QSC DCP 200, DCP 300, DCP 100 Owner's Manual

4 (1)

DCP Series

Digital Cinema Hardware User Manual

DCP – Digital Cinema Processor

TD-000285-00 C

*TD-000285-00*

IMPORTANT SAFETY PRECAUTIONS AND EXPLANATION OF SYMBOLS

WARNING!

The lightning ﬂash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous” voltage within the product’s enclosure that may be of sufﬁcient magnitude to constitute a risk of electric shock to humans.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in this manual.

SAFEGUARDS

Electrical energy can perform many useful functions. This unit has been engineered and manufactured to assure your personal safety. Improper use can result in potential electrical shock or ﬁre hazards. In order not to defeat the safeguards, observe the following instructions for its installation, use and servicing.

Caution: To reduce the risk of electric shock, do not remove the cover. No user-serviceable parts inside. Refer servicing to qualiﬁed service personnel.

Warning: To prevent ﬁre or electric shock, do not expose this equipment to rain or moisture.

1. Maximum operating ambient temperature is 50°C (122°F).

2. Never restrict airﬂow through the device vents. Please insure that the side panel vents are unobstructed.

3. When installing equipment into a rack, distribute the units evenly. Otherwise, hazardous conditions could be created by an uneven distribution of weight.

4. Connect the unit only to a properly rated supply circuit. The DCP is suitable for connection to 100-240VAC, 50-60Hz with no special considerations other than the appropriate IEC power cord.

5. Reliable earthing (grounding) of rack-mounted equipment should be maintained.

LITHIUM BATTERY WARNING

THE DCP EQUIPMENT CONTAINS A NON-RECHARGEABLE LITHIUM BATTERY. LITHIUM IS A CHEMICAL KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER OR BIRTH DEFECTS. THE NON-RECHARGEABLE LITHIUM BATTERY CONTAINED IN THIS EQUIPMENT MAY EXPLODE IF IT IS EXPOSED TO FIRE OR EXTREME HEAT. DO NOT SHORT CIRCUIT THE BATTERY. DO NOT ATTEMPT TO RECHARGE THE NON-RECHARGEABLE LITHIUM BATTERY.

Warranty (USA only; other countries, see your dealer or distributor)

Disclaimer

QSC Audio Products, LLC (“QSC”) is not liable for any damage to amplifiers, loudspeakers, or other equipment that is caused by negligence or improper installation and/or use of this signal processing product. While QSC has endeavored to develop and produce the most dependable and robust ‘network’ audio product for your use, due to the myriad of network situations and equipment that may be encountered in its implementation, QSC cannot be held responsible for network conflicts and associated consequences that may result. For this reason, QSC strongly recommends that the network used for implementation of the DCP product(s) be completely separate from all other networks, data or otherwise. As such, should you elect to integrate the DCP product(s) with an existing network system, all risks attendant to such integration of the DCP product(s) with an existing network or network systems are assumed by you. While QSC strives to provide the highest quality technical solutions for networked audio products, in no event will QSC or its suppliers be held liable for any damage, consequential, incidental or otherwise, including any claims for lost profits and/or savings resulting from any attempted integration of the DCP product(s) with an existing network or network system. No agent, employee or representative of QSC has any authority to alter or modify in any manner, the disclosures and recommendations set forth herein.

QSC Audio Products 3-Year Limited Warranty

QSC Audio Products, LLC (“QSC”) guarantees the DCP 100, 200, and 300 products to be free from defective materials and/or workmanship for a period of three (3) years from the date of sale and will replace defective parts and repair malfunctioning products under this warranty when the defect occurs under normal installation and use – provided the unit is returned to our factory or one of our authorized service stations via prepaid transportation with a copy of proof of purchase (i.e., sales receipt). This warranty provides that the examination of the returned product must indicate, in our judgment, a manufacturing defect. This warranty does not extend to any product which has been subjected to misuse, neglect, accident, improper installation, or where the date code has been removed or defaced. QSC shall not be liable for incidental and/or consequential damages. This warranty gives you specific legal rights. This limited warranty is freely transferable during the term of the warranty period.

