Quadra-Fire EXCURSION-I, EXCURSION-III, EXCURSION-II Owner's Manual

1

Quadra-Fire • EXCURSION-I, EXCURSION-II, EXCURSION-III Owner’s Manual • 2538-981 Rev. B • 2/19

Owner’s Manual

Care and Operation

NOTICE: DO NOT discard this manual!

This appliance may be installed as an OEM
installation in manufactured home (USA
only) or mobile home and must be installed
in accordance with the manufacturer’s
instructions and the Manufactured Home

Construction and Safety Standard, Title 24
CFR, Part 3280 in the United States, or the
Standard for Installation in Mobile Homes,
CAN/CSA Z240 MH Series, in Canada.

This appliance is only for use with the type(s)
of gas indicated on the rating plate. This
appliance is not convertible for use with other

gases, unless a certied kit is used.

In the Commonwealth of Massachusetts installation must be

performed by a licensed plumber or gas tter.

See appliance installation manual for additional
Commonwealth of Massachusetts requirements.

INSTALLER: Leave this manual with party responsible for use and operation.
OWNER: Retain this manual for future reference.
Contact your dealer with questions regarding installation, operation or service.

• DO NOT store or use gasoline or other am-

mable vapors and liquids in the vicinity of this
or any other appliance.

• What to do if you smell gas

- DO NOT try to light any appliance.

- DO NOT touch any electrical switch. DO
NOT use any phone in your building.

- Leave the building immediately.

- Immediately call your gas supplier from
a neighbor’s phone. Follow the gas sup­plier’s instructions.

- If you cannot reach your gas supplier, call

the re department.

• Installation and service must be performed

by a qualied installer, service agency, or the

gas supplier.

WARNING:
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly
could result in serious injury, death, or
property damage.

DANGER

HOT GLASS WILL

CAUSE BURNS.

DO NOT TOUCH GLASS

UNTIL COOLED.

NEVER ALLOW CHILDREN

TO TOUCH GLASS.

A barrier designed to reduce the risk of

burns from the hot viewing glass is provided
with this appliance and shall be installed for

the protection of children and other at-risk

individuals.

Models:

EXCURSION-I
EXCURSION-II
EXCURSION-III

2

Quadra-Fire • EXCURSION-I, EXCURSION-II, EXCURSION-III Owner’s Manual • 2538-981 Rev. B • 2/19

Read this manual before operating this appliance.

Please retain this Owner’s Manual for future reference.

Read the Installation Manual before making any installation or nishing changes.

1

Welcome

A. Congratulations

Congratulations on selecting a Quadra-Fire gas replace,
an elegant and clean alternative to wood burning replaces.

The Quadra-Fire gas fireplace you have selected is
designed to provide the utmost in safety, reliability, and

efciency.

As the owner of a new replace, you’ll want to read and

carefully follow all of the instructions contained in this
Owner’s Manual. Pay special attention to all cautions and

warnings.

This Owner’s Manual should be retained for future

reference. We suggest that you keep it with your other

important documents and product manuals.

The information contained in this Owner’s Manual, unless
noted otherwise, applies to all models and gas control
systems.

Your new Quadra-Fire gas replace will give you years of
durable use and trouble-free enjoyment. Welcome to the
Quadra-Fire family of replace products!

Listing Label Information/Location

Model Name: ___________________________________________ Date purchased/installed: __________________

Serial Number: __________________________________________ Location on replace: _____________________

Dealership purchased from: _______________________________ Dealer Phone: __________________________

Notes: _______________________________________________________________________________________

_____________________________________________________________________________________________

We recommend that you record the following pertinent

information about your replace.

Gas and Electric
Information

Serial Number

Type of Gas

The model information regarding your specic replace can be found on

the rating plate located on the left side of the appliance outer wrap.

Homeowner Reference Information

Model Number

Not for use with solid fuel.
(Ne doit pas entre utilise avec un combustible solide).

