Regency Classic I1200 Installation Manual
www.regency-fi re.com
Owners & Installation Manual
I1200S
Wood Insert
Tested by:
918-665a
Installer: Please complete the details on the back cover
and leave this manual with the homeowner.
Homeowner: Please keep these instructions for future reference.
FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4
01/0510
WARNING
HOT GLASS
CAUSE BURNS
DO NOT TOUCH
UNTIL COOLED
NEVER
TO TOUCH GLASS
CHILDREN AND ADULTS SHOULD BE ALERTED TO
THE HAZARDS OF HIGH SURFACE TEMPERATURES,
ESPECIALLY THE FIREPLACE GLASS, AND SHOULD
ST AY AWA Y TO AVOID BURNS OR CLOTHING IGNITION.
ALLOW CHILDREN
WILL
GLASS
Thank-you for purchasing a
REGENCY FIREPLACE PRODUCT.
The pride of workmanship that goes into each of our products will give you years of trouble-free
enjoyment. Should you have any questions about your product that are not covered in this manual,
please contact the REGENCY DEALER in your area.
Keep those REGENCY FIRES burning.
SAFETY NOTE: If this Insert is not properly installed, a house fi re may result. For your safety,
follow the installation instructions, contact local building or fi re offi cials about restrictions and
installation inspection requirements in your area.
The authority having jurisdiction (such as municipal building department, fi re department,
fi re prevention bureau, etc.) should be consulted before installation to determine the need
to obtain a permit.
I1200 Regency Wood Insert2
TABLE OF CONTENTS
SAFETY LABEL
Safety Label...................................................................4
UNIT DIMENSIONS
With Standard Flue Adaptor ..........................................5
With Offset Flue Adaptor ...............................................6
INSTALLATION
Before Installing your Insert ...........................................7
Chimney Specifi cations .................................................7
Fireplace Specifi cations.................................................7
Masonry and Factory Built Fireplace Clearances .........8
How to Determine if Alternate ..........................................
Floor Protection Materials are Acceptable .....................8
Installing your Insert ......................................................9
Installation into a Masonry Fireplace ...........................10
Installation into a Factory Built Fireplace .....................10
Faceplate, Trim & Optional Fan Support Installation ...11
Fan / Blower ................................................................15
Firebrick Assembly ......................................................16
Draft Control ................................................................16
Door Handle ................................................................16
Brick Flue Baffl e & Secondary Air Tube Installation ....16
Screen Door ................................................................17
OPERATING INSTRUCTIONS
First Fire ......................................................................17
Fan Operation..............................................................18
Ash Disposal................................................................18
Some Safety Guidelines ..............................................18
MAINTENANCE
Creosote ......................................................................18
Maintenance of Gold-Plated Doors .............................19
Door Gasket ................................................................19
Door Latch Adjustment ................................................19
Glass Cleaning ............................................................19
Glass Replacement .....................................................19
Glass Removal ............................................................19
PARTS LIST
Main Assembly ............................................................20
Faceplates ...................................................................21
Firebrick .......................................................................22
WARRANTY
Warranty ......................................................................23
I1200 Regency Wood Insert 3
SAFETY LABEL
LISTED FACTORY BUILT FIREPLACE INSERT
CERTIFIED FOR USE IN CANADA AND U.S.A.
MODEL:
I1200S
TESTED TO:
ULC S628-M93 / UL 1482-1998 / ULC S627-00 / UL 737-2000 REPORT NO. 632-3198 (SEPT.1993)
DO NOT REMOVE THIS LABEL
326
COMPONENTS REQUIRED FOR INSTALLATION: 6IN / 150MM STAINLESS STEEL LINER. STANDARD ADAPTOR (171-932) OR OFFSET
ADAPTOR (171-936)
OPTIONAL COMPONENT: FAN (170-915), ELECTRICAL RATING: VOLTS 115, 60 HZ, 0.6 AMPS, SCREEN DOOR (846-101)
DO NOT REMOVE BRICKS OR MORTAR IN MASONRY FIREPLACE. FOR USE WITH SOLID WOOD FUEL ONLY. DO NOT USE GRATE
OR ELEVATE FIRE. BUILD WOOD FIRE DIRECTLY ON HEARTH. OPERATE WITH FEED DOOR CLOSED, OPEN TO FEED FIRE ONLY.
