBELT ARE DEACTIVATED ➥ 1.51.

1.33

METHODS OF RESTRAINT IN ADDITION TO THE REAR SEAT BELTS

Depending on the vehicle, they will con­sist of:

– side seat belt inertia reel preten-

sioners;

– chest force limiters.

These systems are designed to act in­dependently or together when the vehi­cle is subjected to a frontal impact.

Depending on the severity of the
impact, the system can trigger:

– seat belt locking;
– the seat belt inertia reel pretensioner

(which engages to correct seat belt
slack).

Force limiter

Above a certain severity of impact, this
mechanism is used to limit the force of
the belt against the body so that it is at
an acceptable level.

1

Side seat belt pretensioners

The pretensioners hold the seat belt
against the body, holding the occupant
more securely against the seat, thus in­creasing the seat belt’s efficiency.

With the ignition on, following a signif­icant frontal impact and depending on
the severity of the impact, the system
may trigger the seat belt inertia reel
pretensioner 1, which instantly retracts
the seat belt.

– Have the entire restraint

system checked following
an accident.

– No operation whatso­ever is permitted on any part
of the system (pretensioners,
airbags, computers, wiring) and
the system components must not
be reused on any other vehicle,
even if identical.

– Only qualified personnel from our

Network may work on the airbags;
otherwise the system may trigger
accidentally and cause injury.

– The electric trigger system may

only be tested by a specially
trained technician using special
equipment.

– When the vehicle is scrapped,

contact an approved dealer for
disposal of the pretensioner and
airbags gas generators.

1.34

SIDE PROTECTION DEVICES

Side Airbag

This airbag may be fitted to each of the
front seats and is activated at the sides
of the seats (door side) to protect the
occupants in the event of a severe side
impact.

Curtain Airbag

This is an airbag fitted (depending on
the vehicle) along the upper sides of
the vehicle – they inflate along the front
and rear door side windows to protect
the passengers in the event of a severe
side impact.

Warning relating to the side airbag
– Fitting seat covers: seats equipped with an airbag require covers spe-

cifically designed for your vehicle. Contact an approved dealer to find

out if these covers are available. The use of any covers other than those
designed for your vehicle (including those designed for another vehicle) may
affect the operation of the airbag and reduce your protection.

– Do not place any accessories, objects or even pets between the seatback, the

door and the internal fittings. Do not cover the seatback with any items such as
clothes or accessories. This may prevent the air bag from operating correctly
or cause injury when the airbag is deployed.

– No work or modification whatsoever may be carried out on the seat or internal

fittings, except by qualified personnel from an approved Dealer.

– This airbag operates through slits in the front seatbacks (door side): never

insert any objects in these slits.

1.35

ADDITIONAL METHODS OF RESTRAINT

All of the warnings below are given so that the airbag is not obstructed in any way when it is inflated and also to prevent
the risk of serious injuries caused by items which may be dislodged when it inflates.

The airbag is designed to complement the action of the seat belt. Both the airbag and the seat belt are integral parts
of the same protection system. It is therefore essential to wear seat belts at all times. If seat belts are not worn, the oc­cupants are exposed to the risk of serious injury in the event of an accident. It may also increase the risk of minor su­perficial injuries occurring when the airbag is deployed, although such minor injuries are always possible with airbags.

If the vehicle should overturn or in the event of a rear impact, however severe, the pretensioners and airbags are not always
triggered. Impacts to the underside of the vehicle, e.g. from pavements, potholes or stones, can all trigger these systems.

– No work or modification whatsoever may be carried out on any part of the airbag system (airbags, pretensioners, computer,

wiring harness, etc.), except by qualified Network personnel.

– To ensure that the system is in good working order and to avoid accidental triggering of the system which may cause injury,

only qualified Network personnel may work on the airbag system.

– As a safety precaution, have the airbag system checked if your vehicle has been involved in an accident, or is stolen or

broken into.
– When selling or lending the vehicle, inform the user of these points and hand over this handbook with the vehicle.
– When scrapping your vehicle, contact your approved Dealer for disposal of the gas generator(s).

1.36

CHILD SAFETY: General information (1/2)

Carrying children

Please ensure that you comply with the
legislation of your country.

Children, and adults, must be correctly
seated and strapped in for all journeys.
The children being carried in your vehi­cle are your responsibility.

A child is not a miniature adult. Children
are at risk of specific injuries as their
muscles and bones have not yet fin­ished growing. The seat belt alone
would not provide suitable protection.
Use an approved child seat and ensure
you use it correctly.

To prevent the doors being
opened, use the “Child lock”
feature. ➥ 1.14.

Special features of LPG
versions

The vehicle’s LPG installa-

tion may lead to changes to
the vehicle’s features compared to
the petrol version.

This may relate to the number of
seats and the installation of child
seats.

Please contact an authorised dealer.

A collision at 30 mph (50

km/h) is the same as fall-

ing a distance of 10 metres.

Transporting a child without
a restraint is the equivalent of allow­ing him or her to play on a fourth­floor balcony without railings.
Never travel with a child held in your
arms. In the event of an accident,
you will not be able to keep hold of
the child, even if you yourself are
wearing a seat belt.
If your vehicle has been involved in
a road accident, replace the child
seat and have the seat belts and
ISOFIX anchorage points checked.

Driver’s responsibility
when parking or stopping
the vehicle

Never leave an animal,
child or adult who is not self-suffi­cient alone on your vehicle, even for
a short time.

They may pose a risk to themselves
or to others by starting the engine,
activating equipment such as the
electric windows or by locking the
doors.

Also, in hot and/or sunny weather,
please remember that the tempera­ture inside the passenger compart­ment increases very quickly.

RISK OF DEATH OR SERIOUS
INJURY.

1.37

CHILD SAFETY: General information (2/2)

Using a child seat

The level of protection offered by the
child seat depends on its ability to re­strain your child and on its installation.
Incorrect installation compromises the
protection it offers the child in the event
of harsh braking or an impact.

Before purchasing a child seat, check
that it complies with the regulations for
the country you are in and that it can
be fitted in your vehicle. Consult an ap­proved dealer to find out which seats
are recommended for your vehicle.

Before fitting a child seat, read the
manual and respect its instructions. If
you experience any difficulties during
installation, contact the manufacturer
of the equipment. Keep the instructions
with the seat.

Set a good example by always fas­tening your seat belt and teaching
your child:
– to strap themselves in correctly;
– to always get in and out of the car

at the kerb, away from busy traf­fic.

Do not use a second-hand child
seat or one without an instruction
manual.

Check that there are no objects in
the vicinity of the child seat which
could impede its operation.

Never leave a child unat­tended in the vehicle.
Check that your child is

always strapped in and that
the belt or safety harness used is
correctly set and adjusted. Avoid
wearing bulky clothing which could
cause the belts to slacken.
Never let your child put their head or
arms out of the window.
Check that the child is in the correct
position for the entire journey, espe­cially if asleep.

