Radio Shack ET-536, ET-549 User Manual

43-103 6.fm Page 1 Tuesday, August 17, 1999 9:52 AM

Cordless Telephone

Cat. No. 43-1036/1049

OWNER’S MANUAL

Please read before using this equipment.

with 10-Number Memory

ET-536/10-Channel
ET-549/25-Channel

y

y

y

g

g

g

g

y

43-103 6.fm Page 2 Tuesday, August 17, 1999 9: 52 AM

FEATURES

Your RadioShack ET-536 10 Channel/
ET-549 25-Channel Cordless Tele­phone with 10-Number Mem ory is de­signed to exacting standards that
ensure reliability, long life, and out­standing performance.

Its features include:

10 Channels (ET-536) / 25 Channels
(ET-549)

— lets you change to a clear­er channel during a call to reduce static
interference.

10-Number Memor

Dialing

— lets
you store up to 10 numbers in memory
for easy dialing.

Super CCT Noise-Reduction
Circuitr

— provides clear telephone
conversations, giving you sound clarity
comparable to that of a corded phone.

Securit

Access-Protection Code

—

automatically prevents other cordless
phone users from using your phone
line while the handset is off the cradle.

— lets you send a paging signal

Pa

e

from the base to the hand set to page
someone or loca te the handset if you
misplace it.

Flash

— sends an electron ic switch­hook signal for use with special phone
services, such as Call Waiting.

Pro

rammable Ringers

— let you
select from four ringer types and
change the type from the handset.

Tone/Pulse Dialin

— lets you use

your phone with tone or pulse service.

Quick Talk

— lets you make or an­swer a call by simply lifting the handset
from the base.

Hearin

-Aid Compatibilit

— lets
you use your phone with he aring aids
that have a T (telephone) switch.

This telephone has been tested and
found to comply with all applicable UL
and FCC standards.

®

COM-LOK

— ensures that other
cordless phone users cannot u se your
phone line when the handset is on the
cradle.

Redial

— lets you quickly redial the

last number dialed.

© 1997 Tandy Corporation.

COM-LOK is a registered trademark used by Tandy Corporation

RadioShack is a trademark used by Tandy Corporation.

All Rights Reserv ed .

2

We recommend you record your
phone’s serial number here. The num­ber is on the bottom panel of the base.

Serial Number: __________________

43-103 6.fm Page 3 Tuesday, August 17, 1999 9: 52 AM

Important Note: Cordless phones
such as this one require AC power to
operate. When the AC power is off,
you cannot dial out or receive incoming
calls using your ET-536/ET-549. To be
safe, you should also have a phone
that does not need AC power t o oper­ate (not a cordless phone) so you can
still make and receive ca lls if there is
an AC power failure.

Warning: To prevent fire or shock
hazard, do not expose this product to
rain or moist u re .

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER OR BACK. NO USER-SERVICE­ABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED PERSONNEL.

This sym bol is in te nd ed to a le rt yo u

to the pr e s en ce of uninsulated da n-

gerous voltage within the product’s

enclos u re t h at m ig ht b e of s ufficie nt

magnitude to constitute a risk of

electric shock. Do not open the

product’s case.

This symbol is intended to inform

you that important operating and

!

maintenance instructions are in-

cluded in th e l itera ture a ccomp an y-

ing this product.

!

READ THIS BEFORE
INSTALLATION

Each device that you connect to the
phone line draws power from the
phone line. We refer to this power draw
as the device’s Ringer Equivalence
Number, or REN. The REN is shown
on the bottom of the base.

If you are using more than one phone
or other device on the line, add up all
the RENs. If the total is more than five,
your phones might not ring. In rural ar­eas, a total REN of three might impair
ringer operation. If ringer operation is
impaired, remove a device from the
line.

FCC STATEM ENT

This telephone complies with Part 68

FCC Rules

of
quest, provide the FCC Registration
Number and the REN to your phone
company. These num bers are located
on the bottom panel of the base.

