QSC CXD8.4Q, CXD8.8Qn, CXD8.8Q User Manual

Download

Page 1

CXD-Q Amplifiers

User Manual

CXD8.4Q — 8 Channel, 4000 W Network Ampliﬁer with Mic/Line Inputs

CXD8.8Q — 8 Channel, 8000 W Network Ampliﬁer with Mic/Line Inputs

CXD8.4Qn — 8 Channel, 4000 W Network Ampliﬁer

CXD8.8Qn — 8 Channel, 8000 W Network Ampliﬁer

TD-001522-01-A

*TD-001522-01*

Page 2

EXPLANATION OF SYMBOLS

The term “WARNING!” indicates instructions regarding personal safety. If the instructions are not followed the result may be bodily injury or death.

The term “CAUTION!” indicates instructions regarding possible damage to physical equipment. If these instructions are not followed, it may result in damage to the equipment that may not be covered under the warranty.

The term “IMPORTANT!” indicates instructions or information that are vital to the successful completion of theprocedure.

The term "NOTE" is used to indicate additional useful information.

The intent of the lightning ﬂash with arrowhead symbol in a triangle is to alert the user to the presence of un-insulated "dangerous" voltage within the product's enclosure that may be of sufﬁcient magnitude to constitute a risk of electric shock to humans.

The intent of the exclamation point within an equilateral triangle is to alert the user to the presence of important safety, and operating and maintenance instructions in this manual.

IMPORTANT SAFETY INSTRUCTIONS

WARNING!: TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any ventilation opening. Install in accordance with the manufacturer's instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus that produce heat.

9. To reduce the risk of electrical shock, the power cord shall be connected to a mains socket outlet with a protective earthing connection.

10. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not ﬁt into your outlet, consult an electrician for replacement of the obsolete outlet.

11. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from theapparatus.

12. Only use attachments/accessories speciﬁed by the manufacturer.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualiﬁed service personnel. Servicing is required when the apparatus has been damaged in any way, such as powersupply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15. The appliance coupler, or the AC Mains plug, is the AC mains disconnect device and shall remain readily operable after installation. On units equipped with powerCon® connectors, the AC Mains disconnect device is the AC Mains plug only; do not use the appliance coupler.

16. Adhere to all applicable, local codes.

17. Consult a licensed, professional engineer when any doubt or questions arise regarding a physical equipment installation.

18. Do not use any aerosol spray, cleaner, disinfectant or fumigant on, near or into the apparatus. Clean only with a dry cloth.

19. Do not unplug the unit by pulling on the cord, use the plug.

20. Do not submerge the apparatus in water or liquids.

21. Keep ventilation opening free of dust or other matter.

A-TD-001522-01

Page 3

Maintenance and Repair

WARNING!: Advanced technology, e.g., the use of modern materials and powerful electronics, requires specially adapted maintenance and repair methods. To avoid a danger of subsequent damage to the apparatus, injuries to persons and/or the creation of additional safety hazards, all maintenance or repair work on the apparatus should be performed only by a QSC authorized service station or an authorized QSC International Distributor. QSC is not responsible for any injury, harm or related damages arising from any failure of the customer, owner or user of the apparatus to facilitate those repairs.

FCC Statement

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCCRules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

RoHS STATEMENT

The QSC CXD8.4Q, CXD8.4Qn, CXD8.8Q and CXD8.8Qn ampliﬁers are in compliance with European Directive 2011/65/EU – Restriction of Hazardous Substances(RoHS2).

The QSC CXD8.4Q, CXD8.4Qn, CXD8.8Q and CXD8.8Qn ampliﬁers are in compliance with “China RoHS” directives. The following chart is provided for product use in China and its territories:

QSC CXD8.4Q, CXD8.4Qn, CXD8.8Q and CXD8.8Qn Ampli󽗉ers

有毒有害物质或元素部件名称 (Part Name)

电路板组件 (PCB Assemblies)

机壳装配件 (Chassis Assemblies) O: 表明这些有毒或有害物质在部件使用的同类材料中的含量是在 SJ/T11363_2006 极限的要求之下。

(O: Indicates that this toxic or hazardous substance contained in all of the homogeneous materials for this part is below the limit requirement in SJ/T11363_2006.)

X: 表明这些有毒或有害物质在部件使用的同类材料中至少有一种含量是在 SJ/T11363_2006 极限的要求之上。 (X: Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials used for this part is above the limit requirement in SJ/T11363_2006.)

(Toxic or hazardous Substances and Elements)

铅

(Pb)

X O O O O O

汞

(Hg)

镉

(Cd)

六价铬 (Cr(vi))

多溴联苯

(PBB)

多溴二苯醚

(PBDE)

Warranty

For a copy of the QSC Limited Warranty, visit the QSC website at www.qsc.com

A-TD-001522-01

Page 4

Unpacking

There are no special unpacking instructions. You may want to keep the shipping material for the unlikely event that the ampliﬁer should need returning for service.

Package Contents

• Quick-Start Guide TD-000476

• Safety Sheet TD-000420

• Ampliﬁer

• Power Cord

• Euro-style Connector Plug, 3-pin (8) (CXD8.4Q and CXD8.8Q only)

• Euro-style Connector Plug, 8-pin (2)

• Euro-style Connector Plug, 3.5 mm, 16-pin (1)

Features

Ampliﬁer Front Panel

Refer to

Ampliﬁer Rear Panel

Refer to

"Ampliﬁer Controls and Indicators" on page 8.