1.38

CHILD SAFETY: choosing a child seat

Rear-facing child seats

A baby’s head is, proportionally, heavier
than that of an adult and its neck is very
fragile. Transport the child in this po­sition for as long as possible (until the
age of 2 at the very least). It supports
both the head and the neck.

Choose a bucket type seat for best side
protection and change it as soon as the
child’s head is higher than the shell.

Forward-facing child seats

Up to 18 kg or 4 years, the child may
travel on a forward-facing seat. Choose
a seat according the child’s size: their
head and abdomen are the areas which
must be most protected. A forward-fac­ing child seat which is firmly attached to
the vehicle will reduce the risk of impact
to the head. Ensure your child travels in
a forward-facing seat with a harness for
as long as their size permits.

Choose a bucket type seat for optimum
side protection.

Booster cushions

From 15 kg or 4 years, the child can
travel using a booster seat, which will
enable the seat belt to be adapted
to suit his/her size and shape. The
booster seat cushion must be fitted with
guides to position the seat belt on the
child’s thighs rather than the stomach.
It is recommended that you use a seat­back fitted with a belt strap guide which
can be adjusted in terms of height to
position the seat belt in the centre of the
shoulder. It must never rest on the neck
or on the arm.

Choose a bucket type seat for optimum
side protection.

1.39

CHILD SAFETY: choosing a child seat mounting (1/3)

There are two ways of attaching child
seats: via the seat belt or using the
ISOFIX system.

Attachment via the seat belt

The seat belt must be adjusted to
ensure that it is effective in the event of
harsh braking or an impact.

Ensure that the strap paths indicated
by the child seat manufacturer are re­spected.

Always check that the seat belt is cor­rectly fastened by pulling it up, then
pulling it out fully whilst pressing on the
child seat.

Check that the seat is correctly held by
moving it from side to side and back
to front: the seat should remain firmly
fixed.

Check that the child seat has not been
installed at an angle and that it is not
resting against a window.

Do not use the child seat

if it may unfasten the seat

belt restraining it: the base

of the seat must not rest on
the buckle and/or catch of the seat
belt.

The seat belt must never
be twisted or the tension
relieved. Never pass the

shoulder strap under the
arm or behind the back.
Check that the seat belt has not
been damaged by sharp edges.
If the seat belt does not operate nor­mally, it will not protect the child.
Consult an approved dealer. Do not
use this seat until the seat belt has
been repaired.

1.40

CHILD SAFETY: choosing a child seat mounting (2/3)

Attachment using the ISOFIX
system

Approved child seats ISOFIX are stand­ardised in accordance with current reg­ulations if any of the four cases below
applies:
– ISOFIXuniversal 3-point forward-fac-

ing seat;
– ISOFIXsemi-universal 2-point seat;
– specific;
– i-Size which has either:
– a strap which attaches to the third

ring of the seat concerned;

– or a strut that rests on the vehi-

cle floor, compatible with the ap­proved seat i-Size, the role of
which is to prevent the child seat
from moving in the event of a col­lision.

In the latter three cases check that your
child seat can be installed by consulting
the list of compatible vehicles.

Attach the child seat with the ISOFIX
locks, if these are provided. The ISOFIX
system allows quick, easy, safe fitting.

The ISOFIX system consists of 2 rings
and, in some cases, a third ring.

The ISOFIX anchorage
points have been exclu­sively designed for child

seats with the ISOFIX
system. Never fit a different type of
child seat, seat belt or other objects
to these anchorage points.
Check that nothing is obstructing
the anchorage points.
If your vehicle has been involved in
a road accident, have the ISOFIX
anchorage points checked and re­place your child seat.

1

The two rings are located behind the
zip fasteners 1 between the seat back
and seat base and are identified by a

 marking.

No modifications may be
made to the component
parts of the restraint system

(seat belts, ISOFIX and
seats and their mountings) originally
fitted.

Before using an ISOFIX child seat that you purchased for another vehi­cle, check that its installation is authorised. Consult the list of vehicles
which can be fitted with the seat from the equipment manufacturer.

1.41

CHILD SAFETY: choosing a child seat mounting (3/3)

2

3

4

Attachment using the ISOFIX
system (continued)

The third ring 4 is used to attach the
upper strap 2 on some child seats.

Rear seats

The upper strap 2 should be positioned
between the seatback and the rear
parcel shelf. To do so, remove the rear
parcel shelf ➥ 3.38.
Attach the 3 hook on one of the 4 rings

marked with the

 symbol.

2

3

4

Front passenger seat

Attach the 3 hook of the upper strap 2 to
the ring 4 marked with the

All seats

Pull the upper strap 2 so that the back
of the child seat comes into contact with
the back of the vehicle seat.

 symbol.

The ISOFIX anchorage
points have been exclu­sively designed for child

seats with the ISOFIX
system. Never fit a different type of
child seat, seat belt or other objects
to these anchorage points.
Check that nothing is obstructing
the anchorage points.
If your vehicle has been involved in
a road accident, have the ISOFIX
anchorage points checked and re­place your child seat.

Check that the seatback

of the forward-facing child

seat is in contact with the

back of the vehicle seat.
In this case, the child seat may not
always rest on the base of the vehi­cle seat.

1.42

CHILD SAFETY: fitting a child seat, general information (1/2)

Some seats are not suitable for fitting
child seats. The diagram on the follow­ing page shows you how to attach a
child seat.

Fit the child seat in a rear
seat wherever possible.

Make sure the child seat or

the child’s feet do not pre­vent the front seat from locking cor­rectly. ➥ 1.21.

Check that when installing the child
seat in the vehicle it is not at risk of
coming loose from its base.

If you have to remove the headrest,
check that it is correctly stored so
that it does not come loose under
harsh braking or impact.

Always attach the child seat to the
vehicle even if it is not in use so that
it does not come loose under harsh
braking or impact.

The types of child seat indicated may
not be available. Before using a differ­ent child seat, check with the manufac­turer that it can be fitted.

In the front seat

The laws concerning children travel­ling in the front passenger seat differ in
every country. Consult the legislation in
force and follow the indications on the
diagram on the following page.

Before fitting a child seat in this seat (if
authorised):

– lower the seat belt as far as possible;
– move the seat as far back as possi-

ble;

– gently tilt the seatback away from

vertical (approximately 25°);

– on equipped vehicles, raise the seat

base as far as possible.

Always fully raise the seat headrest so
that it does not interfere with the child
seat ➥ 1.92.

After installing the child seat, when this
is possible, you can move the vehi­cle seat forward if necessary (so as to
leave enough space in the rear seats
for passengers or other child seats).
For a rear-facing child seat, do not let
it touch the dashboard or move it to the
furthest forward position.

Do not change other settings after in­stalling the child seat.

RISK OF DEATH OR
SERIOUS INJURY: before

fitting a rear-facing child

seat in this seat, make sure
that the front passenger airbag has
been deactivated. ➥ 1.51.

1.43

CHILD SAFETY: fitting a child seat, general information (2/2)

In the rear side seat

A carrycot can be installed across the
vehicle and will take up at least two
seats. Position the child with his or her
feet nearest the door.

