Page 1
SMARTPILOT SURFACE MOUNT
CONTROLLER INSTALLATION GUIDE
Parts supplied
ST6002 ST7002 or ST8002
Gasket
Site requirements
www.raymarine.com
Check
Gasket
Sun Cover
Tools required
Power Drill
SmartPilot ST6002
Controller
and / or
SeaTalk Cables
Measure
Pencil
Sun Cover
Stud
(x2 ST6002)
(x4 ST7/8002)
3
5mm (
90 mm (3½ in) Hole Cutter
SmartPilot Controller
(ST8002 shown)
Screw
(x2 ST6002)
(x4 ST7/8002)
Connector (x2)
in) Drill
/
16
Check
Min 0.8m (2ft 6in)
D6354-2
Raymarine Ltd, Portsmouth, Hampshire, UK PO3 5TD
Raymarine Inc. Merrimack, NH, 03054-4801, US
Recyclable Material - Please dispose of responsibly.
ST6002 surface mount template
SURFACE MOUNT
Template
Cut hole
3.54 in (90 mm)
diameter
TOP
+44 (0) 23 9269 3611
Toll Free: 800-539-5539
+1 603-881-5200
Drill hole, 3/16 in (5 mm)
diameter in 2 positions
87058-1
1.77 in (45.0 mm)1.76 in (44.6 mm)
Check
ST6002 controller - Step 1
SURFACE MOUNT
Template
from shaded areas only
Instrument edge
1.185 in (30.1 mm)
TOP
Drill hole, 3/16 in (5 mm)
Cut hole
3.54 in (90 mm
diam
eter
)
Remove material
1.18 in (30.0
diameter in 2 positions
mm)
Sun cover edge
D6355-1
1.77 in (45.0 mm)1.76 in (44.6 mm)
Instrument edge
Remove material
from shaded areas only
1.185 in (30.1 mm) 1.18 in (30.0 mm)
Sun cover edge
D8157-2
D6360-2
SURFACE MOUNT
Template
from shaded areas only
Instrument edge
1.185 in (30.1 mm)
TOP
Drill hole,
Cut hole
3.54 in (90 m
diameter
m
)
Remove material
1.18 in (30.0 mm)
diameter in 2 positions
3/16 in (5
mm)
Sun cover edge
1.77 in (45.0 mm)1.76 in (44.6 mm)
D6356-2
Page 2
ST7002 and ST8002 controller - Step 1
ST6002 - Step 2
Sticky side
TOP
Machine hole
90 mm (3.55 in)
Remove m
Remove material from shaded
diameter
aterial from shaded
TOP
Machine hole
90 mm (3.55 in)
diameter
Control Unit
SURFACE MOUNT
Template ST7002 & ST8002
areas only
Control Unit
SURFACE MOUNT
Template ST7002 & ST8002
Drill 5 mm (3/16 in)
diameter hole
(4 positions)
Instrument
edge
Sun cover
edge
ST7002 and ST8002 - Step 2
Sticky side
ST6002 - Step 3
areas only
Drill 5 mm (3/16 in)
diameter hole
(4 positions)
Instrument
edge
Sun cover
edge
D6357-2
D6358-2
ST7002 and ST8002 surface mount template
Remove material from shaded areas only
ST7002 and ST8002 - Step 3
D6359-2
Sun cover
edge
Instrument
edge
90 mm (3.55 in)
Machine hole
diameter
Drill 5 mm (3/16 in)
diameter hole
(4 positions)
TOP
Control Unit
SURFACE MOUNT
Template ST7002 & ST8002
?
Refer to Autopilot Manual
Référer le manuel de pilote automatique
Siehe Autopiloten Handbuch
Refiérase al manual del piloto
Refiérase a manual de autopilot
SmartPilot
System
Commissioning
your SmartPilot
D6361-2
Loading...