Figure 1 (CXD8.4Q / CXD8.8Q shown)

NOTE: The CXD8.4Qn and CXD8.8Qn models do not have the analog inputs (Item 3 below).

1 3 4 5 6 7 92 8

— Figure 1 —

1. RJ-45 Q-SYS Q-LAN A/B

2. GPIO Euro-style Connector, 16-pin

3. Analog Inputs (1-8) – Eight 3-pin Euro-style Connectors (Only CXD8.4Q and CXD8.8Q models.)

4. Outputs (A-H) – Two 8-pin Euro-style Loudspeaker Connector

Installation

The following steps are written in the recommended installation order.

5. Cooling fan inlet (do not block)

6. AC Power Switch

7. Locking IEC Power Connection

8. Rear Rack-mount Bracket

9. Front Rack-mount Brackets

Rack-Mount the Ampliﬁer

The CXD-Q Series ampliﬁers are designed to be mounted in a standard rack-mount unit. The ampliﬁers are 2RU high, and 381 mm (15 in) deep.

1. Secure the ampliﬁer in the rack with eight screws (not supplied), four in front, four in back. For complete instructions, refer to TD-000050 "Rear Rack Ears Installation Guide" which can be found on the QSC Website (www.qsc.com)

CAUTION!: Be sure that nothing is blocking the front or rear ventilation openings, and that each side has a minimum of 2cmclearance.

A-TD-001522-01

Page 5

Inputs

Balanced

—

Unbalanced

—

Connect the ampliﬁer LAN A, and if available, LAN B, to the Q-LAN network ( requirements and connection detail.

Figure 4

). Refer to your Q-SYS documentation for network

— Figure 2 —

— Figure 3 —

— Figure 4 —

The analog inputs are converted to digital audio in the CXD8.4Q and CXD8.8Q ampliﬁers and then routed to the Q-SYS Core over the network. The digital signals show up in Q-SYS Designer at the CXD-Q input component where they can be routed as needed. Refer to the Q-SYS documentation.

1. Make sure your audio source devices are powered off.

2. Wire the audio mic- or line-level source to up to eight Euro-style connectors (supplied), you can use either balanced inputs ( or unbalanced inputs (

Figure 3

Figure 2

)

3. Plug the connectors into the appropriate receptacles (Routeable Inputs 1, 2, 3, 4, 5, 6, 7, 8)

GPIO

Refer to

"GPIO" on page 13

Figure 4

and

Figure 5

for details about the GPIO feature.

— Figure 5 —

Outputs and Output Conﬁguration

The CXD-Q ampliﬁers have two sets of four-channel outputs that are conﬁgured independently. The conﬁguration of the ampliﬁer is deﬁned in Q-SYS designer software and is "pushed" into the physical ampliﬁer when the Name and Type of ampliﬁer in the design matches the Name and Type of physical ampliﬁer. When the output conﬁguration of the ampliﬁer changes, the Outputs to the loudspeakers change accordingly.

Use the diagrams shown in

Figure 6

thru

Figure 9

connect the wiring based on your conﬁguration. After connecting the loudspeakers to the outputs, you may turn the ampliﬁer on.

CAUTION!: Before turning the amplifier on, double check your output connections to be sure they are connected properly based on the output configuration specified in Q-SYS Designer. If you change the output configuration of the amplifier you must change the loudspeaker connections before applying power to the amplifier! After a change of the output configuration, the amplifier re-boots and all outputs are muted. You must press the Mute All button in the Q-SYS Amp Output component, or unmute all channels on the front panel of the amplifier.

Figure 6

thru

Figure 9 are examples of the three types of output conﬁgurations: Separate, Bridged and Parallel. The tables to the right and left

of the loudspeaker connections (rear panel of the ampliﬁer) give all the possible conﬁgurations and their connections.

A-TD-001522-01

as a reference for planning your loudspeaker conﬁguration. Refer to

Figure 10

for how to

Page 6

Separate Channels (A B C D) and (E F G H)

For Separate Loudspeakers

Use eight 2-wire cables, connect to:

• T1+/T2- (Loudspeaker A / E)

• T3+/T4- (Loudspeaker B / F)

• T5+/T6- (Loudspeaker C / G)

• T7+/T8- (Loudspeaker D / H)

CHANNEL CONFIGURATION

Q A

Q B

4 Channels: A B C D

Channel Configuration Locked to Design

Q C

Q D

CHANNEL CONFIGURATION

Q E

Channel Configuration Locked to Design

Q G

Q F

4 Channels: E F G H

Q H

— Figure 6 —

Bridged (A+B) and Separate (C D) and (E F G H) Channels

For A+B (Bridged) One Loudspeaker

Use one 2-wire cable connect to:

• T1+/T3- (Loudspeaker A+B)

For C D (E F G H) (Separate) Two and Four Loudspeakers

Use six 2-wire cables, connect to:

• T1+/T2- (Loudspeaker E)

• T3+/T4- (Loudspeaker F)

• T5+/T6- (Loudspeaker C / G)

• T7+/T8- (Loudspeaker D / H)

CHANNEL CONFIGURATION

Q A+B

3 Channels: A+B C D

Channel Configuration Locked to Design

Q C

Q D

CHANNEL CONFIGURATION

Q E

Channel Configuration Locked to Design

Q G

Q F

4 Channels: E F G H

Q H

BRIDGED

CH A+B

T1+ T3-

— Figure 7 —

OUTPUTS TO SPEAKERS OUTPUTS TO SPEAKERS

CH D

CH C

CH B

CH A

OUTPUTS TO SPEAKERS OUTPUTS TO SPEAKERS

CH D

CH C

CH B

CH A

CH E

CH F

CH G

CH H

CH E

CH F

CH G

CH H

Two Pair of Parallel Channels (AB CD) and two Pair of Parallel Channels Bridged (EF + GH)