Customers may have additional rights, which vary from state to state or from country to country. In the event that a provision of this limited warranty is void, prohibited or superseded by local laws, the remaining provisions shall remain in effect.

Periodically, this warranty is updated. To obtain the most recent version of QSC’s warranty statement, please visit www.qscaudio.com.

The QSC limited warranty is valid for a period of three (3) years from date of purchase in the United States and many (but not all) other countries.

For QSC warranty information in countries other than the United States, contact your authorized QSC international distributor. A list of QSC International distributors is available at www.qscaudio.com.

To register your QSC product online, go to www.qscaudio.com and select ”Product Registration”. Other questions regarding this warranty can be answered by calling, e-mailing or contacting your authorized QSC distributor.

© 2010, QSC Audio Products, LLC. Patents may apply or be pending. QSC is a registered trademark of QSC Audio Products, LLC. “QSC” and the QSC logo are registered with the U.S. Patent and Trademark Ofﬁce. All trademarks are the property of their respective owners.

FCC Interference Statement

NOTE: This equipment has been tested and found to be in compliance with the limits for a class B digital device, pursuant to part 15 of the FCC rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by switching the equipment on and off, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio or TV technician for help.

RoHS Statement

The DCP products are in compliance with European Directive 2002/95/EC – Restriction of Hazardous Substances (RoHS). The DCP products are in compliance with “China RoHS” directives. The following chart is provided for product use in China and its territories:

DCP 100, 200, 300 系列

有毒有害物质或元素

部件名称

(Part Name)

电路板组件

(PCB Assemblies)

机壳装配件

(Chassis Assemblies)

O: 表明这些有毒或有害物质在部件使用的同类材料中的含量是在 SJ/T11363_2006极限的要求之下。

O: Indicates that this toxic or hazardous substance contained in all of the homogeneous materials for this part is below the limit requirement in SJ/ T11363-2006.

X: 表明这些有毒或有害物质在部件使用的同类材料中至少有一种而含量是在SJ/T11363_2006极限的要求之上。

X: Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials used for this part is above the limit requirement in SJ/T11363-2006.

铅

(Pb)

X O O O O O

O O X O O O

汞

(Hg)

(Toxic or hazardous Substances and Elements )

镉

(Cd)

六价铬

(Cr(vi))

多溴联苯

(PBB)

多溴二苯醚

(PBDE)

Introduction

QSC’s DCP is a powerful solution for today’s D-Cinema audio systems. From server to speakers, the DCP offers a complete set of tools to facilitate all the signal processing, audio distribution, monitoring and automation control services required in a modern D-Cinema sound system.

The DCP builds on the legacy of QSC’s DCM and BASIS™ products to provide all signal processing and monitoring functions for Digital Cinema in a single integrated system. Designed to be used with QSC’s Digital Cinema Ampliﬁers (DCA) and featuring advanced DSP presets for QSC’s Digital Cinema Speakers (DCS), the DCP optimizes loudspeaker performance while simplifying cinema sound system wiring and conﬁguration. The DCP covers cinema systems ranging from three to ﬁve screen channels, and is conﬁgurable for bi-amp, tri-amp or quad-amp operation. Though optimized to receive audio content directly from a D-Cinema server, the DCP is also compatible with all analog cinema processor formats including Dolby® Digital Surround-EX and DTS-ES and features a 10 channel analog input for integration with 35 mm audio systems.

The DCP is more than an audio processor. Whether designing a system for a single auditorium or designing a large multiplex, the DCP offers the ﬂexibility in conﬁguration, networking, audio distribution and advanced management services to get the job done.