REPLACE GLASS ONLY WITH CERAMIC GLASS (5MM). INSPECT AND CLEAN CHIMNEY FREQUENTLY. UNDER CERTAIN CONDITIONS
OF USE CREOSOTE BUILDUP MAY OCCUR RAPIDLY. DO NOT OVERFIRE, IF INSERT GLOWS YOU ARE OVER-FIRING.
MINIMUM CLEARANCES TO COMBUSTIBLE MATERIALS (MEASURED FROM INSERT BODY)
INSTALL ONLY ON A NON-COMBUSTIBLE HEARTH RAISED (F) 1.5IN / 38MM
ABOVE AN ADJACENT COMBUSTIBLE FLOOR. COMBUSTIBLE FLOOR
MUST BE PROTECTED BY NON-COMBUSTIBLE MATERIAL EXTENDING
(E) 16 IN / 405MM TO FRONT AND (G) 8IN / 205MM TO SIDES FROM FUEL
DOOR.
918-666
MANUFACTURED BY:
FPI FIREPLACE PRODUCTS
INTERNATIONAL LTD.
6988 VENTURE ST.
DELTA, BC V4G 1H4
HOT WHILE IN OPERATION
DO NOT TOUCH. KEEP CHILDREN,
CLOTHING AND FURNITURE AWAY.
CONTACT MAY CAUSE SKIN BURNS.
READ ABOVE INSTRUCTIONS.
CAUTION
ADJACENT SIDEWALL A) 15in / 380mm
MANTLE B) 20in / 510mm
TOP FACING C 14in / 355 mm
SIDE FACING D) 7.375in / 185mm
INSTALL AND USE ONLY IN ACCORDANCE WITH THE MANUFACTURER'S INSTALLATION AND OPERATING INSTRUCTIONS. INSTALL AND USE ONLY
IN MASONRY FIREPLACE OR FACTORY BUILT FIREPLACE.
CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUT RESTRICTIONS AND INSTALLATION INSPECTION IN YOUR AREA.
UNITED STATES ENVIRONMENTAL PROTECTION
AGENCY CERTIFIED TO COMPLY WITH JULY 1990,
PARTICULATE EMISSION STANDARDS.
JAN FEB MAR APR MAY JUN JUL AUG SEPT OCT NOV DEC
2009 2010 2011
(Duplicate Serial #)
DATE OF MANUFACTURE
MADE IN CANADA
326
This is a copy of the label that accompanies each
I1200S Wood Insert. We have printed a copy
of the contents here for your review.
NOTE: Regency units are constantly being
improved. Check the label on the unit and if
there is a difference, the label on the unit is
the correct one.
I1200 Regency Wood Insert4
UNIT DIMENSIONS
WITH STANDARD FLUE ADAPTOR
STANDARD FLUE ADAPTOR (171-932)
6" (152mm) Diameter
I1200 Regency Wood Insert 5
UNIT DIMENSIONS
te
WITH OFFSET FLUE ADAPTOR
21-1/4” (540mm)
6" (152mm) Diameter
OFFSET FLUE ADAPTOR (171-936)
12-3/4” from flue centerline to rear of facepla
22-3/4” (578mm)
22-3/4” (578mm)
16-7/8” (428mm)
20-1/8” (511mm)
16-15/16” (430mm)
14-3/16” (360mm)
12-3/4” (324mm)
18-3/4” (476mm)
19-1/2” (496mm)
21-3/8” (543mm)
17-3/4” (451mm)
22-3/4” (578mm)
I1200 Regency Wood Insert6
INSTALLATION
Regency Inserts are constructed with the highest quality materials and assembled under strict
quality control procedures that ensure years of
trouble free and reliable performance.
It is important that you read this manual thoroughly and fully understand the installation and
operating procedures. Failure to follow instructions may result in property damage, bodily injury
or even death. The more you understand the
way your Regency Insert operates, the more
enjoyment you will experience from knowing that
your unit is operating at peak performance.
BEFORE INSTALLING
YOUR INSERT
1) Read all instructions before installing and
using your fi replace insert. Install and use
only in accordance with manufacturer’s
installation and operating instructions.
