Page 1
How to get a great shave
from your Remington
®
MicroScreen®2 Shaver
Thank you for buying this premium
shaver from Remington®.
Inside you'll find tips on using and
caring for your shaver to get the
best shave possible.
Model DA-757
(LCD Display)
Model Only
Model DA-57
(no LED)
Model DA-107
(no LED)
Model DA-307
Model DA-325
Model DA-407
®
IMPORTANT SAFETY
INSTRUCTIONS
When using an electrical shaver, basic precautions
should always be observed, including the following.
Read all instructions before using this shaver.
DANGER
To reduce the risk of electric shock:
■ Do not reach for a shaver that has fallen into
water. Unplug immediately.
■ Do not use while bathing or in a shower.
■ Do not place or store shaver where it can fall
or be pulled into a tub or sink. Do not place
in or drop into water or other liquid.
■ Except when charging, always unplug this
shaver from the electrical outlet immediately
after using.
■ Unplug this shaver before cleaning.
WARNING
To reduce the risk of burns, fire, electric shock,
or injury to persons:
■ A shaver should never be left unattended when
plugged in, except when charging your
rechargeable shaver.
■ Close supervision is necessary when this
shaver is used by, on, or near children or
invalids.
■ Use this shaver only for its intended use as
described in this manual. Do not use attachments not recommended by Remington.
■ Keep the cord away from heated surfaces.
■ Never operate this shaver if it has a damaged
cord or if it is not working properly, if it has
been dropped or damaged, or dropped into
water. Return the shaver to a service center
for examination and repair.
■ Never drop or insert any object into any open-
ing.
■ Do not use outdoors or operate where aerosol
(spray) products are being used or where oxygen is being administered.
■ Do not use this shaver with a damaged or
broken cutter or head, as facial injury may
occur.
■ Always attach plug to shaver, then to outlet.
To disconnect, turn all controls to “Off,” then
remove plug from outlet, then detach power
cord from the shaver for storage.
■ Always store your shaver and cord in a mois-
ture-free area. Make sure your cord is disconnected from the shaver.
■ To prevent possible damage to the cord, do
not wrap cord around the shaver.
■ Never put the shaver in direct sunlight or store
in pouch at a temperature above 140° F.
■ “Household Use Only”.
SAVE THESE
INSTRUCTIONS
Page 2
Getting Used To Your Shaver
Congratulations on your purchase of a premium
R e m i n g t o n®M i c r o S c r e e n®2 Shaver. It will give you
years and years of close, comfortable shaves.
As with every shaver, your shave will improve over
time. So allow about three weeks to develop an
e ffective shaving style and for your skin to adjust to
the new shaver.The adaptation period may take a
little longer if your skin is sensitive, if you are
switching from a different way of shaving, or if you
alternate between shaving methods.
When you first removed your M i c r o S c r e e n®2
Shaver from its box, you may have noticed what
appear to be small particles of white or gray powder on the MicroScreen or in or around the cutter
assembly. The particles are from a coating of a
special lubricant applied to the new foil and cutters to smooth breaking in your new shaver. They
will disappear with use.
The Best Technique
It’s simple to get a great shave out of your new
shaver. Here are a few tips for getting the closest
shave possible:
Always use a clean, dry shaver.
Wait at least 15 minutes after rising
1 2
9 3
to allow the puffiness that most men
experience upon waking to disap-
6
pear.
Make sure your face is clean and dry
before starting.
Hold the shaver so all foils touch your face
together. This allows the shaver to provide for
the closest shave and minimum foil wear. Avoid
holding the shaver at an angle so only one foil
touches the skin. This will distort the foil and may
cause some skin irritation.
Use short, circular strokes
and use your free hand to stretch your skin.
This encourages your whiskers to stand out,
making it easier for them to enter the cutting
mechanism.
Never press hard. Pressing only flattens your
whiskers, which makes it harder for them to
enter the cutting mechanism. It will also wear
out the foils more quickly.
Shaving Longer Hairs
Your MicroScreen®2 Shaver is equipped with
a special push-up trimmer that allows you to
shave stubborn long hairs on facial and neck
areas or trim a beard or mustache quickly and
easily. Just push the trimmer button upward until
the trimmer locks into position. Stroke the hairs
being trimmed lightly. To extend battery life, turn
off the trimmer while you are shaving.
For a Better Shave...
