Raymarine E03017, E03016 User Manual

Introduction

Your Raymarine CAM
50 CCTV camera is a
good quality color
camera available in two
models:

•E03016 - NTSC
format.

•E03017 - PAL format.

It is waterproof to IP63 standard and suitable
for use in indoor locations such as the wheel
house, salon or engine room.

Safety notices

CAUTION: Power supply

The CAM 50 CCTV camera is suit­able for use on a 12 V DC power
supply only.

CAUTION: Power supply

A 0.5 A quick-blow fuse should be
fitted to the positive (red) lead of the
camera.

CAUTION: Installation

This product IS NOT suitable for
installation underwater.

This product contains no user
serviceable parts.

Installation

What’s in the box?

12V DC

ONLY

What tools are required?

Drill bit

Drill

What accessories are
available?

To enable you to complete the cabling to instal
your camera the following are available:

• E06017 - 5 m extension cable.

• E06018 - 15 m extension cable
The cables can be joined in any combination to

achieve the required cable length.

Cable runs

You need to consider the following points
before installing your camera cables:

• You need to connect the camera to a
display unit and power supply.

• All cables should be adequately clamped
and protected from physical damage and
exposure to heat - avoid running cables
through bilges or doorways, or close to
moving or hot objects.

Phillips
screwdriver

• Acute bends must be avoided.

• Where a cable passes through an exposed
bulkhead or deckhead, a watertight gland
or swan neck tube should be used.

• CCTV camera cables cannot be cut and
rejoined.

Installation

Having selected a suitable installation site:

1.Remove the
camera dome by
gently turning it
counter- clockwise
to release the
bayonet fixing.

2.Remove the
camera cover by
gently pulling it

Camera

Dome

Cover

cable slot of the camera baseplate to
ensure that it is not pinched when the
baseplate is secured in position.

With the camera installed you can now adjust
the field of vision .

away from the
dome baseplate.

3.Hold the base­plate in the
required position
and using a
pencil mark the
fixing holes.

4. Using a suitable
drill bit make pilot
holes for the fixing
screws.

5.Fix the camera
and baseplate into
position using the
two screws
provided.

6.Make sure that
the cable is
placed in the

A

B

You cabn adjust both the pan and the tilt of the
camera.

To adjust the pan of the camera:

1. Loosen screw A.

2. Gently turn the camera assembly until the
lens is pointing in the required direction.

3. Gently pinch screw A to secure the camera
in position.

To adjust the tilt of the camera:

1. Loosen screw B.

2. Holding the edges of the camera plate
gently tilt the camera up or down into the
required position.

3. Gently pinch screw B to secure the camera
in position.

You should now connect the camera to your
display and check that the required image is
being shown.

Either adjust the image by changing the pan
and tilt as detailed above, or, replace the
camera dome and cover to complete the
installation.

Cable connections

The extension cables from

Female

Male

be used to connect the display and the power
supply to the camera. The adapter cable
connections are shown below.

the camera to the display
unit are joined using the
male/female twist
connectors.

The adapter cable should

Video connector

Red +12 V
Black - 0 V

D8537_1

If you do not have a breaker in the power
circuit, an in-line 0.5 A quick blow fuse should
be fitted to the positive (red) lead of the cable.

Maintenance and
Troubleshooting

Your Raymarine CAM 100 does not contain
user-serviceable parts. They should be
serviced only by authorized Raymarine service
technicians at a Raymarine factory facility.

Routine Maintenance

Routine maintenance should be carried out on
a regular basis:

• Examine all cables for signs of damage
such as chafing, cuts or nicks.

• Check that all cables are securely
connected.

• Spray the camera and lens with fresh water
and wipe with a soft lint-free cloth to
remove debris or salt deposits.

Troubleshooting

Problem Solution

Camera does not
function

1. Make sure that the cable is
sound and that all connec­tions are tight and free from
corrosion.

2. Check system fuses.

3. Check that the display is set up
correctly to receive the

images.

Refer to the relevant display
handbook for full details.

Format NTSC 512 x 492 pixels

Imager 1/3 Sony DSP Color CCD

Horizontal resolution 380TVL

Scanning system NTSC 525 lines 2:1 interlaced

Video output Composite 75 Ohms

Shutter speed NTSC 1/60 - 1/100.000sec

Minimum illumina­tion

Waterproof IP63

Power connection 12 V tinned leads

Video connections Female BNC

Operating tempera­tures

Power consumption 80 mA with regulated power

Lens 3.6 mm

PAL 500x 582 pixels

PAL 625 lines

PAL - 1/50 - 1/100.000 sec

0.3 Lux at F2

o

C to +50o C (-14o F to 122o F)

-10

input.

Best focus - 1.5 m
Viewable distance - 3.5 m

Waste Electrical and Electronic
Equipment (WEEE) Directive

Raymarine fully complies with the
WEEE directive and as part of its envi­ronmental policy asks you to b e aware

of how you should dispose of this
product properly. The crossed out wheelie bin,
illustrated on the left, and found on our prod­ucts signifies that this product should not be
disposed of in general waste or landfill. Please
contact your local dealer, national distributor or
Raymarine Technical Services for information
on product disposal.

Technical SupportTechnical SpecificationMaintenance

Restriction of the use of certain
Hazardous Substances

This product uses components

RoHS

COMPLIANT

(RoHS) Directive 2002/95/EC.

Warranty

To register your new Raymarine product,
please take a few minutes to visit our website
www.raymarine.com. It is important that
you register to receive full warranty benefits.

Technical support

Complete product information and interactive
help is available at:

North and South America

Raymarine Technical Support

[phone] or, [phone]

Product Repair and Service

Raymarine Product Repair Center
21Manchester Street, Merrimack,NH0354-

4801

Europe, Middle East, Africa and
Australasia

Raymarine Technical Support

[phone]

Product Repair and Service

Raymarine plc, Anchorage Park, Portsmouth,
PO3 5TD, England.

that comply with the requirements
of the Restriction of the use of
certain Hazardous Substances

www.raymarine.com

Document No:8129 4_1 Date: December 2006

CAM 50

User Guide