QSC Q-SYS DCIO-H, Q-SYS DCIO Hardware User's Manual

™

®

Hardware User Guide

Digital Cinema I/O — DCIO-H

Digital Cinema I/O — DCIO

TD-001532-01-A

*TD-001532-01*

EXPLANATION OF TERMS AND SYMBOLS

The term “WARNING!” indicates instructions regarding personal safety. If the instructions are not followed the result may be bodily injury or death.

The term “CAUTION!” indicates instructions regarding possible damage to physical equipment. If these instructions are not followed, it may result in
damage to the equipment that may not be covered under the warranty.

The term “IMPORTANT!” indicates instructions or information that are vital to the successful completion of theprocedure.

The term "NOTE" is used to indicate additional useful information.

The intent of the lightning flash with arrowhead symbol in a triangle is to alert the user to the presence of un-insulated "dangerous"
voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to humans.

The intent of the exclamation point within an equilateral triangle is to alert the user to the presence of important safety, and operating
and maintenance instructions in this manual.

IMPORTANT SAFETY INSTRUCTIONS

WARNING!: TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN
OR MOISTURE.

• Elevated Operating Ambient - If installed in a closed or multi-unit rack assembly, the ambient operating temperature of
the rack environment may be greater than room ambient. Consideration should be given to ensure that the maximum operating
temperature range (0°C to 50°C (32°F to 122°F ) is not exceeded.

• Reduced Air Flow – Installation of the equipment in a rack should be such that the amount of air flow required for safe
operation of the equipment is not compromised.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Do not submerge the apparatus in water or liquids.

7. Do not use any aerosol spray, cleaner, disinfectant or fumigant on, near or into the apparatus.

8. Clean only with a dry cloth.

9. Do not block any ventilation opening. Install in accordance with the manufacturer's instructions.

10. Keep all ventilation openings free of dust or other matter.

11. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

12. To reduce the risk of electrical shock, the power cord shall be connected to a mains socket outlet with a protective earthing connection.

13. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A
grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

14. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from
theapparatus.

15. Do not unplug the unit by pulling on the cord, use the plug.

16. Only use attachments/accessories specified by the manufacturer.

17. Unplug this apparatus during lightning storms or when unused for long periods of time.

18. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as
power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been dropped.

19. The appliance coupler, or the AC Mains plug, is the AC mains disconnect device and shall remain readily accessible after installation.

20. Adhere to all applicable, local codes.

21. Consult a licensed, professional engineer when any doubt or questions arise regarding a physical equipment installation.

TD-001532-01-A

2

Maintenance and Repair

WARNING!: Advanced technology, e.g., the use of modern materials and powerful electronics,
requires specially adapted maintenance and repair methods. To avoid a danger of subsequent
damage to the apparatus, injuries to persons and/or the creation of additional safety hazards, all
maintenance or repair work on the apparatus should be performed only by a QSC authorized service
station or an authorized QSC International Distributor. QSC is not responsible for any injury, harm or
related damages arising from any failure of the customer, owner or user of the apparatus to facilitate
those repairs.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own expense.

IMPORTANT!: The Q-SYS DCIO may operate at elevated temperatures and therefore its exterior may become noticeably
warm. This is normal. The Q-SYS DCIO is designed with convection cooling in mind and therefore incorporates industrial
high-temp components to accommodate higher operating temperatures.

Expected Product Life Cycle: 20 years, Storage Temperature range: -20°C to + 70°C, Relative Humidity range: of
5–85% RH non-condensing.

RoHS STATEMENT

The QSC Q-SYS DCIO is in compliance with European Directive 2011/65/EU – Restriction of Hazardous Substances(RoHS2).
The QSC Q-SYS DCIO is in compliance with “China RoHS” directives. The following chart is provided for product use in China and its territories:

QSC Q-SYS DCIO

部件名称

(Part Name)

铅

(Pb)

电路板组件

(PCB Assemblies)

机壳装配件

(Chassis

Assemblies)

本表格依据 SJ/T 11364 的规定编制。
O: 表示该有害物质在该部件所有均质材料中的含量均在 GB/T 26572 规定的限量要求以下。
X: 表示该有害物质至少在该部件的某一均质材料中的含量超出 GB/T 26572 规定的限量要求。 （目前由于技术或经济的

原因暂时无法实现替代或减量化。）
This table is prepared following the requirement of SJ/T 11364.

O: Indicates that the concentration of the substance in all homogeneous materials of the part is below the relevant
threshold speci󽗉ed in GB/T 26572.
X: Indicates that the concentration of the substance in at least one of all homogeneous materials of the part is
above the relevant threshold speci󽗉ed in GB/T 26572.
(Replacement and reduction of content cannot be achieved currently because of the technical or economic reason.)

X O O O O O

X O O O O O

汞

(Hg)

(Hazardous Substances)

镉

(Cd)

有害物质

六价铬
(Cr(vi))

多溴联苯

(PBB)

多溴二苯醚

(PBDE)

TD-001532-01-A

3

Warranty

For a copy of the QSC Limited Warranty, visit the QSC, LLC. website at www.qsc.com

Para una copia de la Garantía Limitada de QSC, visite el sitio web de QSC, LLC., en www.qsc.com Pour obtenir une copie de la garantie limitée de
QSC, visitez le site de QSC, LLC.à www.qsc.com

Besuchen Sie die Webseite von QSC, LLC. (www.qsc.com) um eine Kopie der beschränkten Garantie von QSC zu erhalten.

如果您想要QSC有限保修的複印本，请造访QSC音频产品的网站www.qsc.com

Для получения копии ограниченной гарантии QSC посетите веб-сайт QSC, LLC., расположенный по
адресу www.qsc.com.

للحصول على نسخة من الضمان المحدود الخاص بـQSC، قم بزيارة الموقع اإللكتروني لشركة QSC للمنتجات الصوتية

على www.qsc.com

QSC限定保証の複製には、QCSのウェブサイトwww.qsc.comにアクセスしてください。

TD-001532-01-A

4