This appliance must be installed in accordance with local codes, if any; if not, follow ANSI Z223.1
in the USA or CAN/CGA B149 installation codes. (Installer l’appareil selon les codes ou reglements

locaux ou, en l’absence de tels reglements, selon les codes d’installation

Type of Gas (Sorte De Gaz):

NATURAL GAS

MADE MADE IN IN USAUSA

Minimum Minimum Permissible Permissible

Quadra-Fire, a brand of Hearth & Home Technologies
7571 215th Street West, Lakeville, MN 55044

Gas Gas Supply Supply for for Purposes Purposes of of Input Input Adjustment.Adjustment.

Approved Approved Minimum Minimum (De (De Gaz) Gaz) AcceptableAcceptable 0.00.0 in in w.c.w.c. (Po. (Po. Col. Col. d’eau)d’eau)

Maximum Maximum Pressure Pressure (Pression)(Pression) 0.00.0 in in w.c.w.c. (Po. (Po. Col. Col. d’eau)d’eau)

Maximum Maximum Manifold Manifold Pressure Pressure (Pression)(Pression) 0.00.0 in in w.c.w.c. (Po. (Po. Col. Col. d’eau)d’eau)

Minimum Minimum Manifold Manifold Pressure Pressure (Pression)(Pression) 0.00.0 in in w.c.w.c. (Po. (Po. Col. Col. d’eau)d’eau)

Model:Model:

(Modele):(Modele):

SerialSerial

(Serie):(Serie):

ANSI Z21XX-XXXX · CSA 2.XX-MXX

XXXXXXXXXXXXXXXX

IN IN CANADACANADA
ALTITUDE:ALTITUDE: 0-0000 0-0000 FT.FT. 0000-0000FT.0000-0000FT.
MAX. MAX. INPUT INPUT BTUH:BTUH: 00,00000,000 00,00000,000
MIN. MIN. INPUT INPUT BTUH:BTUH: 00,00000,000 00,00000,000
ORIFICE ORIFICE SIZE:SIZE: #XXXXX#XXXXX #XXXXX#XXXXX

XXXXXXXXXXXXXXXX

Total Total Electrical Electrical Requirements: Requirements: 000Vac, 000Vac, 00Hz., less than 00 Amperes

R

3

Quadra-Fire • EXCURSION-I, EXCURSION-II, EXCURSION-III Owner’s Manual • 2538-981 Rev. B • 2/19

Safety Alert Key:

• DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury.

• WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.

• CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

• NOTICE: Used to address practices not related to personal injury.

Table of Contents

1 Welcome

A. Congratulations ................................. 2

B. Limited Lifetime Warranty .......................... 4

2 Product Specic Information

A. Appliance Certication ............................6

B. Glass Specications ..............................6

C. BTU Specications ............................... 6

3 Important Safety and Operating Information

A. Appliance Safety ................................ 7

B. General Operating Parts .......................... 8

C. Fuel Specications ............................... 8

D. Wall Surface/TV Guidelines ........................8

E. Before Lighting Appliance. . . . . . . . . . . . . . . . . . . . . . . . . 10

F. Lighting Instructions (IPI) ......................... 11

G. Appliance Break-In .............................. 12

H. Heat Management ..............................13

I. Operation During A Power Outage .................. 13

J. Detailed Component Operating Instructions - IntelliFire™

Touch ........................................ 14

4 Maintenance and Service

A. Maintenance: Frequency and Tasks ................ 16

B. Maintenance Tasks - Homeowner .................. 16

C. Maintenance Tasks - Qualied Service Technician .....19

5 Frequently Asked Questions and Troubleshooting

A. Frequently Asked Questions ......................21

B. Frequently Asked Questions - IntelliFire™ Touch Controls

(IFT-RC400) ...................................22

C. Troubleshooting ................................23

6 Reference Materials

A. Accessories ...................................25

B. Service Parts .................................. 26

C. Contact Information ............................. 34

 = Contains updated information.

4

Quadra-Fire • EXCURSION-I, EXCURSION-II, EXCURSION-III Owner’s Manual • 2538-981 Rev. B • 2/19

B. Limited Lifetime Warranty

X Molded refractory panels

4021-645H 10/15 Page 1 of 2

Hearth & Home Technologies

LIMITED LIFETIME WARRANTY

Hearth & Home Technologies, on behalf of its hearth brands (“HHT”), extends the following warranty for HHT
gas, wood, pellet, coal and electric hearth appliances that are purchased from an HHT authorized dealer.