Move the front seat as far forward as
possible to install a rear-facing child
seat, then move back the seat in front
as far as it will go, although without al­lowing it to come into contact with the
child seat.

For the safety of the child in the for­ward-facing position:
– move the relevant seat backwards

as far as possible;

– move the seat in front of the child

forwards, and set the position of the
seatback to avoid contact between
the seat and the child’s legs.

Ensure that the child seat
or the child’s feet do not
prevent the front seat from
locking correctly. ➥ 3.35 or

➥ 1.21.

Always remove the headrest from the
rear seat on which the child seat is
positioned. ➥ 3.34. If necessary, posi­tion the rear seat as far back as pos­sible. This must be done before fitting
the child seat. Check that the child seat
is resting against the back of the rear
seat.

A child seat with floor sup­ports must never be in­stalled on the rear centre
seat.

RISK OF DEATH OR SERIOUS
INJURY.

When fitting a child seat
(Group 2 or 3 booster seat),
check that the seat belts

operate (wind) correctly
➥ 1.23. If necessary, adjust the posi­tion of the vehicle seat.

Fit the child seat in a rear
seat wherever possible.

To install an ISOFIX seat in

this seat, unbuckle the seat
belt by hand before engaging the
bolts.

Fitting a seat ISOFIX in

the rear-left seat means

the middle seat cannot be

used. The central seat belt
will no longer be either accessible or
useable.

1.44

CHILD SEATS: attachment by seat belt (1/3)

Fitting diagram

Using a child safety system

RISK OF DEATH OR
SERIOUS INJURY: before

fitting a rear-facing child

seat in this seat, make sure
that the front passenger airbag has
been deactivated. ➥ 1.51.

They risk serious or even fatal injury.

which is not approved for
this vehicle will not correctly
protect the baby or child.

³ Check the status of the airbag

before fitting a child seat or allowing a
passenger to use the seat.

²

Child seat attached using the belt

Seat not suitable for fitting
child seats.

¬ Seat which allows a child seat

with “Universal” approval to be attached
by a seat belt.

1.45

CHILD SEATS: attachment by seat belt (2/3)

The table below summarises the information already shown on the diagram on the previous page, to ensure the regula­tions in force are respected.

Five-seater version

Front passenger seat

Type of child seat Weight of the child

Carrycot fitted
across the vehicle

Group 0

Rear-facing shell
seat

Groups 0 or 0 +

Shell seat/rear-facing
seat

Groups 0+ and 1

< 10 kg X X U (2) X

< 10 kg and < 13 kg U (1) (5) X U (3) X

< 13 kg and 9 to 18 kg U (1) (5) X U (3) X

With airbag disabled

With airbag

activated

Rear side

seats

Rear centre

seat

Forward-facing seat

Group 1

Booster seat

Groups 2 and 3

(1) RISK OF DEATH OR SERIOUS INJURY: before fitting a rear-facing child seat in this seat, make sure that the front

passenger airbag has been deactivated. ➥ 1.51.

1.46

9 to 18 kg X U (5) U (4) X

15 to 25 kg and 22 to
36 kg

X U (5) U (4) X

CHILD SEATS: attachment by seat belt (3/3)

X = Seat not suitable for fitting child seats of this type.
U = Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted.
(2) A carrycot can be installed across the vehicle and will take up at least two seats. Position the child with his or her feet nearest

the door.

(3) If necessary, position the vehicle seat as far back as possible. In order to install a rear-facing child seat, move the front seat

as far forward as possible, then move the front seat back as far as it will go, without allowing it to come into contact with the
child seat.

(4) In all situations, remove the rear headrest of the seat on which the child seat is positioned. This must be done before fitting the

child seat. ➥ 3.34. Move the seat in front of the child forwards, move the seatback forward to avoid contact between the seat
and the child’s legs.

(5) Raise the seat to the maximum and position it as far back as possible, tilting the seatback slightly (approximately 25°).

1.47

CHILD SEATS: fitted using theISOFIX SYSTEM (1/3)

The table below summarises the information already shown in the diagram on the following pages, to ensure the appli­cable regulations are respected.

Front passenger seat

Type of child seat

Carrycot fitted
across the vehicle

Group 0

Rear-facing shell
seat

Groups 0 or 0 +

Shell seat/rear-facing
seat

Groups 0+ and 1

Forward-facing seat

Group 1

Booster seat

Groups 2 and 3

Seat i-Size i-U (1) (4) i-UF (1) i-U (2) (3) X

Weight of

the child

< 10 kg

< 13 kg

< 13 kg and 9 to
18 kg

9 to 18 kg

15 to 25 kg and
22 to 36 kg

Seat size

ISOFIX

F, G

[L1, L2]

E

[R1]

C, D

[R3, R2]

A, B, B1

[F3, F2, F2X]

[B2] X IUF - IL (1) IUF - IL (2) (3) X

Without airbag

or with airbag

deactivated

X X X X

IL (1) (4) X IL (2) X

IL (1) (4) X IL (2) X

X IUF - IL (1) IUF - IL (2) (3) X

With airbag

activated

Rear side

seats

Rear centre

seat

1.48

CHILD SEATS: fitted using theISOFIX SYSTEM (2/3)

X = Seat not suitable for fitting child seats of this type.
IUF/IL = On equipped vehicles, seat which allows an approved “Universal/semi-universal” or “vehicle specific” child seat to be at-

i-U = Suitable for “universal” front-facing and rear-facing i-Size restraint devices.
i-UF = Suitable only for “universal” front-facing and rear-facing i-Size restraint devices.
(1) Raise the seat to the maximum and position it as far back as possible, tilting the seatback slightly (approximately 25°).
(2) If necessary, position the vehicle seat as far back as possible. In order to install a rear-facing child seat, move the front seat

(3) In all situations, remove the rear headrest of the seat on which the child seat is positioned. This must be done before fitting the

The size of the ISOFIX child seat is indicated by a letter:
– A, B, B1 [F3, F2, F2X]: for forward-facing seats in Group 1 (9 to 18 kg);
– CandD [R3,R2]: rear-facing seats or shell seats in Group 0+ (less than 13 kg) or Group 1 (9 to 18 kg);
– E [R1]: rear-facing shell seats in group 0 (less than 10 kg) or 0+ (less than 13 kg);
– F, G [L1, L2]: carrycots in group 0 (less than 10 kg);
– [B2]: boosters in groups 2 and 3 (15 to 25 kg and 22 to 36 kg).

tached using the ISOFIX system; check that it can be fitted.

as far forward as possible, then move the front seat back as far as it will go, without allowing it to come into contact with the
child seat.

child seat. ➥ 3.34. Move the seat in front of the child forwards, move the seatback forward to avoid contact between the seat
and the child’s legs.

(4) RISK OF DEATH OR SERIOUS INJURY: before fitting a rear-facing child seat in this seat, make sure that the front

passenger airbag has been deactivated. ➥ 1.51

1.49

CHILD SEATS: fitted using theISOFIX SYSTEM (3/3)

Fitting diagram

For the front passenger seat, the
use of a child seat with a floor sup­port is recommended to avoid trig­gering the seat belt warning signal.