AB (Parallel) CD (Parallel) For Two Loudspeakers

Use two 2-wire cables, connect to:

• T1+/T2- (Loudspeaker AB)

• T5+/T6- (Loudspeaker CD)

EF (Parallel) Bridged with GH (Parallel) For One Loudspeaker

Full power to one loudspeaker Use one 2-wire cable, connect to:

• T1+/T5- (Loudspeaker EF+GH)

CHANNEL CONFIGURATION

Q AB

2 Pair of Paraller Channels: AB CD

Channel Configuration Locked to Design

Q CD

A-TD-001522-01

CHANNEL CONFIGURATION

Q EF+GH

1 Channel: EF+GH

Channel Configuration Locked to Design

CH CD

T5+ T6-

CH AB

T1+ T2-

— Figure 8 —

OUTPUTS TO SPEAKERS OUTPUTS TO SPEAKERS

CH D

CH C

CH B

CH A

CH E

CH F

CH G

CH H

CH EF+GH

T5-

Page 7

Parallel Channels (ABCD) and (E F G H)

CHANNEL CONFIGURATION

1 Channel: A B C D

Channel Configuration Locked to Design

Q ABCD

CH ABCD

CH D

CH A

CH B

CH C

CH E

CH H

CH G

CH F

OUTPUTS TO SPEAKERS OUTPUTS TO SPEAKERS

CHANNEL CONFIGURATION

Channel Configuration Locked to Design

Q EFGH

1 Channel: E F G H

CH EFGH

In 4-1 Parallel (ABCD or EFGH) only T1+, T3+, T5+, and T7+ are electrically the same point T2-, T4-, T6-, and T8- are electrically the same point

SETTINGS CAN BE CONFIGURED FOR

70V, 100V AND

200V DIRECT

OUTPUT.

For One Loudspeaker

Full power to one loudspeaker; Use one 2-wire cable, connect to:

• T3+/T4- (Loudspeaker ABCD)

For Multiple Loudspeakers

Full power for multiple loudspeakers in parallel Use up to four 2-wire cables, connect to:

• T1+/T2- (Loudspeaker E)

• T3+/T4- (Loudspeaker F)

• T5+/T6- (Loudspeaker G)

• T7+/T8- (Loudspeaker H)

— Figure 9 —

Connect the Loudspeakers

1. Connect the loudspeaker wiring to the 8-pin Euro-style connector as needed for your ampliﬁer's conﬁguration.

2. Install the female 8-pin Euro-style connector onto the male connector on the rear of the ampliﬁer as shown in

Figure 10

3. Use a Phillips screwdriver to secure the connector.

AC Mains

WARNING!: When the AC Power is on, there is a potential of having dangerous voltage at the output terminals on the rear of the ampliﬁer. Use caution not to touch these contacts. Turn off the AC Mains disconnect switch prior to making any connections.

1. Make sure the power switch on the rear of the ampliﬁer is off.

2. Connect the IEC power cord to the AC receptacle. (

AC Power On

After connecting the outputs to the loudspeakers, you may turn the ampliﬁer on.

Figure 11

)

— Figure 10 —

1. Make sure the output gain settings for all audio-source devices (CD Players, Mixers, Instruments, etc.) are at the lowest output (max attenuation).

2. Turn on all audio sources.

3. Turn the AC Mains power switch on the back of the ampliﬁer to ON. The ampliﬁer starts in the state it was in when power was removed. If the ampliﬁer is in Standby or Mute All mode (Power button LED solid red or blinking), press the Power button to change the ampliﬁer to Run mode.

4. You can now bring up the outputs of your audio sources.

A-TD-001522-01

— Figure 11 —

Page 8

Ampliﬁer Controls and Indicators

1 2 3

4 5

6 7

9 10 11

— Figure 12 —

14 15

16 17

1. Output Channel labels A, B, C, D, E, F, G, H

2. Output Channel Mute Buttons / LEDs (Red)

3. Output Channel Limiter LEDs (Red)

4. Output Channel -10 dB below maximum ampliﬁer output (Blue)

5. Output Channel -20 dB below maximum

6. Front-panel Power Button (Green/Red)

7. Output Channel Select Buttons / LEDs (Blue)

8. Input Channel Clip LEDs (Red)

9. FAULT LED (Amber)

10. Input Channel Signal-Present LEDs (Blue)

11. Input Channel labels 1, 2, 3, 4, 5, 6, 7, 8

ampliﬁer output (Blue)

NOTE: The following scenarios assume that the ampliﬁer is connected to the Q-SYS Core via Q-LAN. When the ampliﬁer is not connected to the Q-SYS Core, it is in a Fault mode, and not operational unless previously conﬁgured for fail-over or standalone mode as part of a Q-SYS design. With the exception of the Power Switch, found on the rear panel, all of the following

controls are on the front panel.

Refer to

Figure 12

for location of front-panel controls.

Ampliﬁer Modes

Off Mode

• Rear-panel power switch is off, the ampliﬁer

is not operable. The power switch is the AC

Mainsdisconnect.

• The front-panel power button (6) is notilluminated.