To help maximize your shaver’s performance, consider using
the Remington®Pre-Shave Powder Stick (SP-5). Just rub it
over your beard. It absorbs moisture and facial oils, helping
set up the hairs so they enter the cutting chamber more easily.
It makes shaving quicker and more comfortable.
Cleaning Your Shaver
TO ASSURE SMOOTH, EFFICIENT PERFORMANCE, IT IS IMPORTANT TO CLEAN YOUR
SHAVER. Cleaning your Remington®MicroScreen
2 Shaver is easy.
■ Remove the Head Assembly
by holding onto the sides of the
Head Assembly at the arro w s
and gently lifting the assembly
away from the shaver.
■ Tap the base of the Head
Assembly lightly on a flat surf a c e .
This should dislodge most of the
hairs trapped within it. To guard
against inadvertent damage, do
not remove the Foil Assembly,
except to replace it.
■ Next, clean the Cutter
Assembly while it is still on the
s h a v e r . Hold the shaver and
Cutter Assembly as shown,
and, using the brush supplied,
lightly brush and blow the hair
clippings from between the
b l a d e s .
Ti p : To help reduce wear and tear, spray the foils and
Head Assembly with Remington®Spray Shaver- S a v e r
Lubricant after every shave. This helps remove hairs
while keeping your shaver operating smoothly.
Trimmer Care
The trimmer on your
Shaver is easy to maintain.
■ When you clean your shaver, just brush off any
clippings that may accumulate around the trimmer
Assembly.
Using the longer bristles on the brush supplied will
enable you to get into the area between the trimmer and the shaver.
R e m i n g t o n® MicroScreen®2
®
®
Page 3
■ Every six months, lubricate the trimmer
teeth by applying a drop of light machine
oil one-third and two-thirds of the way along
the blade. Using your finger tip, spread the
oil along the teeth, and run the trimmer for a
few seconds.
Replacing Foils and Cutters
Because they are subject to daily use, the cutters and foils of your
®
R e m i n g t o n
MicroScreen®2 Shaver will wear and eventually re q u i re
replacement to maintain a close, comfortable shave. Depending on your
shaving technique and habits, the foils will usually last six months; the
cutters, one year. Model DA-757 has a foil replacement indicator.
The foil icon on the LCD display will flash when the foil is due for
replacement. Some signs that your foils and cutters need replacing are :
■ Irritation. As foils get worn, you may notice your skin feeling
sensitive after a shave, particularly when you apply aftershave.
■ Pulling. As cutters wear, your shave may not feel as close, and you
may feel your shaver is pulling at your whiskers.
■ Wear-through. You may notice that the cutters have worn through
the foil.
To order replacement foils and cutters, call 1-800-736-4648.
To prevent inadvertent damage to the Foils and Cutter Assembly,
do not attempt to remove them unless you are replacing them. To
remove the old foil and cutters follow the instructions that come with the
foil and cutter replacement package. It's always a good idea to replace
the foils when you replace the Cutter Assembly.
To Replace a Cutter Assembly That is Removed
Unintentionally:
■ Hold the assembly in the middle of the "T."
■ Gently place the forked legs into the open-
ing at the top of the oscillator tips.
■ Do not push downward on the ends of the
cutters, as you may bend the cutter, reducing
its ability to operate smoothly.
■ Do not remove cutters from the plastic
pieces to which they are attached, as you may
damage the assembly.
Removing the Headguard
Before operating your
MicroScreen®2 Shaver, remove
the Headguard, which protects
the Foils and Cutter Assembly.
It is important to remove the
Headguard correctly to avoid
damaging the clips that hold
■ Press lightly on the top of the Headguard.
■ Lift the lower rear edge.
■ Pull the Headguard away from the shaver.
it firmly to the shaver.
Operation
Use of a shaver at voltages other than the ones
specified below will damage it and void the warranty.
Model DA-57, DA-107 - Corded Shavers 120 Volts A.C.
Model DA-307, DA-325 - Rechargeable Shaver
World-wide A.C.voltage:105-130 Volts A.C.
at 60 Hz,and 105-240 Volts,A.C. at 50 Hz.
Model DA-407 - Cord/Cordless Shaver World-wide A.C.
voltage:100-240 Volts A.C.,50-60 Hz.