WARRANTY COVERAGE:

HHT warrants to the original owner of the HHT appliance at the site of installation, and to any transferee taking ownership
of the appliance at the site of installation within two years following the date of original purchase, that the HHT appliance
will be free from defects in materials and workmanship at the time of manufacture. After installation, if covered compo­nents manufactured by HHT are found to be defective in materials or workmanship during the applicable warranty period,
HHT will, at its option, repair or replace the covered components. HHT, at its own discretion, may fully discharge all of its
obligations under such warranties by replacing the product itself or refunding the verified purchase price of the product
itself. The maximum amount recoverable under this warranty is limited to the purchase price of the product. This warranty
is subject to conditions, exclusions and limitations as described below.

WARRANTY PERIOD:

Warranty coverage begins on the date of original purchase. In the case of new home construction, warranty coverage
begins on the date of first occupancy of the dwelling or six months after the sale of the product by an independent,
authorized HHT dealer/ distributor, whichever occurs earlier. The warranty shall commence no later than 24 months
following the date of product shipment from HHT, regardless of the installation or occupancy date. The warranty period for
parts and labor for covered components is produced in the following table.

The term “Limited Lifetime” in the table below is defined as: 20 years from the beginning date of warranty coverage for
gas appliances, and 10 years from the beginning date of warranty coverage for wood, pellet, and coal appliances. These
time periods reflect the minimum expected useful lives of the designated components under normal operating conditions.

See conditions, exclusions, and limitations on next page.

Parts Labor Gas Wood Pellet

EPA

Wood

Coal Electric Venting

XXXXXXX

All parts and material except as

covered by Conditions,

Exclusions, and Limitations

listed

XXX

Igniters, electronic components,

and glass

X X X X X Factory-installed blowers

X Firepots and burnpots

5 years 1 year X X Castings and baffles

7 years 3 years X X X

Manifold tubes,

HHT chimney and termination

10

years

1 year X Burners, logs and refractory

Limited

Lifetime

3 years X X X X X Firebox and heat exchanger

XXXXXXX

All replacement parts

beyond warranty period

Warranty Period HHT Manufactured Appliances and Venting

1 Year

Components Covered

3 years

2 years

90 Days

X

Ignition Modules

5

Quadra-Fire • EXCURSION-I, EXCURSION-II, EXCURSION-III Owner’s Manual • 2538-981 Rev. B • 2/19

WARRANTY CONDITIONS:

• This warranty only covers HHT appliances that are purchased through an HHT authorized dealer or distributor. A list of
HHT authorized dealers is available on the HHT branded websites.

• This warranty is only valid while the HHT appliance remains at the site of original installation.

• This warranty is only valid in the country in which the HHT authorized dealer or distributor that sold the appliance
resides.

• Contact your installing dealer for warranty service. If the installing dealer is unable to provide necessary parts, contact
the nearest HHT authorized dealer or supplier. Additional service fees may apply if you are seeking warranty service
from a dealer other than the dealer from whom you originally purchased the product.

• Check with your dealer in advance for any costs to you when arranging a warranty call. Travel and shipping charges
for parts are not covered by this warranty.

This warranty is void if:

• The appliance has been over-fired or operated in atmospheres contaminated by chlorine, fluorine, or other damaging
chemicals. Over-firing can be identified by, but not limited to, warped plates or tubes, rust colored cast iron, bubbling,
cracking and discoloration of steel or enamel finishes.

• The appliance is subjected to prolonged periods of dampness or condensation.

• There is any damage to the appliance or other components due to water or weather damage which is the result of, but
not limited to, improper chimney or venting installation.