Note: You must not connect your
phone to any of the following:

• coin-operated syst e ms

• party-line systems

• most electronic key phone sys­tems

. You must, upon re-

3

g

43-103 6.fm Page 4 Tuesday, August 17, 1999 9: 52 AM

CONTENTS

Installation ............................................................................................................ 5

Selecting a Location ........................................................................................ 5

Placing th e Base on a Desk Top ............................................................... 5

Mounting the Base on a Wall Plate ........................................................... 6

Mounting the Base Directly on the Wall .................................................... 8

Connecting and Charging the Battery .. ........................................................... 9

Setting the Dialing Mode ............................................................................... 11

Setting the Ringer Tone and Volume ............................................................. 11

Operation ............................................................................................................ 12

Making and Receiving Calls .......................................................................... 12

Changing the Channel ....................................................................................12

Using Redial .................................................................................................. 12

Using Flash .................................................................................................... 13

Using Tone Services on a Pulse Line ............................................................ 13

Paging ........................................................................................................... 14

Memory Dialing .............................................................................................. 14

Storing a Number in Memory ...................................................................14

Entering a Pause .................................................................................... 15

Dialing a Memory Number ...................................................................... 15

Chain-Dialing Service Numbers .............................................................. 15

Testing Stored Emergency Numbers ...................................................... 15

Troubleshootin

Care and Maintenance ....................................................................................... 18

Replacing the Battery .................................................................................... 19

The FCC Wants You to Know ........................................................................ 20

Lightning ........................................................................................................ 20

4

................................................................................................. 16

43-103 6.fm Page 5 Tuesday, August 17, 1999 9: 52 AM

INSTALLATION

SELECTING A LOCATION

You can place the phone on a desk top
or table, or mount it on a wall. Select a
location that is:

• near an AC outlet

• near a telephone line jack

• out of the way of normal activities

• away from electrical machinery,
electrical appliances, metal walls
or filing cabinets, wireless inter­coms, alarms, and room monitors

• away from other cordless phones

The base’s location affects the hand­set’s range. If you have a choice of
several locations, try each to see
which provides the best performance.

Caution:

adapter was designed specifically for
your ET-536/ET-549. Use only the
supplied adapter.

Notes:

• Your telephone connects directly

The supplied RadioShack

to a modular telephone line jack. If
your phone line jack is not a mod­ular jack, you can update the wir­ing yourself, using jacks and
adapters available at your local
RadioShack store. Or, you can let
the phone company update the
wiring for you.

• The USOC number o f the jack to
be installed is RJ11C (RJ11W if
you want to mount it on a wall
plate).

Placing the Base
on a Desk Top

Follow these steps when you place
the base on a desk, shelf, or table.

1. Plug one end of the supplied mod­ular cord into the
the back of the base.

2. Insert the supplied AC adapter’s
barrel plug into the
on the back of the base.

TEL LINE

jack on

DC IN 9V

jack

• The phone company will charge
you for the installation of neces­sary jacks.

5

43-103 6.fm Page 6 Tuesday, August 17, 1999 9: 52 AM

3. Route the adapt er’s cord through
the strain relief slot on top of the
base.

4. Plug the adapter into a standard
AC outlet. The POWER indicator
on the base lights.

Mounting the Base
on a Wall Plate

1. Plug one end of a short modular
cord (such as Cat. No. 279-390,
not supplied) into the
jack on the back of the base.

2. Insert the supplied AC adapter’s
barrel plug into the
on the back of the base.

TEL LINE

DC IN 9V

jack

5. Plug the modular cord’s other end
into a modular phone line jack.

6. Fully extend the base’s antenna
and place it in a vertical position.

6

43-103 6.fm Page 7 Tuesday, August 17, 1999 9: 52 AM

3. Route the modular cord through
the top groove and the adapter
cord through both grooves on the
bottom of the base.

Top
Groove

Both
Grooves

4. Plug the adapter into a standard
AC outlet. The POWER indicator
on the base lights.

5. Plug the short modular cord’s
other end into the wall plate jack,
then align the base’s keyhole slots
with the wall plate studs and slide
the base downward to secure it.