Model DA-757 - Cord/Cordless Shaver With LCD Display
World-wide A.C.voltage:100-240 Volts A.C.,50-60 Hz.
Charging
Charge your shaver 24 hours before initial use.
Make sure the ON/OFF button is set to OFF (with
“O” visible). Connect the cord to the shaver and then
to the electric outlet.
Model DA-307, DA-325,and DA-407 The Green indicator
light will glow indicating that the shaver is charging.
The shaver will be completely re c h a r ged in 14-16 hours.
The red indicator light in the DA-325 model will glow
when the shaver needs to be re c h a rg e d .
Model DA-757 This shaver has an LCD display. The bars
on the display give the % of battery power left in your
shaver. The plug icon will flash when your shaver needs
to be recharged. There is also a foil replacement indicator. The foil icon on the display will flash when the foil is
due for replacement. The one hour quick charge feature in this model gives up to 60 minutes of cordless
shaving time. A 5 minute quick charge gives enough
shaving time for one shave
To Shave
Model DA-57,and DA-107
to electric outlet.Slide the ON/OFF button upward to turn ON
Connect cord to shaver and then
.
Model DA-307 and DA-325 With the shaver unplugged,press in on the
Switch Lock and slide the ON/OFF button upward to turn ON.Note that this
shaver is designed only to operate from its batteries; it must be charged
before using.
Model DA-407,and DA-757 These shavers can be powered from either
the cord or the battery. To shave using the battery, make sure that the
shaver has been charged. To shave using the cord,connect cord to shaver
and then to electric outlet.Press in on the Switch Lock and slide the ON/OFF
button upward to turn ON.
Trouble Shooting
■
If your DA-407,757 shaver bat t e ry is completely discharged or the shaver has
not been used for an extended period of time, the shaver may not start when operated using the cord. If this condition occurs,charge the shaver for ap p r o x i m at e ly
five minutes before shav i n g .
■
Your DA-407, 757 cord/cordless shaver should not be used strictly as a cordo p e r ated shav e r,as continued cord only use will result in reduction of bat t e ry life.
■
In order to preserve the life of the bat t e r i e s ,t h ey should be fully discharged every
six months and then fully charged for 24 hours.
Battery Removal
(Cord/Cordless and Cordless
Rechargeable Models Only)
When your rechargeable shav e r
reaches the end of its useful life, t h e
b atteries must be removed from the shaver and be recy cled
or disposed of properly in accordance with your local and stat e
r e q u i r e m e n t s .
The following procedure should be followed
for battery removal:
• To avoid a possible electrical shock hazard,unplug cord
from electrical outlet and shaver.
• Remove the head assembly by pushing in on the
head assembly release buttons.
• Remove the two screws on the upper back side of the
shaver.
• Pull or pry the shaver halves apart.
• Pull out the motor and frame assembl y.
• Pull or pry the batteries outward from the shaver’s
circuit board.
• Pull and twist the batteries to break the wire connections.
• CAUTION:Do not put in fire or mutilate your batteries when
disposing as they may burst or release toxic materials.Do
not short circuit as it may cause burns.Dispose of properly
in accordance with your local and state requirements.
CAUTION: THESE NICKEL-CADMIUM BATTERIES MUST BE RECYCLED OR DISPOSED IN
A C C O R DANCE WITH STATE AND LOCAL REGULAT I O N S . Do not burn or mutilat e , as they
m ay burst or release toxic mat e r i a l s .Do not short-circuit, as it may cause burns.
Page 4
Headguard
Dual Flexible
Head
Assembly
Head
Assembly
Release
Button
(Both sides)
Charging
Indicator
Light
(DA-307,
DA-325,
DA-407)
Low Battery
Indicator Light
(not shown)(DA-325)
Cord Inlet
MicroScreen®Foil
ON/OFF Switch Lock
(DA-307, DA-325,
DA-407)
ON/OFF Switch
Easy-View Trimmer
Rear of Shaver
Remington MicroScreen®2 Models
Which model is yours?
DA-57,
DA-107
DA-307,
DA-325
DA-407
DA-757
Corded Shavers,
120 Volts A.C.
Rechargeable Shaver - World-wide A.C.
105-130 Volts A.C. at 60 Hz ,and 105-240 Volts,
A.C. at 50 Hz.