LIMITATIONS OF LIABILITY:

• The owner’s exclusive remedy and HHT’s sole obligation under this warranty, under any other warranty, express or
implied, or in contract, tort or otherwise, shall be limited to replacement, repair, or refund, as specified above. In no
event will HHT be liable for any incidental or consequential damages caused by defects in the appliance. Some states
do not allow exclusions or limitation of incidental or consequential damages, so these limitations may not apply to you.
This warranty gives you specific rights; you may also have other rights, which vary from state to state. EXCEPT TO
THE EXTENT PROVIDED BY LAW, HHT MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY
SPECIFIED HEREIN. THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO DURATION OF THE
EXPRESSED WARRANTY SPECIFIED ABOVE.

WARRANTY EXCLUSIONS:

This warranty does not cover the following:

• Changes in surface finishes as a result of normal use. As a heating appliance, some changes in color of interior and
exterior surface finishes may occur. This is not a flaw and is not covered under warranty.

• Damage to printed, plated, or enameled surfaces caused by fingerprints, accidents, misuse, scratches, melted items,
or other external sources and residues left on the plated surfaces from the use of abrasive cleaners or polishes.

• Repair or replacement of parts that are subject to normal wear and tear during the warranty period. These parts
include: paint, wood, pellet and coal gaskets, firebricks, grates, flame guides, batteries and the discoloration of glass.

• Expansion, contraction, or movement of certain parts causing noise. These conditions are normal and complaints
related to this noise are not covered by this warranty.

• Damages resulting from: (1) failure to install, operate, or maintain the appliance in accordance with the installation
instructions, operating instructions, and listing agent identification label furnished with the appliance; (2) failure to
install the appliance in accordance with local building codes; (3) shipping or improper handling; (4) improper opera­tion, abuse, misuse, continued operation with damaged, corroded or failed components, accident, or improperly/
incorrectly performed repairs; (5) environmental conditions, inadequate ventilation, negative pressure, or drafting
caused by tightly sealed constructions, insufficient make-up air supply, or handling devices such as exhaust fans or
forced air furnaces or other such causes; (6) use of fuels other than those specified in the operating instructions; (7)
installation or use of components not supplied with the appliance or any other components not expressly authorized
and approved by HHT; (8) modification of the appliance not expressly authorized and approved by HHT in writing;
and/or (9) interruptions or fluctuations of electrical power supply to the appliance.

• Non-HHT venting components, hearth components or other accessories used in conjunction with the appliance.

• Any part of a pre-existing fireplace system in which an insert or a decorative gas appliance is installed.

• HHT’s obligation under this warranty does not extend to the appliance’s capability to heat the desired space. Informa­tion is provided to assist the consumer and the dealer in selecting the proper appliance for the application. Consider­ation must be given to appliance location and configuration, environmental conditions, insulation and air tightness of
the structure.

4021-645H 10/15 Page 2 of 2

6

Quadra-Fire • EXCURSION-I, EXCURSION-II, EXCURSION-III Owner’s Manual • 2538-981 Rev. B • 2/19

A. Appliance Certication

2

Product Specic Information

This product is listed to ANSI standards for “Vented Gas
Fireplace Heaters” and applicable sections of “Gas Burn­ing Heating Appliances for Manufactured Homes and
Recreational Vehicles”, and “Gas Fired Appliances for
Use at High Altitudes”.

Quadra-Fire gas inserts are designed for installations into

solid fuel masonry or factory built replaces that have been

installed in accordance with the National, Provincial, State
and local building codes. Fireplaces are to be constructed
of non-combustible materials and, in the absence of local
or regional codes, meet criteria of NFPA 211. No additional
outside air source is required.

NOT INTENDED FOR USE AS A PRIMARY HEAT SOURCE.

This appliance is tested and approved as either supplemen­tal room heat or as a decorative appliance. It should not be
factored as primary heat in residential heating calculations.

NOTICE: This installation must conform with local codes.

In the absence of local codes you must comply with the

National Fuel Gas Code, ANSI Z223.1-latest edition in
the U.S.A. and the CAN/CGA B149 Installation Codes in
Canada.

B. Glass Specications

This appliance is equipped with 5 mm ceramic glass. Re­place glass only with 5 mm ceramic glass. Please contact
your dealer for replacement glass.