Using a child safety system

which is not approved for

this vehicle will not correctly

protect the baby or child.
They risk serious or even fatal injury.

²

Seat which does not allow a
child seat to be fitted.

RISK OF DEATH OR
SERIOUS INJURY:

before fitting a rear facing

child seat on the front pas­senger seat, check that the airbag
has been deactivated ➥ 1.51

Child seat fitted using the ISOFIX
mounting

 Seat which allows an ISOFIX

child seat to be fitted.

± The rear seats are fitted with

an anchorage point which allows a
forward-facing ISOFIX child seat with
universal approval to be attached. The
anchoring points are located on the
passenger seatback for the front seat
and on the bench seatback for the rear
seats.

Fit the child seat in a rear
seat wherever possible.

To install an ISOFIX seat in

this seat, unbuckle the seat
belt by hand before engaging the
bolts.

Fitting a seat ISOFIX in

the rear-left seat means

the middle seat cannot be

used. The central seat belt
will no longer be either accessible or
useable.

1.50

CHILD SAFETY: deactivating, activating AIRBAG front passenger (1/3)

1

Deactivating the front
passenger airbag

Before installing a child seat on the
front passenger seat:

– check that the child seat can be in-

stalled on this seat;

– it is essential to deactivate the

airbagfor a rear-facing child seat.

2

To deactivate the airbag: stationary
vehicle, ignition off, push and turn

lock 1 to the OFF position.
With the ignition on, you must check

that the warning light
display 2.

This light remains permanently lit to
let you know that you can fit a child
seat.

¹ is lit on the

The passenger airbag must

only be activated or deacti-

vated when the vehicle is

stationary with the igni­tion off.

If it is interfered with when the ve­hicle is being driven, indicator lights

å and © will come on.

Switch the ignition off then on again
to reset the airbag in accordance
with the lock position.

DANGER

Since operation of the front

passenger airbag is not

compatible with the po­sition of a rear-facing child seat,
NEVER fit a rear-facing child re­straint system in a seat protected
by an ACTIVATED front AIRBAG.
This can lead to the DEATH of the
CHILD or SERIOUS INJURY.

1.51

CHILD SAFETY: deactivating, activating AIRBAG front passenger (2/3)

3

A

DANGER

Since operation of the front
passenger airbag is not

compatible with the po­sition of a rear-facing child seat,
NEVER fit a rear-facing child re­straint system in a seat protected
by an ACTIVATED front AIRBAG.
This can lead to the DEATH of the

CHILD or SERIOUS INJURY.

A

The markings on the dashboard and
labels A on each side of the passen­ger sun visor 3 (example: label shown
above) remind you of these instruc­tions.

1.52

CHILD SAFETY: deactivating, activating AIRBAG front passenger (3/3)

Operating faults

It is forbidden to fit a rear-facing child
seat to the front passenger seat if the
airbag activation/deactivation system is
faulty.

1

2

Allowing any other passenger to sit in
that seat is not recommended.

Contact your approved dealer as soon
as possible.

Activating the front
passenger airbag

You should reactivate the airbag as
soon as you remove the child seat from
the front passenger seat to ensure the
protection of the front passenger in the
event of an impact.

To reactivate the airbag: with the
vehicle stoppedand the ignition off,

push and turn lock 1 to the ON position.
With the ignition switched on, you must

check that the warning light

out and that the warning light
comes on the display 2 after each start­up for around 60 seconds.

The front passenger airbag is activated.

¹ is



The passenger airbag may
only be activated or deacti­vated when the vehicle is

stationary with the igni-

tion off.

If it is interfered with when the ve­hicle is being driven, indicator lights

å and © will come on.

Switch the ignition off then on again
to reset the airbag in accordance
with the lock position.

1.53

DRIVING POSITION: LEFT-HAND DRIVE (1/2)

28

1 2 3

27

26

25

23

24

18

22

19

20

21

18

16

7

9

12

1085 64 7

11

1

13

14

15

17

1.54

DRIVING POSITION: LEFT-HAND DRIVE (2/2)

The equipment fitted, described below, DEPENDS ON THE VERSION AND COUNTRY.

1 Side air vents.
2 Stalk for:

– direction indicator lights;
– exterior lights;

– rear fog lights.
3 Instrument panel.
4 Driver airbag and horn location.
5 Controls for:

– on-board computer information

read-out and vehicle settings
customisation menu,

– remote radio and navigation

system.

6 Steering column stalk for wind-

screen and rear screen wash/

wiper.
7 Centre air vents.
8 Multimedia screen.
9 Heating or air conditioning con-

trols.
10 Passenger airbag location.
11 Glove compartment

12 Controls for:

– front seat heating;
– activation/deactivation of the

Stop and Start function;

– activation/deactivation, depend-

ing on the vehicle, of the ECO or

MULTI-SENSE mode;
– hazard warning lights;
– electric door locking;
– activation/deactivation of the

parking distance control;
– activating/deactivating the 360°

camera;
– ...

13 USB sockets.
14 Storage compartment.
15 Gearstick.
16 Parking position button on the au-

tomatic gearbox.

17 Controls for:

– activating/deactivating the elec-

tronic parking brake;
– activation/deactivation of the

function autohold.

18 “Hands-free” card holder.
19 Handbrake.

20 Charging zone/telephone storage.
21 Accessories socket.
22 Engine start/stop button.
23 Control for adjusting steering

wheel height and reach.
24 Automatic gearbox paddles
25 Bonnet release control.
26 Main switch and controls for cruise

control/speed limiter and Stop and

Go adaptive cruise control.
27 LPG control.
28 Controls for:

– lighting rheostat for control

instru- ments;

– headlight beam height remote

adjustment;

– activation/deactivation of the

steering wheel heating;

– activation/deactivation of Lane

Keeping Assist/Lane Departure
Warning;

– heated windscreen.

1.55

DRIVING POSITION: RIGHT-HAND DRIVE (1/2)

28

1

2

27

3 7

26

4

25

24

23

6

4

18

17

19

20

21

22

16

95

8

10

15

11 12

1

13

14

1.56

DRIVING POSITION: RIGHT-HAND DRIVE (2/2)

The equipment fitted, described below, DEPENDS ON THE VERSION AND COUNTRY.

1 Side air vents.
2 Passenger airbag location.
3 Heating or air conditioning con-

trols.
4 Centre air vents.
5 Multimedia screen.
6 Controls for:

– front seat heating;
– activation/deactivation of the

Stop and Start function;

– activation/deactivation, depend-

ing on the vehicle, of the ECO or

MULTI-SENSE mode;
– hazard warning lights;
– electric door locking;
– activation/deactivation of the

parking distance control;
– activating/deactivating the 360°

camera;
– ...

7 Stalk:

– direction indicator lights;
– exterior lights;
– rear fog lights.

8 Main switch and controls for cruise

control/speed limiter and Stop and
Go adaptive cruise control.

9 Instrument panel.

10 Driver airbag and horn location.
11 Controls for:

– on-board computer information

read-out and vehicle settings
customisation menu,

– remote radio and navigation

system.