Cord/Cordless Shaver - World-wide A.C.
voltage:100-240 Volts A.C.,50-60 Hz
Cord/Cordless Shaver with LCD Display
World-wide A.C.voltage:100-240 Volts A.C.,
50-60 Hz
Foil
Gauge
DA-757
Remington®Money-Back Offer
You have just bought one of the finest
shavers available today. If for any reason
within 30 days from when you purchased
your Remington®MicroScreen®2 Shaver,
you are not satisfied and would like a
refund, just return your shaver, together
with the sales receipt, to the retailer from
whom you purchased it. Remington will
reimburse all retailers who accept shavers
within 30 days of purchase. If you have
any questions regarding this money-back
guarantee, please call 1-800-736-4648.
Full One-Year Warranty
Remington warrants that your product, except as noted below, i s ,
on date of purchase, free from defect in material and workmanship.
Remington will correct any such defect without charge if you return
the complete product either in person or by mail, p o s t age paid, to a
Remington Company - owned Service Center or Authorized Serv i c e
Dealer within one year after date of purchase.
Do not return the product to the retailer from whom the product
was purchased.
This warranty does not cover damage by accident, m i s u s e , abuse or
by affixing an unauthorized accessory or alteration to the product, o r
by connection of the product to any but the specific current and voltage indicated in an accompanying instruction booklet, or by any
other conditions beyond our control. REMINGTON SHALL NOT BE
RESPONSIBLE FOR ANY INCIDENTA L ,SPECIAL OR CONSEQUENTIAL
D A M A G E S .
IN A D D I T I O N ,THIS WARRANTY DOES NOT COVER THE FLEXIBLE
SCREEN A S S E M B L Y ON OUR FOIL TYPE SHAV E R S .
ALL IMPLIED WARRANTIES INCLUDING BUT NOT LIMITED TO IMPLIED
WARRANTIES OF FITNESS AND MERCHANTA B I L I T Y, ARE LIMITED IN
D U R ATION TO ONE YEAR FROM DATE OF ORIGINAL PURCHASE.
This warranty gives you specific legal rights, and you may also hav e
other rights that vary from state to stat e . Some states do not allow
the exclusion limitation of incidental or consequential damages or
l i m i t ations on how long an implied warranty lasts, so that the above
l i m i t ations and exclusions may not apply to you.
No responsibility, o b l i g at i o n , or liability is assumed for the installat i o n
or maintenance of this product.
Warranty service must be performed by a Remington Company owned Service Center or Authorized Service Dealer and damage or
loss of any kind resulting from servicing by any other person is not
covered under warranty. E n closed is a listing of Company - ow n e d
S e rvice Centers. Authorized Service Center Dealers may be found
in the yellow pages of your directory. If you wish,you may mail
the product, p o s t p a i d , to Remington Products Company, 60 Main
S t r e e t ,B r i d g e p o r t , CT 06604 A t t e n t i o n :S e rvice Department.
U.S. Warranty Service
In the United States, service is pro v i d e d
by our Company-owned Service Centers
and over 300 Authorized Service Dealers.
The addresses of our Company-owned
S e rvice Centers are enclosed. For the
a d d ress of your nearest Authorized Serv i c e
D e a l e r, please consult the Yellow Pages
under “Shaver - Electric - Repair.” If you
wish, you may mail the product, postpaid,
to Remington Products Company, 60 Main
S t reet, Bridgeport, CT 06604, Attention:
S e rvice Depart m e n t .
International Warranty Service
S e rvice under the Remington warranty can
be obtained outside the United States by
Remington-Authorized Distributors and
S e rvice Dealers. Please consult your local
telephone dire c t o ry for the nearest location.
For questions or comments, please write:
Z
P RO D UC T S C O MP A N Y, L .L . C .
60 Main Street Bridgeport, CT 06604
U.S. Patent Design #362, 739
Canadian Design Patent 77, 681
Remington Products Company, L . L . C .
P. O . Box 1536,
H o r s h a m , PA 19044-6536
A t t e n t i o n : Consumer A f f a i r s
Questions or Comments: Please call 1-800-736-4648.
Visit us at http:\\www. r e m i n g t o n - p r o d u c t s . c o m
R e m i n g t o n , MicroScreen and
S h av e r S aver are trademarks of
Remington Corporat i o n ,L . L . C .
© 1999 RPC,L . L . C .R e v. 3 / 9 9
Part No. 1 2 5 5 4
Loading...