• Turn the power switch to ON. The ampliﬁer enters the

mode in which it was when power was removed – Run, Mute All, orStandby.

Run Mode

• From Standby or Mute All mode, press and release the power

button on the front panel. The ampliﬁer is in Run Mode.

• The power button (6) is illuminated green.

• The ampliﬁer is fully operable; audio can pass.

Standby Mode

• From Mute All or Run mode, press and hold the power button (6)

on the front panel for approximately four seconds.

• The power button illuminates solid red.

• The ampliﬁer is not operable; audio will not pass.

Mute All Mode

• From the Run Mode, quickly press and release the power button (6).

• The power button ﬂashes red, all output Mute buttons (2) are red.

• The ampliﬁer output is disabled, but the front panel is fullyoperable.

Power Switch

Power Button

12. LCD Graphic Display

13. NEXT Button

14. PREV Button

15. MASTER CONTROL Knob

16. ID Button

17. Pinhole Reset

Controls

SEL Buttons (7)

• Channel gain can be adjusted from the Q-SYS Designer software or from the front panel of the ampliﬁer.

• Use the SEL button to select one or more than one channel to change gain settings. All selected channels will change at the same time.

• If two or more outputs are bridged or in parallel, pressing one button in the group selects all channels in that bridged or parallel group.

NEXT (13) and PREV (14) Buttons

• Navigates forward and backwards through the screens.

Master Control Knob (15)

• Adjusts the Gain for the selected channel or channels. At least one channel must be selected.

• When one or more channels are selected, turn the Master Control knob to jump to the Gain screen. After a few seconds with no activity, it returns to the earlier screen.

• If there is more than one channel selected, and the gains for those channels are different, the difference is maintained unless the gain is raised or lowered to the limits for both channels.

ID Button (16)

• Press this button to display a screen with the ampliﬁer's network name. In addition, the ID buttons on the associated Q-SYS Ampliﬁer component and the associated Q-SYS Conﬁgurator item ﬂashes. Press again, or click one of the other ID buttons, to stop the ﬂashing and exit the screen.

Pinhole Reset (17)

• Insert a paper clip or similar tool into the pinhole, press and hold for 3 sec. then press the ID button to conﬁrm and reset the ampliﬁer. Default settings include network settings to Auto, Ampliﬁer Name, password, and log ﬁle.

SEL

A-TD-001522-01

Page 9

Input and Output Signal Flow

Q-LAN

5 61 2 3 74

51 2 3 4

CXD8.4Q and CXD8.8Q

Refer to

The CXD8.4Q and CXD8.8Q ampliﬁers have eight MIC/LINE inputs and eight (two blocks of four) ampliﬁed outputs on the rear of the ampliﬁer. The inputs and outputs are not physically (or electrically) connected in the ampliﬁer giving you the ﬂexibility to use any available source in Q-SYS for the ampliﬁed outputs, and to route the inputs to any output. The inputs and outputs can be connected in your Q-SYS design as shown in

1. The analog inputs are converted to digital audio in the ampliﬁer

2. The converted audio is then routed to the Q-SYS Core via Q-LAN (LAN A, LAN B).

3. The digital signals are brought into the design via the ampliﬁer's Mic/Line Input component.

4. From the Mic/Line Input component the signals can be sent for processing and can be sent anywhere within the Q-SYS system.

5. In the Q-SYS Core digital audio signals (not necessiarily from the amp's inputs) are sent to the Q-SYS Amp Output component.

6. The digital audio is then sent from the Q-SYS Core via Q-LAN to the ampliﬁer.

7. Digital signals are converted to analog, ampliﬁed and sent to outputs of the ampliﬁer.

Figure 13

12V Phantom

21 43

65 87

ROUTABLE INPUTS

MIC/LINE

Ampliﬁer

Rear Panel

Inputs

Mic/Line

Input

CXD-Q

Q-SYS

DSP

Routing

Q-SYS Core

— Figure 13 —

Amp Output

Ampliﬁer-1

CXD-Q

QSC

Loudspeakers

Ampliﬁer

Rear Panel

Outputs

The Q-SYS Amp Output component can have two to eight inputs/outputs depending on the conﬁguration of the ampliﬁer in Q-SYS Designer. The desired conﬁguration is selected in the Q-SYS Designer Properties menu for the ampliﬁer. When the ampliﬁer's conﬁguration is changed, all of the outputs are placed in a "mute all" state. You must un-mute all in the Amp Output component's control panel or on the ampliﬁer's front panel.

CXD8.4Qn and CXD8.8Qn

Refer to

The CXD-Qn model ampliﬁers have no analog inputs. The input signal utilized to drive the ampliﬁer channels must be virtually wired in Q-SYS Designer. The CXD-Qn models have eight (two blocks of four) ampliﬁed outputs on the rear of the ampliﬁer.

1. Digital audio is sent to the Q-SYS Core via Q-LAN (LAN A, LAN B).

2. In the Core, the signals can be sent for processing and can be sent anywhere within the Q-SYS system.

3. In the Q-SYS Core digital audio signals are sent to the Q-SYS Amp Output component.

4. The digital audio is then sent from the Q-SYS Core via Q-LAN to the ampliﬁer.

5. Digital signals are converted to analog, ampliﬁed, and sent to the outputs of the ampliﬁer.

Figure 14

Q-SYS

DSP

Routing

Q-LAN

The Amp Output component can have two to eight outputs depending on the conﬁguration of the ampliﬁer in Q-SYS Designer. The desired conﬁguration is selected in the Q-SYS Designer Properties menu for the ampliﬁer. When the ampliﬁer's output conﬁguration is changed, all of the outputs are placed in a "mute all" state. You must unmute all in the Amp Output component's control panel or on the ampliﬁer's front panel.