12 Steering column stalk for wind-

screen and rear screen wash/
wiper.

13 Controls for:

– lighting rheostat for control

instru- ments;

– headlight beam height remote

adjustment;

– activation/deactivation of the

steering wheel heating;

– activation/deactivation of Lane

Keeping Assist/Lane Departure
Warning;

– heated windscreen
14 LPG control.
15 Automatic gearbox paddles.
16 Control for adjusting steering

wheel height and reach.

17 Engine start/stop button.
18 USB sockets.
19 Gearstick.
20 Parking position button on the au-

tomatic gearbox.
21 Charging zone/telephone storage
22 Controls for:

– activating/deactivating the elec-

tronic parking brake;

– activation/deactivation of the

function autohold.
23 “Hands-free” card holder.
24 Handbrake.
25 Storage compartment.
26 Accessories socket.
27 Glovebox.
28 Bonnet release control.

1.57

WARNING LIGHTS (1/6)

The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.

A

1

Instrument panel A, B or C : it illumi-

nates when the ignition is switched on.
Press or lift the 1 switch as many times
as required to adjust the intensity.

Warning light © means you

should drive very carefully to an

authorised dealer as soon as
possible. If you fail to follow this

recommendation, you risk damag­ing your vehicle.

B

A

B

1 1

In some cases, the appearance of a
warning light is accompanied by a mes­sage on the instrument panel.

For your safety, the warning
light

® requires you to

stop immediately as soon

Switch off the engine and do not re­start it. Call an approved Dealer.

as traffic conditions allow.

C

If no lights or sounds are ap­parent, this indicates a fault
in the instrument panel. This

indicates that it is essential
to stop immediately (as soon as traf­fic conditions allow). Ensure that the
vehicle is correctly immobilised and
contact an approved Dealer.

1.58

WARNING LIGHTS (2/6)

The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.

š
á
k


–
˜

Side light warning light

Main beam headlight tell­tale

Dipped beam headlight tell­tale

Rear fog lights tell-tale

Automatic main beam head­light indicator light ➥ 1.93

Left-hand direction indicator
tell-tale

Right-hand direction indica­tor tell-tale light

å

the engine is switched on and goes off
after a few seconds.

If it does not come on when the igni­tion is switched on, or comes on when
the engine is running, there is a fault in
the system.

Contact your approved Dealer as soon
as possible.

®

tion or engine is switched on and goes
out as soon as the engine is running. It
comes on with other warning lights and/
or messages, and is accompanied by
a beep.

It requires you to stop immediately, for
your own safety, as soon as traffic con­ditions allow. Switch off the engine and
do not restart it.

Contact an approved Dealer.

Indicator lightairbag

It lights up when the ignition or

STOP light

This lights up when the igni-

D

It lights up when the ignition or the
engine is switched on and goes off after
a few seconds.

If it comes on during braking and is ac­companied by the

and a beep, it indicates that the fluid
level in the circuit is low or that there is
a braking system fault.

Stop as soon as traffic conditions allow
and consult an approved dealer.

Ú

the engine is switched on and goes off
after a few seconds.

If it comes on on the road, accompa­nied by the

beep, this indicates an overload or dis­charge in the electrical circuit.

Stop as soon as traffic conditions allow
and contact an approved Dealer.

Brake circuit fault warning
light

® warning light

Battery charge warning light

It lights up when the ignition or

® warning light and a

1.59

WARNING LIGHTS (3/6)

The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.

À

the engine is switched on and goes off
after a few seconds.

If it comes on on the road, accompa­nied by the

a beep, stop immediately and cut the
ignition.

Check the oil level. If the level is normal,
the warning light is related to something
else.

Call an approved Dealer.

U

It lights up when the ignition or the
engine is switched on and goes off after
a few seconds.

If it comes on while driving, alongside
the warning light

there is a system fault.
Contact an authorised dealer.



Oil pressure warning light

It lights up when the ignition or

® warning light and

Variable power-assisted
steering warning light

®, this means

“AUTOHOLD” system warn­ing ➥ 2.29

©

tion or engine is switched on and goes
out as soon as the engine is running.
It can light up in conjunction with other
warning lights and/or messages on the
instrument panel. It means you should
drive very care- fully to an approved
Dealer as soon as possible. If you fail
to follow this recommendation, you risk
damaging your vehicle.



ing and is accompanied by the
indicator light, you must, for your safety,
stop as soon as traffic conditions allow.
Switch off the engine and do not restart
it. Call an approved Dealer. If it appears
in yellow during driving and is accom-

panied by the
an approved dealer as soon as possi­ble. Meanwhile, drive with care.

Warning light

This lights up when the igni-

Warning light

If it appears in red during driv-

®

© warning light, visit

If you fail to follow this recommenda­tion, you risk damaging your vehicle.

}

ing light ➥ 2.24 ➥ 2.25



you to change to a higher gear (arrow
pointing upwards) or lower gear (arrow
pointing downwards) ➥ 2.30.



(ESC) and traction control system
It lights up when the ignition or the

engine is switched on and goes off after
a few seconds.

There are several reasons for the warn­ing light to appear: ➥ 2.46.



ity program (ESC) and traction con­trol system

2

Handbrake “on” and elec­tronic parking brake warn-

Gear change indicators

This lights up to advise

Warning light for the elec­tronic stability program

Warning light for non-availa­bility of the electronic stabil-

Door status warning light

1.60

WARNING LIGHTS (4/6)

The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.

x

It lights up when the ignition or the
engine is switched on and goes off after
a few seconds.
If it lights up when you are driving, it in­dicates a fault in the anti-lock braking
system.

Braking will then be as normal, without
the ABS. Contact an approved Dealer
as soon as possible.




haust gas reduction system ➥ 1.113



Anti-lock braking warning
light

Particle filter system warn­ing light ➥ 2.16 ➥ 2.22

Warning light for reagent
level and faults in the ex-

Tyre pressure loss warning

➥ 2.40

É

This should come on when the igni­tion is switched on. It indicates that the
heater plugs are in operation.

It goes out when preheating is com­plete. The engine can be started.

Ä

On vehicles that are equipped, this light
comes on when the engine is started
and, depending on the vehicle, when
the ignition is switched off while the
engine is in the standby phase ➥ 2.12
then it goes out.
– If it lights up continuously, consult

– If it flashes, reduce the engine speed

L

nition or the engine is switched on and
goes off after a few seconds.

Preheating warning light
(Diesel version)

Toxic Fume Filter System
Warning Light

your approved dealer as soon as
possible;

until the light stops flashing. Contact
your approved Dealer as soon as
possible ➥ 2.38.

Low fuel level warning light

It lights up orange when the ig-

If the light becomes orange while driv­ing and a beep sounds, fill up with fuel
as soon as possible. There is only ap­proximately 31 miles (50 km) worth of
fuel left.



is active ➥ 2.30.



wheel” parameter is activated (ON) in
the user settings ➥ 2.30.

This warning light is displayed when the
function is activated:

– in grey when the vehicle is not in

– in green or, depending on the vehi-

Note: depending on the vehicle, on
vehicles equipped with Multi-Sense,
activation/deactivation is carried out
by configuring the various My Sense
modes or ECO mode.