C. BTU Specications

MODELS: EXCURSION-I, EXCURSION-II,

EXCURSION-III

LABORATORY: Underwriters Laboratories, Inc. (UL)

TYPE: Direct Vent Heater

STANDARD: ANSI Z21.88-2017 CSA 2.33-2017

Models

(U.S. or Canada)

Maximum

Input

BTU/h

Minimum

Input

BTU/h

Orice

Size

(DMS)

EXCURSION-I

(NG)

(0-2000 FT) 27,000 18,900 40

EXCURSION-I

(Propane)

(0-2000 FT) 25,000 17,500 53

EXCURSION-II

(NG)

(0-2000 FT) 32,700 22,890 35

EXCURSION-II

(Propane)

(0-2000 FT) 32,000 22,400 51

EXCURSION-III

(NG)

(0-2000 FT) 35,000 24,500 33

EXCURSION-III

(Propane)

(0-2000 FT) 35,000 24,500 50

Installation and service of this appliance should be performed by

qualied personnel. Hearth & Home Technologies recommends
HHT Factory Trained or NFI certied professionals.

7

Quadra-Fire • EXCURSION-I, EXCURSION-II, EXCURSION-III Owner’s Manual • 2538-981 Rev. B • 2/19

WARNING! DO NOT operate replace before reading
and understanding operating instructions. Failure

to operate replace according to operating instructions
could cause re or injury.

Young children should be carefully supervised when they
are in the same room as the appliance. Toddlers, young
children and others may be susceptible to accidental
contact burns.

• A physical barrier is recommended if there are at risk

individuals in the house.

• To restrict access to a replace or stove, install an

adjustable safety gate to keep toddlers, young children
and other at risk individuals out of the room and away

from hot surfaces.

• Install a switch lock or a wall/remote control with child

protection lockout feature.

• Keep remote controls out of reach of children.

• Never leave children alone near a hot replace, whether

operating or cooling down.

A. Appliance Safety

• Teach children to NEVER touch the replace.

• Consider not using the replace when children will be

present.

Contact your dealer for more information, or visit: www.
hpba.org/Product-Info/Fireplace-Stove-Heater/Glass­Fronts-Safety.

To prevent unintended operation when not using your re­place for an extended period of time (summer months,
vacations, trips, etc):

• Remove batteries from remote controls.

• Turn off wall controls.

• Set the selector switch on the control module to the off
position and remove batteries.

3

Important Safety and Operating Information

Clear Space

WARNING! DO NOT place combustible objects in front

of the replace or block louvers. High temperatures may
start a re. See Figure 3.1.

Avoid placing candles and other heat-sensitive objects on
mantel or hearth. Heat may damage these objects.

Figure 3.1 Clear Space Requirement - All Models

CLEAR SPACE

3 FT. IN

FRONT OF

FIREPLACE

A barrier designed to reduce the risk of burns from the
hot viewing glass is provided with this appliance and
shall be installed for the protection of children and other
at-risk individuals. DO NOT operate the appliance with
the barrier removed. If the barrier becomes damaged,
the barrier shall be replaced with the manufacturer’s
barrier for this appliance.

Contact your dealer or Hearth & Home Technologies if the

barrier is not present or help is needed to properly install one.

DANGER

HOT GLASS WILL

CAUSE BURNS.

DO NOT TOUCH GLASS

UNTIL COOLED.

NEVER ALLOW CHILDREN

TO TOUCH GLASS.

• Keep children away.

• CAREFULLY SUPERVISE children in same room

as replace.

• Alert children and adults to hazards of high
temperatures.

High temperatures may ignite clothing or other

ammable materials.

• Clothing, furniture, draperies, and other ammable

materials must not be placed on or near the
appliance.

WARNING: This product and the fuels used to
operate this product (liquid propane or natural

gas), and the products of combustion of such fuels, can
expose you to chemicals including benzene, which is

known to the State of California to cause cancer and

reproductive harm. For more information go to: www.
P65Warnings.ca.gov.