A-TD-001522-01

Amp Output

Ampliﬁer-1

CXD-Qn

Q-SYS Core

— Figure 14 —

QSC

Loudspeakers

Q-LAN

Ampliﬁer Rear

Panel Outputs

Page 10

Screens

2 3 4 51

Channel Conﬁguration Screens

Figure 15

CONFIGURATION. Inputs (Q) are from Q-SYS, outputs A–D (E–H not shown) represent the ampliﬁer channels and their conﬁguration.

2. Text indicating how many channels, and the output conﬁguration. For possible conﬁgurations refer to the Q-SYS help for the ampliﬁercomponents.

3. Status of the ampliﬁer and Q-SYS design indicating the design and amp are in sync.

Routable MIC/LINE Inputs

This screen is not available on the CXD-Qn model ampliﬁers.

Figure 16

not shown) which displays the status of the physical MIC/LINE INPUTS for the Q models.

1. Input channels are identiﬁed numerically, 1–4 (and 5–8 not shown)

2. Input Level – is the Peak Input Level (dBFS) and is the same as displayed in the Q-SYS Mic/ Line Input component.

3. Muted – when illuminated indicates that the Input is muted for the associated channel. This is controlled by the Mute button on the Q-SYS Designer Mic/Line Input component. Input

channels cannot be muted from the ampliﬁerinterface.

4. Clip – indicators illuminate when the input to the Mic/Line Input component is too high. Adjust the Preamp Gain on the Mic/Line Input component in Q-SYS Designer.

5. P12 – phantom power (+12V) is available for microphones (condenser) requiring power. You can turn the phantom power on/off in the Mic/Line Input component in Q-SYS Designer.

is a graphic representations of the ampliﬁer's output CHANNEL

shows the Routable MIC/LINE INPUTS screen for channels 1–4, (channels 5–8

CHANNEL CONFIGURATION

Q A

Channel Configuration Locked to Design

Q B

4 Channels: A B C D

— Figure 15 —

ROUTABLE MIC/LINE INPUTS

INPUT LEVEL MUTED CLIP P12

— Figure 16 —

Q C

Q D

Status Screen

Refer to

1. DEVICE – the hostname (network name) of the ampliﬁer. A default name is

2. DESIGN – the name of the Q-SYS design currently running on the ampliﬁer. The

3. STATUS – displays the current status of the ampliﬁer both in text and color. The

4. FIRMWARE – the Q-SYS Designer ﬁrmware version installed on the ampliﬁer.

To Update the Ampliﬁer Firmware:

A-TD-001522-01

Figure 17

given at the factory, similar to the example. You may change the name in the Q-SYS onﬁgurator.

ampliﬁer must be contained in a running design tooperate.

following is a list of possible status colors, and some example conditions.

• OK – green – audio is good, hardware is good.

• Compromised – orange – audio is good but a redundancy mechanism is active (one

LAN down but the other is still up) or a non-fatal hardware problem exists (fan speed, high temperature, low AC voltage, output load, ampliﬁer is in Protect mode, etc.)

• Fault – red – audio is not passing, or hardware is malfunctioning or mis-conﬁgured (ampliﬁer power off, audio streams broken, ampliﬁer fault,

loudspeaker short circuit, etc.)

• Initializing – blue – In the process of initialization, and design start. Audio is not passed.

NOTE: The CXD-Q 8-channel ampliﬁers require Version 6.1 or later of Q-SYS Designer.

a. Install the version of Q-SYS Designer you want to use on your PC.

b. The ampliﬁer must be connected to Q-LAN and turned on.

c. Open the Q-SYS design containing the ampliﬁer in the Designer version you just installed.

d. Select "Save to Core and Run" from the File menu.

e. The ampliﬁer and any other Q-SYS peripherals in the design are automatically updated.

STATUS

DEVICE: CXDQ8CH-1234

DESIGN: My Design Filename

STATUS: OK

FIRMWARE: 6.1.00

— Figure 17 —

Page 11

LAN A / LAN B Screen

HEALTH

4 5

2 31

Refer to

1. IP ADDRESS – a default address is assigned in the factory. You can change this

2. NETMASK – must be the same as the Core's Netmask.

3. GATEWAY – must be the same as the Core's Gateway.

4. LAN B is not required. When connected, the same type of information as LAN A is displayed.

Figure 18

and the other parameters in Q-SYS Conﬁgurator. LAN A is required, and cannot be turned off.

Health Screen

Refer to

1. FAN RPM – varies depending on the temperature.

2. PSU TEMP – varies depending on operating conditions. PSU Temp is monitored

3. AC VOLTAGE – AC Mains voltage

4. AC CURRENT – AC mains current drawn by the ampliﬁer.

5. Voltage Rails

Figure 19

and can automatically put the amp into limiting or shutdown if safe operating temperatures are exceeded.