Features

Selector Matrix

DCP 100 DCP 200 DCP 300

Digital Inputs 10 channel 16 channel 16 channel

Screen

Channel

Crossovers

• Digital inputs accept AES-3 audio from a D-Cinema server or other digital audio source

• Analog inputs accept audio from ﬁlm processors

• Additional analog inputs accommodate non-sync and Mic/Line sources

• Master volume and full 1/3 octave EQ on all channels (except subwoofer)

• Booth monitor with touch screen control for easy operation

• Digital loudspeaker crossovers

• Three or ﬁve screen channels with 2-way, 3-way or 4-way crossovers

• Compatible with all existing QSC DCA ampliﬁers

• Dual internal power supplies with load sharing for seamless recovery in the event of a failure

• SD memory card for quick unit swap – restores all settings

• Multiple bypass modes – routes audio around failed components to ensure that the show will go on

• DSP presets for QSC’s DCS speakers for great “out of the box” performance and reduced setup time

• QSControl.net™ software (including Venue Manager, QSCreator, Notify and API for 3rd Party control systems) offer ultimate ﬂexibility in

management and allow for the creation of custom control screens, remote access, fault reporting and diagnosis

Type 2 way — 2, 3, 4 way

Quantity 3 — 5

CobraNet™ No Yes Yes

• Easily integrates with existing ﬁlm processors for dual ﬁlm/digital projection systems

• CobraNet offers digital non-sync routing and future expansion capability (DCP 200 and DCP 300 models only)

• Continued development of software and ﬁrmware will add new capabilities via easy updates

Digital Signal Processing

The DCP digital signal processing capability outperforms traditional analog crossovers and equalizers for optimized speaker performance. Crossover frequency, 1/3 octave graphic EQ, parametric equalization, polarity, delay and gain can be precisely adjusted for each speaker in your system. Active 2-way, 3-way and 4-way crossovers are available. Advanced crossover presets for QSC DCS speakers speeds system set-up and ensures maximum performance.

Less Wiring, Faster Setup

The DCP greatly simpliﬁ es system wiring and setup, signiﬁ cantly reducing installation time and labor cost. Input to the DCP is provided via standard DB-25 cables from the D-Cinema server and/or 35 mm cinema processor. Connections to DCA ampliﬁ ers for input and monitor signals are made through a single QSC DataPort cable (VGA-style cable). All traditional XLR and barrier strip terminations are eliminated. DCP processors simplify setup by using a menu-driven, PC-based software program for conﬁ guration. The program includes a speaker data ﬁ le that lists default parameters for popular cinema speaker models. Commonly used conﬁ gurations can also be saved on a disk, or redistributed across a network, allowing you to quickly load them into other DCP processors throughout a theatre complex. All system conﬁ guration data may be saved to an SD memory card, allowing easy transfer of settings to a new (backup) DCP, should replacement ever be required.

Advanced Monitor Functions

In addition to audio monitoring of ampliﬁ er inputs and outputs, the DCP includes QSC’s exclusive “load fault” detection. The DCP monitors all ampliﬁ er outputs and indicates opens and shorts in the speaker system, providing conﬁ rmation that all ampliﬁ er outputs are functioning properly. Further, the DCP detects all ampliﬁ er clipping and protect modes and heat sink temperature for reporting via a QSControl™ Ethernet monitoring system or via SNMP.

The QSControl.net™ suite of applications allows for the creation of custom control screens via “drag and drop” design using the QSCreator software application. Screens can be designed to provide intuitive fault reporting and diagnosis that is accessible through remote network access. In addition, QSC’s PoE-enabled NAC 100 Ethernet remote control panel provides remote operation and status throughout a cinema multiplex from anywhere on the local network.

DCP 300 Front Panel Features

1. Power “on” switch

2. 4" full-range monitor speaker

3. Monitor volume and parameter adjust (function depends on operating mode)

Monitor mode: controls level to DCP front panel speaker in monitor mode Setup mode: provides parameter control in setup mode