Mode warning light ECO
It comes on when ECO mode

Freewheel indicator light

It activates when the “Free-

freewheel mode;

cle, when the vehicle is in freewheel
mode (automatic neutral).

1.61

WARNING LIGHTS (5/6)

The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.

Ô

This lights up blue when you switch on
the ignition or start the engine.

If it turns red, stop and let the engine
idle for a minute or two.

The temperature should lower and the
warning light should return to a blue
colour. If not, stop the engine. Let the
engine cool down before checking the
coolant.
Contact an approved Dealer.

Coolant temperature warn­ing light

Ð
Ï


➥ 2.103



Ó

pedal should be depressed ➥ 2.134.

Speed limiter warning light
➥ 2.94

Cruise control warning light
➥ 2.98

Adaptive cruise control
warning light Stop and Go

Engine standby warning
light ➥ 2.12

Unavailability of engine
standby warning light ➥ 2.12

Brake pedal warning light

This lights up when the brake








unavailability of active emergency
braking ➥ 2.82



the steering wheel ➥ 2.56

Assisted parking brake fault
light ➥ 2.129

Overspeed warning light

➥ 1.64

Lane departure system
warning light ➥ 2.51

Lane Keeping Assist system
warning light ➥ 2.56

(Depending on vehicle)
Indicator of failure or

Warning light to indicate de­tected presence of hands on

1.62

WARNING LIGHTS (6/6)

The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.

On display D


¹

Passenger Airbag ON
➥ 1.51

Passenger Airbag OFF
➥ 1.51

ß

D

Seat belt reminder warning
lights ➥ 1.23

1.63

DISPLAYS AND INDICATORS (1/7)

Instrument panel in miles

(option to switch to km/h)

Vehicles not fitted with a multimedia
screen

– With the ignition off, press the 2

switch as many times as required to
reach the vehicle tab 5;

– press 3 or 4 repeatedly to access

2

3

“Settings”, then press 1 “OK”;

– repeat the same operation to access

“DASHBOARD”, then “Units”.

5

1

4

Engine oil level low warning

When the engine is started, the instru­ment panel display alerts you if the min­imum oil level is reached. ➥ 4.4.

The first time the warning appears, it
can be cleared by pressing 1 "OK ".

Subsequent warnings will disappear
automatically after around 30 seconds.

1.64

Vehicles fitted with a multimedia
screen.

Please refer to the multimedia instruc­tions to select the audio system.

Note: in both cases, once the battery
is switched off, the on-board computer
automatically returns to the original unit
of measurement.

To return to the previous mode, repeat
the same operation.

Please refer to the multimedia instruc­tions for more information.

DISPLAYS AND INDICATORS (2/7)

A

Instrument panel A

It lights up when the ignition is switched
on. In some cases, the appearance of a
warning light is accompanied by a mes­sage.
Depending on the vehicle, you can cus­tomise your instrument panel with the
content and colours of your choice.
For vehicles fitted with a multimedia
screen, refer to the multimedia instruc­tions.
For vehicles not fitted with a multimedia
screen ➥ 1.83.

Speedometer 6

6

11

Rev counter 7
(graduations x 1000)

Depending on the selected customisa­tion, it may not be displayed.

Overspeed buzzer

Depending on the vehicle and coun-

try, the
played and a beep sounds. This beep
sounds as soon as the vehicle is trav­elling at over 75 mph (120 km/h). This
warning light remains lit for as long as
the vehicle is travelling at over 74 mph
(120 km/h).

Driving style indicator 8 ➥ 2.30

 warning light is dis-

12

8

10

9

Total mileage recorder 9 ➥ 1.75

Trip computer 10 ➥ 1.71

Estimated mileage with remaining
fuel 11

The value is displayed after driving
400 metres. ➥ 1.75.

Trip computer and multimedia
information 12

Depending on the vehicle, you can dis­play information from the multimedia
screen (compass, telephone, naviga­tion, etc.) or information from the trip
computer.
Please refer to the multimedia instruc­tions for more information.

7

1.65

DISPLAYS AND INDICATORS (3/7)

14

15

Coolant temperature indicator 14

In normal use, indicator 14 should be
before area 13. Under “intensive” op­erating conditions, the needle may ap­proach this zone. This is not serious

unless the warning light
on accompanied by a message on the
instrument panel and a beep.

1.66

® comes

13

Fuel gauge 15

If the level is at the minimum, warn-

ing light
tor comes on orange, accompanied by
a beep. Fill up as soon as possible.

M integrated in the indica-

DISPLAYS AND INDICATORS (4/7)

B

Instrument panel B

It lights up when the ignition is switched
on. In some cases, the appearance of a
warning light is accompanied by a mes­sage.
Depending on the vehicle, you can cus­tomise your instrument panel with the
content and colours of your choice.
For vehicles fitted with a multimedia
screen, refer to the multimedia instruc­tions.
For vehicles not fitted with a multimedia
screen ➥ 1.83.

17

16

Coolant temperature indicator 16

In normal use, indicator 16 should be
before area 17. Under "intensive" op­erating conditions, the needle may ap­proach this zone. This is not serious

unless the warning light
on accompanied by a message on the
instrument panel and a beep.

Speedometer 18

Depending on the style selected, the
display varies.

® comes

18

19

20

Overspeed buzzer

Depending on the vehicle and coun-

try, the  warning light is dis-

played and a beep sounds. This beep
sounds as soon as the vehicle is trav­elling at over 75 mph (120 km/h). This
warning light remains lit for as long as
the vehicle is travelling at over 74 mph
(120 km/h).

Rev counter 19
(graduations x 1000)

This is displayed differently according
to how the instrument panel is custom­ised. Depending on the style selected,
it may not be displayed.

Driving style indicator 20 ➥ 2.30

1.67

DISPLAYS AND INDICATORS (5/7)

21

24

25

23

Multimedia information 21

Depending on the vehicle, you can dis­play information from the multimedia
screen (the compass, telephone, navi­gation, etc.).
Please refer to the multimedia instruc­tions for more information.

Estimated mileage with remaining
fuel 22

The value is displayed after driving 400
metres. ➥ 1.75.

Total mileage recorder 23 ➥ 1.75

Trip computer 24 ➥ 1.71

1.68

22

Fuel gauge 25

If the level is at the minimum, warn-

ing light
tor comes on orange, accompanied by
a beep. Fill up as soon as possible.

M integrated in the indica-

DISPLAYS AND INDICATORS (6/7)

C

26

29

28

Instrument panel C

It lights up when the ignition is switched
on. In some cases, the appearance of a
warning light is accompanied by a mes­sage.

Depending on the vehicle, you can cus­tomise your instrument panel with col­ours of your choice. For vehicles fitted
with a multimedia screen, refer to the
multimedia instructions.
For vehicle not fitted with a navigation
system ➥ 1.83.

27

Rev counter 26
(graduations x 1000)

Coolant temperature indicator 28

In normal use, the indicator 28 should
be before the red zone 27. Under “in­tensive” operating conditions, the
needle may approach this zone. This
is not serious unless the warning light

® comes on accompanied by a

message on the instrument panel and
a beep.

31

Trip computer 29

➥ 1.71

Estimated mileage with remaining
fuel 30

The value is displayed after driving
400 metres.
➥ 1.75

Total mileage recorder 31

➥ 1.75

30

1.69

DISPLAYS AND INDICATORS (7/7)

32

Driving style indicator 32 ➥ 2.30

33

34

Speedometer 33

Overspeed buzzer

Depending on the vehicle and coun-

try, the
played and a beep sounds. This beep
sounds as soon as the vehicle is trav­elling at over 75 mph (120 km/h). This
warning light remains lit for as long as
the vehicle is travelling at over 74 mph
(120 km/h).

 warning light is dis-

Fuel gauge 34

If the level is at the minimum, warn-

ing light
tor comes on orange, accompanied by
a beep. Fill up as soon as possible.

M integrated in the indica-

1.70

TRIP COMPUTER: general information (1/4)

A

1

4

2

3

Trip computer A, B or C

Depending on the vehicle, this includes
the following functions:

– distance travelled;
– journey settings;
– information messages;
– operating fault messages (con-

nected to the

– warning messages (connected to the

© warning light);

® warning light);

– vehicle settings customisation menu

➥ 1.83.

All these functions are described on the
following pages.

B

1

4

2

3

C

1

4

2

3

1.71

TRIP COMPUTER: general information (2/4)

A

5

8

Vehicle fitted with Ainstrument
panel

The functions will be distributed in
zones 5, 6, 7, and 8. The location of the
zones differs depending on the style
selected.

Press the 1 switch to browse between
areas 5 and 6, then select the functions
by pressing the 2 or 3 switch repeat­edly.

A

1

7

6

2

34

1.72

TRIP COMPUTER: general information (3/4)

B

5

6

8

Vehicle fitted with Binstrument
panel

The functions will be distributed in
zones 5, 6, 7, and 8.

Press switch 1 to browse between the
zones and select the functions by re­peatedly pressing switch 2 or 3.

7

B

1

2

4

3

Vehicle fitted with Cinstrument
panel

Press the switch 1 as many times as re­quired to reach the “Vehicle” tab.

Press repeatedly using control 2 or 3,
then if necessary use switch 4 to con­firm.

C

1

2

4

3

1.73

TRIP COMPUTER: general information (4/4)

Selections

(the display depends on the vehicle
equipment and country)

a) Trip log, operating faults and infor-

mation message readout;

b) Journey settings:
– average fuel consumption;
– current fuel consumption;
– estimated range with remaining fuel;
– distance travelled;
– average speed;
– LPG average fuel consumption;
– estimated range with remaining LPG

fuel;

– LPG range;
c) trip mileage recorder and average

speed;
d) Reset the tyre pressure;
e) set the time;
f) distance before service;
– distance before service;
– mileage before oil change;
g) Estimated range with remaining rea-

gent.

4

Resetting the trip mileage
recorder and journey
parameters (reset button)

With one of the trip parameters se­lected as the display, press and hold
the 4 switch “OK” until the display
resets to zero.

Automatic resetting of the
journey parameters

Resetting occurs automatically when
the maximum value of any of the pa­rameters is exceeded.

Interpreting some of the
values displayed after
resetting

The values showing average fuel con­sumption, range and average speed
will become more stable and reliable
the further you travel after pressing the
reset button.

For the first few miles after pressing
the reset key you will notice that the
range increases as you travel. This
range takes into account the average
fuel consumption since the last time the
reset button was pressed. Therefore,
the average fuel consumption may de­crease when:

– the vehicle stops accelerating;
– the engine reaches its operating

temperature (if the engine was cold
when the reset key was pressed);

– when driving from an urban area

onto the open road.

1.74

TRIP COMPUTER: journey parameters (1/5)

The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.

Examples of selections Interpreting the display selected

a) Trip log.

Vehicle Systems OK

7.4 L/100

5.8 L/100

Successive display:
– information messages (passenger airbag OFF etc.);
– operating fault messages (“Check injection” etc.).

b) Current fuel consumption.

This value is displayed after a speed of approximately 20 mph (30 km/h) is
reached.

Average fuel consumption since the last reset.

The value is displayed after having travelled at least 400 metres since the last
reset.

112,4 km

123.4 km/h

c) Mileage recorder: Distance travelled since the last reset.

Average speed since the last reset.
The value is displayed after driving 400 metres.

1.75

TRIP COMPUTER: journey parameters (2/5)

The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.

Examples of selections Interpreting the display selected

Average LPG

–-.- L/100

Range LPG

–-- km

Distance LPG

–-- km

d) Average LPG fuel consumption.

Estimated range with remaining LPG fuel.

Distance travelled on LPG fuel since the last reset.

55.8 mph (90 km/h)

1.76

e) Current speed (depending on the vehicle).

TRIP COMPUTER: journey parameters (3/5)

The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.

Examples of selections Interpreting the display selected

Tyre pressure init.

long press

16:30

d) Reset the tyre pressure.

➥ 2.40

e) Setting the time.

➥ 1.86

1.77

TRIP COMPUTER: journey parameters (4/5)

The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.

Examples of selections

On-board computer with mileage-

before-service message

f) Mileage before service and oil change.

Service in

30 000 km / 12 months

Service due in

300 km / 24 days

Service Required

Reset: to reset the distance before the next service, press and hold button OK for approximately 10 seconds until the display
shows the mileage before service permanently.

Note: If a service is performed without changing the engine oil, only the mileage before the next service should be reset. In the
event of an oil change, both the distance before the next service and the next oil change should be reset.

Mileage before service
With the ignition on and engine not running, access the “Mileage

before service” information. When the distance value approaches its
limit, there are several possible scenarios:
– If the range is less than 930 miles (1,500 km) or one month: the

message “Service due” is displayed accompanied by the nearest
term (distance or time);

– range equal to 0 miles (0 km) or date of service reached: the mes-

sage “Service Required” is displayed accompanied by the warning
light

The vehicle requires a service as soon as possible.

©.

Interpreting the display selected

1.78

TRIP COMPUTER: journey parameters (5/5)

The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY.

Examples of selections

On-board computer with distance

before next service message (cntd.)

f) Mileage before service or oil change.

Oil change in

30 000 km / 24 months

Depending on the vehicle, the mileage before an oil change varies according to the driving style (frequent driving at low speed,
door-to-door journeys, extensive use at idling speed, towing a trailer, etc.). The distance remaining until the next oil change can
therefore decrease more quickly in some cases than the actual distance travelled.

Reset: to reset the distance before the next service, press and hold button OK for approximately 10 seconds until the display
shows the mileage before oil change permanently.
Note: If a service is performed without changing the engine oil, only the mileage before the next service should be reset. In the
event of an oil change, both the distance before the next service and the next oil change should be reset.

Mileage before service
With the ignition on and the engine not running, access the mileage

information to display the mileage before the next oil change.

Interpreting the display selected

Top Up AdBlue before 2400 km

g) Estimated range with remaining reagent.

1.79

TRIP COMPUTER AND WARNING SYSTEM: information messages

These can help in the vehicle starting phase, or give information about a selection or a driving status.
Examples of information messages are given in the following pages.

Examples of messages Interpreting the display selected

“Parking Brake ON” Indicates that the parking brake has been applied.

“Turn Steering Wheel + START”

“Vehicle Checks in Progress” Displayed with the ignition on when the vehicle is running self-diagnostics.

1.80

Turn the steering wheel slightly whilst pressing the vehicle start button to unlock the steer­ing column.

TRIP COMPUTER AND WARNING SYSTEM: operating fault messages

These appear with the © warning light and mean that you should drive very carefully to an authorised dealer as

soon as possible. If you fail to follow this recommendation, you risk damaging your vehicle.

They disappear when the display selection key is pressed or after several seconds and are stored in the computer log. The

© warning light stays on. Examples of operating fault messages are given in the following pages.

Examples of messages Interpreting the display selected

“Clean Diesel Filter” Indicates the presence of water in the diesel filter; contact an approved Dealer

“Check vehicle” Indicates a fault in one of the pedal sensors, battery management system or oil

“WARNING: Check Airbag” Indicates a fault in the restraint system in addition to the seat belts. In the event

“Check Anti- Pollution System” – Indicates a fault in the vehicle’s particle filter system.

as soon as possible.

level sensor.

of an accident, it is possible that they may not be triggered.

– Indicates a fault in the emissions reduction system when it is accompanied

 warning light. ➥ 1.113.

by the

1.81

TRIP COMPUTER AND WARNING SYSTEM: warning message

These appear with the ® warning light and require you to stop immediately, for your own safety, as soon as traffic

conditions allow. Stop your engine and do not restart it. Contact an approved Dealer.

Examples of warning messages are given in the following pages. Note: the messages appear on the display either individually
or alternately (when there are several messages to be displayed), and may be accompanied by a warning light and/or a beep.

Examples of messages Interpreting the display selected

“WARNING: Engine Failure Risk” Indicates an injection fault, the vehicle’s engine has overheated or there is a

“WARNING: Braking System” Indicates a fault in the braking system.

“WARNING: Electric System” Indicates a fault in the vehicle battery charging circuit (alternator etc.).

“Puncture” Indicates that at least one wheel is punctured or severely underinflated.

“WARNING: Power Steering” Indicates a problem with the steering.

1.82

serious engine fault.

VEHICLE SETTINGS CUSTOMISATION MENU (1/3)

1

Depending on the vehicle equipment,
this function allows you to activate/de­activate and adjust some of the vehi­cle’s functions.

Vehicles fitted with a
multimedia screen 1

Accessing the settings menu

Refer to the various multimedia instruc­tions for information on accessing the
settings.

Adjusting the settings

Select a menu then the function to be
modified (the display depends on the
vehicle equipment and country):

a) “Driving”:
– Indicator volume;
– Free-wheel;

b) “Access”:
– Release driver’s door;
– Lock doors during driving;
– Opening/closing in hands-free

mode;

– Remote locking/Approach un-

locking;
– Distance locking sound;
– Silent mode;
– Automatic locking;

c) “Wiping and lighting”:
– Follow-me-home lighting;
– Wiping in reverse;
– Automatic front wiping;
– Wiping after washing;

d) “Welcome”:
– External welcome;
– Automatic fold-out of mirrors;
– Interior welcome;
– Courtesy light auto mode.

Depending on the function, select:
– “ON” or “OFF” to activate or deacti-

vate,
or
– a duration to adjust the time the lights

are switched on (for the “Follow-me-

home lighting” function for example).
Please refer to the multimedia instruc-

tions for further information.

For safety reasons, carry
out any adjustments when
the vehicle is not being
driven.

1.83

VEHICLE SETTINGS CUSTOMISATION MENU (2/3)

2

3

6

4

5

Vehicles not fitted with a
multimedia screen

Accessing the settings menu on
display 2

With the vehicle stopped, press the 3
switch as many times as required to
reach the “Vehicle” tab; Press repeat­edly on the 4 or 5 switch to access the
“Settings” menu, then confirm by press­ing 6 “OK”.

Adjusting the settings

Navigate using the 4 or 5 control to
select the function to be modified and
press 6 “OK” to confirm (display may
vary according to vehicle equipment
and country):

a) “DASHBOARD”:
– Language;
– Unit;
– Style;
– Colour;

b) “VEHICLE“:
– Rear windscreen wiping in re-

verse gear;
– Automatic windscreen wiping;
– Front/rear drip wiping function;
– Free wheel in ECO mode
– External welcome;
– Free-wheel;

c) “PARKING ASSIST”:
– Beep sound volume;

d) “DRIVING ASSIST”:
– Lane departure warning sound

volume;

– Lane departure warning sensitiv-

ity;
– Lane departure warning vibration;
– Lane keeping assist sensitivity;
– Blind spot warning;
– Active braking;
– Overspeed warning;
– Distance warning;

e) “LIGHTING”:
– Courtesy light auto mode;
– Automatic follow-me-home light-

ing;
– Follow-me-home lighting: XX sec-

onds;
f) “ACCESS”:

– Lock doors during driving;
– Opening/closing in hands-free

mode;
– Unlock the driver’s door only;
– Automatic re-locking;
– Silent locking;
– Automatic opening/closing;
– Automatic fold-out of mirrors;

g) “RESET“.

1.84

= function activated
< function deactivated

VEHICLE SETTINGS CUSTOMISATION MENU (3/3)

To exit the menu, press 4 or 5 to access
“BACK” and confirm by pressing 6
“OK”. It may be necessary to carry out
this operation more than once.

3

6

Once a line has been selected, press 6
“OK” to adjust the function.

If you select either “PARKING ASSIST”
then “VOLUME”, or “DASHBOARD”
then “LANGUAGE”, you will have to
make a further selection (sound volume
of the parking distance control or in­strument panel language). In this case,
make your selection and confirm it by
pressing “6 OK”, the selected value is

shown by a

= in front of the line.

4

5

The vehicle settings personalisation
menu cannot be used when driv­ing. At a speed exceeding 12 mph
(20 km/h), the instrument panel dis­play switches automatically back to
trip computer and warning system
mode.

1.85

CLOCK AND EXTERIOR TEMPERATURE (1/2)

1

6

Vehicles fitted with a multimedia
screen

The time and exterior temperature are
displayed on the multimedia screen 1.

Refer to the multimedia instructions.

1.86

2

5

Vehicles not fitted with a multimedia
screen

Press the switch 2 as many times as re­quired to reach the “Vehicle” tab.

Repeatedly press control 3 or 4 to set
the 6 clock.

Press and hold switch 5 “OK” until the
time display flashes.

3

4

Set the hour using the 3 or 4 control,
then wait for three seconds: the min­utes will flash.

Set the minutes using the 3 or 4 control,
then wait for three seconds: the flash­ing stops and the time setting is com­plete.