• V RAIL 1 = +147VDC +/- 5V typical

• V RAIL 2 = -147VDC +/- 5V typical

LAN A (AUTO)

IP ADDRESS:

NETMASK:

GATEWAY:

LAN B (AUTO, NO LINK)

IP ADDRESS:

NETMASK:

GATEWAY:

192.168.xxx.xxx

255.255.0.0

— Figure 18 —

FAN RPM:

PSU TEMP: 35.3°C

AC VOLTAGE: 115V

AC CURRENT: 1.61A

V RAIL 1: 145V

V RAIL 2: -149V

1109

— Figure 19 —

OUTPUT GAINS Screen

Refer to

The Output Gain screens provides a quick overview of all outputs. In addition, when this screen is displayed, you can make GAIN adjustments on the ampliﬁer's front panel. There is one screen for channels A–D and one for channels E–H.

Use the NEXT or PREV buttons to access these screens or, press one or more of the SEL buttons to access the screen.

1. The highlighted background indicates that the Channel is selected by the SEL button.

2. Channel – the channels display according to the conﬁguration of the ampliﬁer.

3. Output Gain – the output gain can be controlled in two places: the GAIN knob on

4. Q-LAN Input Level – the level of the audio signal applied to the Output component in the Q-SYS design. The CXD-Q Output component is

5. VOLTS – the voltage applied to that output.

6. Output B is combined with Output A – (AB or A+B), the slot for Output B is blank.

To Make Gain Adjustments:

Figure 20

the ampliﬁer front panel and with the Gain control in the ampliﬁer's Output component in the Q-SYS design.

the connection to the output section of the ampliﬁer.

a. Use the SEL button to select one or more channels. You can select any or all channels.

b. Use the GAIN knob to make adjustments on the output gain of the selected channels.

OUTPUT GAINS

-45.0 dB

Q-LAN: -8.08 dB

VOLTS: 101 V

Q-LAN:

VOLTS:

Q-LAN:

VOLTS:

-100.0 dB

.014 V

-100 dB

.014 V

— Figure 20 —

NOTE: If the gains were the same when you select multiple channels the gains remain equal as you adjust them. If the gains are different, they keep their relative separation until one reaches a limit. At this point the other channel(s) continue to change until they reach the limit.

NOTE: If you press one or more of the SEL buttons, and do not make any GAIN adjustments, this screen remains visible for a short time then returns to the previous screen.

A-TD-001522-01

Page 12

Output Screens

2 3 4 5

Each group of outputs has a dedicated screen.

1. Output channel identiﬁers A – D and E – H (not shown).

2. DAC – when illuminated, this indicates that the signal to the D to A Converter is larger than can be reproduced and a limiter has been engaged to prevent clipping.

3. PROTECT – when illuminated, this indicates that the ampliﬁer is in Protect Mode. Usually due to the power supply going above its thermal threshold.

4. LIMIT – when illuminated, this indicates the ampliﬁer limiter is active. There are ﬁve conditions that could cause the LIMIT condition:

• Power

• Current

• Voltage

• Temperature

• Loudspeaker Protection is active.

5. SHORT – when illuminated, this indicates the output is shorted. A short can be triggered by either of the following:

a. Output impedance is below ¼ Ohm for more than 1 second.

b. Output voltage is less than 50% of what the DSP was expecting for more than 1 second.

6. Displays the temperature, in Centigrade, of the associated channel.

Figure 21

is an example of OutputsA–D.

DAC PROTECT LIMIT SHORT 43.05ºC

DAC PROTECT SHORT 42.16ºC

DAC PROTECT SHORT 43.06ºC

DAC PROTECT SHORT 41.05ºC

— Figure 21 —

OUTPUT

LIMIT

A-TD-001522-01

Page 13

GPIO

10 kΩ

There are 16 General Purpose Input Output pins for use in various applications.

rear of the ampliﬁer. — Table 1 shows the connector pin-out. Figure 23 gives some simple GPIO applications.

— Table 1 —

Connector Pin GPIO # and

Speciﬁcations

Function

1 3.3 V 100 mA max (power cycle to reset current limiting)

2 GPIO 1 5mA in/out, 3.3V max, 127Ω resistor in series

3 GPIO 2 5mA in/out, 3.3V max, 127Ω resistor in series

4 GND Ground

5 GPIO 3 5mA in/out, 3.3V max, 127Ω resistor in series

6 GPIO 4 5mA in/out, 3.3V max, 127Ω resistor in series

7 GND Ground

8 GPIO 5 18mA in/out max, 3.3V max, 127Ω resistor in series

9 RELAY NO

10 RELAY COM

11 RELAY NC

12 GND Ground

13 GPIO 6 18mA in/out max, 3.3V max, 127Ω resistor in series

14 GPIO 7 18mA in/out max, 3.3V max, 127Ω resistor in series

15 GND Ground

16 GPIO 8 18mA in/out max, 3.3V max, 127Ω resistor in series

1 Nominal switching capacity is 30 VDC at 2 A for a total of 60 W maximum. The maximum

voltage is 220 VDC if the current is limited to observe the maximum power rating (60 W).

Relay Normally Open

Relay Common

Relay Normally Closed

Figure 22 shows the pin conﬁguration for the connector on the

1 2 3 4 5 6 7 8

— Figure 22 —

9 10 11 12 13 14 15 16

Examples

Button or Contact Closure Potentiometer Q-SYS-Powered LED

GPIO

Ground

+3.3 V

GPIO

Analog In

Ground

— Figure 23 —

GPIO 5-8

Ground

Works for LEDs up to 18 mA. Current is limited in the GPIO

circuit by a 127Ω resister in series.