6. Press and lift out the handset
holder, rotate it 180°, then snap it
back into place so it holds the
handset.

7. Fully extend the base’s antenna
and place it in a vertical position.

7

1

43-103 6.fm Page 8 Tuesday, August 17, 1999 9: 52 AM

Mounting the Base
Directly on the Wall

For this mounting method, you need
two wood screws (not supplied) with
heads that fit into the keyhole slots on
the bottom of the base.

1. Drill two holes 3
inches apart. Then
thread a screw into
each hole, letting
the heads extend

5

about

/16 inch from

the wall.

2. Plug one end of the supplied mod­ular cord into the
the back of the base.

15

/

16

TEL LINE

3

15

16

/

jack on

4. Route the modular and adapter’s
cords through both grooves on the
bottom of the base.

5

1

/

Both
Grooves

5

/

Both
Grooves

5. Plug the adapter into a standard
AC outlet. The POWER indicator
on the base lights.

3. Insert the supplied AC adapter’s
barrel plug into the

DC IN 9V

jack

on the back of the base.

8

43-103 6.fm Page 9 Tuesday, August 17, 1999 9: 52 AM

6. Plug the cord’s other end into a
modular phone line jack.

7. Align the keyhole slots with the
mounting screws and slide the
base downward to secure it.

CONNECTING AND
CHARGING THE
BATTERY

The ET-536/ET-549 comes with a re­chargeable nickel-cadmium bat tery in­stalled in the handset. Before using
your phone, you must connect the bat­tery then charge it for about 14 hours.

1. Remove the screw on the battery
compartment cover on the bottom
of the handset. Press down and
slide off the handset’s battery
compartment cover in the direc­tion of the arrow.

8. Press and lift out the handset
holder, rotate it 180°, then snap it
back into place so it holds the
handset.

9. Fully extend the base’s antenna
and place it in a vertical position.

2. Insert the battery pack’s plastic
connector into the phone’s socket.
The plug fits only one way.

3. Replace the cover and tighte n the
screw.

4. To charge the battery, simply
place the handset on the base.

9

43-103 6.fm Page 10 Tuesday, August 17, 1999 9:52 AM

The CHARGE indicator on the base
lights.

Recharge the battery when the B ATT
LOW indicator flashes.

Notes:

• If the CHARGE indicator does not
light when you pla ce the handset
on the base, be sure the battery
and AC adapter are correctly and
securely connected.

• When you first use the phone after
charging or recharging the battery,
the phone might not work and you
might hear an error tone. If this
happens, return the handset to
the base for about 5 seconds.

• If the BATT LOW indicator does
not light, but the phone does not
work, recharge the battery. The
battery charge might be too low to
light the ind ic at o r.

• If the battery pack gets weak dur­ing a call, the handset sounds a
beep every 30 seconds, and the
BATT LOW indicator flashes every
3 seconds. If this happens, you
cannot make another call on the
phone until you recharge the bat­tery.

• About once a month, fully dis­charge the battery by keeping the
handset off the base until the
BATT LOW indicator lights. Other­wise, the battery loses its ability to
fully recharge.

• Using a pencil eraser, clean the
charging contacts on the handset
and the base about once a m onth
to make sure they are not dirty or
tarnished.

• If the battery gets completely dis­charged, the ET-536/ET-549
loses the security access-protec­tion code. To reset the security
code, place the handset on the
base and charge the battery.

• The supplied battery should last
for about a year. When the battery
loses its ability to fully recharge,
order a replacement battery from
your local RadioShack store (see
“Replacing the Battery” on Page

19.

10

43-103 6.fm Page 11 Tuesday, August 17, 1999 9:52 AM

SETTING THE D IALING
MODE

P

T

• •

Set
the type of service you have. If you
are not sure which type you have, do
this test.

1. Set

2. Lift the handset and listen for a

3. Press any number other than

on the back of the base for

P

T

• •

to T (tone).

dial tone.

0

.

Note:

If your phone system

requires that you dial an access

9

code (

, for example) before you
dial an outside number, do not
press the access code either.

If the dial tone stops, you have

P

touch-tone service. Leave

• •

set to T.
If the dial tone continues, you

P

T

• •

have pulse service. Set

to

(pulse).

1. Lift the handset. If you hear a dial
tone, press

2. Press

TALK

RINGER

to turn it off.

. The phone sounds
the current ringer tone and vol­ume.

3. Repeatedly press

RINGER

until
you hear the desired ringer tone
and volume.

Each time you press

T

ringer changes in the following

RINGER

, the

order:

High-volume “chirping”

P

Low-volume “chirping”

High-volume “warbling”

SETTING THE R INGER
TONE AND VOLUME

You can select one of four different
ringer/tone volume settings when the
phone is not in use.

Low-volume “warbling”

11

43-103 6.fm Page 12 Tuesday, August 17, 1999 9:52 AM

OPERATION

MAKING AND
RECEIVING CALLS

To make or answer a call, lift the hand­set. Or, if the handset is away from the
cradle, press
indicator on the handset and the IN
USE indicator on the base light.

To end a call, place the handset on the
cradle or press the handset’s
button.

If you press

Note:

and the phone does not disconnect,
place the handset on the cradle or
press
handset closer to the base.

TALK

TAL K

. The BATT LOW

TALK

TA LK

to hang up

again while holding the

CHANGING THE
CHANNEL

If you notice interference, static, or
noise during a call, you c an press
(channel) to find a clearer channel.

The ET-536/ET-549 c hanges to a dif­ferent channel each time you press

CH

.

: If the handset is too far from the

Note

base, the channel might not change.
Move closer to the base and try again.

CH

USING REDIAL

12

REDIAL

number dialed. When you hear a dial
tone, simply press

lets you quickly dial the last

REDIAL

.

43-103 6.fm Page 13 Tuesday, August 17, 1999 9:52 AM

Notes:

• The redial memory holds up to
32 digits, so you can redial long­distance as well as local num­bers.

• The redial memory also holds
pause entries. See “Entering a
Pause” on Page 15.

• The redial memory does not store
a flash entry or any digits you

FLASH

press after

(see “Using

Flash.”).

USING FLASH

FLASH

performs the electronic equiva­lent of a switchhook operation for spe­cial services, such as Call-Waiting.

USING TONE SERVICES
ON A PULSE LINE

Some special services , such as bank­by-phone, require tone signals. If you
have pulse service, you can still use
these special tone services by follow­ing these steps.

P

T

1. Be sure

2. Lift the ha ndset fr om the cr adl e or
press

3. Dial the service’s main number.

4. When the service answers, press

TONE

you dial are sent as tone signals.

• •

is set to P.

TALK

.

. Any additional numbers

For example, if you hav e call waiting,

FLASH

press

to answer an incoming
call without disconnecting the current
call. Press

FLASH

again to return to

the first call.
Note: If you do not have any special

phone services, pressing

FLASH

might

disconnect the current call.

5. After you complete the call, return
the handset to the cradle or press

TALK

. The phone automatically

resets to the pulse mode.

13

43-103 6.fm Page 14 Tuesday, August 17, 1999 9:52 AM

PAGING

To page the person who has the hand­set or to locate the handset when the
phone is not in use, press

PAGE

on the

base. The handset beeps five times.

MEMORY DIALING

You can store up to 10 numbers in
memory, then dial a stored number by
pressing a one-digit memory location
number.

Note:

Each number you store can be

up to 16 digits long.

Storing a Number in Memory

Note:

An error tone sounds and the
phone exits the programm ing mode if
you wait more than 20 seconds be­tween each key press.

1. Lift the handset. If you hear a

MEMO

PAUSE

Each

MEMO

TALK

to turn it off.

. The BATT LOW

TONE

entries (see “Using

TONE

or

PAUSE

entry

, then enter the mem-

0-9

). A single

tone, press

2. Press
indicator blinks.

3. Enter the number and any
and
Tone Services on a Pulse Line” on
Page 13 and “Entering a Pause”
on Page 15).

Note:

uses one digit of memory.

