This device complies with part 15 of the FCC rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and may cause harmful
interference to radio communications if not installed and used in
accordance with the instructions. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment o and on, the user is
encouraged to try to correct the interference by one of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
IC Compliance Statement
This device complies with Part 15 of the FCC Rules and Industry Canada
license-exempt RSS standard(s). Operation is subject to the following
two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference
that may cause undesired operation of the device.
This Class B digital apparatus complies with Canadian ICES-003.
IC Caution
Intentional or unintentional changes or modications to the equipment not
expressly approved by Rand McNally could void the user’s authority
to operate the equipment.
IC attestation de conformité
Ce dispositif est conforme à la norme FCC Partie 15 et aux norme(s)
RSS permis-exempte(s) d’Industrie Canada. L’opération est soumise
aux deux conditions suivantes:
• Connect the equipment into an outlet that is on a dierent circuit
from the GPS unit.
• Consult the dealer or an experienced radio/TV technician for help.
3. Ce dispositif ne peut pas provoquer d’interférence nocive et
4. Ce dispositif doit accepter toute interference reçue, y compris
les interférences qui peuvent causer un mauvais fonctionnement
du dispositif.
When using the device, ensure that the antenna of the device is at least 20
cm away from all persons.
Cet appareil numérique de la classe B est conforme à la norme
NMB-003 du Canada.
Attention
Les changements ou modications à l’équipement, que ce soient
intentionnelles ou non, non expressément approuvés par Rand McNally
pourraient annuler l’autorisation de l’utilisateur à utiliser cet équipement.
IC: 10199A-01001A
TND™ User Manuali
About GPS
The Global Positioning System (GPS) is a constellation of satellites that
a GPS receiver uses to calculate geographical positions. To determine
a position, data from at least three satellites is required. To determine
elevation, the data from four or more satellites is required. Accuracy of
the positioning varies from 10 feet to several hundred feet, depending
on vehicle placement and the surrounding environment.
Geographical terrain (such as mountains), man-made structures (such as
highway overpasses, bridges, and tall buildings), as well as weather
can interfere with the GPS signal. For best GPS reception, position the
device and mount with a clear line of sight to the sky. Some vehicles
may have a limited view of the sky due to metal sun shields or a
metallized windshield coating.
Map data includes the geographical coordinates for address locations and
points of interest (POIs). With GPS reception, your device calculates a route
to your selected location.
Customer Support
Call toll-free:
1-877-446-4863
Service hours:
Monday through Friday, 7 a.m. to 6 p.m. CT
(Except ocial holidays)
E-mail:
TNDSupport@randmcnally.com
TND™ User Manualii
Table of Contents
1. Your Device ....................................................................................................................... 1
Safety Information ..........................................................................................................1
What’s Included ........................................................................................................... 2
Charge the Battery ...................................................................................................... 2
Install the Mount ............................................................................................................. 2
More Information ........................................................................................................65
TND™ User Manualiii
1. Your Device
Caution: Important Safety Information
Navigation
• Use this navigation device at your own risk.
• Use this navigation device only when it is safe to do so.
• Look at the display only when it is safe to do so.
• Trac regulations always have priority over any instructions from the
navigation system.
• Follow navigation system instructions only when local regulations and
road trac allow you do so.
• Make sure that the mount is securely mounted and properly
adjusted before each trip.
• Note: If you do not understand the spoken instructions or are unsure
of what to do next, refer to the navigation map on your navigation
device.
Installation
• Make sure that the mount does not impair the driver’s visibility.
Device
• Do not use sharp-edged objects on the device touch screen.
• The device is not waterproof and is not protected against water damage.
• Protect the device from extreme temperatures. Operating
temperature for the device is between 32 degrees F and
120 degrees F.
• Do not open the navigation device casing.
• Do not attempt to replace the battery. Contact Rand McNally
Customer Support with questions about the battery.
• Always follow local regulations when disposing of this device.
• Note: Make sure that there are no kinks in the cable and that
it will not be damaged by any sharp objects.
• Note: Use only a moist cloth to clean the navigation device.
• Note: Do not pull the cable to unplug the unit.
• Do not attach the mount within the airbag deployment zone.
• When installing the mount, make sure that it does not pose a risk
in the event of an accident.
• Do not run cables directly next to safety-relevant devices and
power supplies.
• After installation, check all safety-relevant equipment.
• Connect the wall charger to a 120V or 240V outlet only.
• Connect the vehicle charger to a 12V outlet only.
TND™ User Manual1
1. Your Device
TND 540: What’s Included
1
•Rand McNally TND
2
•Suction cup mount with adjustable bracket
3
•Vehicle charger
•Mini USB cable
4
5
•Anti-glare screen protector
1
5
™
Install the Mount
Note: Follow all local regulations governing the placement of the mount.