A-TD-001522-01

Page 14

Speciﬁcations

CXD8.4Q / CXD8.4Qn CXD8.8Q / CXD8.8Qn

Channel Conﬁguration

Max Power

Continuous

70 V 500 W 300 W 850 W 600 W

100 V 500 W 300 W 850 W 600 W

8 Independent Channels

A, B, C, D, E, F, G, H

8Ω 500 W 300 W 850 W 600 W

4Ω 500 W 300 W 1000 W 600 W

2Ω 500 W 300 W 600 W 300 W

2 Channels Combined in BTL Bridge

A+B or C+D or E+F or G+H

Doubles Voltage

2 Channels Combined in Parallel

AB or CD or EF or GH

Doubles Current

3CH Combined in Parallel

ABC or EFG

Triples Current

4CH Combined in Bridged/Parallel

AB+CD

Doubles Current and Voltage

4CH Combined in Parallel

ABCD or EFGH

Quadruples Current

8Ω 1000 W

4Ω NR

2Ω NR 4 NR

8Ω 1000 W 600 W 1100 W 1100 W

4Ω 1000 W

2Ω 1000 W

8Ω 1000 W 900 W 1100 W 1100 W

4Ω 1500 W 900 W 1800 W 1800 W

2Ω 1500 W 900 W 2800 W 1800 W

8Ω 2000 W

4Ω 2000 W

2Ω NR

8Ω 1200 W 1200 W 1200 W 1200 W

4Ω 2000 W 1200 W 2200 W 2200 W

2Ω 2000 W

600 W

1200 W

CXD8.4Q / CXD8.4Qn CXD8.8Q / CXD8.8Qn

Typical distortion

8Ω

4Ω

Maximum distortion

4Ω - 8Ω 1.0% 1.0%

Frequency response (8Ω) 20 Hz – 20 kHz +/- 0.3 dB 20 Hz – 20 kHz +/- 0.3 dB

Noise

Unweighted output muted

Weighted output muted

Gain (1.2V setting) 35.4 dB 38.4 dB

Damping factor >100 >100

Input impedance >8k balanced and >4k unbalanced >8k balanced and >4k unbalanced

Input Sensitivity

Continuously variable:

Controls and indicators (front) Power • Channel MUTE Buttons • Channel SELECT Buttons • Channel Input Signal and CLIP LED Indicators •

Channel Output and LIMIT LED Meters • NEXT, PREV, ID Buttons • Control Knob • Reset Button

Controls and indicators (rear) AC Power Disconnect (IEC Power cord and/or AC Power switch)

Input connectors 3-pin Phoenix

Output connectors 8-pin Phoenix Speaker

Ampliﬁer and load protection Short circuit • open circuit • thermal • RF protection • On/Off muting • DC fault shutdown • active inrush limiting

AC power input Universal input power supply with active power factor correction 100 - 240 VAC, 50 - 60 Hz

0.02 – 0.05%

0.04 – 0.1%

>101 dB

>104 dB

Vrms

1.23mV to 17.35V

dBu

-56 to 27

dBv

-58.2 to 24.8

Max Power

2000 W

1800 W

2000 W

3600 W

4500 W

4000 W

Continuous

1200 W

NR 4 NR

1200 W

600 W

2400 W

0.02 – 0.05%

0.04 – 0.1%

>101 dB

>104 dB

Vrms

1.23mV to 17.35V

dBu

-56 to 27

dBv

-58.2 to 24.8

A-TD-001522-01

Page 15

CXD8.4Q / CXD8.4Qn CXD8.8Q / CXD8.8Qn

Weight, net / shipping 25 lb (11.3 kg) / 29 lb (13.2 kg) 26 lb (11.8 kg) / 30 lb (13.6 kg)

Dimensions (HWD) 3.5” x 19” x 16” (89mm x 482mm x 406mm)

Agency approvals UL • CE • RoHS/WEEE compliant • FCC Class B (conducted and radiated emissions)

Carton contents Quick-Start Guide • Safety Sheet • Ampliﬁer • Power Cord • Euro-style Connector Plug, 3-pin • Euro-style

1 Max Power – 20 ms 1 kHz sine burst, all channels driven 2 Continuous Power – EIA 1 kHz 1% THD, all channels driven 3 BOLD = Optimal conﬁguration for the load and channel count 4 NR = Not Recommended due to excessive current draw

Connector Plug, 8-pin) • Euro-style Connector Plug, 3.5 mm, 16-pin

Heat Loss and Current-Draw Charts

Heat losses are the thermal emissions from an ampliﬁer while it is operating. It comes from dissipated waste power—i.e., real AC power in minus audio power out. Measurements are provided for various loads at idle, 1/8 of average full power, 1/3 of average full power, and full power, with all channels driven simultaneously. For typical usage, use the idle and 1/8 power ﬁgures. This data is measured from representative samples; due to production tolerances, actual heat emissions may vary slightly from one unit to another. Bridged mono into 8 ohms is equivalent to 4 ohms per channel; into 4ohms is equivalent to 2 ohms per channel.

Idle

Thermal loss at idle or with very low signal level.

1/8 Power

Thermal loss at 1/8 of full power is measured with a 1 kHz sine wave signal. It approximates operating with music or voice with light clipping and represents the ampliﬁer's typical "clean" maximum level, without audible clipping. Use these ﬁgures for typical maximum level operation.

1/3 Power

Thermal loss at 1/3 of full power is measured with pink noise. It approximates operating with music or voice with very heavy clipping and a very compressed dynamic range.

Full Power

Thermal loss at full power is measured with a 1 kHz sine wave. However, it does not represent any real-world operating condition.