4. Press
ory location number (
tone sounds to indicate that the
number is stored.

14

Note:

If five quick beeps sound,
you have made an entry error a nd
the number was not stored. Start
again from Step 2.

43-103 6.fm Page 15 Tuesday, August 17, 1999 9:52 AM

5. For each stored number, write the
person’s or company’s name next
to the appropriate location number
on the supplied MEMORY direc­tory sticker. (Use a pencil in case
you want to change the number
later.) Attach the sticker to the
phone.

To erase a stored number, simply
store a new number in its place. Or,
skip Step 3, then press the memory lo­cation number (
A tone sounds.

0-9

) you want to clear.

Entering a Pause

In some telephone systems, you m ust
dial an access code (
and wait for a second dial tone b efore
you can dial a n outside number. You
can store the access code with the
phone number. However, you should
also store a pause after the access
code to allow the outside line time to
connect.

9

, for example)

To do so, press
enters a 2-second pause. For a longer
pause, press

PAUSE

PAUSE

. Each press

additional times.

Dialing a Memory Number

To dial a number stored in memory, lift
the handset from the cradle or press

TA LK

.

When you hear a dial tone, press

MEMO

and enter the memory location
number for the number you want to
dial.

Chain-Dialing Service
Numbers

When calling special services (such as
alternate long distance or bank by
phone), dial the service’s main number
first. Then, at the appropriate place in
the call, press
for the location where the additional in­formation is stored.

MEMO

and the num ber

Testing Stored Emergency
Numbers

If you store an emergency service’s
number (police department, fire de­partment, ambulance) and you choose
to test the stored number, make the
test call during the late evening or early
morning hours to avoid peak demand
periods. Also, remain on the line to ex­plain the reason for your call.

15

43-103 6.fm Page 16 Tuesday, August 17, 1999 9:52 AM

TROUBLESHOOTING

We do not expect you to have any problem s with y our phone, but if you d o, the fol­lowing suggestions might help.

Problem Suggestion

Low volume or unusual
sounds.

Severe noise interference. • Press

The phone cannot be oper­ated at a useful distance from
the base because the signal
becomes weak or noisy
(handset’s range has
decreased).

The phone does not work or
works poorly.

The handset battery does not
charge.

Someone has picked up another phone on the
same line. Hang up the other phone.

• Keep the handset away from computers,
remote control toys, wireless microphones,
alarm systems, intercoms, room monitors,
fluorescent lights, and electrical appli­ances.

• Move to another location or turn off the
source of interference.

• Fully extend the base’s antenna in a verti­cal position.

• Be sure neither antenna is touching a
metal surface.

• Return the handset to the cradle, and
recharge the battery.

Be sure the base’s phone line cord and AC
adapter are correctly and securel y connected,
and the battery is charged.

• Check the charging contacts on the hand­set and base. If they are dirty, clean them
with a pencil eraser.

CH

to change the channel.

16

• Be sure the battery is connected correctly.

43-103 6.fm Page 17 Tuesday, August 17, 1999 9:52 AM

Problem Suggestion

Handset does not ring or
receive a page.

The handset stops working or
works poorly during a call.

• The battery pack might be weak. Charge
the battery.

• Extend the base’s antenna vertically.

• Move the handset closer to the base.

• Move the base away from other electrical
devices and sources of noise.

• Move the handset closer to the base.

• Fully extend the base’s antenna, and place
it in a vertical position.

• Make sure the charging contacts on the
handset and base are clean.

• Be sure the handset’s battery is charged.
(If the battery power is too low, it does not
have enough power to light the BATT LOW
indicator.)

• If the base loses power while the handset
is off of it, the security access-protection
code might change. Restore power to the
base, then place the handset back on the
base. The CHARGE indicator lights, indi­cating that the code is set again.

The call is too noisy . Change channels or hang up and redial the

number.