1. Select an area with a line of sight to the sky and GPS satellites.
2. Clean and dry the mounting area.
3. Remove the suction cup protective lm.
4. Adjust the angle of the mount using the thumbscrews.
5. Pull the suction cup lever up to release suction.
2
34
6. Plug the power cord into the device and the vehicle’s 12-volt
power source.
7. Optional: To use your vehicle’s speakers, connect an AUX cable from
the device’s AUX out to your vehicle’s AUX in port.
8. Slide the device onto the mount.
9. Place and hold the mount suction cup against the
mounting surface.
10. Press the suction cup lever down until it snaps into place.
11. Adjust the device so that it can be easily seen and does not
block the driver’s line of sight.
Thumbscrews
Charge the Battery
It is recommended that the device is always
connected to a power source during use.
Note: The vehicle may need to be on for the device to charge.
TND™ User Manual2
Press down
to hold
1. Your Device
TND™ User Manual3
1. Your Device
TND 740: What’s Included
1
•Rand McNally TND
2
•Magnetic mount
3
•Windshield mount with suction cup
•Vehicle charger
4
5
•USB cable
6
•Anti-glare screen protector
6
™
1
Install the Mount
Note: Follow all local regulations governing the placement of the mount.
1. Select an area with a line of sight to the sky and GPS satellites.
2. Clean and dry the mounting area.
3. Remove the suction cup protective lm.
4. Adjust the angle of the mount using the thumbscrews.
5. Pull the suction cup lever up to release suction.
6. Plug the power cord into the device and the vehicle’s 12-volt
power source.
2
3
7. Optional: To use your vehicle’s speakers, connect an AUX cable from
the Magnetic mount AUX out to your vehicle’s AUX in port.
8. Slide the device onto the mount.
9. Place and hold the mount suction cup against the
mounting surface.
10. Press the suction cup lever down until it snaps into place.
11. Adjust the device so that it can be easily seen and does not
block the driver’s line of sight.
4
5
Thumbscrews
Charge the Battery
It is recommended that the device is always
connected to a power source during use.
Note: The vehicle may need to be on for the device to charge.
Press down
to hold
TND™ User Manual4
1. Your Device
TND™ User Manual5
123
4
11
678910
2. Settings
Main Menu
1
Truck Tools
Select to enter truck information, set warnings, and access other tools.
2
Go To Map
Tap to view location on the map.
3
Guided Search
Tap to select an address or point of interest (POI).
4
DriverConnect
Tap to launch the DriverConnect app and log hours of service (HOS),
Driver-Vehicle Inspection Reports (DVIRs), and other compliance fea
5
tures.
Note: You must connect the TND to Rand McNally electronic logging device (ELD), such as the ELD-50 or DC-200, in order to use this
software.
5
Battery Power and Time Indicators
6
System Updates
Tap to check for software or system updates.
7
Brightness
Tap to adjust the screen brightness.
8
Volume
Tap to increase or decrease spoken instructions volume, and mute or
unmute spoken instructions.
Note: You can also tap this icon when it appears on the map screen
to mute/unmute.
9
Bluetooth
Tap to set up a Bluetooth connection.
Wi-Fi
10
Tap to select a Wi-Fi network or hotspot.
11
Settings
Look for this icon for help tips on many screens.
Tap to set device, route, or map preferences.
Note: Not all settings are available on all models.
Weight (Empty)Use the + and - buttons or enter a numeric
value by tapping the calculator.
Weight (Loaded)Use the + and - buttons or enter a numeric
value by tapping the calculator.
See Load Option in
Preferences › General (page 8)
or on the Main Menu (page 4).
Truck Info Options
Width Use the + and - buttons or enter a numeric
value by tapping the calculator.
Trailers Straight
48’
53’
Double
Triple
Number of Axles Use the + and - buttons.
Height Use the + and - buttons or enter a numeric
value by tapping the calculator.
TND™ User Manual8
2. Settings
Preferences
• Tap
• Tap the option to be set.
• Enter the new information.
• Tap X to close and save changes.
General PreferencesOptions
System Settings System Settings
GPS Repair
System Update
Skin Type Modern
Classic
Defaults to Modern. Use Classic skin type
for the look and feel of older TND models.
Vehicle Type Truck
Car/Light Truck
Bus
Yard Time Zone Hawaii
Alaska
Pacic Time
Arizona
Mountain Time
Central Time
Indiana (East)
Atlantic (Canada
Newfoundland
and to view the options.
General Preferences Options
My Custom POIs Manage Custom POIs
Select a Category to Edit
Hide All Icons on Map
Go to Map
Mileage Log Truck/Bus Only
Car Only
Truck & Car
Don’t Log Mileage
Screen Click Click O
Click On
Tutorial View Tutorial and Tips
Voice Name Allison
Samantha
Susan
Tom
LanguageEnglish (Basic)English (Advanced)
Español
Français
For the screen and spoken instructions.
UnitsU.S. Standard
Metric
Auto Select
Day / Night Mode Automatic
Always Day
Always Night
TND™ User Manual9
Load Prompt/ Prompt
NoticationAlways Loaded
2. Settings
Preferences - continued
General PreferencesOptions
Toll Prompt/ Enabled
Notication Disabled
Clock Setting12-Hour Clock24-Hour Clock
Contact & AboutTap to show version information and
copyrights.
Route PreferencesOptions
Note: The default settings for your device were optimized for the vehicle
route. Use the options below to ne-tune these settings.
Use Trac On
O
RecalculationManual RecalculateAuto Recalculate
Route Preferences Options
Turn Announcements Set three distances at which you want
to be warned about an upcoming turn.
The rst announcement will be the farthestfrom the turn and the third the closest.
Junction View Distance Tap - or + to set the distance
ETA Adjustment Increase ETA more
Increase ETA some
ETA OK
Decrease ETA some
Decrease ETA more
Route Fastest Route
Shortest Route
TollwaysAllow TollwaysAvoid Tollways
U-TurnsAllow U-TurnsAvoid U-Turns
FreewaysAllow All (Default) Avoid Freeways
Avoid Small Roads
Prefer Freeways
FerriesAllow FerriesAvoid Ferries
TunnelsAllow TunnelsAvoid Tunnels
TND™ User Manual10
Cross Country BordersAllow Crossing BordersAvoid Crossing Borders
Dirt RoadsAllow Dirt RoadsAvoid Dirt Roads
Manage Avoid List Roads
States/Provinces
Areas
Routes
Fast Recalc O
On
Preferences - continued
2. Settings
Map Preferences Options
.Map Style Light
Dark
High Contrast
Map Auto Zoom O
On, Auto Scale
On, Street Scale
On, City Scale
On, State Scale
Set to auto scale to keep the current
vehicle position and the next turn
in the map view at all times. Set to
street/city/state scale to specify the
maximum scale of the zoom.
Note: When in 3D Map mode with Auto Zoom on, the map will change to North Up at certain zoom levels. Also,
the visual turn screen will not appear in
3D mode with Auto Zoom on because a
close up view of the turn is not needed.
Lane Guidance O
On
Map Preferences Options
Truck POI Icons O
On
Select icons to display on map.
Address Book Icons O
On
Truck Icon 2D
3D
Bus Icon 2D
3D
Car/Light Truck Icon 2D
3D
Scroll left or right to select the vehicle
icon and color to display on the map.
Map View ModeHeading UpNorth Up
3D View
POI Icons O
On
Select icons to display on map.
Select restaurants, banks, gas
stations, etc. to display on the
map.Tapanycategorytollinthe
square and display those icons.
TND™ User Manual11
Route ColorMove the slider to the left or right to set the route color.
Preferences - continued
2. Settings
Warning Preferences Options
Warning/Alert Prompts None
Audio & Visual
Visual
Audio
Auto Dismiss WarningsNeverAfter 2 Seconds
After 10 Seconds
After 30 Seconds
Curve WarningsSet warning distance to curves areas by using the + and - buttons.
Hill WarningsSet warning distance to upcoming hills areas by using the + and - buttons.
Engine Brake WarningsSet warning distance to begin braking areas by using the + and - buttons.
Narrow Road WarningsSet warning distance to narrow roads areas by using the + and - buttons.
Warning Preferences Options
Warning Display Size Full Screen
Small Bar
Toll Booth AlertSet warning distance to toll booths by using the + and - buttons.
Construction AreaSet warning distance to construction areas by using the + and - buttons.
Speed LimitSet warning distance to speed limit changes by using the + and - buttons.
Set the amount over the posted limit at
which the warning appears.
Set a user-dened maximum speed to be warned whenever the vehicle exceeds that speed, regardless of limits.
Speed Limit ChangeSet warning distance to a change in
the speed limit by using the + and buttons.
Weigh Station Set warning distance to weigh stations
by using the + and - buttons.
State/Province Set warning distance to state/province
Border Alert borders by using the + and - buttons.
State or Province Border/ O
Timezone Change On
TND™ User Manual12
Note: To turn warnings o completely, tap “-” until OFF displays.
3. Maps
Basic Map View
12
4
6
Expanded Map View
Main Menu
1
Search For an Address
Tap to type in any address or search by keyword.
2
Compass Direction
Tap to change the map display. An icon displays the selected option:
North up (N), heading up (arrow), or 3D.
3
5
3
Zoom In
Tap to zoom in.
4
`Route Distance
Reects the distance from your point of origin to your destination.
5
Zoom Out
Tap to zoom out.
6
Map View Tab
Tap to expand the map screen. By default, icons are minimized to
show simply the search bar, compass direction, and zoom. Tap again
to switch back to the default view.
7
Exit Points of Interest (POI)
Tap to view POIs along the exit ahead.
7
8
8
Live Data
Tap to view fuel, weather, and trac along the route. (Requires Wi-Fi)
9
Virtual Dashboard
10
Current Speed
1011
9
6
12
Tap to display the Virtual Dashboard.
11
Clock/Elevation
Tap to toggle between the clock and elevation.
12
Home (Main Menu)
Tap to return to the TND home screen.
TND™ User Manual13
3. Maps
Search For an Address
1. Tap the search bar at the top of the Navigation screen to type in any
address or search by keyword. Or, tap any of the categories to search for
specic types of destinations.
2. Once a destination is entered, tap Navigate and your route options will
display.
3. Select either the fastest route or an alternate route.
4. Tap Start Navigation to begin the route.
Note: If a keyword search does not give the results you need, refer to the
Guided Search section beginning in Chapter 4.
TND™ User Manual14
3. Maps
Helpful Tips on Entering Addresses
Auto-Complete Feature
Enter the rst few characters in a name and a short list displays
names that start with the typed characters. Continue entering characters
until the searched-for name displays in the list. Tap the name to select it.
Cities
Cities with common names, such as “Athens”, may have multiple locations.
The tablet will list all locations. If a name does not display, continue typing
characters until the name you are looking for displays in the list.
State or County Routes
If you’re entering a State or County Route, it’s usually best to rst either enter
the State or County initials, (for example, State Road 535 would be entered
as “SR”) but you may also need to try other options, such as “State Road” or
“CA” for California, for example.
Nearby vs Along Route
You can modify the search to include all areas near your current location by
selecting Nearby, or in areas along your current route by selecting Along
Route. Tap the Change button to alternate between these searches.
Truck Loads
After setting a destination, you must conrm if the truck is loaded or not. Tap
a button to indicate:
Empty: The truck is not loaded
Loaded: The truck is loaded
Always Loaded: The Loaded option will always be selected, and this page
will no longer display.
TND™ User Manual15
3. Maps
Points of Interest
1
3
2
You can also use the Map function to search for Points of Interest (POIs)
along your route, or near your current location. POIs are organized by categories.
1
Tap a POI category in the Search bar.
2
Displays POIs nearby, or along your route.
3
Tap to view additional POI categories..
4
Select a category, and locate a POI from the expanded list.
Note: Turns red when speed limit warning exceeded.
(See page 12 to set speed limit alert.)
4
56
5
Tap the POI.
6
Tap Navigate, Add to Address Book, or Add as Via.
Note: The Address Book icon in the Search bar contains a list of destina-
tions you have added to your address book.
TND™ User Manual16
3. Maps
Route Map Window
3
1
4
2
5
6
7
16
8
12
15
13
1
Next Maneuver
Tap to repeat spoken next maneuver instructions.
2
Road Name
Name of street you will turn onto next.
3
Directions Slide-Out List
Tap to select a route display option.
4
Compass Direction
Tap to change the map display. An icon in the upper right corner displays
the selected option: North up (N), heading up (arrow), or 3D (3). Also displays Wi-Fi status.
5
Exits Quick View
Slide out to show upcoming exit information.
6
Live Data
Tap to view Trac, Weather, and Fuel Price Information.
Note: This feature requires a Wi-Fi connection.
7
Zoom In/Zoom Out
1110
914
8
Map View Tab
Tap to simplify the map screen. Icons are minimized to show simply the
zoom, next maneuver, and miles/time.
9
Home Screen
10
Miles/Time
Displays remaining distance. Tap to select from: yard arrival time,
arrival time, remaining time, yard time, and elevation.
11
Current Mile Marker
Tap to open a “Tell Rand” message.
12
Current Information
View current information by city, street, or upcoming intersection. Also
displays advanced lane guidance and weather overlay key, when enabled.
Tap to change. (Note: For some destinations, the “Am I close?” feature counts down addresses as the vehicle approaches.)
City, county, and stateCurrent street name
Next intersecting street nameAdvanced lane guidance
13
Current Speed
Tap to display the Virtual Dashboard. Turns red for speed warnings.
14
Virtual Dashboard
15
Location and Route Options
Tap to see current location information, change route settings, detour,
cancel a route, and manage avoided roads.
16
Speed Limit
Orange for truck limit; white for general limit. Tap to open a “Tell Rand”
message about speed limits.
17
TND™ User Manual17
Loading...
+ 48 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.