4. Setup mode LED – illuminates green when DCP is in setup mode

5. Touch control LCD (4.3" 16:9 color display)

6. Fault LED – illuminates red when load faults or system errors are detected

7. Power “on” LED – illuminates green when AC power is applied

8. Mute button – illuminates red when engaged, illuminates green when disengaged

9. Auditorium volume control – global level control for all audio outputs

2 3 76

DCP 300 Rear Panel Features

1 2 9 10 115 6 7 8

1. Mono analog input – accepts microphone or line level signals (with phantom power)

2. Stereo analog inputs – accepts line level signals

3. Analog audio inputs – connect to D-Cinema server or ﬁ lm processor with analog outputs

• Top connector: channels 1 through 8

• Bottom connector: 6 auxiliary channels

4. Digital audio inputs – connect to D-Cinema server or ﬁ lm processor with digital outputs

• Top connector: AES3 pairs 1 through 4 (digital audio channels 1 through 8)

• Bottom connector: AES3 pairs 5 through 8 (digital audio channels 9 through 16)

3 4

17161513 1412

5. S/PDIF input – multi-channel digital input for non-sync/alternative content

6. USB Type B port for DCP conﬁ guration and management via direct connection

7. 10/100 Mbps Ethernet port – for QSControl™, 3rd party, or SNMP management and remote access

8. 100 Mbps Ethernet ports – CobraNet™ audio network - Primary and Secondary (backup)

9. SD memory card – device conﬁ guration storage supports quick unit replacement

10. Serial communications port – 3rd party control/automation via RS232

11. IEC inlet – AC mains power connector with cord lock

12. DataPort interface for QSC ampliﬁ ers – supports up to fourteen single port ampliﬁ ers

13. Hearing impaired and visually impaired special mix outputs

14. CMOS compatible logic outputs – for use as automation triggers, alerts, system status

15. Automation inputs – digitally sampled analog control inputs (control presets, levels etc.)

16. Relay outputs – mechanically decoupled control outputs (curtain, lighting control etc.)

17. Audio monitor output – tap from front panel monitor speaker (post DSP, pre ampliﬁ er)

DCP 200 Front Panel Features

2 3

1. Power “on” switch

2. 4" full-range monitor speaker

3. Monitor volume and parameter adjust (function depends on operating mode) Monitor mode: controls level to DCP front panel speaker in monitor mode Setup mode: provides parameter control in setup mode

4. Setup mode LED – illuminates green when DCP is in setup mode

5. Touch control LCD (4.3" 16:9 color display)

6. Fault LED – illuminates red when load faults or system errors are detected

7. Power “on” LED – illuminates green when AC power is applied

8. Mute button – illuminates red when engaged, illuminates green when disengaged

9. Auditorium volume control – global level control for all audio outputs

DCP 200 Rear Panel Features

1 2 9 10 115 6 7 8

1. Mono analog input – accepts microphone or line level signals (with phantom power)

2. Stereo analog inputs – accepts line level signals

3. Analog audio inputs – connect to D-Cinema server or ﬁlm processor with analog outputs

• Top connector: channels 1 through 8

• Bottom connector: 6 auxiliary channels

4. Digital audio inputs – connect to D-Cinema server or ﬁlm processor with digital outputs

3 4

17161513 1412

• Top connector: AES3 pairs 1 through 4 (digital audio channels 1 through 8)

• Bottom connector: AES3 pairs 5 through 8 (digital audio channels 9 through 16)

5. S/PDIF input – multi-channel digital input for non-sync/alternative content

6. USB Type B port for DCP conﬁguration and management via direct connection

7. 10/100 Mbps Ethernet port – for QSControl™, 3rd party, or SNMP management and remote access

8. 100 Mbps Ethernet ports – CobraNet™ audio network - Primary and Secondary (backup)

9. SD memory card – device conﬁguration storage supports quick unit replacement

10. Serial communications port – 3rd party control/automation via RS232

11. IEC inlet – AC mains power connector with cord lock

12. DataPort interface for QSC ampliﬁers – supports up to six single port ampliﬁers

13. Hearing impaired and visually impaired special mix outputs

14. CMOS compatible logic outputs – for use as automation triggers, alerts, system status

15. Automation inputs – digitally sampled analog control inputs (control presets, levels etc.)

16. Relay outputs – mechanically decoupled control outputs (curtain, lighting control etc.)

17. Audio monitor output – tap from front panel monitor speaker (post DSP, pre ampliﬁer)

+ 16 hidden pages