2) Check your local building codes - Build-
ing Inspection Department. You may
require a permit before installing your
insert. Be aware that local codes and
regulations may override some items in
the manual.
WARNING: Careless installation is the
major cause of safety hazard. Check all
local building and safety codes before
installation of unit.
3) Notify your home insurance company that
you plan to install a fi replace insert.
4) Your fi replace insert is heavy and requires
two or more people to move it safely. The
insert and surrounding structure can be
badly damaged by mishandling.
5) If your existing fi replace damper control
will become inaccessible once you have
installed your Regency Insert, you should
either remove or secure it in the open position.
6) Inspect your fi replace and chimney prior
to installing your insert to determine that it
is free from cracks, loose mortar or other
signs of damage. If repairs are required,
they should be completed before installing
your insert. Do not remove bricks or mortar
from your masonry fi replace.
7) Do not connect the insert to a chimney
fl ue servicing another appliance or an air
distribution duct.
CHIMNEY
SPECIFICATIONS
Before installing, check and clean your chimney
system thoroughly. If in doubt about its condition, seek professional advice. Your Regency
Insert is designed for installation into a masonry
fi replace that is constructed in accordance with
the requirements of "The Standard for Chimneys,
Fireplaces, Vents, and Solid Fuel Burning Appliance", N.F.P.A. 211, the National Building
Code of Canada, or the applicable local code
requirements.
The appliance, when installed, must be electrically grounded in accordance with local codes or,
in the absence of local codes, with the National
Electrical Code, ANSI/NFP A 70, or the Canadian
Electrical code, CSA C22.1.
Regency Inserts are designed with a 6" (152mm)
fl ue.
This insert must be connected to a code-approved masonry chimney or listed factory-built
fi replace chimney with a direct fl ue connector
into the fi rst chimney liner section. The chimney
size should not be less than or more than three
times greater than the cross-sectional area of
the fl ue collar.
Requirements for Installing
Solid-fuel Inserts in Factory-built
Fireplaces.
1) The insert must be tested and meet the
requirements of UL 1482 (U.S.) and or ULC
S628 (Canada) when tested in a masonry
fi replace built per ULC S628.
2) The factory-built fi replace must be listed per
UL 127 or ULC S610.
3) Clearances obtained from the masonry fi re-
place tests are also relevant for installation
in factory-built fi replaces.
4) Installation must include a full height listed
chimney liner type HT requirements (2100
degree F.) per UL 1777 (U.S.) or ULC
S635 (Canada). The liner must be securely
attached to the insert fl ue collar and the
chimney top.
5) Means must be provided to prevent room
air passage to the chimney cavity of the
fi replace. This may be accomplished by
sealing the damper area around the chimney
liner, or sealing the fi replace front.
6) Alteration of the fi replace in any manner is not
permitted with the following exceptions;
a. external trim pieces which do not affect
the operation of the fi replace may be
removed providing they can be stored
on or within the fi replace for re-assembly
if the insert is removed.
b. the chimney damper may be removed
to install the chimney liner.
7) Circulating air chambers (i.e. in a steel
fi replace liner or metal heat circulator) shall
not be blocked.
8) Means must be provided for removal of the
insert to clean the chimney fl ue.
9) Inserts that project in front of the fi replace
must be supplied with appropriate supporting
means.
10) Installer must mechanically attach the supplied label to the inside of the fi rebox of the
fi replace into which the insert is installed.
"WARNING: This fi replace has been converted
for use with a wood insert only and cannot be
used for burning wood or solid fuels unless
all original parts have been replaced, and the
fi replace re-approved by the authority having
jurisdiction."
FIREPLACE
SPECIFICATIONS
Your fi replace opening requires the following
minimum sizes:
Height: 19" (483mm)
Width: 23" (584mm)
Depth:
(w/ standard fl ue adaptor) 13-3/4" (349mm)
(w/ offset fl ue adaptor) 16-1/2" (419mm)
Two faceplates are available to seal the
fi replace opening:
Standard 38" W x 26" H
Oversize 44" W x 30" H
Emissions from burning wood or gas could
contain chemicals known to the State of California to cause cancer, birth defects or other
reproductive harm.
I1200 Regency Wood Insert 7
Loading...