If you still have problems, disconnect the phone. If other phones on the same line
work properly, the fault is in this phone or its installation. If you cannot find the prob­lem, take your phone to your local RadioShack store for assistance

17

43-103 6.fm Page 18 Tuesday, August 17, 1999 9:52 AM

CARE AND MAINTENANCE

Your RadioShack ET-536 10 Channel/ET-549 25-Channel Cordless Telephone with
10-Number Memory is an example of s uperior design and craftsmanship. The f ol­lowing suggestions will help you care for your cordless telephone so you can enjoy
it for years.

Keep the phone dry. If it gets wet, wipe it dry immediately. Liquids
might contain minerals that can corrode the electronic circuits.

Handle the phone gently and carefully. Dropping it can damage cir­cuit boards and cases and can cause the phone to work improperly.

Use and store the phone o nly in no rmal tem perature environm ents.
Temperature extremes can shorten the life of electronic devices and
distort or melt plastic parts.

Keep the phone away from dust and dirt, which can cause premature
wear of parts.

Wipe the phone with a damp cloth occasionally to keep it looking

CLEANER

new. Do not use harsh chemicals, cleaning solvents, or strong deter­gents to clean the phone.

Modifying or tampering with the telephone’ s int ernal com pone nts can cause a mal­function and might invalidate your telephone’s warranty and void your FCC authori­zation to operate it. If your phone is not performing as it should, take it to your local
RadioShack store for assistance. If the trouble is affecting the phone lines, the
phone company might ask you to disconnect your phone until you have resolved the
problem.

18

43-103 6.fm Page 19 Tuesday, August 17, 1999 9:52 AM

REPLACING THE
BATTERY

If you follow the instructions in “Con­necting and Charging the Battery” on
Page 9, the battery should l ast about
one year. If the battery will not hold a
charge for more than 2 hours after an
overnight charge, replace the battery
with a new 3.6 V, 300 mAh battery with
a conn ector th at fits the s ocket in the
battery compartment. You c an order a
replacement battery through your local
RadioShack store.

Install the new battery as described
below, then charge the battery (see
“Connecting and Charging the Bat­tery” on Page 9).

Note:

To avoid losing phone num bers
stored in memory, try to install and be­gin charging the new battery within 1
minute.

2. Gently pull on the battery connec­tor to disconnect it, then remove
the battery.

3. Insert a fresh battery and insert its
connector into the socket inside
the battery compartment.

4. Replace the cover and tighte n the
screw.

Cautions:

• You must use a replacement bat­tery of the same size and type.

• Do not dispose of the battery in a
fire because it might explode.

• Do not open or mutilate the bat­tery.

• Be careful not to short the battery
by touching it with conducting
materials, such as rings, brace­lets, and keys. The battery or con­ductor might overheat and burn.

1. Remove the screw on the battery
compartment cover on the bo ttom
of the handset. Press down and
slide off the handset’s battery
compartment cover in the direc­tion of the arrow.

Important:

chargeable nickel cadmium battery. At
the end of the battery’s useful life, it
must be recycled or disposed of proper­ly. Contact your local, county, or state
hazardous wa ste managemen t authori­ties for information on recycling or dis­posal programs in your area. Some
options that might be availab le are: mu­nicipal curb-side collection, drop-off box­es at retailers such as your local
RadioShack store, recycling collection
cent ers , an d mail - b ack pro g rams .

This produc t contains a re-

19

43-103 6.fm Page 20 Tuesday, August 17, 1999 9:52 AM

THE FCC WANTS YOU
TO KNOW

In the unlikely event that your phone
causes problems on the phone line,
the phone company can temporarily
discontinue your service. If this hap­pens, the phone com pany attem pts to
notify you in advance. If adv ance no­tice is not practical, the phone compa­ny notifies you as soon as possible and
advises you of your right to file a com ­plaint with the FCC.

Also, the phone company can make
changes to its lines, equipment, opera­tions, or procedures that could affect
the operation of this telephone. The
telephone company notifies you of
these changes in advance, so you can
take the necessary steps to prevent in­terruption of your telephone service.

Your phone m ight cause TV or radio
interference even when it is operat ing
properly. To determine whether your
phone is causing the interference, turn
off your phone. If the interference goes
away, your phone is ca using the inter­ference.