Current Draw

The amount of AC current an ampliﬁer demands while it is operating. Measurements are provided for various loads at idle, 1/8 of average full power, 1/3 of average full power, and full power, with all channels driven simultaneously. The data shown in the following tables is listed for 100VAC, 120VAC and 230VAC operation. For typical usage, use the idle and 1/8 power data.

NOTE: 25V, 70V, 100V modes are not rated.

A-TD-001522-01

Page 16

100VAC Operation

Load per Channel 8Ω 4Ω 2Ω

BTU/hr kcal/hr Amperes BTU/hr kcal/hr Amperes BTU/hr kcal/hr Amperes BTU/hr kcal/hr Amperes

Idle

CXD8.4Q / CXD8.4Qn 543 137 1.7

CXD8.8Q / CXD8.8Qn 631 159 1.0

1/8th Power

CXD8.4Q / CXD8.4Qn 971 245 6.2 1132 285 6.7 1399 353 7.5

CXD8.8Q / CXD8.8Qn 1273 321 10.8 1277 322 11.0 1457 367 8.9

1/3rd Power

CXD8.4Q / CXD8.4Qn 1447 365 13.1 1802 454 14.3 2297 579 15.7

CXD8.8Q / CXD8.8Qn 1806 455 23.0 2199 552 23.8 2451 618 16.7

Full Power

CXD8.4Q / CXD8.4Qn 2526 637 33.9 3768 950 37.1 5795 1460 43.6

CXD8.8Q / CXD8.8Qn 6986 1760 74.9 8065 2032 77.9 4925 1241 40.2

120VAC Operation

Load per Channel 8Ω 4Ω 2Ω

BTU/hr kcal/hr Amperes BTU/hr kcal/hr Amperes BTU/hr kcal/hr Amperes BTU/hr kcal/hr Amperes

Idle

CXD8.4Q / CXD8.4Qn 548 138 1.4

CXD8.8Q / CXD8.8Qn 642 162 1.6

1/8th Power

CXD8.4Q / CXD8.4Qn 942 237 5.0 1100 277 5.4 1385 349 6.1

CXD8.8Q / CXD8.8Qn 1352 341 9.4 1317 332 9.4 1519 383 8.0

1/3rd Power

CXD8.4Q / CXD8.4Qn 1362 343 10.5 1700 428 11.4 2259 569 12.6

CXD8.8Q / CXD8.8Qn 1976 498 19.3 2474 623 20.3 2461 620 14.0

Full Power

CXD8.4Q / CXD8.4Qn 2601 655 27.3 3304 833 29.1 5546 1398 34.6

CXD8.8Q / CXD8.8Qn 5140 1295 55.0 6137 1547 57.4 4358 1098 31.9

230VAC Operation

Load per Channel 8Ω 4Ω 2Ω

BTU/hr kcal/hr Amperes BTU/hr kcal/hr Amperes BTU/hr kcal/hr Amperes BTU/hr kcal/hr Amperes

Idle

CXD8.4Q / CXD8.4Qn 546 138 0.9 — — — — — — — — —

CXD8.8Q / CXD8.8Qn 580 146 1.2 — — — — — — — — —

1/8th Power

CXD8.4Q / CXD8.4Qn 889 224 2.6 1008 254 2.8 1253 316 3.1

CXD8.8Q / CXD8.8Qn 1290 325 5.0 1399 353 5.1 1556 392 5.4

1/3rd Power

CXD8.4Q / CXD8.4Qn 1399 353 5.5 1621 408 5.9 2020 509 6.4

CXD8.8Q / CXD8.8Qn 1980 499 10.1 2263 570 10.3 2164 545 7.6

Full Power

CXD8.4Q / CXD8.4Qn 2280 575 13.9 2826 712 14.5 4730 1192 17.0

CXD8.8Q / CXD8.8Qn 3748 944 26.3 4638 1169 27.5 3843 968 16.4

A-TD-001522-01

— — — — — — — — —

Page 17

Mailing Address:

Customer Support

QSC, LLC

1675 MacArthur Boulevard

Q-SYS 24/7 Emergency Support*

Tel: +1.888,.252.4836 (U.S./Canada)

Tel: +1.949.791.7722 (non-U.S.)

Q-Sys™

Costa Mesa, CA 92626-1468 U.S.

Main Number: +1.714.754.6175

World Wide Web: www.qsc.com

Sales & Marketing:

Voice: +1.714.957.7100 or toll free (U.S. only) 1.800.854.4079

FAX: +1.714.754.6174

E-mail: info@qsc.com

Q-SYS™ Customer Support

Application Engineering and Technical Services

Monday - Friday 7 AM to 5 PM PST (Excludes Holidays)

Tel. 1.800.772.2834 (U.S. only)

Tel. +1.714.957.7150

*Q-SYS 24/7 Support is for Emergency assistance with Q-SYS systems only. 24/7 support guarantees a call back within 30 min after a message is left. Please include, Name, Company, Call Back Number and description of the Q-SYS emergency for prompt call back. If calling during business hours please use the standard support numbers above.

Q-SYS Support Email

qsyssupport@qsc.com

(Immediate email response times not guaranteed)

QSC

Technical Services

1675 MacArthur Blvd.

Costa Mesa, CA 92626 U.S.

Tel: 1.800.772.2834 (U.S. only)

Tel: +1.714.957.7150

FAX: +1.714.754.6173

countries. All other trademarks are the property of their respective owners.

A-TD-001522-01

http://patents.qsc.com.

QSC CXD8.4Q, CXD8.8Qn, CXD8.8Q User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual