Rand McNally OverDryve 7, OverDryve 7 Pro Getting Started

QUICK START GUIDE

This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:

(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement

This device complies with FCC SAR exposure limits set forth for an uncontrolled
environment.

SAR compliance for using the equipment in close proximity to the human body
has been evaluated at 0mm.

This equipment must not be co-located or operating in conjunction with any other
antenna or transmitter.

End-users and installers must be provide with antenna installation instructions and
consider removing the no-collocation statement.

This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that
may cause undesired operation.

Caution!

Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.

Canada Statement

This device complies with Industry Canada’s licence-exempt RSSs. Operation is
subject to the following two conditions:

(1) This device may not cause interference; and

(2) This device must accept any interference, including interference that may cause
undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux
appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions
suivantes :

(1) l’appareil ne doit pas produire de brouillage;

(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le fonctionnement.

This equipment should be installed and operated with a minimum distance of
0mm between the radiator and your body.

Cet équipement devrait être installé et actionné avec une distance minimum de
0mm entre le radiateur et votre corps.

This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.

Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en même temps
qu'aucune autre antenne ou émetteur.

The device for operation in the band 5150–5250 MHz is only for indoor use
to reduce the potential for harmful interference to co-channel mobile satellite
systems.

Les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés
uniquement pour une utilisation à l’intérieur afin de réduire les risques de
brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes
canaux.

Your OverDryve™ Unit

Caution: Important Safety Information
Navigation

• Use this device at your own risk.

• Attend to this device only when it is safe to do so.

• Traffic laws and regulations always have priority over any
instructions from the navigation system.

NOTE: If you do not understand the spoken instructions or are unsure
of what to do, refer to the navigation map on your device.

Installation

• Make sure that the mount is securely mounted and properly
adjusted before each trip.

• Make sure that the mount does not impair the driver’s visibility.

• Do not attach the mount within the airbag deployment zone.

• Install the mount in a manner that minimizes risk in the event of
an accident.

• After installation, check all safety-related equipment to ensure that
it operates without interference from the device, its cables, or any
other accessories.

• Connect the wall charger to a 120V or 240V outlet only.

• Connect the vehicle charger to a 12V outlet only.

Device

• Do not use sharp-edged objects on the device touch screen.

• The device is not waterproof and is not protected against
water damage.

• Protect the device from extreme temperatures. Operating
temperature for the device is between 32 degrees F and
120 degrees F.

• Do not open the device casing.

• Do not attempt to replace the battery. Contact Rand McNally
Customer Support with questions about the battery.

• Always follow local regulations when disposing of this device.
NOTE: Make sure that there are no kinks in the cable and that it will

not be damaged by any sharp objects.

NOTE: Use only a moist cloth to clean the device.
NOTE: Do not pull the cable to unplug the unit.

2 OverDryve™ Quick Start Guide

Box Contents

Your OverDryve

• OverDryve™ Unit

• Smart mount

• Bracket with suction cup

• Car charger

• USB wall charger

• Dash mount disc

• FM transmitter antenna

• AUX cable

• Anti-glare screen protector

Your OverDryve

™

3OverDryve™ Quick Start Guide

Install the Mount

OverDryve

Quick Start Guide

NOTE: Follow all local laws and regulations governing the placement of the mount.

1. Select an area with a line of sight to the sky and GPS satellites.

2. Clean and dry the mounting area.

3. Remove the suction cup protective fi lm.

4. Attach the two pieces of the mount together and lock into place.

5. Adjust the angle of the mount.

6. Pull the suction cup lever up to release suction.

7. Plug the power cord into the mount and the vehicle's 12-volt power source.

8. Place and hold the mount suction cup against the
mounting surface.

9. Press the suction cup lever down until it snaps
into place.

10. Snap the tablet onto the mount.

11. Adjust the tablet so that it can be easily seen and
does not block the driver's line of sight.

4 OverDryve™ Quick Start Guide