Try to eliminate the interference by:

• Moving your phone away from t he
receiver

• Connecting your phone to an A C
outlet that is on a different electr i­cal circuit from the receiver

• Contacting your local Ra­dioShack store for help

If you cannot eliminate the interfer­ence, the FCC requires that you stop
using your phone.

Some cordless phones operate at fre­quencies that might cause interference
to nearby TVs and VCRs. To minimize
or prevent such interference, the base
of the cordless phone should not be
placed near or on top of a TV or VCR.

LIGHTNING

Your telephone has built-in lightning
protection to reduce the risk of damage
from surges in telephone line and pow­er line current. This lightning protection
meets or exceeds FCC requirem ents.
However, lightning striking the tele­phone or power lines can damage your
telephone.

20

Lightning damage is not common.
Nevertheless, if you live in an area that
has severe electrical storms, we sug­gest you unplug your phone during
storms to reduce the possibility of
damage.

43-103 6.fm Page 21 Tuesday, August 17, 1999 9:52 AM

NOTES

21

43-103 6.fm Page 22 Tuesday, August 17, 1999 9:52 AM

22

43-103 6.fm Page 23 Tuesday, August 17, 1999 9:52 AM

23

g

g

g

g

g

g

g

g

g

g

g

g

43-103 6.fm Page 24 Tuesday, August 17, 1999 9:52 AM

Limited One-Year Warranty

This product is warran ted by RadioShac k against manufacturing defects in material and workman­ship under normal use for one (1) year from the date of purchase from RadioShack company-owned
stores and author ized Radi oS hack fr anchi sees an d deal er s. In the even t of a pr oduct defe ct du rin
the warranty period, take the product and the RadioShack sales receipt as proof of purchase date to
any RadioShack store. RadioS hack will, at its option, unless other wise provided by law : (a) correct
the defect by product re pair without char
the same or similar desi
products on which a refund is made, become the property of Radi oShack. New or reconditioned
parts and products may be used in the performance of warranty service. Repaired or replaced parts
and products are warranted for the remainder of the ori
repair or replacement of the product made after the expiration of the warranty period.
This warranty does not cover: (a) dama
accident, misuse, impr oper or abnormal usa
maintenance, a lteration, li
other than those provided by a RadioShack Autho rized Service Facility; ( c) consumables such as
fuses or batteries; (d) cos metic dam a
of product removal, installation, set-up service adjustment or reinstallation.
EXCEPT AS PROVIDED HEREIN, RadioShack MAKES NO EXPRESS WARRANTIES AND ANY
IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE DURATION OF THE WRITTEN
LIMITED WARRANTIES CONTAINED HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack
SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON
OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR
INDIRECTLY BY USE OR PERFORMANCE OF THE PRODUCT OR ARISING OUT OF ANY
BREACH OF THIS WARRANTY, INCLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULT­ING FROM INCONVENIENCE, LOSS OF TIME, DATA, PROPERTY, REVENUE, OR PRO FIT OR
ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF Ra­dioShack HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Some states do not allow the limitations on how lon
cidental or consequentia l dama
This warranty
state to state.

RadioShack Customer Relations, Dept. W, 100 Throckmorton St., Suite 600, Fort Worth, TX 76102

ives you specific legal rights, and you may also have other rights which vary from

n; or (c) refund the purchase price. All repla ced parts and products, and

e or failure caused by or attributable to acts of God, abuse,

htning or other incidence of excess voltage or cu rrent; (b) any repairs

e; (e) transportatio n, shippi ng or insurance cost s; or ( f) costs

es, so the above limitations or exc lusions may not apply to you.

We Service What We Sell

e for parts and labor; (b) rep lace the produ ct with one of

inal warranty period. You will be charged for

e, failure to follow instructions, improper installation or

an implied warranty lasts or the exclusion of in-

1/97

RadioShack

A Division of Tandy Corpor ation

Fort Worth, Texa s 76102

UDZZ01500ZZ

3A7 Printed in Hong Kon