8

Quadra-Fire • EXCURSION-I, EXCURSION-II, EXCURSION-III Owner’s Manual • 2538-981 Rev. B • 2/19

Figure 3.2 General Operating Parts

B. General Operating Parts

C. Fuel Specications

Figure 3.2 references the general operating parts of the
appliance and the section of this manual in which they are
discussed.

WARNING! Risk of Fire or Explosion! Appliance must
be set up for compatible gas type!

• This appliance is designed to operate on either natural

gas or propane. Make sure the appliance is compatible

with gas type selected for installation site.

• Conversions must be made by a qualified service

technician using Hearth & Home Technologies specied

and approved parts.

D. Wall Surface/TV Guidelines

DECORATIVE FRONTS

(NOT SHOWN)

SECTION 4.B

MANTEL

FIXED GLASS ASSEMBLY

SECTION 4.B

HEARTH

CLEAR SPACE

SECTION 3.A.

ACCESS TO

BATTERY BACKUP

SECTION 3.I

FAN KIT

SECTION 3.H & 3.J

REMOTE CONTROL

SECTION 6.C

Figure 3.3 Good Faith Wall Surface Temperatures Above Appliance

NOTICE: Temperatures listed above are taken with a

temperature measuring probe as prescribed by the test

standard used for appliance certication. Temperatures
on walls or mantels taken with an infrared thermometer

may yield increased temperatures of up to 30 degrees or
more depending on the thermometer settings and material

characteristics being measured. Use appropriate nishing
materials that are able to withstand these conditions. For
additional nishing guidelines, see Section 8 Installation
Manual.

MEASUREME NTS FROM TOP

OF THE SUR ROUND OPENING

CEILING

APPLIANCE SURROU ND

SURROUND
OPENING

18 IN.

22 IN.

16 IN.

12 IN.

24 IN.

28 IN.

34 IN.

40 IN.

46 IN.

52 IN.

151 ºF

138 ºF

135 ºF

127 ºF

125 ºF

120 ºF

115 ºF

110 ºF

108 ºF

106 ºF

9

Quadra-Fire • EXCURSION-I, EXCURSION-II, EXCURSION-III Owner’s Manual • 2538-981 Rev. B • 2/19

Item Minimum Dimensions

A 2.5 inches

B

2 inches minimum to 3 inches
maximum

C 24 inches

D

Wall Brkt + TV Thickness + 2.5
inches

B

Fireplace

TV

Mantel

A

C

TV Wall
Bracket

D

TV on the wall

Notes:

1. These are good faith recommended clearances only and not a guarantee of compliance with all TV
manufacturers’ maximum allowable opera

ng temperatures.

2. Since every home has unique air ow characteris

cs and maximum allowable opera ng temperatures
can vary from manufacturer to manufacturer and from model to model, actual TV temperatures should
be validated at the

me of each installa on. TVs should not be used in situa ons where the actual TV

temperature exceeds the manufacturers’ maximum allowable opera

ng temperatures iden ed in the

TV’s technical specica

ons. Contact the TV’s manufacturer directly if you cannot locate this

informa

on or have ques ons regarding the informa

on.

3. Mantel height and depth must conform to mantle requirements specified in the replace installa

on

manual.

4.

“C” dimension taken from the top of the hood or fireplace opening.

5.

Sugges ons on how to further reduce TV temperatures:

a. Increase “A” dimension.

b.

Increase “C” dimension, however, increasing “B” dimension beyond maximum recommended
typically results in higher temperatures.

Good Faith Guidelines for TV Installations above a Typical Gas Fireplace

Top of Surround
Opening

Figure 3.4 Good Faith TV Guidelines

10

Quadra-Fire • EXCURSION-I, EXCURSION-II, EXCURSION-III Owner’s Manual • 2538-981 Rev. B • 2/19

E. Before Lighting Appliance

Before operating this replace for the rst time, have a

qualied service technician:

• Verify all shipping materials have been removed from

inside and/or underneath the rebox.

• Review proper placement of logs, ember material and/
or other decorative materials.

• Check the wiring.

• Check the air shutter adjustment.

• Ensure that there are no gas leaks.

• Verify Glass Seal Plate is properly installed. See Figure

3.6.

WARNING! Glass seal plate must be properly installed.
Risk of elevated component temps and carbon monox­ide exposure.

• Ensure that the glass is sealed and in the proper position
and that the integral barrier is in place.

WARNING! Risk of Fire or Asphyxiation! DO NOT op­erate replace with xed glass assembly removed.

• Verify collar slide plate screw is attached see Figure 3.5.

Figure 3.5 Collar slide Plate Screw Detail

BE SURE SLIDE
PLATE SCREW IS
FULLY TIGHTENED.

11

Quadra-Fire • EXCURSION-I, EXCURSION-II, EXCURSION-III Owner’s Manual • 2538-981 Rev. B • 2/19

F. Lighting Instructions (IPI)

FOR YOUR SAFETY READ BEFORE LIGHTING

TO TURN OFF GAS TO APPLIANCE

1. This appliance is equipped with an ignition device which
automatically lights the burner. DO NOT try to light the burner by hand.

1. Equipped with wall switch: Turn ON/OFF switch to OFF.
Equipped with remote or wall control: Press OFF button.
Equipped with thermostat: Set temperature to lowest setting.

WARNING

WARNING:

NOT FOR USE WITH SOLID FUEL

GAS

VALVE

For additional information on operating your

refer to www.hearthnhome.com.

A. This appliance is equipped with an intermittent pilot ignition (IPI) device which

automatically lights the burner. DO NOT try to light the burner by hand.

B. BEFORE LIGHTING, smell all around the appliance area for gas. Be sure to smell

WHAT TO DO IF YOU SMELL GAS

• DO NOT try to light any appliance.

• DO NOT touch any electric switch; do not use any phone in your building.

DO NOT CONNECT LINE VOLTAGE (110/120 VAC OR 220/240 VAC) TO THE CON­TROL VALVE.

Improper installation, adjustment, alteration, service or maintenance can cause injury
or property damage. Refer to the owner’s information manual provided with this ap-

agency or the gas supplier.

This appliance needs fresh air for safe operation and must be installed so there are
provisions for adequate combustion and ventilation air.

Hot while in operation. DO NOT touch. Keep children, clothing, furniture, gasoline

DO NOT operate the appliance with removed, cracked or
broken. Replacement of the

should be done by a licensed or

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas sup­plier’s instructions.

•

C. Use only your hand to push in or turn the gas control knob. Never use tools. If

the knob will not push in or turn by hand, DO NOT

D. DO NOT use this appliance if any part has been under water. Immediately call

the control system and any gas control which has been under water.

For use with natural gas and propane. A conversion kit, as supplied by the manufac­turer, shall be used to convert this appliance to the alternate fuel.

This appliance must be installed in accordance with local codes, if any; if none,
follow the National Fuel Gas Code, ANSIZ223.1/ NFPA 54, or the National Gas and

Propane Installation code, CSA B149.1.

LIGHTING INSTRUCTIONS (IPI)

2.

top of this label. If you do not smell gas, go to next step.

3. To light the burner:

Equipped with wall switch: Turn ON/OFF switch to ON.
Equipped with remote or wall control: Press ON or FLAME button.

Equipped with thermostat: Set temperature to desired setting.

4. If the appliance does not light after three tries, call your service technician or gas

supplier.

2. Service technician should turn off electric power to the control when performing

service.

DANGER

HOT GLASS WILL CAUSE BURNS.

DO NOT TOUCH GLASS UNTIL COOLED.

NEVER ALLOW CHILDREN TO TOUCH GLASS.

CAUTION:

A barrier designed to reduce the risk of burns from the hot viewing glass is provided with this
appliance and shall be installed for the protection of children and other at-risk individuals.

WARNING: This product and the fuels used to operate this
product (liquid propane or natural gas), and the products

of combustion of such fuels, can expose you to chemicals
including benzene, which is known to the State of California to cause
cancer and reproductive harm. For more information go to: www.
P65Warnings.ca.gov.

Keep burner and control compartment clean. See installation and operating instructions
accompanying appliance.